Commit Graph

85 Commits

Author SHA1 Message Date
Luis Mita
d780d530dd ramips: mt76x8: sync Cudy TR1200 v1 naming
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.

Signed-off-by: Luis Mita <luis@luismita.com>
2024-06-10 10:13:56 +02:00
Luis Mita
f1091ef7ac ramips: mt76x8: add support for Cudy TR1200 v1
Hardware:
 - SoC: MediaTek MT7628AN (MIPS 580MHz)
 - Flash: 16 MiB XMC 25QH128CH10
 - RAM: 128 MiB ESMT M14D1G1664A
 - WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
 - Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
 - USB 2.0 port
 - Buttons: 1 Reset button, 1 slider button
 - LEDs: 1x Red, 1x White
 - Serial console: unpopulated header, 115200 8n1
 - Power: 5 VDC, 2 A

MAC addresses:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 80:af:ca:xx:xx:x0 | label     |
| LAN     | 80:af:ca:xx:xx:x0 | label     |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label     |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2   |
+---------+-------------------+-----------+

Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.

To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.

If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.

Signed-off-by: Luis Mita <luis@luismita.com>
2024-06-05 10:44:44 +02:00
Lea Teuberth
2a2f53415e ramips: add support for TP-Link Archer MR200v5
Specifications:
	CPU:     MT7628AN 580MHz
	RAM:     64MB DDR2
	FLASH:   8MB EN25QH64 NOR SPI
	WIFI:    2.4GHz 2x2 MT7628 b/g/n internal
	WIFI:    5GHz 1x1 MT7610E ac/n PCI
	LTE:     Qualcomm MDM9207
	ETH:     4xLAN 100base-T integrated
	SWITCH:  RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
	LEDS:    LAN, WAN, Power, 3x signal strength, WiFi
	BTNS:    Reset, WiFi toggle
	UART:    Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1

Installation:
	1. Update using recovery mode
        - set your IP to 192.168.0.225, subnet mask: 255.255.255.0
        - start tftp server, rename tftp-recovery.bin to
          tp_recovery.bin and place it into the server's directory
        - while holdig the "reset" button, power on the device
        - keep holding "reset" until the file is being transferred

Notes:
	This board has only one MAC address programmed
        in the "romfile" partition:
        - MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
        - MAC for phy1 (5GHz) at romfile 0xf100 (-1)
        - stock firmware re-uses phy0 MAC for ethernet
        - stock firmware uses romfile 0xf100 (1) for WWAN;
          not used since QMI interface is raw IP

Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
2024-05-23 22:46:26 +02:00
Steffen Loley
6e7bc0c243 ramips: add support for TP-Link RE205 v3
TP-Link RE205 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with external antennas.
It's based on MediaTek MT7628AN+MT7610EN like the RE200 v3/v4 but with
external antennas.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 5x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)

There are 2.4G and 5G LEDs in blue which are controlled separately.

Installation
------------

Installation is identical to RE200 v3 devices as described at
https://openwrt.org/toh/tp-link/re200#installation

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

U-Boot seems to be locked on newer versions, if not it can be accessed over
the UART as described in the link above.

Signed-off-by: Steffen Loley <slo-src@web.de>
2024-03-23 23:38:33 +01:00
Tomasz Maciej Nowak
0709bd87ba ramips: mt76x8: add support for TP-Link RE365 v1
TP-Link RE365 is a wireless range extender, hardware-wise resembles
RE305 with slight changes regarding buttons and LEDs.

Specification
SoC: MediaTek MT7628AN
RAM: 64 MiB DDR2
Flash: 8 MiB SPI NOR
WiFi: 2.4 GHz 2T2R integrated
      5 GHz 2T2R MediaTek MT7612EN conncted to PCIe lanes
Ethernet: 1x 10/100 Mbps integrated
LEDs: 6x GPIO controlled
Buttons: 4x GPIO controlled
UART: row of 4 holes marked on PCB as J1, starting count from white
      triangle
      1. VCC (3.3V), 2. GND, 3. RX, 4. TX
      baud: 57600, parity: none, flow control: none

Installation
1. Open web management interface.
2. Go to Settings > System Tools > Firmware upgrade.
3. Select "Browse" and select the OpenWrt image with factory.bin suffix.
4. After selecting "Upgrade" firmware writing process will start.
5. Wait till device reboots, power LED should stay solid when it's fully
   booted, then it's ready for configuration through LAN port.

Additional information
With how device manufacturer patrtitioned the flash memory, it's possible
that with default packages set, initial factory.bin image won't be
created. In such case, try to reduce packages amount or use older release
for initial conversion to OpenWrt. Later You can use sysupgrade.bin
image with full set of packages because OpenWrt uses unpartitioned flash
memory space unused by vendor firmware.

