Add kernel support for SAMA7G5 by back-porting mainline kernel patches.
Among SAMA7G5 features could be remembered:
- ARM Cortex-A7
- double data rate multi-port dynamic RAM controller supporting DDR2,
DDR3, DDR3L, LPDDR2, LPDDR3 up to 533MHz
- peripherals for audio, video processing
- 1 gigabit + 1 megabit Ethernet controllers
- 6 CAN controllers
- trust zone support
- DVFS for CPU
- criptography IPs
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
The file can't be part of base files or the base-files and firewall
packages collide. Two packages must not provide the same config files
without having a defined CONFLICT since it would result in an
undeterministic config state depending on what package is installed
last.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D2 ICP board.
Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
One ETH switchport,
One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
Bluetooth module (Wi-Fi/BT), suitable for
Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
(PAC1934)
Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux
Flashing:
- follow the procedure at [2]
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Bump at91 targets to kernel v5.10. With this patches and files for
wb45n and wb50n were removed as they are now included in upstream
kernel. Along with:
- this the kernel config for sama5d2 and sam9x targets has been
refreshed (with make kernel_menuconfig + save);
- CONFIG_ARCH_AT91 and specific sam9x SoCs (AT91RM9200, AT91SAM9,
SAM9X60) has been enabled such that sam9x SoCs to be able to boot.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Those targets have already enabled some other LED triggers, so enabling
a few more won't be a big problem.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.
This increases uncompressed kernel size by about 100 bytes on ath79/generic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The at91 target sets
FEATURES:=usb usbgadget ...
in the target Makefile, which sets CONFIG_USB_SUPPORT=y in the
.config file for both subtargets.
However, when building with all kmods, the build fails with the
following error message:
ERROR: module [...]/drivers/bluetooth/btusb.ko is missing.
It appears that only a part of the bluetooth files are compiled.
The package depends @USB_SUPPORT.
This can be easily healed by adding CONFIG_USB_SUPPORT=y to the
sam9x subtarget configuration. Before the 4.14->5.4 bump, the
same was also set in the target's config-4.14 file along with
several other USB config options that are not reimplemented.
Still, it remains a mystery to me why setting the same symbol
via target kernel config creates a different result than the
feature setting the same symbol in target-metadata.pl.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This introduces the vendor_model scheme to this target in order to
harmonize device names within the target and with the rest of
OpenWrt. In addition, custom board names are dropped in favor
of the generic script which takes the compatible.
Use the SUPPORTED_DEVICES variable to store the compatible where it
deviates from the device name, so we can use it in build recipes.
While at it, harmonize a few indents as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Changing dtb file path since the dtb files are build in KDIR folder
with image- prefix.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
[remove commented lines]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move patches to 5.4, put config only in subtarget directories.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
[refresh patches, add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This files have been emptied during subtarget consolidation, but
not removed. Remove them now.
Fixes: aff084adf3 ("at91: Merge SAMA5 subtargets")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses DEFAULT := n on a bunch of devices that previously were
"disabled" by commenting out TARGET_DEVICES. This will allow to
build them without having to modify the code, but they will not
be selected for default build or buildbots.
The change is applied to all devices that are not "broken", but suffer
from image site limitations or similar, or have been added in the past
but never confirmed to run on the device properly:
at91: at91-q5xr5:
kernel image too big
31aeae0774 ("at91: do not build image for at91-q5xr5")
bcm47xx: asus-rt-ac66u:
disabled since it was added in 2015
69aefc771f ("brcm47xx: build images for Asus devices")
bcm47xx: netgear-wndr3400-vcna, netgear-wnr3500u, netgear-wnr3500-v2-vc
added disabled in 2012, but never confirmed to work on devices
5dec9dd3b2 ("brcm47xx: add code to generate images for some netgear
devices")
bcm53xx: netgear-r8500
added disabled: "start working on Netgear R8500"
3b76c7cf0b ("bcm53xx: start working on Netgear R8500")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.
This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.
