Include a patch[1] under review to fix the modpost error due to
upstream changes:
...
ERROR: modpost: "cifs_arc4_crypt" [fs/ksmbd/ksmbd.ko] undefined!
ERROR: modpost: "cifs_arc4_setkey" [fs/ksmbd/ksmbd.ko] undefined!
scripts/Makefile.modpost:133: recipe for target 'modules-only.symvers' failed
1. https://lore.kernel.org/all/20231227102605.4766-2-linkinjeon@kernel.org/
Signed-off-by: John Audia <therealgraysky@proton.me>
The default strength is not enough to provide stable connection
under 3.3v LDO voltage.
Fixes: 32d5921b8b ("rockchip: add Orange Pi R1 Plus LTS support")
Fixes: #13117Fixes: #13759
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
`ok` status is obsolete and thus `okay` should be used instead:
spi@78b9000: status:0: 'ok' is not one of ['okay', 'disabled', 'reserved']
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Flash: 16MB SPI NOR flash (Macronix MX25L12805D)
Based on the manufactured datasheet this chip is capable of 50MHz.
We dont enable fast-read as mt7621 are only capable of 44mhz in a read state.
Tested on this unit without any issues.
Signed-off-by: David Bentham <db260179@gmail.com>
The rt305x series SOC have two UART devices,
and the one at bus address 0x500 is disabled by default.
Some boards do not even have a pinout for the first one,
so use the same one that the kernel uses at 0xc00 instead.
This allows the lzma-loader printing to be visible
alongside the kernel log in the same console.
Tested-by: Lech Perczak <lech.perczak@gmail.com> # zte,mf283plus
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Before this was reworked, in the file for mt7621 subtarget
(target/linux/ramips/image/lzma-loader/src/board-mt7621.c)
the "Transmitter shift register empty" bit TEMT was used instead of
the "Transmitter holding register empty" bit THRE,
but after the rework, this value was labeled as the THRE bit instead.
Functionally there is no difference, but this is confusing to read,
as it suggests that the subtargets have different bits for the same
register in UART when in reality they are exactly the same.
One can use either bit, or both, at user's descretion
in order to determine whether the UART TX buffer is ready.
The generic kernel early-printk uses both,
(arch/mips/kernel/early_printk_8250.c)
while the ralink-specific early-printk uses only THRE,
(arch/mips/ralink/early_printk.c).
Define both bits and rewrite macros for readability,
keep the same values, as changing which to use should be tested first.
Ref: c31319b66 ("ramips: lzma-loader: Refactor loader")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The native bus address for UART was entered for rt305x UART_BASE,
but the bootloaders have memory space remapped with the same
virtual memory map the kernel uses for program addressing at boot time.
In UBoot, the remapped address is often defined as TEXT_BASE.
In the kernel, for rt305x this remapped address is RT305X_SYSC_BASE.
(arch/mips/include/asm/mach-ralink/rt305x.h)
Because the ralink I/O busses begin at a low address of 0x10000000,
they are remapped using KSEG0 or KSEG1, which for all 32-bit MIPS SOCs
(arch/mips/include/asm/addrspace.h)
are offsets of 0x80000000 and 0xa0000000 respectively.
This is consistent with the other UART_BASE macros here
and with MIPS memory map documentation.
Before the recent rework of the lzma-loader for ramips,
the original board-$(PLATFORM).c files also did not
use KSEG1ADDR for UART_BASE despite being defined,
which made this mistake easier to occur.
Fix this by defining KSEG1ADDR again and actually use it.
Copy and paste from the kernel's macros for consistency.
Link: https://training.mips.com/basic_mips/PDF/Memory_Map.pdf
Fixes: c31319b66 ("ramips: lzma-loader: Refactor loader")
Reported-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The ESW core needs to be reset together with FE core, so after the
relevant reset controller lines are moved under FE, drop rst_esw and all
related code, which would not execute anyway, because rst_esw would be
NULL. While at that, ensure that if reset line for EPHY cannot be
claimed, a proper error message is reported.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Co-developed-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Split out of the bigger commit, provide commit mesage, refactor error
handling]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Failing to do so will cause the DMA engine to not initialize properly
and fail to forward packets between them, and in some cases will cause
spurious transmission with size exceeding allowed packet size, causing a
kernel panic.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Provide commit description, split into logical changes]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Failing to do so will cause the DMA engine to not initialize properly
and fail to forward packets between them, and in some cases will cause
spurious transmission with size exceeding allowed packet size, causing a
kernel panic.