Reverting to vendor firmware involves converting firmware using
tplink-safeloader with -z option (can be found in ImageBuilder or SDK)
and forcibly applying converted firmware as sysupgrade.

Known issues
WARNING: after removing casing of the device one is exposed to high
voltage and is in a risk of being electrocuted.

Caution when interfacing whith bootloader, saving its environment either
by issuing "saveenv" or selecting option "1: Load system code to SDRAM
via TFTP." in boot menu, any of those will lead to overwriting part of
kernel. This will lead to need of firmware recovery. The cause of this
issue is bootloader having environment offset on flash at 0x40000,
while kernel starts from 0x20000.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Wrap long line in DTS]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2024-01-10 20:56:06 +01:00
Kamil Jońca
ffa40fcc7f ramips: add TP-LINK TL-WR902AC v4
Seems to be very similar to: https://openwrt.org/toh/tp-link/tl-wr902ac_v3
1 x usb
1 x eth
Powered by mini usb port.

Installation:

Can use TFTP method to install:
1. establish TFTP server at 192.168.0.66
2. provide tp_recover.bin file to the TFTP server
3. turn on router with reset button pressed
4. wait for led blinking, then release reset

Specification based on dmesg from already flashed device:

SoC Type: MediaTek MT7628AN ver:1 eco:2
CPU0 revision is: 00019655 (MIPS 24KEc)
Memory: 56028K/65536K available
CPU Clock: 580MHz
WiFi: MT7613BE

MAC addresses are all the same, except wifi5g which last part is decrement by one, ie.:

eth0		40:ed:00:cf:b9:9b
br-lan		40:ed:00:cf:b9:9b
phy0-ap0	40:ed:00:cf:b9:9b
phy1-ap0	40:ed:00:cf:b9:9a

Signed-off-by: Kamil Jońca <kjonca@onet.pl>
2023-12-06 22:59:22 +01:00
Renaud Gaspard
e9ac1b19e0 ramips: Add support for TP-Link Archer C50 v6 (CA/EU/RU)
This adds support for the TP-Link Archer C50 v6 (CA/EU/RU).
(The ES variant is a rebranded Archer C54 and NOT supported.)

CPU:   MediaTek MT7628 (580MHz)
RAM:   64M DDR2
FLASH: 8M SPI
WiFi:  2.4GHz 2x2 MT7628 b/g/n integrated
WiFi:  5GHz 2x2 MT7613 a/n/ac
ETH:   1x WAN 4x LAN
LED:   Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN:   WPS/WiFi, RESET
UART:  Near ETH ports, 115200 8n1, TP-Link pinout

Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
image (and we do not ship one with the image). We are not able to create
an image in the OpenWRT build-process.

Download a TP-Link image for your device variant (CA/EU or RU) from their
website and a OpenWRT sysupgrade image for the device
and build yourself a factory image like following:

TP-Link image:             tpl.bin
OpenWRT sysupgrade image:  owrt.bin

 > dd if=tpl.bin of=boot.bin bs=131584 count=1
 > cat owrt.bin >> boot.bin

Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.

Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.

Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.

The boot.bin can now be uploaded and flashed using the web-recovery.

Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)

 > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
 > dd if=tpl.bin of=tmp.bin bs=131584 count=1
 > dd if=tmp.bin of=boot.bin bs=512 skip=1
 > cat boot.bin >> tp_recovery.bin
 > cat owrt.bin >> tp_recovery.bin

Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.

Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.

U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.

Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.

Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.

By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.

It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.

Co-authored-by: Julius Schwartzenberg <julius.schwartzenberg@gmail.com>
Signed-off-by: Renaud Gaspard <gaspardrenaud@hotmail.com>
Signed-off-by: Julius Schwartzenberg <julius.schwartzenberg@gmail.com>
Tested-by: Julius Schwartzenberg <julius.schwartzenberg@gmail.com>
Tested-by: Jaroslav Mikulík <byczech@gmail.com>
Tested-by: Ashipa Eko <ashipa.eko@gmail.com>
2023-11-19 21:29:39 +01:00
Bin We
6b66666da4 ramips: add support for OrayBox X1
Add support for OrayBox X1. It is a 802.11n router, based on MediaTek MT7628N.

