This script hasn't seen an update in multiple years, update it to the
latest version provided upstream. Both `config.guess` and `config.sub`
are copied from upstream[1] and not modified.
The full changelog is available within the upstream repository[1].
[1]: https://git.savannah.gnu.org/git/config.git
Signed-off-by: Paul Spooren <mail@aparcar.org>
This update only adds one commit:
b102f19bcc53 tests: Opportunistic Wireless Encryption - SA Query
The main reason for the bump is to have a newer PKG_SOURCE_DATE,
so we can reset PKG_RELEASE to 1 (this has not been done for the
most recent bump), and replace it with AUTORELEASE.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Move code above interface generation
It results in more logical order. Device gets its config section
above interface section.
2. Drop the loop
We have separated code handling bridges now so $device should be
guaranteed to contain a single device name.
3. Drop section name
It's not required by netifd or LuCI & it's not needed by this script
as $device contains a single device name now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The underlying logread process uses usock() to handle remote connections
which is able to handle both hostnames and IP addresses.
Ref: https://github.com/openwrt/luci/issues/5077
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug
wireless router. This device is also sold under the name SilverCrest
SWV 733 A2.
Device Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high
- Buttons: Reset, WPS
- Sliding mode switch: AP, repeater, client
- Small sliding power switch
Flashing instructions:
U-Boot launches TFTP client if WPS button is pressed during power-on.
Configure as follows:
- Server IP: 192.168.10.100
- Filename (rename sysupgrade file to this): firmware.bin
Flashing should not take more than a minute, device will reboot
automatically.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Channel 100 is a valid channel to choose for 80MHz operation. However,
it's assigned to 5500 MHz, not 5550MHz. In fact, there is no channel
assigned to this frequency.
Fix this obbvious typo to allow ACS to select channel 100 for 80 MHz
operation again.
Signed-off-by: David Bauer <mail@david-bauer.net>
The patch was not applied to the v5.4 target, thus breaking Kernel 5.4
on devices with multiple flash chips attache to the SPI bus.
Fixes commit bd54e73954 ("ath79: set number of chipselect lines")
Signed-off-by: David Bauer <mail@david-bauer.net>
The name of the module is 'uleds', not 'leds-uleds'.
Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com>
[improve commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications
SoC: MT7621
CPU: 880 MHz
Flash: 16 MiB
RAM: 128 MiB
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac
MT7603E / MT7615E
Ethernet: 5x Gbit ports
Installation
There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
The router will request 'recovery.bin' from a TFTP server at
192.168.1.88.
Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.
R4 & R5 need to be shorted (0-100Ω) for the UART to work.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[remove non-required switch-port node - remove trgmii phy-mode]
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for TP-Link Archer C6U v1 (EU).
The device is also known in some market as Archer C6 v3.
This patch supports only Archer C6U v1 (EU).
Specifications:
--------------
* SoC: Mediatek MT7621AT 2C2T, 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (Winbond 25Q128)
* WiFi 5GHz: Mediatek MT7613BEN (2x2:2)
* WiFi 2.4GHz: Mediatek MT7603EN (2x2:2)
* Ethernet: MT7630, 5x 1000Base-T.
* LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB
* Buttons: Reset, WPS.
* UART: Serial console (115200 8n1), J1(GND:3)
* USB: One USB2 port.
Installation:
------------
Install the OpenWrt factory image for C6U is from the
TP-Link web interface.
1) Go to "Advanced/System Tools/Firmware Update".
2) Click "Browse" and upload the OpenWrt factory image:
openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin.
3) Click the "Upgrade" button, and select "Yes" when prompted.
Recovery to stock firmware:
--------------------------
The C6U bootloader has a failsafe mode that provides a web
interface (running at 192.168.0.1) for reverting back to the
stock TP-Link firmware. The failsafe interface is triggered
from the serial console or on failed kernel boot. Unfortunately,
there's no key combination that enables the failsafe mode. This
gives us two options for recovery:
1) Recover using the serial console (J1 header).
The recovery interface can be selected by hitting 'x' when
prompted on boot.
2) Trigger the bootloader failsafe mode.
A more dangerous option is force the bootloader into
recovery mode by erasing the OpenWrt partition from the
OpenWrt's shell - e.g "mtd erase firmware". Please be
careful, since erasing the wrong partition can brick
your device.
MAC addresses:
-------------
OEM firmware configuration:
D8:07:B6:xx:xx:83 : 5G
D8:07:B6:xx:xx:84 : LAN (label)
D8:07:B6:xx:xx:84 : 2.4G
D8:07:B6:xx:xx:85 : WAN
Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
The patch adds support for the TP-Link Archer A6 v3
The router is sold in US and India with FCC ID TE7A6V3
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated from serial console only.
Press 'x' while u-boot is starting
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Thanks to: Frankis for Randmon MAC address fix.