For sunxi, this includes a trivial rename of the subtarget image
Makefiles.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This replaces deprecated backticks by more versatile $(...) syntax.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
check for sama5d4_xplained device while copying at91bootstrap binary
to sdcard image.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
remove at91-sdcard build command from Makefile as this is moved to
respective subtarget Makefile.
Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
This removes some settings which are normally set by the generic
configuration and should not be changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
The configuration of the sama5d4 subtarget was used as the default
configuration and then the subtarget configurations were adapted.
The resulting kernel configuration without any extra modules selected is
still the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
Some targets deactivated CONFIG_SYN_COOKIES, for unknown reasons, use
the default setting from the generic configuration which activates
CONFIG_SYN_COOKIES.
This should prevent SYN flooding.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reduces the needed modifications to the mainline Linux kernel and
also makes the regmap package work with an out of tree kernel which
does not have these modifications.
The regmap-core is only added when it is really build as a module.
The regmap-core is normally bool so it cannot be built as a module in an
unmodified kernel. When it is selected by on other kernel module it will
always be selected as build in and it also does not show up in
$(LINUX_DIR)/modules.builtin as it is not supposed to be a kernel module.
When it is not in $(LINUX_DIR)/modules.builtin the build system expects
it to be built as a .ko file.
Just check if the module is really there and only add it in that case.
This splits the regmap package into multiple packages, one for each bus type.
This way only the bus maps which are really needed have to be added.
This also splits the I2C, SPI and MMIO regmap into separate packages to not
require all these subsystems to build them, on an unmodified upstream kernel
this also causes problems in some situations.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
CONFIG_COMPAT_BRK disables the heap randomization which is only needed
for very old and ancient user space applications, I am not aware that we
run any of these, just deactivate this option for these targets to allow
heap randomization.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
>From the Documentation/devicetree/bindings/leds/common.txt:
- default-state : The initial state of the LED. Valid values are "on", "off",
and "keep". If the LED is already on or off and the default-state property is
set the to same value, then no glitch should be produced where the LED
momentarily turns off (or on). The "keep" setting will keep the LED at
whatever its current state is, without producing a glitch. The default is
off if this property is not present.
So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Compaction is the only memory management component to form high order (larger
physically contiguous) memory blocks reliably. The page allocator relies on
compaction heavily and the lack of the feature can lead to unexpected OOM
killer invocations for high order memory requests. You shouldn't disable this
option unless there really is a strong reason for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The kernel image of the at91-q5xr5 is getting too bing now and this is
breaking the build. Remove the image for the at91-q5xr5 from the build
to at least build images for the other devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a new config option to allow to select the default compile
optimization level for the kernel.
Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.
Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.
Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.
Exceptions to the above are:
- lantiq, where the optimization for size is only required for the
xway_legacy subtarget but was set for the whole target
- mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
plenty of space and an optimization for size doesn't make much sense
- rb532, which has 128MByte flash
Signed-off-by: Mathias Kresin <dev@kresin.me>
These options are handled by generic configuration
Targets that need these options should select KERNEL_DEVMEM
and/or KERNEL_DEVKMEM options on OpenWRT's config
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Refreshed all patches
Added new ARM64 symbol: ARM64_ERRATUM_1024718
Compile-tested on: ar71xx
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Drop the "-x lzo" compression type override from MKUBIFS_OPTS since we
do not support it in mkfs.ubifs. Attempting to use LZO compression results
in "Error: bad compressor name".
The build system also appends an explicit "--compr=zlib" to the mkfs command
line, turning the "-x" flag into a no-op anyway.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The subtarget configurations contained a lot of reduntant symbols, arbitrary
overrides and symbols set to =m.
