Commit Graph

57936 Commits

Author SHA1 Message Date
Pavel Pernička
dac0a133cf ath79: DTS improvement for buzzer on RB951G-2HnD
Mikrotik RB951 router has a buzzer on the board, which makes annoying noises
due to the interference caused by PoE input or Wifi transmission
when no GPIO pin state is set.
I added buzzer node to device's DTS in order to set deault level to 1
and to provide easier access for it.

Signed-off-by: Pavel Pernička <pernicka.pa@gmail.com>
2023-07-01 15:51:26 +02:00
Mathew McBride
8e7ba6fbae layerscape: remove Traverse LS1043 boards
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.

Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).

It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-07-01 15:47:08 +02:00
Chukun Pan
e78d1a06c8 mediatek: filogic: add H3C Magic NX30 Pro support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: W25N01GVZEIG 128MB
  RAM: NT5CB128M16JR-FL 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, WPS
  Power: DC 12V 1A

Flash instructions:
  1. PC run command: "telnet 192.168.124.1 99"
     Username: H3C, password is the web login
     password of the router.
  2. Download preloader.bin and bl31-uboot.fip
  3. PC run command: "python3 -m http.server 80"
  4. Download files in the telnet window:
     "wget http://192.168.124.xx/xxx.bin"
     Replace xx with your PC's IP and
     the preloader.bin and bl31-uboot.fip.
  5. Flushing openwrt's uboot:
     "mtd write xxx-preloader.bin BL2"
     "mtd write xxx-bl31-uboot.fip FIP"
  6. Connect to the router via the Lan port,
     set a static ip of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  7. Download initramfs image, reboot router,
     waiting for tftp recovery to complete.
  8. After openwrt boots up, perform sysupgrade.

Note:
  1. The u-boot-env partition on mtd is empty,
     OEM stores their env on ubi:u-boot-env.
  2. Back up all mtd partitions before flashing.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-07-01 15:13:08 +02:00
Chukun Pan
437e79ad6d uboot-mediatek: add H3C Magic NX30 Pro support
The OEM uboot limit brush into 3rd-party firmware.
So add a custom uboot build to support openwrt.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-07-01 15:13:08 +02:00
Wenli Looi
73de41898f mediatek: add support for Netgear EX6250v2 series
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.

Related: https://github.com/openwrt/openwrt/pull/5084

For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.

Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
  boot, then hold the reset button for 10 seconds. This is needed
  because sysupgrade in the stock firmware will attempt to preserve its
  configuration using sysupgrade.tgz.
  See https://github.com/openwrt/openwrt/pull/4182

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00
Wenli Looi
32ea8a9a7e ramips: add support for Netgear EAX12 series
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.

Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)

All LEDs and buttons appear to work without state_default.

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz

* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
  DTS file for this device.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00
Wenli Looi
0a1ebccc87 image: add additional fields to Netgear encrypted image
These fields are used for EAX12 and EX6250v2 series, and perhaps other
devices. Compatibility is preserved with the WAX202 and WAX206.

In addition, adds the related vars to DEVICE_VARS so that the variables
work correctly with multiple devices.

References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz

* tools/imgencoder/src/gj_enc.c
  Contains code that generates the encrypted image.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00
Robert Marko
b20be1e41e kernel: qca-nss-dp: port FDB roaming fix
In the recent NSS-DP update FDB roaming fix we had was removed as in
testing no issue were reported, but after it was merged the old duplicate
MAC issue reappeared so lets port the previous FDB fix to work with newer
NSS-DP.

