FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0)
and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362
SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the
GPIO reset definitions to each individual board .dts and while at it,
fix the GPIOs for the FRITZ!Box 7362 SL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit 56cd49bdc8)
The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to
establish connection with custom commands specific to ZTE modems.
Two variants of modems were discovered, some identifying themselves
as "ZTE", and others as plain "Marvell", the chipset manufacturer.
The modem itself runs a fork of OpenWrt inside, which root shell can be
accessed via ADB interface.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit e02fb42c53)
Some modems expose ttyACM as their control ports, which have the
"device" symlink pointing one level down in sysfs tree. Try to find
network interfaces for them as well, this is commonly used for modems
exposing ACM + RNDIS or ACM + ECM interface combinations.
Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit ed7957810c)
Some modems expose multiple network interfaces on the same USB device,
causing the connection setup script to fail, because glob matching in
the detection phase causes 'ls' to output more than one interface name
plus their base directories in sysfs. Avoid that by listing the
directories explicitly and then selecting first available interface.
This is the case for some variants of ZTE MF286R built-in modem, which
exposes both RNDIS and CDC-ECM network interfaces, causing the
connection setup to fail.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit b2940bb8b2)
Add ifname property to UCI, which can be used to override the
autodetected interface name in case the detection fails due to having
none or more than one interface exposed by the modem, which is not
explicitly linked to TTY port. This is needed on certain variants of ZTE
MF286R built-in modem, which exposes both RNDIS and CDC-ECM interfaces
on the modem, on which the automatic detection may select the wrong
network interface.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit a67629bbe2)
This is required to support built-in modem of ZTE MF286R, in addition to
other external modems, such as MF831, MF910, MF920, which refuse to
reconfigure their remote MAC address, even if "locally administered" bit
is set, leading to dropped traffic towards the host. Add a workaround
for that issue already present in cdc_ether to rndis_host driver as
well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit c99013e242)
Fix wrong CPU OPP for ipq8062. Revision of the SoC added an
extra 25mV for every pvs. Also fix the voltage min/max value
that were wrong.
Reviewed-by: Robert Marko robimarko@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
(cherry picked from commit 3f0d87fd69)
The existing device tree has incorrect definitions for usb3_0 and usb3_1
and the blocks they depend upon: their addresses and interrupts are
swapped. However, their clocks and resets are not. The result is that
the USB blocks are non-functional if only one of them is enabled.
This fix backports the definitions from mainline Linux 5.15 to
OpenWrt's 5.10 dtsi additions. See the relevant mainline code here:
https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148
This fix does not break existing ports. But some ports may have enabled
both USB blocks even thought their board only implements one, because
enabling a single USB block would not have worked before this fix.
This means that revisiting all ports of ipq806x devices that implement
a single USB port is advised. This work must be done by maintainers that
can determine which USB block corresponds to the implemented port on
their hardware.
Note that this fix swaps the names of the hardware ports. This is
unfortunate, but will happen anyway when switching to kernel 5.15. Thus,
it is best to do this ASAP, before users get to depend on port names.
It is strongly recommended that this fix is backported to 22.03 before
its release. This will minimize the number of users affected by the port
name swap.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit 284f2c2ae0)
These workarrounds are incomplete and non-functional, and thus not needed.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit 3a4d972d43)
Make it clear, that for `make kernel_{menu,old}config` it's possible to
use only following values for CONFIG_TARGET variable:
* env
* target
* subtarget
* subtarget_target
This should prevent misuse like `make kernel_menuconfig
CONFIG_TARGET=bcm2710` etc.
Keep support for obsolete `platform` and `subtarget_platform` targets
with deprecation notice so this compat stuff could be removed in the
future.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 68e672f32d)
Notify external ubus subscribers of received link-measurement reports.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f6445cfa1a)
Add a ubus method to request link-measurements from connected STAs.
In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 965aa33a18)
Allow external processes to enable advertisement of link-measurement RRM
capability.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2ca5c3da04)
As the LED controller is working now, we can make good use of the LEDs
now.