Specifications:
SoC: MediaTek MT7628N (580MHz)
RAM: 64 MiB
Flash: 16 MiB NOR (Winbond W25Q128JVSIQ)
Wireless: 802.11b/g/n 2x2 2.4GHz (Built In)
Ethernet: 1x 100Mbps only
USB: 1x USB Type-A 2.0 Host Port
Button: 1x "Reset" button
LED: 1x Blue LED + 1x Red LED + 1x White LED
Power: 5V Micro-USB input

Manufacturer Page:
https://pgy.oray.com/router/x1.html/parameter

Flash Layout:
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "kpanic"
0x000000040000-0x000000050000 : "factory"
0x000000050000-0x000000fe0000 : "firmware"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "reserve"

Install via SSH:
Original firmware is based on OpenWRT, but SSH is not start by default,
You should enable it first

1. Login into web admin (10.168.1.1), default password is 'admin'
2. Open the following link, and the result should be {"code":0};
SSH is now started, username is root, password is same as web admin password
http://10.168.1.1/cgi-bin/oraybox?_api=ssh_set&enabled=1
4. You can flash firmware via mtd: mtd write /tmp/firmware_image.bin firmware

Signed-off-by: Bin We <me@udp.pw>
2023-04-02 19:25:37 +02:00
Maxim Anisimov
3690c4a092 ramips: improve support for Zyxel Keenetic Extra II
- drop unneeded default-state for led_power
- concat firmware partitions to extend available free space
- increase spi flash frequency to 32 Mhz (value from stock firmware bootlog)
- drop broken-flash-reset because of onboard flash chip W25Q256FV has reset support
- add compatible for pcie wifi according to kernel documetation
- switch to wan mac address with offset 0x28 in rf-eeprom

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-28 21:45:34 +01:00
Maxim Anisimov
dbebfb88b5 ramips: add support for Keenetic KN-1613
Keenetic KN-1613 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7628AN.

Specification:
- System-On-Chip: MT7628AN
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 4x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-1613-squashfs-factory.bin"
   to "KN-1613_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2023-01-06 17:53:10 +01:00
Julien Dusser
b893aa7992 ramips: add support for Linksys E5400 and clones
Linksys E5400 is a 2.4/5GHz dual band AC router, based on MediaTek
MT7628AN. This device is also sold as Linksys E2500v4, E5300 and E5350
with the same hardware, but software speed limitations in vendor
firmwares.

Specification:
 * SoC: MT7628AN (580 MHz)
 * RAM: DDR2 64 MiB
 * Flash: 16 MiB NOR (W25Q128BV)
 * Wi-Fi:
   * 2.4GHz: SoC Built-in
   * 5GHz: MT7612EN
 * Ethernet: 5x 100Mbps
   * Switch: SoC built-in
 * UART:
   * 115200, 8N1, 3.3V (real u-boot speed: 119050)
   * Pinout JB4: 1:[3V3] (TXD) (RXD) [NC] (GND)

Flash Layout:
  0x0000000-0x0030000 : "Bootloader"
  0x0030000-0x0040000 : "Config"
  0x0040000-0x0050000 : "Factory"
  0x0050000-0x0ff0000 : "Kernel"
  0x0ff0000-0x1000000 : "CBTinfo"

MAC address:
  LAN: factory 0x28
  WAN: LAN + 1
  2.4G: LAN + 2
  5G: LAN + 3

Installation:
1. Connect to UART, use LF as EOL (not CRLF)
2. Set IP address
  - Press 4 during boot
  - setenv serverip <TFTPSERVER_IP>
  - setenv ipaddr <DEVICE_IP>
  - setenv bootfile openwrt-ramips-mt76x8-linksys_e5400-initramfs-kernel.bin
  - saveenv
  - reset
3. Load Openwrt Kernel image from TFTP:
  - Press 1 during boot
  - IP and filename should be already set
4. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2022-12-18 21:24:57 +01:00
Senis John
a8f3c97ce8 ramips: add support for HiWiFi HC5611
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1

1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`

I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot

Signed-off-by: Senis John <thank243@gmail.com>
2022-12-04 15:21:12 +08:00
Shiji Yang
288b36c2ea ramips: add missing WAN LED for Xiaomi Mi Router 4A / 4C
The blue WAN LED connected to GPIO37 is missing, so re-add it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-10-23 23:33:22 +02:00
Andrey Butirsky
47d58afbdf ramips: kndrt31r19: set up wan interface by default
The only WAN port of the device is it's modem, so set it up as such

Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-10-19 23:00:40 +02:00
Andrey Butirsky
5806914794 ramips: add support for Kroks Rt-Cse SIM Injector DS
Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958:
https://kroks.ru/search/?text=1958
See Kroks OpenWrt fork for support of other models:
https://github.com/kroks-free/openwrt

Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 5x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- USB: 1x
- SIM-reader: 2x (driven by a dedicated chip with it's own firmware)
- Buttons: reset
- LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.)