Fixes: 4ee444b5da ("kernel: qca-nss-dp: update to 12.4.5.r1")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-07-01 14:22:37 +02:00
Zoltan HERPAI
f8428f040c mxs: add testing kernel 6.1
Runtime-tested on Olinuxino Maxi.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-07-01 12:54:30 +02:00
Hauke Mehrtens
2486841c1b rpcd: update to latest git HEAD
c07ab2f iwinfo: update byte counter to 64bit

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-07-01 12:14:07 +02:00
Hauke Mehrtens
a226153067 iwinfo: update to latest git HEAD
d1f07cf devices: add device id for Atheros AR9287 and AR9380
65ea345 nl80211: constify a few arrays
ca79f64 lib: report byte counters as 64 bit values

This contains an ABI change, increase the ABI version too.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-07-01 12:10:41 +02:00
Hauke Mehrtens
513bcfdf78 libnl-tiny: update to latest git HEAD
d433990 Make struct nla_policy and struct nlattr const

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-07-01 12:07:05 +02:00
Mathew McBride
fff6833d4c linux-firmware: ibt-firmware: install sfi/ddc files for AX210 card
When using an Intel AX210 card, the Bluetooth hci interface failed
to start due to a missing "ibt-0041-0041.sfi" file.

Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-0041-0041.sfi (-2)

A device specific configuration file (DDC) is also required:
Bluetooth: hci0: Found device firmware: intel/ibt-0041-0041.sfi
Bluetooth: hci0: Waiting for firmware download to complete
...
Bluetooth: hci0: Found Intel DDC parameters: intel/ibt-0041-0041.ddc
Bluetooth: hci0: Applying Intel DDC parameters completed
Bluetooth: hci0: Firmware timestamp 2023.13 buildtype 1 build 62562

Fixes: #8558
Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-07-01 11:57:33 +02:00
Robert Marko
39b2251cd9 treewide: remove CONFIG_FRAME_WARN from kernel configs
CONFIG_FRAME_WARN is set dynamically, so there is no need for it to be set
in target kernel configs, so lets remove it from all configs.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-07-01 11:53:21 +02:00
Robert Marko
7a9a4168bb generic: filter out CONFIG_FRAME_WARN
CONFIG_FRAME_WARN value is set by config/Config-kernel.in based on the
target type dynamically since commit:
16a2051 ("kernel: Set CONFIG_FRAME_WARN depending on target").

However, CONFIG_FRAME_WARN was not set to get filtered out so it ended up
in multiple target configs during refreshes.
So, lets filter out CONFIG_FRAME_WARN as its set dynamically to prevent it
ending up in more target configs.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-07-01 11:52:07 +02:00
John Audia
42cb0f0f26 kernel: bump 5.15 to 5.15.119
Build system: x86_64
Build-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3
Run-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-07-01 11:42:11 +02:00
Zoltan HERPAI
a0ae7a50e0 mxs: rework image generation
Migrate to "new" image generation method. Device profiles will be generated
based on image/Makefile instead of profiles/ , which will also allow to
automatically build images for all supported devices via buildbot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-06-30 19:24:52 +02:00
Felix Fietkau
dc38199b96 ramips/mt7621: disable the cpufreq driver
It causes a noticeable performance decrease

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-06-30 14:46:49 +02:00
Felix Fietkau
c8963580aa mac80211: fix mesh fast tx cache issues
Split the cache by tx type in order to avoid packet drop issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-06-30 13:18:55 +02:00
Felix Fietkau
81f667513a netifd: update to the latest version
493e1589bc8b bridge: fix coverity false positive report
03a619947717 bridge: add support for configuring extra vlans for the bridge itself
4bea6d21a9ab wireless: fix changing reconf/serialize options in configuration
255b4d5c472e wireless: fix handling config reload with reconf=1
1ab992a74b43 wireless: fix another reconf issue