- Drop the model-name prefix
- Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such
on the casing
- Enable wired LEDs in userspace
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 9024f1e466)
Image metadata and signature is of no use for images which are included
inside other artifacts (like an SD-card image). Strip them off before
using images in artifacts or stashing them for the ImageBuilder as the
contained signature breaks reproducibility.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7a256d97d9)
Improvements since the 4.0.38 release are:
- Rename strtoi to strosi (string to signed int). The strtoi
function on BSD does something else (returns an intmax, not
an int)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 08ebc3881d)
mtools recursive copy (mcopy -s ...) is using READDIR(3) to iterate
over the directory entries, hence they end up in the FAT filesystem in
traversal order which breaks reproducibility (rather than being added
to the FAT filesystem in a reproducible order). Implement recursive
copy in gen_image_generic.sh in Shell code instead, as in that way we
can force files to be copied in reproducible order.
Fixes: aece8f5ae8 ("scripts/gen_image_generic.sh: generate reproducible EFI filesystem")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4d289ae7e6)
Checking whether /sbin/udhcpc is a symbolic link breaks using the
DHCP proto handler inside procd-ujail where bind-mounts are used for
the resolved link. Check whether /sbin/udhcpc is executable instead
to allow using the proto handler for DHCP-provisioned containers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c5f113c43f)
Make sure sysupgrade on NAND also works in case of UBI volumes having
index >9. While at it, also make sure UBI device is detected and abort
in case it isn't. Use Shell built-in shorthand ':' instead of 'true'.
Fixes#9708
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0dbca1b2ba)
Generate FAT filesystem for EFI boot in a reproducible way:
* use '--invariant' option of mkfs.fat
* set timestamps of all files to SOURCE_DATE_EPOCH
* make sure files are ordered locale-independent
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit aece8f5ae8)
Set fixed timestamp for kernel other files in /boot filesystem.
This should help making x86 *combined* images reproducible.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 068ea2cde0)
Use ARMv8 Crypto Extensions for AES, ghash and sha256.
This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit c9c2b01b84)
Specification:
- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit a05dcb0724)
Specification:
- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit c91df224f5)
Changes:
new features:
- qsort_r function (POSIX-future)
- pthread_getname_np extension function
- hard float on SPE FPU for powerpc-sf
- SEEK_DATA and SEEK_HOLE exposed in unistd.h (Linux extensions)
compatibility:
- free now preserves errno (POSIX-future requirement)
- setjmp is declared explicitly with returns_twice for non-GCC compilers
- macro version of isascii is no longer defined for C++
- dynamic linker now tolerates zero-length LOAD segments
- epoll_[p]wait is now a cancellation point
- pwd/grp functions no longer fail on systems without AF_UNIX support
- POSIX TZ parsing is stricter to allow more names to fallback to files
- NULL is now defined as nullptr when used in C++11 or later
- gettext now accepts null pointer as argument
bugs fixed:
- old regression in wcwidth of Hangul combining (vowel/final) letters
- duplocale used wrong malloc when malloc was replaced (1.2.2 regression)
- fmaf rounded wrong on archs without FE_TOWARDZERO (all softfloat archs)
- popen didn't honor requirement not to leak other popen pipe fds to child
- aligned_alloc and variants crashed on allocation failure
- dl_iterate_phdr reported incorrect module TLS pointers
- mishandling of some inputs in acoshf and expm1f and functions using them
- potentially wrong-sign zero in cproj functions at infinity
- multiple bugs in legacy function cuserid
- minor posix_spawn file actions API conformance issues
- pthread_setname_np fd leak
- out-of-bound read in zoneinfo handling with distant-past times
- out-of-tree builds lacked generated debug cfi for x86 asm
arch-specific bugs fixed:
- powerpc (32-bit) struct shmid_ds layout was wrong for some fields
- time64 struct layout was wrong in sound ioctl fallback (32-bit archs)
In addition it contains the following improvements:
* protect stack canary from leak via read-as-string by zeroing second byte
* fix excessively slow TLS performance on some mips models
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 685ae2687b)
The correct readid method is SPINAND_READID_METHOD_OPCODE_ADDR.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
(cherry picked from commit 3711aee56d)
This updates mac80211 to version 5.15.33-1 which is based on kernel
5.15.33.
The removed patches were applied upstream.
This new release contains many fixes which were merged into the upstream
Linux kernel.
This also contains the following new drivers which are needed for ath11k:
* net/qrtr/
* drivers/bus/mhi/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3aa96efa24)
Fixes two high-severity vulnerabilities:
- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
can be bypassed. If a malicious client does not send the
certificate_verify message a client can connect without presenting a
certificate even if the server requires one.
- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
v1.3 server can have its certificate heck bypassed. If the sig_algo in
the certificate_verify message is different than the certificate
message checking may be bypassed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit e89f3e85eb)
Export SOURCE_DATE_EPOCH to environment so filesystem and image
creation tools will make use of it.