Flashing:
- sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254
- U-Boot launches a WEB server if Reset button is held during power up,
  IP: 192.168.1.1

MAC addresses as verified by OEM firmware:
vendor   OpenWrt   source
LAN      eth0      factory 0x4 (label)
2g       wlan0     label

Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-09-11 01:30:11 +02:00
Andrey Butirsky
0a79c77a4e ramips: add support for Kroks Rt-Pot mXw DS RSIM router
Aka "Kroks KNdRt31R19".
Ported from v19.07.8 of OpenWrt fork:
see https://github.com/kroks-free/openwrt
for support of other models.

Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- mPCIe: 1x (usually equipped with an LTE modem by vendor)
- Buttons: reset
- LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status

Flashing:
- sysupgrade image via stock firmware WEB interface.
- U-Boot launches a WEB server if Reset button is held during power up.
Server IP: 192.168.1.1

SIM card switching:
The device supports up to 4 SIM cards - 2 locally on board and 2 on
remote SIM-injector.
By default, 1-st local SIM is active.
To switch to e.g. 1-st remote SIM:
echo 0 > /sys/class/gpio/modem1power/value
echo 0 > /sys/class/gpio/modem1sim1/value
echo 1 > /sys/class/gpio/modem1rsim1/value
echo 1 > /sys/class/gpio/modem1power/value

MAC addresses as verified by OEM firmware:
vendor   OpenWrt   source
LAN      eth0      factory 0x4 (label)
2g       wlan0     label

Signed-off-by: Kroks <dev@kroks.ru>
[butirsky@gmail.com: port to master; drop dts-v1]
Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-09-11 01:30:11 +02:00
Nita Vesa
1a8c74da70 ramips: Add Xiaomi Mi Router 4A 100M International
The international version of Mi Router 4A 100M is physically
identical to the non-international one, but appears to be
using a different partitioning scheme with the "overlay"
partition being 2MiB in size instead of 1MiB. This means
the following "firmware" partition starts at a different
address and the DTS needs to be adjusted for the firmware
to work.

Signed-off-by: Nita Vesa <werecatf@outlook.com>
2022-07-03 22:14:05 +02:00
Sergei Iudin
4b0c433c39 ramips: Add suport for COMFAST CF-WR617AC
Specifications:
Chipset:MT7628DA+MT7612E
Antenna : 2.4Ghz:2x5dbi Antenna + 5.8Ghz:2x5dbi Antenna
Wireless Rate:2.4Ghz 300Mbps , 5.8Ghz 867Mbps
Output Power :100mW(20dbm)
Physical port:110/100Mbps RJ45 WAN Port , 310/100Mbps RJ45 LAN Port
Flash: 8Mb
DRam: 64Mb
Flashing: default bootloader attempts to boot from tftp://192.168.1.10/firmware_auto.bin using 192.168.1.1

Known issues:
mac-address-increment for 5GHZ doesnt work, i failed to figure out why. Original firmware using +1 from original value in factory partition.

Signed-off-by: Sergei Iudin <tsipa740@gmail.com>
2022-07-03 22:14:05 +02:00
Tamas Balogh
a4bf562aa7 ramips: add support for ASUS RT-AC1200-V2
Hardware specifications:
SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi: MT7613BEN 5G-ac 160MHz 2x2
Switch: 4x100M built-in SoC
Flash: 16MB W25Q128JVSQ SPI-NOR
DRAM: 64MB built-in SoC

MAC addresses as verified by OEM firmware:
use address source
Lan/Wan/2G *:60 factory 0x4 (label)
5G *:64 factory 0x8000

Serial console: 57600,8n1

Installation:

Asus windows recovery tool:

install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
start the Asus firmware restoration utility, specify the factory image
and press upload
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
TFTP Recovery method:

set computer to a static ip, 192.168.1.75
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-04-16 15:30:11 +02:00
Davide Fioravanti
bb505d82ad ramips: add support for Wavlink WL-WN531A3
The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports
and one USB 2.0 port.
It's also known as Wavlink QUANTUM D4.

Hardware
--------
SoC:   Mediatek MT7628AN
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3)
ETH:
  - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 external antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x Turbo button
  - 1x Touchlink button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
  - 1x USB 2.0 port
UART:
  - 57600-8-N-1
    J1
      O VCC +3,3V (near lan ports)
      o RX
      o TX
      o GND

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M31A3.V4300.200420 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
	-rw-r--r--    1 0        0         8388608 /etc_ro/lighttpd/www/dev/mtd0ro

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/

6) After few seconds, in the textarea should appear this output:
	-rw-r--r--    1 0        0          196608 mtd1ro
	-rw-r--r--    1 0        0           65536 mtd2ro
	-rw-r--r--    1 0        0           65536 mtd3ro
	-rw-r--r--    1 0        0         8060928 mtd4ro
	drwxr-xr-x    7 0        0               0 ..
	drwxr-xr-x    2 0        0               0 .