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-06-29 12:54:38 +02:00
Felix Fietkau
9419a50242 ucode: update to the latest version
9986b839595d ci: unbreak failing builds by using fixed gh-actions-openwrt-ci-sdk
77c961e20eda ci: fix broken imx6-generic SDK build
86107a647cb0 ci: cancel concurrent builds
ed543d8bf481 ci: update the workflows
11d5f8840002 Merge pull request #151 from ynezz/ynezz/unbreak-ci
b934ce815ff2 program: fix memory leak in read_sourceinfo
b0baf043e64c Merge pull request #152 from Ansuel/fix-memory-leak
740e2501fdca main: add user specified library search paths before default path
15f1a669e8e2 struct: remove state->len
29edb011caf1 ubus: add support for strings containing null bytes
2b4346bfdc67 vm: clear vm->alloc_refs in uc_gc_common
b213bd120d55 Merge pull request #150 from nbd168/misc-improvements
66520ebe27ae vm: immediately release arguments on calls with invalid spreads
07cc72a77e3b README.md: fix debian dependencies
d048ea88fe71 compiler: fix memory leak in uc_compiler_compile_import on early exit
7b7e22dcdf02 Merge pull request #155 from luizluca/luizluca-patch-1
d656d150905e types: implement ucv_object_sort()
d72eebeb168b lib: support object ordering in `uc_sort()`
ed1f0133c870 nl80211: add constants for iftypes
3ffb046c59a6 Merge pull request #156 from nbd168/nl80211-iftypes
c7d84aae0969 Merge pull request #153 from jow-/lib-sort-object-support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-06-29 12:54:34 +02:00
Felix Fietkau
01885bc6a3 mt76: update to the latest version
2c9c8ffe9d8c wifi: mt76: mt7615: fix possible race in mt7615_mac_sta_poll
3365c80f4202 wifi: mt76: connac: fix stats->tx_bytes calculation
b69d82130b47 wifi: mt76: connac: do not check WED status for non-mmio devices
1f9cd65b55d7 wifi: mt76: mt7921e: fix probe timeout after reboot
42dace9ce247 wifi: mt76: mt7921: Fix use-after-free in fw features query.
540adbb38205 wifi: mt76: mt7921: add Netgear AXE3000 (A8000) support
150e2d0ffc0c wifi: mt76: mt7996: fix possible NULL pointer dereference in mt7996_mac_write_txwi()
5b7519be2bf6 wifi: mt76: mt7996: fix endianness of MT_TXD6_TX_RATE
40f6e433f747 wifi: mt76: mt76x02: remove WEP support
84ea1a24f5b5 mt76: mt7921: don't assume adequate headroom for SDIO headers
5c28e17f8c78 wifi: mt76: mt7996: fix header translation logic
2386cec860fa wifi: mt76: mt7996: enable BSS_CHANGED_MU_GROUPS support
748d4a2bfebd wifi: mt76: mt7615: enable BSS_CHANGED_MU_GROUPS support
458ad0af21be wifi: mt76: enable UNII-4 channel 177 support
7fb046011293 wifi: mt76: mt7915: fix background radar event being blocked
d2a77a9954bb wifi: mt76: mt7915: report tx retries/failed counts for non-WED path
f76b102b09ca wifi: mt76: mt7915: rework tx packets counting when WED is active
5637d9e37d9e wifi: mt76: mt7915: rework tx bytes counting when WED is active
34bdc7fcb4c0 wifi: mt76: report non-binding skb tx rate when WED is active
d71aa7b992a3 wifi: mt76: mt7915: drop return in mt7915_sta_statistics
251c363c3087 wifi: mt76: mt7996: drop return in mt7996_sta_statistics
150bb95cb153 wifi: mt76: mt7921: do not support one stream on secondary antenna only
d480c3281f21 wifi: mt76: mt7921: remove macro duplication in regs.h
18b1027e5b6e wifi: mt76: mt7915: move mib_stats structure in mt76.h
25ec4b91020e wifi: mt76: mt7996: rely on mib_stats shared definition
6541afa88b3b wifi: mt76: mt7921: rely on mib_stats shared definition