This is behaviour of downstream driver as well, however I
haven't observed bug reports about this SoC in the wild, so this
commit's purpose is to align this chip with all other SoC's - MT7620
were already using this arrangement.
Fixes: #9284
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Failing to do so will cause the DMA engine to not initialize properly
and fail to forward packets between them, and in some cases will cause
spurious transmission with size exceeding allowed packet size, causing a
kernel panic.
This is behaviour of downstream driver as well, however I
haven't observed bug reports about this SoC in the wild, so this
commit's purpose is to align this chip with all other SoC's - MT7620
were already using this arrangement.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Failing to do so will cause the DMA engine to not initialize properly
and fail to forward packets between them, and in some cases will cause
spurious transmission with size exceeding allowed packet size, causing a
kernel panic.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Provide commit description, split into logical changes]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Enabling the FE core too early causes the system to hang during boot
uncondtionally, after the reset is released. Increate it to 1-1.2ms
range.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Split previous commit, provide rationale]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Use devm_reset_control_array_get_exclusive to register multiple
reset lines in FE driver. This is required to reattach ESW reset to FE
driver again, based on device tree bindings.
While at that, remove unused fe_priv.rst_ppe field, and add error
message if getting the reset fails.
Fixes: 60fadae62b ("ramips: ethernet: ralink: move reset of the esw into the esw instead of fe")
Co-developed-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[Split out of the bigger commit, provide commit mesage, refactor error
handling]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 2 LEDs (Status and Internet, both can be either orange or white)
- 2 buttons (WPS and Reset)
Compared to M32, the R32 has the following differences:
- 4 LAN ports instead of 2
- The recory image starts with DLK6E6015001 instaed of DLK6E6010001
- Individual LEDs for power and internet
- MAC address is stored at another offset in the ODM partition
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
- The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
- The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
- OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Router Asus TUF AX6000 have second MaxLinear GPY211 PHY controller for 2.5Gb LAN port.
The 5'th LAN port have inverted status of the LED.
Based on the commit from main branch 90fbec8 we could set proper status of the LED.
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
The upper 16 bits of the 32 bit value encode the SoC model in BCD
notation (for example 0x83806800 on a Netgear GS108Tv3 with an
RTL8380M), so it makes more sense to output the value in hex notation
than in decimal notation.
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
(based on support for ASUS RT-AX59U by liushiyou006)
SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Upgrade from AsusWRT to OpenWRT using UART
Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.
Connect the PC with TFTP server to the RT-AX59U.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.
Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax59u.bin
$ bootm 0x46000000
Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Upgrade from AsusWRT to OpenWRT using WebUI
Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq
Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file
Wait for OpenWRT to boot (192.168.1.1).
Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command
MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.
: Stock : OpenWrt
WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
WLAN 2g (2) : : CA:xx:xx:0D:xx:D4
WLAN 2g (3) : : CE:xx:xx:0D:xx:D4
WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
WLAN 5g (2) : : CE:xx:xx:1D:xx:D5
WLAN 5g (3) : : C2:xx:xx:1D:xx:D5
WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
WLAN 2g (2) : : 0A:xx:xx:76:xx:BE
WLAN 2g (3) : : 0E:xx:xx:76:xx:BE
WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
WLAN 5g (2) : : 0E:xx:xx:76:xx:BF
WLAN 5g (3) : : 02:xx:xx:76:xx:BF
Signed-off-by: Xavier Franquet <xavier@franquet.es>
Use order described as preferred in DTS Coding Style:
1. Sort bus nodes by unit address
2. Use alpha-numerical order for the rest
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Increasing the receive window size improves throughout on higher-latency
links such as WAN connections. The current default of 24KB caps out at
around 500 KB/s.
Increasing the receive buffer to 256KB increases the throughput to at
least 11 MB/s.
Signed-off-by: David Bauer <mail@david-bauer.net>
Make the node name match the actual memory address.
Fixes: 57d7382cb1 ("mpc85xx: increase available RAM on Extreme Networks WS-AP3825i")
Signed-off-by: David Bauer <mail@david-bauer.net>
Setting up usb gadgets using g_* kernel modules are considered a
legacy approach, but the usb_gadget configfs is a bit annoying
to use directly.
The usb_gadget configfs works by creating magic directories
and writing to magic files under /sys/kernel/config/usbgadget.