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:9B (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:9C (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:9D (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:9E (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:9D

2) There is just one wifi led for both wifi interfaces.
   It currently shows only the 2.4 GHz wifi activity.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-04-16 14:02:11 +02:00
Shiji Yang
2e6d19ee32 ramips: fix wifi mac address of HiWiFi series devices
For HiWiFi series devices, label_mac can be read from bdinfo partition,
and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac
to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's
label_mac start with D4:EE)

For example:
label	D4:EE:07:32:84:88
lan	D4:EE:07:32:84:88
wan	D4:EE:07:32:84:89
wlan2g	D4:EE:07:32:84:88
wlan5g	D0:EE:07:32:84:88

Tested on HiWiFi HC5661.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-03-26 02:02:44 +01:00
Ray Wang
3c4810fecc ramips: add support for Asus RT-AC1200
Asus RT-AC1200 is a 2.4/5GHz dual band AC router,
based on MediaTek MT7628AN.

Specification:
* SoC: MT7628AN
* RAM: DDR2 64 MiB
* Flash: 16 MiB NOR (W25Q128BV)
* Wi-Fi:
  * 2.4GHz: SoC Built-in
  * 5GHz: MT7612EN
* Ethernet: 5x 100Mbps
  * Switch: SoC built-in
* USB: 1x 2.0

Flash Layout:
 0x0000000-0x0030000 : "bootloader"
 0x0030000-0x0040000 : "nvram"
 0x0040000-0x0050000 : "factory"
 0x0050000-0x1000000 : "firmware"

MAC address:
 LAN: factory 0x28
 WAN: factory 0x22
 2.4G: factory 0x4
 5G: factory 0x8004

Installation via **recovery** mode:
1. Download the Asus recovery firmware (windows) tool from
   http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip
2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO
   gateway.
3. Plug in your ethernet to LAN port 1 on the router.
4. Load up the recovery software with the firmware file, but don't press
   "Upload" yet.
5. Plug in the router to power WHILE HOLDING the reset button in. While
   CONTINUING to hold the button, select "Upload" Continue to hold the
   reset button in until it finishes and verifies!
6. If that doesn't work try pressing "Upload" first just before you do
   step 5. At some point while holding reset the rescue tool will finally
   detect and upload the firmware. That's when you can let go of the
   reset button.
7. The router will reboot and not much will happen. Wait a minute or 2.
8. Power off and on the router again. Voila. Set everything your Ethernet
   IP back to DHCP (automatically) and you're good to go.

Revert to stock firmware:
1. Install stock image via recovery mode.

Tested-by: Ivan Pavlov <AuthorReflex@gmail.com>
Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-03-09 15:38:28 +09:00
INAGAKI Hiroshi
770cfe9bff ramips: update MAC address configuration for Buffalo WCR-1166DS
This patch converts MAC address configuration of Buffalo WCR-1166DS in
02_network to use the generic function of OpenWrt. And also, add
label_mac.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-03-06 20:05:45 +01:00
Rodrigo Araujo
7c8ade1765 ramips: correct vendor name for COMFAST/Joowin
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.

Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.

As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.

Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-22 01:17:04 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Sungbo Eo
91e37b60a0 ramips: mt76x8: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-12 20:25:56 +09:00
Sergey V. Lobanov
e22c91e144 ramips: fix tl-mr3020-v3 switch topology to configure vlans via luci
Currently it is not possible to configure VLANs via LUCI on
tplink tl-mr3020-v3. This patch fixes switch topology for the
LUCI interface.

Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
[copied commit message from github PR]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Thomas Aldrian
b28443f82e ramips: add support for Wavlink WL-WN576A2
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.

Device specs:

- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS

Flashing:

U-Boot launches a TFTP client if WPS button is held during boot.

- Server IP: 192.168.10.100
- Firmware file name: firmware.bin

Device will reboot automatically. First boot takes about 90s.

Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.

Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
2021-11-20 21:08:25 +01:00
Eduardo Santos
3c97fb4346 ramips: add support for Xiaomi MiWifi 3C
This commit adds support for Xiaomi MiWiFi 3C device.

Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.

The differences are:

 - Numbers of antennas (4 instead of 2). The antenna management
   is done via the µC. There is no configuration needed in the
   software code.
 - LAN port assignments are different. LAN1 and WAN are
   interchanged.

OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c

OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c

Specifications:

 - CPU: MediaTek MT7628AN (575MHz)
 - Flash: 16MB
 - RAM: 64MB DDR2
 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
 - Antennas: 4x external single band antennas
 - WAN: 1x 10/100M
 - LAN: 2x 10/100M
 - LED: 1x amber/blue/red. Programmable
 - Button: Reset

MAC addresses as verified by OEM firmware:

use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4

OEM firmware uses VLAN's to create the network interface for WAN and LAN.

Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".

How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
   https://github.com/acecilia/OpenWRTInvasion
   (IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command  "dd if=/dev/mtd0 of=/tmp/mtd0".
   Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
   to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```

Limitations: For the first install the image size needs to be less
than 7733248 bits.

Thanks for all community and especially for this device:
minax007, earth08, S.Farid

Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
 &wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-31 21:24:47 +01:00
Michal Kozuch
c12ef2f760 ramips: add support for TP-Link RE305 v3
Specs (same as in v1):
- MT7628AN (575 MHz)
- 64MB RAM
- 8MB of flash (SPI NOR)
- 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan)
- 1x 2.4GHz wifi (MT7628AN)
- 1x 5Ghz wifi (MT7612E)
- 4x LEDs (5 GPIO-controlled)
- 1x reset button
- 1x WPS button

The only and important difference between v1 & v3 is in flash memory
layout, so pls don't interchange these 2 builds!

Installation through web-ui (on OEM factory firmware):
1. Visit http://tplinkrepeater.net or the configured IP address of
   your RE305 v3 (default 192.168.0.254).
2. Log in with the password you've set during initial setup of the
   RE305 (there is no default password).
3. Go to Settings -> System Tools -> Firmware upgrade
4. Click Browse and select the OpenWRT image with factory.bin suffix
   (not sysupgrade.bin)
5. A window with a progress bar will appear. Wait until it completes.
6. The RE305 will reboot into OpenWRT and serve DHCP requests on the
   ethernet port.
7. Connect an RJ45 cable from the RE305 to your computer and access
   LuCI at http://192.168.1.1/ to configure (or use ssh).

Disassembly:
Just unscrew 4 screws in the corners & take off the back cover.
Serial is exposed to the right side of the main board (in the middle)
and marked with TX/RX/3V3/GND, but the holes are filled with solder.

Installation through serial:
1. connect trough serial (1n8, baudrate=57600)
2. setup the TFTP server and connect it via ethernet
   (ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc)
3. boot from a initramfs image first (choose 1 in the bootloader
   options)
4. test it a bit with that, then proceed to run sysupgrade build

MAC addresses as verified by OEM firmware:

  use  OpenWrt  address  reference
  LAN  eth0     *:d2     label
  2g   wlan0    *:d1     label - 1
  5g   wlan1    *:d0     label - 2

  The label MAC address can be found in config 0x2008.

Signed-off-by: Michal Kozuch <servitkar@gmail.com>
[redistribute WLAN node properties between DTS/DTSI, remove
 compatible on DTSI, fix indent/wrapping, split out firmware-utils
 change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:05:25 +02:00
Alexander Couzens
c39be8e7a4
ramips: minew g1-c: use default static address for lan instead of dhcp
As Adrian Schmutzler suggested on github [1] the device should follow the
default behaviour on ethernet using a static address instead using dhcp.

[1] 8d497b6570

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-08-31 02:42:32 +02:00
Giovanni Cascione
d57ba86e48 ramips: add support for D-Link DAP-1325-A1
This patch adds support for D-Link DAP-1325-A1 (Range Extender Wi-Fi N300)

Specifications:
- SoC: 580Mhz MT7628NN
- RAM: 64MB, DDR2 SDRAM
- Storage: 8MB, SPI (W25Q64JVSSIQ)
- Ethernet: 1x 10/100 LAN port
- WIFI: 2.4 GHz 802.11bgn
- LED: Status (2x to provide 3 colors), Wi-Fi Signal Strength (4x)
- Buttons: Reset, WPS
- UART: Serial console (57600, 8n1)
Row of 4 holes near LAN port, starting from square hole:
3.3V, TX,RX,GND
- FCC ID: fccid.io/KA2AP1325A1/

Installation:

Failsafe UI
Firmware can be uploaded with Failsafe UI web page:
- turn device off
- press and hold reset button
- turn device on
- keep holding reset until red wifi strength led turns on (ab. 10sec)
- connect to device through LAN port
PC must be configured with static ip (192.168.0.x)
- connect to 192.168.0.50
- select image to be flashed and upload.
Device will reboot after successful update

Serial port/TFTP server
- Connect through serial connectors on PCB (e.g. with teraterm)
- Set up a TFTP server, and connect through LAN with static IP
- Put image file in the root of the server
- Boot the device and select '2' at U-Boot startup
- Set device IP, server IP and image file name
- Start upload and flash