eeb60eb9a5a0 wifi: mt76: mt7915: add support for MT7981 [sync with upstream]
d5b7e6a3d735 wifi: mt76: mt7921e: report tx retries/failed counts in tx free event
f0f19cea6646 wifi: mt76: mt7921: fix skb leak by txs missing in AMSDU
edd8a830f6e3 wifi: mt76: add tx_nss histogram to ethtool stats
e48235308b3e wifi: mt76: mt7915: accumulate mu-mimo ofdma muru stats
a729242363d9 wifi: mt76: mt7921: fix non-PSC channel scan fail
8d52436ee0cd wifi: mt76: mt7921: Support temp sensor
d152c8688c14 wifi: mt76: mt7915: disable WFDMA Tx/Rx during SER recovery
d07785c344ac wifi: mt76: mt7996: disable WFDMA Tx/Rx during SER recovery
2a19784137f9 wifi: mt76: mt7921: make mt7921_mac_sta_poll static
da8e33a15e71 wifi: mt76: mt7915: fix command timeout in AP stop period
cc58d5c4a9c9 mt76: mt7996: rely on mt76_sta_stats in mt76_wcid
98a37c82a373 wifi: mt76: mt7921: get rid of MT7921_RESET_TIMEOUT marco
ece724cf562b wifi: mt76: mt7996: move radio ctrl commands to proper functions
527cbbc5ede7 wifi: mt76: connac: add support for dsp firmware download
44e323340637 wifi: mt76: mt7996: fix bss wlan_idx when sending bss_info command
63f0053df07a wifi: mt76: mt7996: enable VHT extended NSS BW feature
e1bb4ef7b2bb wifi: mt76: connac: add support to set ifs time by mcu command
080ca19cc686 wifi: mt76: mt7996: use correct phy for background radar event
2c163f1812a3 wifi: mt76: mt7996: fix WA event ring size
b511a437ace4 wifi: mt76: mt7996: add muru support
ece67c98dc1c wifi: mt76: mt7996: increase tx token size
7c2515d85117 wifi: mt76: mt7921e: fix init command fail with enabled device
30706095c566 wifi: mt76: mt7915: move sta_poll_list and sta_poll_lock in mt76_dev
b06ed10ee271 wifi: mt76: mt7603: rely on shared sta_poll_list and sta_poll_lock
b59bdae339de wifi: mt76: mt7615: rely on shared sta_poll_list and sta_poll_lock
6da2e0e4ef54 wifi: mt76: mt7996: rely on shared sta_poll_list and sta_poll_lock
b19d3ad88e8b wifi: mt76: mt7921: rely on shared sta_poll_list and sta_poll_lock
595b033275a3 wifi: mt76: mt7915: move poll_list in mt76_wcid
16fcad171849 wifi: mt76: mt7603: rely on shared poll_list field
e19f84091d2e wifi: mt76: mt7615: rely on shared poll_list field
b87e4dad1e84 wifi: mt76: mt7996: rely on shared poll_list field
6d7950e258d0 wifi: mt76: mt7921: rely on shared poll_list field
f5c5eece5038 wifi: mt76: move ampdu_state in mt76_wcid
7e44467469fe mt76: connac: move more mt7921/mt7915 mac shared code in connac lib
39a70710ddcd wifi: mt76: move rate info in mt76_vif
0dc4326991df wifi: mt76: connac: move connac3 definitions in mt76_connac3_mac.h
29cfabbb4b90 wifi: mt76: connac: add connac3 mac library
d60b401867f4 linux-firmware: update firmware for MT7922 WiFi device
9404601a6c97 linux-firmware: update firmware for MT7922 WiFi device
2f851902d6b1 linux-firmware: update firmware for MT7921 WiFi device
f36b921692b9 Revert "wifi: mt76: mt76x02: remove WEP support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-06-28 15:18:08 +02:00
Martin Schiller
5af7d47cd7 kernel: net: phy: realtek: fix rtl822x_probe on unsupported devices
Calling rtl822x_probe() on phy devices which uses the rtl822x_read_mmd()
and rtl822x_write_mmd() functions makes no sense and the probe ends with
an EOPNOTSUPP error.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2023-06-27 13:56:34 +02:00
Robert Marko
539cb5389d
kernel: qca-nss-dp: simplify compile arguments
Instead of manually passing arguments, lets just switch to using
$(KERNEL_MAKE).