Signed-off-by: Vinay Patil <post2vinay@gmail.com>
[remove superfluous factory image definition, whitespacing]
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes Gateworks Ventana 'DEVICE_NAME' variable which value wasn't
adjusted during migration to common 'vendor_model' image naming scheme
(fixes: FS#3825).
Furthermore, drop unused 'Build/boot-scr' recipe, get rid of redundant
'BOOT_SCRIPT' variable (use already provided 'DEVICE_NAME' instead) and
drop custom 'DEVICE_NAME' variable from SolidRun CuBox-i image recipe
(use default one instead).
Fixes: cbc8bcfbaa ("imx6: image: use vendor_model scheme")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This fixes `iw dev wlan0-mesh station dump`.
8fab0c9 iw: fix ftm_request missing arguments segfault
e816fbc iw: fix mgmt dump missing arguments segfault
5d9d1b8 iw: Fix timestamp output on 32-bit architectures
4b25ae3 iw: fix pointer arithmetic in __print_he_capa
c3df363 iw: add option to print human readable event time
cd64525 iw: print ctrl port tx status event
0ba98b9 iw: use correct type in policy check for mesh
9e38dee iw: scan: fixup HE caps whitespace
17e8564 iw: scan: parse HE capabilities
5735e58 iw: util: factor out HE capability parser
6d8d507 iw: scan: add extension tag parsing
b4e1ec4 man: update wikipage URL, reformat SEE ALSO section
c56036a iw: enable 80MHz support for 6GHz band 11s mesh
fa72728 iw: handle positive error codes gracefully
7ba9093 iw: scan: add flag for scanning colocated ap
5ec60ed iw: Add 'coloc' and 'flush' options to sched_scan
f8ade75 iw: update wikipage URL
b6f2dac iw: Add support for specifying the 160MHz bandwidth when setting the channel/frequency
Signed-off-by: Andre Heider <a.heider@gmail.com>
Instead of requiring the user to call it on each BSS individually,
run it on all BSSs internally.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
899c2a4 interface: support "device" attribute and deprecate "ifname"
62e3cb5 scripts/netifd-wireless.sh: add support for specifying the operating band
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Use SPDX license headers to be machine readable.
2) Update copyright to 2021.
3) Use $(PROJECT_GIT) instead of manually specifying the git url.
4) Use $(AUTORELEASE) to automatically set the correct PKG_RELEASE.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes a regression introduced with commit
5ed1e5140a ("build: build kernel image
before building modules/packages").
Before this commit the make target would always include "modules",
resulting in a MODPOST and a complete Module.symvers file. Since this
commit a MODPOST of the kernel modules is not guaranteed for kernels <
5.10. This results in some broken SDKs in which external packages that
depend on exported symbols from kernel modules fail to compile.
Adding "modules" back to the calls to the CompileImage defines fixes the
regression. For kernels > 5.10 this is not needed, but it doesn't cause
any harm either.
Tested with kernels 5.4.x and 5.10.x.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
The SRV was added some time ago and should be mentioned in the short
help message to avoid confusion about missing features.
Signed-off-by: Paul Spooren <mail@aparcar.org>
0d5860d fix memory leak in nat46_netdev_destroy().The netdev is forgotten to free in nat46_netdev_destroy function (#26)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
After the commit 43fc720657
("base-files: generate "device UCI type section for bridge"), the wrong
network configuration is generated for the devices that already have the
bridge device section for VLAN, such as the devices in realtek target.
As a result, the bridge device by additional "device" section is
specified to the "ports" option in the "bridge-vlan" section and netifd
shuts down the switch and the ethernet when the network service started.
Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rmilecki: use $ports for generate_bridge_vlan argument]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This marks all packages which depend on a target with @TARGET nonshared.
If they are not marked nonshared they would be build by the SDK build
and if this happens with a different SDK, then the SDK from the target
the package depends on, the package would not be added to the index.
This should fix the image builder for some of these packages.
This should fix the image builder at least for bcm27xx/bcm2710 and
bcm4908/generic.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the patches to match the versions included in the mtd
subsystem for the next Linux kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rid of kernel error message:
[ 0.780828] orion-mdio d0072004.mdio: IRQ index 0 not found
on Marvell targets backporting the kernel commit fa2632f74e57
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The higher 16-bit of EEE register was overwritten by mistake, fix that.
Fixes: 5b9ba4a93e ("generic: mt7530: support adjusting EEE")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
This adjusts the Makefile to use the new option to turn off the
doc builds. It will not cause any problems except a warning
about unused options if combined with a ccache source missing
the upstream patch.
Since a config setting is required to re-enable the doc build this
is equivalent to unconditionally disabling the docs if the config
setting is not created.
Signed-off-by: David Adair <djabhead@aol.com>