Remove most of these redundant settings to shrink the subtarget configurations
to a manageable size.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes the following error spotted by the buildbot:
Package kmod-fs-squashfs is missing dependencies for the following libraries:
xz_dec.ko
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
copying at91bootstrap and uboot binaries to sdcard image is done
based on device name instead of dts name and this avoids creating
multiple u-boot and at91bootstrap binaries.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
sama5d2 & samad4 have neon feature and sama5d3 does not have neon
feature due to which sama5d3 boot fails with error message Kernel
panic - not syncing: Attempted to kill init! exitcode=0x00000004.
removing neon & VFPv4 support to fix this
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
when external kernel is selected from menuconfig, device wb50n is not
avaliable and build fails. As a fix adding checks for external kernel.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
The current image build code has a number of race conditions and interface
contract violations in the custom image build steps:
- Build/install-zImage, solely used by at91, relies on $(PROFILE_SANITIZED)
which is not available when building with CONFIG_TARGET_MULTI_PROFILE
- Build/at91-sdcard, which may run concurrently, creates scratch files at
fixed locations and manipulates target files directly which can lead
to file corruption and other unexpected failures
Rename the install-zImage macro to at91-install-zImage and move it to the
at91 image Makefile since this target is the sole user. Also utilize "$@"
as output file name and switch the usage of $(PROFILE_SANITIZED) to
$(DEVICE_NAME) in order to fix naming under multi profile builds.
Fix the at91-sdcard macro to construct scratch file paths relative to "$@",
which is guaranteed to be unique and store the final artifact output in "$@"
as well, instead of inside $(BIN_DIR). The generic image build code takes
care of moving a build steps "$@" output to the final destination in a
concurrency-safe manner.
Finally remove the broken install-zImage from the generic image-commands
Makefile.
Fixes: d7a679a036 ("at91: Install zImage.")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Without this patch one sdcard image with the following name is created
for all devices:
openwrt-at91-sama5--sdcard.img.gz
This makes the build system create device specific versions like:
openwrt-at91-sama5-at91-sama5d2_xplained-sdcard.img.gz
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This activates neon and VFPv4 support for this target. The CPU support
these feature so also use them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The build system took the DTB_SIZE definition from Default and not from
production-dtb under some conditions. Move the size definitions to
Default now as it is only used in production-dtb anyway.
Thanks Mathias Kresin for helping me with this.
Fixes: c2f052acae ("at91: convert boards to generic build target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This module from Laird includes the following:
- CPU Atmel SoC SAMA5D31
- Wifi QCA6004
- Bluetooth CSR8811
- RAM 64MB LPDDR
- FLASH 128MB
The flash is a dual image layout, kernel a/b, rootfs a/b, and a user
partition.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
This module from Laird includes the following:
- CPU Atmel SoC ARM926EJS
- Wifi AR6003
- Bluetooth CSR8510
- RAM 64MB LPDDR
- FLASH 128MB
The flash is a dual image layout, kernel a/b, rootfs a/b, and a user
partition.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Instead of applying global defaults based on selected board, transition
to using a per board setting for UBIFS and UBINIZE.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
The platform generates squashfs images in a UBI block but misses the
kernel module to be able to mount the block.
DMA is also enabled to allow systems which include them in the DTS to
use it.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Add ext4 filesystem for creating sdcard image with ext4 rootfs and
removing ext2 as it superset of ext4.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Enabled SDHCI for sama5 in kernel default config and this is needed
to mount sdcard rootfs partition during boot.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D4 with target device as at91-sama5d4_xplained
in SAMA5 subtarget and build images for SAMA5D4 Xplained board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D2 with target device as at91-sama5d2_xplained
in SAMA5 subtarget and build images for SAMA5D2 Xplained board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Renaming at91 subtarget sama5d3 to sama5 and using at91-sama5d3_xplained
as a target device in sama5 subtarget.This will enable to add other
sama5d2 & sama5d4 target devices in sama5 subtraget.This will avoid
code duplication when sama5d2 & sama5d4 added as different subtarget.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Evaluation boards are left in component form to ease flashing
using vendor tooling and instructions. These boards also do
not include the EOF marker in the UBIFS as the bootloaders
are recent and easily upgradeable.
The end product boards use factory.bin images based on the
dts layout and include EOF markers as bootloader UBI support
is not determined.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