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-06-26 16:17:41 +02:00
Robert Marko
4ee444b5da
kernel: qca-nss-dp: update to 12.4.5.r1
Qualcomm has finally started the preparatory work in order to support
kernel 6.1, so lets make use of that and update NSS-DP 12.4.5.r1 which
allows us to drop almost some of the patches.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-06-26 16:17:41 +02:00
Robert Marko
b45562a69c
kernel: qca-ssdk: update to 12.4.5.r1
Qualcomm has finally started the preparatory work in order to support
kernel 6.1, so lets make use of that and update SSDK 12.4.5.r1 which
allows us to drop almost all of the patches.

Lets also install the forgotten SSDK netlink header.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-06-26 16:17:37 +02:00
Tianling Shen
186976c963 arm-trusted-firmware-rockchip: add m0 gcc toolchain
rk3399 ATF requires arm toolchain to build the m0 pmu driver.
As OpenWrt doesn't ship this toolchain so download the prebuilt one
just like what we did in arm-trusted-firmware-mvebu.

Fixes: 5d1cb52da0 ("arm-trusted-firmware-rockchip: Update to 2.9")

Reported-by: Wurzer Juergen <wurzer.juergen@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-06-25 22:52:15 +02:00
Hauke Mehrtens
3596380987 procd: update to latest git HEAD
122a5e3 Revert "sysupgrade: print errno on failure"
2db8365 system: add RISC-V CPU info

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-06-25 22:48:55 +02:00
Hauke Mehrtens
9d8d65322c rpcd: update to latest git HEAD
31c3907 file: strengthen exec access control

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-06-25 22:48:55 +02:00
Hauke Mehrtens
7a6f6b8126 uhttpd: update to latest git HEAD
34a8a74 uhttpd/file: fix string out of buffer range on uh_defer_script

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-06-25 22:48:55 +02:00
Hauke Mehrtens
03ce5598a0 kernel: phy: motorcomm: Fix compile
Fix compilation on starfive target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-06-25 22:48:55 +02:00
Felix Fietkau
fc08989a32 Revert "mt76: update to the latest version"
This reverts commit 901af27189.
Will be re-applied once crash issues have been figured out and resolved

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-06-25 22:22:53 +02:00
Shiji Yang
285f0668f4 ramips: do not print error log when mdio bus is disabled
The mdio bus is used to control externel switch. In most cases, they are
disabled, which is the normal behavior. Treating this as an error makes
no sense, so we need to change the notification level from error to info.

Fixes: a2acdf9607 ("ramips: mt7620: remove useless GMAC nodes")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-06-25 18:48:29 +02:00
Shiji Yang
4e74777fa8 ramips: backport upstream mt762x PCIe driver error log fixes
These patches silence some mt762x PCIe driver error messeges by removing
the useless debugging codes and replacing incorrectly used 'dev_err()'
with 'dev_info()':

PCI: mt7621: Use dev_info() to log PCIe card detection [1]
mips: pci-mt7620: do not print NFTS register value as error log [2]
mips: pci-mt7620: use dev_info() to log PCIe device detection result [3]

Patch [1] has already been merged into the Linux 6.3 branch. Patches [2] and
[3] have been merged into the "mips-next" tree, and they will be part of the
upcoming Linux 6.5.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v6.4-rc7&id=50233e105a0332ec0f3bc83180c416e6b200471e
[2] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=9f9a035e6156a57d9da062b26d2a48d031744a1e
[3] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=89ec9bbe60b61cc6ae3eddd6d4f43e128f8a88de

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-06-25 18:48:24 +02:00
Alexey Bartenev
ce998cb6e1 ramips: add support for D-Link DIR-806A B1 router
General specification:
SoC Type: MediaTek MT7620A (580MHz)
ROM: 8 MB SPI-NOR (MX25L6406E)
RAM: 64 MB DDR (W9751G6KB-25)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Wireless: 5 GHz (MediaTek MT7610EN): ac/n
Buttons: 2 button (POWER, WPS/RESET)
Bootloader: U-Boot 1.1.3
Power: 12 VDC, 0.5 A

MACs:
| LAN	| [Factory + 0x04] - 2		|
| WLAN 2.4g	| [Factory + 0x04] - 1		|
| WLAN 5g	| [Factory + 0x8004] - 3	|
| WAN	| [Factory + 0x04] - 2		|

OEM easy installation:

1. Use a PC to browse to http://192.168.0.1.
2. Go to the System section and open the Firmware Update section.
3. Under the Local Update at the right, click on the CHOOSE FILE...
4. When a modal window appears, choose the firmware file and click on
 the Open.
5. Next click on the UPDATE FIRMWARE button and upload the firmware image.
Wait for the router to flash and reboot.