Signed-off-by: Giovanni Cascione <ing.cascione@gmail.com>
[fix whitespaces in DTS, convert to nvmem, add mtd-eeprom]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:42:17 +02:00
Shiji Yang
09143282bd ramips: add support for Motorola MWR03
Specifications:
* SOC: MT7628AN + MT7612E
* ROM: 8 MiB Flash
* RAM: 64 MiB DDR2
* WAN: 10/100M *1
* LAN: 10/100M *3
* Button: Reset *1
* LEDs: orange *1, white *1
* Antennas: 2.4 GHz *2 + 5 GHz *2
* TTL Baudrate: 57600
* TFTP Upgrade: IP: 192.168.51.1, Server: 192.168.51.100

MAC addresses as verified by OEM firmware:

use   address   source
2g    *:d8      factory 0x0004 (label)
5g    *:d9      factory 0x8004
LAN   *:d7      factory $label -1
WAN   *:da      factory $label +2

Installation (TFTP + U-Boot):
 * Connect device with a TTL cable and open a serial session by
   PuTTY.
 * Press "2" when booting to select "Load system code then write
   to Flash via TFTP".
 * Configure the IP of local host server.
 * Upload firmware by tftpd64, it will boot when write instruction
   is executed.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix DTS line endings, fix label MAC address, adjust status LED
 names, convert mtd-mac-address-increment to mac-address-increment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:41:35 +02:00
Adrian Schmutzler
c23bc5032f ramips: add label MAC address for Onion Omega 2(+)
Thanks to a hint from Michael Siegenthaler in 4b4fa2f9fe ("ramips:
fix ethernet MAC address on Omega2"), the label MAC address of
the Onion Omega 2(+) can be set based on its documentation [1].

[1] https://docs.onion.io/omega2-docs/mac-address.html

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-21 23:42:32 +02:00
Alexander Couzens
8d497b6570
ramips: add support for minew g1-c
The minew g1-c is a smart home gateway / BLE gateway.
A Nordic nRF52832 is available via USB UART (cp210x) to support BLE.
The LED ring is a ring of 24x ws2812b connect to a generic GPIO (unsupported).
There is a small LED which is only visible when the device is open which
will be used as LED until the ws2812b is supported.
The board has also a micro sdcard/tfcard slot (untested).
The Nordic nRF52832 exposes SWD over a 5pin header (GND, VCC, SWD, SWC, RST).
The vendor uses an older OpenWrt version, sysupgrade can be used via
serial or ssh.

CPU:		MT7628AN / 580MHz
RAM:		DDR2 128 MiB RAM
Flash:		SPI NOR 16 MiB W25Q128
Ethernet:	1x 100 mbit (Port 0) (PoE in)
USB:		USB hub, 2x external, 1x internal to USB UART
Power:		via micro usb or PoE 802.11af
UART:		3.3V, 115200 8n1

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-07-05 17:27:13 +02:00
Liu Yu
ae9c5cd37b ramips: fix Ethernet random MAC address for HILINK HLK-7628N
Set the ethernet address from flash.

MAC addresses as verified by OEM firmware:

  use   interface  source
  2g    wlan0      factory 0x04 (label)
  LAN   eth0.1     factory 0x28 (label+1)
  WAN   eth0.2     factory 0x2e (label+2)

Fixes: 671c9d16e3 ("ramips: add support for HILINK HLK-7628N")

Signed-off-by: Liu Yu <f78fk@live.com>
[drop old MAC address setup from 02_network, cut out state_default
changes, face-lift commit message, add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-09 22:18:37 +02:00
Thomas Aldrian
f755d81999 ramips: add support for Wavlink WL-WN578A2
This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug
wireless router. This device is also sold under the name SilverCrest
SWV 733 A2.

Device Specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high
- Buttons: Reset, WPS
- Sliding mode switch: AP, repeater, client
- Small sliding power switch

Flashing instructions:

U-Boot launches TFTP client if WPS button is pressed during power-on.
Configure as follows:

- Server IP: 192.168.10.100
- Filename (rename sysupgrade file to this): firmware.bin

Flashing should not take more than a minute, device will reboot
automatically.

Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
2021-05-28 01:12:21 +02:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
INAGAKI Hiroshi
08768b44d9 ramips: add support for ELECOM WRC-1167FS
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7628AN.

Specification:

- SoC		: MediaTek MT7628AN
- RAM		: DDR2 64 MiB (NT5TU32M16FG-AC)
- Flash		: SPI-NOR 16 MiB (W25Q128JVSIQ)
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7628AN (SoC)
  - 5 GHz	: MediaTek MT7612E
- Ethernet	: 10/100 Mbps x2
  - Switch	: MT7628AN (SoC)
- LEDs/Keys	: 6x, 3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: 3.3V, GND, TX, RX from "J1" marking
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WRC-1167FS normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button to
   perform firmware update
4. Wait ~120 seconds to complete flashing

Notes:

- Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware

- Additional padding in factory image is required to avoid incomplete
  flashing on stock firmware