This new package is an init script to setup usb_gadget configfs
using uci. In the config file, gadget/configuration/function
sections create corresponding directories. UCI options are magic
files available in the configfs and strings/0x409 directories,
grabbed with a 'find' command. UDC option in gadget writes
the UDC file under the 'gadget' directory to attach the
generated gadget config.
It's also possible to apply pre-made config templates under
/usr/share/usbgadget. The templates use the same UCI config
format, with the 'gadget' entry named 'g1'. Currently, there
are templates for CDC-ACM and CDC-NCM gadgets written based
on existing g_*.ko module code.
Certain SBCs come with only a USB device port (e.g. Raspberry Pi
Zero). With this script, it's now possible to perform initial
setup on them by adding a default NCM gadget.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Allow "postinst" scripts to perform extra actions after applying all
kind of fixups implemented using uci-defaults.
This is needed e.g. by uhttpd-mod-ubus which after installation in a
running systems needs to:
1. Update uhttpd config using its uci-defaults script
2. Reload uhttpd
While this approach makes sense there is a risk it'll blow up some
corner case postinst usages. There is only 1 way to find out.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
* Revert the switch_lan_bmp and switch_wan_bmp to match the values from
the original device support DTS
* Add specific malibu_first_phy_addr, as it differs from default for
this device
Fixes: #14234
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Samir Ibradžić <sibradzic@gmail.com> # Buffalo WXR-6000AX12P
Signed-off-by: Samir Ibradžić <sibradzic@gmail.com>
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Unielec u7621-01.
According to the bootlog, MT7612E (5 GHz) is connected to pcie2, and
MT7603E (2 GHz) is connected to pcie1:
[ 1.294844] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[ 1.308635] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 1.318277] mt7621-pci 1e140000.pcie: PCIE2 enabled
Also correct the led activity for the MT7603e - not used on the MT7612e
Signed-off-by: David Bentham <db260179@gmail.com>
This node is useless because MT7621 uses the generic mips systick
driver instead of the ralink systick driver.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add support for wireless offload package in default configuration for
-Cudy WR3000
-Confiabits MT7981
For some reason those ware missing. I confirm this work for my Cudy WR3000
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Kernel 5.15 introduced a significant change to spi-nor subsystem [1],
which would the SPI-NOR core to no longer unprotect the Flash chips if
their protection bits are non-volatile, which is the case for MX25L6405D
and MX25L12805D, used in Ubiquiti XW and WA lines of devices [2].
However, their bootloader forcibly enables this protection before
continuing to boot, making the kernel not unprotect the flash upon boot,
causing JFFS2 to be unable write to the filesystem. Because sysupgrade
seems to unlock the flash explicitly, the upgrade will work, but the
system will be unable to save configrationm showing the following symptom
in the kernel log:
[ 86.168016] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 86.192344] jffs2_build_filesystem(): unlocking the mtd device...
[ 86.192443] done.
[ 86.200669] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 86.220646] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001e0000
[ 86.292388] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001d0000
[ 86.324867] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001c0000
[ 86.355316] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001b0000
[ 86.402855] jffs2: Newly-erased block contained word 0x19852003 at offset 0x001a0000
Disable the write protection unconditionally for ath79/generic subtarget,
so the XW and WA devices can function again. However, this is only a
stopgap solution - it probably should be investigated if there is a way
to selectively unlock the area used by rootfs_data - but given the lock
granularity, this seems unlikely.
With this patch in place, rootfs_data partition on my Nanostation Loco
M5 XW is writable again.
Fixes: #12882Fixes: #13750
Fixes: 579703f38c ("ath79: switch to 5.15 as default kernel")
Link: http://www.infradead.org/pipermail/linux-mtd/2020-October/082805.html
Link: https://forum.openwrt.org/t/powerbeam-m5-xw-configuration-loss-after-reboot/141925
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Fixes: openwrt#12420
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
The MAC embedded in rtl93xx switch SoCs needs different mac mode bits set
to support 10BaseT and 100BaseT link modes. Set them accordingly.
This change has been tested on a ZyXEL XGS1250-12.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This reverts commit 3004c20614.
The commit added the needed packages for the new target
to the generic x86_64 image. This results into unwanted
modules and firmware files for other x86 devices.
Additionally, there is the following error message
while booting the image on other x86 devices:
[ 8.531720] kmodloader: 1 module could not be probed
[ 8.532613] kmodloader: - leds-mlxcpld - 0
For now, the needed packages will have to be selected
manually while configuring the image.
Signed-off-by: Til Kaiser <til.kaiser@gmx.de>