OEM installation using the TFTP method (need level converter):

1. Download the latest firmware image.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware
 image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect the PC
 to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address 192.168.0.180
 and subnet mask 255.255.255.0.
5. Connect serial port (57600 8N1) and turn on the router.
6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load
 system code then write to Flash via TFTP.").
7. Press Y key when show "Warning!! Erase Linux in Flash then burn new
 one. Are you sure? (Y/N)"
Input device IP (192.168.0.1) ==:192.168.0.1
Input server IP (192.168.0.180) ==:192.168.0.180
Input Linux Kernel filename () ==:firmware_name
The router should download the firmware via TFTP and complete flashing in
 a few minutes.
After flashing is complete, use the PC to browse to http://192.168.1.1 or
 ssh to proceed with the configuration.

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2023-06-25 16:25:01 +02:00
Mathew McBride
a7bd96c98f layerscape: add patches for SFP support on DPAA2 platforms
This is required for managed operation of the SFP ports on
the Ten64 (LS1088A) and other boards.

The two issues resolved are:
- Validation of 10G SFP link modes fail as Linux did not
  consider the equivalence of modes like XFI, 10GBase-R
- Fix a locking issue that prevented the system rebooting
  when SFP ports were controlled by the SFP driver.

Please note, these patches are replaced by upstream ones
in 6.x, see: commit 61ec9a8154 ("armvirt: add SFP support
patches for NXP Layerscape DPAA2 platforms") in OpenWrt for
the relevant patches.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-06-25 16:02:19 +02:00
Mathew McBride
af0546da34 layerscape: armv8_64b: add Traverse Ten64 NAND variant
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.

See the online manual for more information, including the
flash layout[2].

This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.

We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
2023-06-25 16:02:19 +02:00
Andreas Böhler
f70ee53b08 ipq4019: add support for ZTE MF287+ aka DreiNeo
The ZTE MF287+ is a LTE router used (exclusively?) by the network operator
"3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only
difference is the LTE modem)

Specifications
==============

SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287)
WiFi: 802.11a/b/g/n/ac SoC-integrated

MAC addresses
=============

LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x82000000 openwrt.bin
  bootm 0x82000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m14
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd13 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 14
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.

Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-06-25 15:53:03 +02:00
Andreas Böhler
9ffdaa7fa1 ipq40xx: Enable gpio-restart in kernel configuration
Some ZTE devices require the gpio-restart driver to support restarting the
LTE modem along with OpenWrt

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-06-25 15:53:03 +02:00
Stefan Weil
8d06bc1751 ramips: add Edimax BR-6208AC V2 support
Specifications:
- Device: Edimax BR-6208AC V2
- SoC: MT7620A
- Flash: 16 MiB
- RAM: 64 MiB
- Switch: 1 WAN, 3 LAN (10/100 Mbps)
- WiFi: MT7620 2.4 GHz + MT7610E 5 GHz
- LEDs: 1x POWER (green, not configurable)
        1x Firmware (green, configurable)
        1x Internet (green, configurable)
        1x VPN (green, configurable)
        1x 2.4G (green, not configurable)
        1x 5G (green, not configurable)

Normal installation:
- Upload the sysupgrade image via the default web interface

Installation with U-Boot and TFTP:
- Requires a TFTP server which provides the sysupgrade image
- Requires a connection to the serial port of the device, rate 57600

Signed-off-by: Stefan Weil <sw@weilnetz.de>
2023-06-25 13:58:26 +02:00
Michał Kępień
db02cecd6a ath79: add support for MikroTik RB951G-2HnD
MikroTik RB951G-2HnD is a wireless SOHO router that was previously
supported by the ar71xx target, see commit 7a709573d7 ("ar71xx: add
kernel support for the Mikrotik RB951G board").