Fixes reproducibility of images generated with the ImageBuilder.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 5cf5dce05a)
As anyway only the default is called now we can as well also just remove
the override for Build/Configure.
Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit dffad93d3e)
ARM Trusted Firmware builds do not depend on any target libraries as
they are bare-metal builds. However, the compiler aborts due to
-Werror=missing-include-dirs if the include dir doesn't exists and this
can happen when building with parallelisation as that makes it likely
for arm-trusted-firmware-* to be build very early before any of the
libraries which would implicitely create the directory.
Fix this by making sure the include dir exists before building.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 738d44f5ea)
RT-AC2200 is the same device with a different name. The OEM firmwares have the same MD5.
Signed-off-by: Ray Wang <raywang777@foxmail.com>
(cherry picked from commit 3204906569)
These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.
Note for users sysupgrading from the previous ath79-generic snapshot
images:
The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.
To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".
If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:
* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
(cherry picked from commit 44e1e5d153)
Changes:
Duncan Roe (5):
nlmsg: Fix a missing doxygen section trailer
build: doc: "make" builds & installs a full set of man pages
build: doc: get rid of the need for manual updating of Makefile
build: If doxygen is not available, be sure to report "doxygen: no" to ./configure
src: doc: Fix messed-up Netlink message batch diagram
Fernando Fernandez Mancera (1):
src: fix doxygen function documentation
Florian Westphal (1):
libmnl: zero attribute padding
Guillaume Nault (1):
callback: mark cb_ctl_array 'const' in mnl_cb_run2()
Kylie McClain (1):
examples: nfct-daemon: Fix test building on musl libc
Laura Garcia Liebana (4):
examples: add arp cache dump example
examples: fix neigh max attributes
examples: fix print line format
examples: reduce LOCs during neigh attributes validation
Pablo Neira Ayuso (3):
doxygen: remove EXPORT_SYMBOL from the output
include: add MNL_SOCKET_DUMP_SIZE definition
build: libmnl 1.0.5 release
Petr Vorel (1):
examples: Add rtnl-addr-add.c
Stephen Hemminger (1):
examples: rtnl-addr-dump: fix typo
igo95862 (1):
doxygen: Fixed link to the git source tree on the website.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit c3b7389339)
Changes:
c63f193 bump version to 1.0.2
3cffa84 libnfnetlink: Check getsockname() return code
90ba679 include: Silence gcc warning in linux_list.h
bb4f6c8 Make it clear that this library is deprecated
e46569c Minimally resurrect doxygen documentation
5087de4 libnfnetlink: hide private symbols
62ca426 autogen: don't convert __u16 to u_int16_t
efa1d8e src: Use stdint types everywhere
7a1a07c include: Sync with kernel headers
7633f0c libnfnetlink: initialize attribute padding to resolve valgrind warnings
94b68f3 configure: uclinux is also linux
617fe82 src: get source code license header in sync with current licensing terms
97a3960 build: resolve automake-1.12 warnings
Removed the patch 100-missing_include.patch, libnfnetlink compiles fine
with musl without this patch.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit aecf088b37)
bh_event_add_var can be called by multiple threads concurrently,
so it shall not use a static char buffer
Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
(cherry picked from commit 1e991e09b7)
Override python to use the one in host instead of hostpkg. There's no
need to use the latter.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 19f3fcc884)
The host-build of libselinux requires libsepol/host.
Add the libsepol/host to HOST_BUILD_DEPENDS to allow build on hosts
which don't have libsepol installed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0d3850dc5a)
Problem exist when dnsmasq is exclusively bind to particular interface.
After reconfiguring or restarting this interface, its index changes, but
dnsmasq uses the old one. When this problem occurs, dnsmasq does not
listen on the correct interface so DHCP does not work, and clients do not
get an IP address. Procd netdev param can be added to restart dnsmasq when
the interface index is changed.
Signed-off-by: Valentyn Datsko <valikk.d@gmail.com>
[combined into a single &&-connected statement]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 76f55e3c3f)
Fixes compilation under musl based distros like Alpine Linux.
Also add pcre/host as a build dependency as it's needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit abb2683de3)
The sama7 sub target does not have USB support, the feature should not
be activated there. OpenWrt can automatically detect if the target
supports USB by using the scripts/target-metadata.pl script. With the
automatic detection USB support will only get activated on subtargest
which actually support USB like sam9x and sama5.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f6d566301e)