Specifications
--------------

  - SoC: Atheros AR9344 (600 MHz)
  - RAM: 128 MB (2x 64 MB)
  - Storage: 128 MB NAND flash (various manufacturers)
  - Ethernet: Atheros AR8327 switch, 5x 10/100/1000 Mbit/s
      - 1x PoE in (port 1, 8-30 V input)
  - Wireless: Atheros AR9340 (802.11b/g/n)
  - USB: 2.0 (1A)
  - 8x LED:
      - 1x power (green, not configurable)
      - 1x user (green, not configurable)
      - 5x GE ports (green, not configurable)
      - 1x wireless (green, not configurable)
  - 1x button (restart)

Unlike on the RB951Ui-2HnD, none of the LEDs on this device seem to be
GPIO-controllable, which was also the case for older OpenWRT versions
that supported this board via a mach file.  The Ethernet port LEDs are
controlled by the switch chip.

See https://mikrotik.com/product/RB951G-2HnD for more details.

Flashing
--------

TFTP boot initramfs image and then perform sysupgrade.  Follow
common MikroTik procedures at https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
2023-06-25 13:18:32 +02:00
Michał Kępień
c6ef417094 ath79: mikrotik: extract common bits for RB951x-2HnD devices
Mikrotik RouterBOARD 951Ui-2HnD and Mikrotik RouterBOARD RB951G-2HnD are
very similar devices.  Extract the DTS bits that are identical for these
two boards to a separate DTSI file.

Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
2023-06-25 13:18:31 +02:00
Luiz Angelo Daros de Luca
e95c772894 ath79: 5.15: fix not exported sym ath79_pll_base
ath79_pll_base was declared as extern but no code exported it.
Anyone including arch/mips/include/asm/mach-ath79/ath79.h and compiled
as a module would break with:

ERROR: modpost: "ath79_pll_base" [drivers/net/ethernet/atheros/ag71xx/ag71xx.ko] undefined!

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2023-06-25 13:05:39 +02:00
Tianling Shen
5d1cb52da0 arm-trusted-firmware-rockchip: Update to 2.9
Switch to standard TF-A build.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-06-25 13:02:58 +02:00
Maximilian Martin
906e2a1b99 ath79: Add support for MOXA AWK-1137C
Device specifications:
======================

* Qualcomm/Atheros AR9344
* 128 MB of RAM
* 16 MB of SPI NOR flash
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4/5 GHz Wi-Fi
* 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* 2x fast ethernet
  - lan1
    + builtin switch port 1
    + used as WAN interface
  - lan2
    + builtin switch port 2
    + used as LAN interface
* 9-30V DC
* external antennas

Flashing instructions:
======================

Log in to https://192.168.127.253/
   Username: admin
   Password: moxa

Open Maintenance > Firmware Upgrade and install the factory image.

Serial console access:
======================

Connect a RS232-USB converter to the maintenance port.
   Pinout: (reset button left) [GND] [NC] [RX] [TX]

Firmware Recovery:
==================

When the WLAN and SYS LEDs are flashing, the device is in recovery mode.

Serial console access is required to proceed with recovery.

Download the original image from MOXA and rename it to 'awk-1137c.rom'.
Set up a TFTP server at 192.168.127.1 and connect to a lan port.

Follow the instructions on the serial console to start the recovery.

Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
2023-06-25 12:59:26 +02:00
Mikhail Zhilkin
e4fe3097ef mediatek: add support for Mercusys MR90X v1
This commit adds support for Mercusys MR90X(EU) v1 router.

Device specification
--------------------
SoC Type:   MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM:        MediaTek MT7986BLA (512MB)
Flash:      SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet:   MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet:   1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g:    MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g:    MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs:       1 orange and 1 green status LEDs, 4 green gpio-controlled
            LEDs on ethernet ports
Button:     1 (Reset)
USB ports:  No
Power:      12 VDC, 2 A
Connector:  Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
            slots contain "seconduboot" (also U-Boot 2022.01-rc4)

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |
    +--- Don't connect

The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.

Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot initramfs-kernel.bin
      bootm
4. Once inside OpenWrt, set / update env variables:
      fw_setenv baudrate 115200
      fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
      fw_setenv fdtcontroladdr 5ffc0e70
      fw_setenv ipaddr 192.168.1.1
      fw_setenv loadaddr 0x46000000
      fw_setenv mtdids "spi-nand0=spi-nand0"
      fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
      fw_setenv netmask 255.255.255.0
      fw_setenv serverip 192.168.1.2
      fw_setenv stderr serial@11002000
      fw_setenv stdin serial@11002000
      fw_setenv stdout serial@11002000
      fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Installation (without UART)
---------------------------
1.  Login as root via SSH (router IP, port 20001, password - your web
    interface password)
2.  Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
    SSH settings from the p.1)
3.  Add a newline after "#!/bin/sh":
       telnetd -l /bin/login.sh
4.  Save "65-iptv" file
5.  Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
    save
6.  Make sure that telnetd is running:
       netstat -ltunp | grep 23
7.  Login via telnet to router IP, port 23 (no username and password are
    required)
8  Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
    router (e.g., using WinSCP and SSH settings from the p.1)
9.  Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
    download and upload the full version of busybox to the router. For
    example, from here:
    https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
    Upload busybox-arm64 to the /tmp dir of the router and run:
    in the telnet shell:
       cd /tmp
       chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
       du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
    (greater than "initramfs-kernel.bin" size):
       ubirmvol /dev/ubi0 -N kernel
       ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
       ./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
    already exists) with the necessary values:
       fw_setenv baudrate 115200
       fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
       fw_setenv fdtcontroladdr 5ffc0e70
       fw_setenv ipaddr 192.168.1.1
       fw_setenv loadaddr 0x46000000
       fw_setenv mtdids "spi-nand0=spi-nand0"
       fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
       fw_setenv netmask 255.255.255.0
       fw_setenv serverip 192.168.1.2
       fw_setenv stderr serial@11002000
       fw_setenv stdin serial@11002000
       fw_setenv stdout serial@11002000
       fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
       reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
       sysupgrade -n /tmp/sysupgrade.bin

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
   upload the OEM firmware

Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot initramfs-kernel.bin
      bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
   etc.)

Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"

ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot   Vol ID: 0|
| Volume Name: kernel  Vol ID: 1|
| Volume Name: rootfs  Vol ID: 2|
+-------------------------------+

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| label   | 00:eb:xx:xx:xx:be | label     |
| LAN     | 00:eb:xx:xx:xx:be | label     |
| WAN     | 00:eb:xx:xx:xx:bf | label+1   |
| WLAN 2g | 00:eb:xx:xx:xx:be | label     |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1   |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-06-25 12:25:22 +02:00
Lech Perczak
9d64cc068f ipq40xx: meraki-mr33, meraki-mr74: disable image generation
After migrating to kernel 5.15, upgrading causes the units to become
soft-bricked, hanging forever at the kernel startup.
Kernel size limitation of 4000000 bytes is suspected here, but this is
not fully confirmed.

Disable the images to protect users from inadvertent bricking of units,
because recovery of those is painful with Cisco's U-boot, until the root
cause is found and fixed.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2023-06-25 12:04:12 +02:00
Stefan Kalscheuer
b308bd50ef kernel: migrate FORCE_MAX_ZONEORDER to ARCH_FORCE_MAX_ORDER for 6.1
The flag FORCE_MAX_ZONEORDER was renamed to ARCH_FORCE_MAX_ORDER in
Kernel 6.1 [1]. Rename the flag in generic Kconfig and remove it from
target configs.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=0192445cb2f7ed1cd7a95a0fc8c7645480baba25

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
2023-06-25 11:26:50 +02:00
Davide Fioravanti
f1136fe1fd bcm53xx: add Wavlink Quantum DAX/WL-WN538A8 as alt name
As already documented in the wiki (https://openwrt.org/toh/wavlink/quantum_dax_wn538a8),
this router is based on the Phicomm K3. Just the flashing method is different

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-06-25 11:05:34 +02:00
Davide Fioravanti
c71dada926 ramips: fix lan leds for Wavlink WL-WN535K1
Previously both lan1 and lan2 leds were wrongly labelled as lan2.
Moreover they were connected to the wrong lan port.
Fixes 8fde82095b ("ramips: add support for Wavlink WL-WN535K1")

Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com>
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-06-25 11:02:04 +02:00