MAC addresses:

- LAN	: BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28   (hex))
- WAN	: BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22   (hex))
- 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac    (text) / Factory, 0x4    (hex))
- 5GHz	: BC:5C:4C:xx:xx:6B (Config, rmac2   (text) / Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-02-11 16:37:53 +01:00
Ewan Parker
ddafcc7947 ramips: add support for Hi-Link HLK-7688A
Specifications:

  - SoC: MediaTek MT7688AN
  - RAM: 128 MB
  - Flash: 32 MB
  - Ethernet: 5x 10/100 (1x WAN, 4x LAN)
  - Wireless: built in 2.4GHz (bgn)
  - USB: 1x USB 2.0 port
  - Buttons: 1x Reset
  - LEDs: 1x (WiFi)

Flash instructions:

  - Configure TFTP server with IP address 10.10.10.3
  - Name the firmware file as firmware.bin
  - Connect any Ethernet port to the TFTP server's LAN
  - Choose option 2 in U-Boot
  - Alternatively choose option 7 to upload firmware to the built-in
    web server

MAC addresses as verified by OEM firmware:

  use   address   source
  2g    *:XX      factory 0x4
  LAN   *:XX+1    factory 0x28
  WAN   *:XX+1    factory 0x2e

Notes:

This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage.  The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.

From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM.  For those, updating
U-Boot is recommended.

Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 14:54:47 +01:00
Adrian Schmutzler
6d4382711a ramips: use full names for Xiaomi Mi Router devices
This aligns the device/image names of the older Xiaomi Mi Router
devices with their "friendly" model and DEVICE_MODEL properties.

This also reintroduces consistency with the newer devices already
following that scheme.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-08 17:18:57 +01:00
Ataberk Özen
4287f73989 ramips: add support for Xiaomi Mi Router 4C
This commit adds support for Xiaomi's Mi Router 4C device.

Specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
                      - Non-programmable (shows WAN activity)
- Button: Reset

How to install:

1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
   Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
   the router..
5- It takes around 2 minutes. After that router will restart itself
   to OpenWrt.

Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com>
[wrap commit message, bump PKG_RELEASE for uboot-envtools, remove
dts-v1 from DTS, fix LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-25 19:34:13 +01:00
Filip Moc
b641eb6ecf ramips: add support for TP-Link MR6400 v5
TL-MR6400v5 is very similar to TL-MR6400v4. Main differences are:
  - smaller form factor
  - different LED GPIOs
  - different switch connections

You can flash via tftp recovery:
 - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
 - connect to any ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button

Flashing via OEM web interface does not work.

LTE module does not support DHCP so it must be configured via QMI.

Hardware Specification (v5.0 EU):
 - SoC: MT7628NN
 - Flash: Winbond W25Q64JVS (8MiB)
 - RAM: ESMT M14D5121632A (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 1NIC (4x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 9V 0.85A

Signed-off-by: Filip Moc <lede@moc6.cz>
2020-11-25 13:23:06 +01:00
Filip Moc
0d65177658 ramips: add support for TP-Link MR6400 v4
You can flash via tftp recovery:
 - serve tftp-recovery image as /tp_recovery.bin on 192.168.0.225/24
 - connect to any ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button

Flashing via OEM web interface does not work.

LTE module does not support DHCP so it must be configured via QMI.

Hardware Specification (v4.0 EU):
 - SoC: MT7628NN
 - Flash: Winbond W25Q64JVS (8MiB)
 - RAM: ESMT M14D5121632A (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 1NIC (4x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 9V 0.85A

Signed-off-by: Filip Moc <lede@moc6.cz>
2020-11-23 00:46:40 +00:00
Marc Egerton
f276395cda ramips: add support for the Hak5 WiFi Pineapple Mark 7
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.

Specifications:
    * SoC: MediaTek MT7628 (580MHz)
    * RAM: 256MiB (DDR2)
    * Storage 1: 32MiB NOR (SPI)
    * Storage 2: 2GB eMMC
    * Wireless 1: 802.11b/g/n 2.4GHz (Built In)
    * Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
    * Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
    * USB: 1x USB Type-A 2.0 Host Port
    * Ethernet: 1x USB Type-C AX88772C Ethernet
    * UART: 57600 8N1 on PCB
    * Inputs: 1x Reset Button
    * Outputs: 1x RGB LED
    * FCCID: 2AA52MK7

Flash Instructions:
    Original firmware is based on OpenWRT.
    Use sysupgrade via SSH to flash.

Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2020-11-18 23:49:34 +01:00
Richard Fröhning
33b76d66d1 ramips: add support for TP-Link RE200 v4
TP-Link RE200 v4 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas.
It's based on MediaTek MT7628AN+MT7610EN like the v2/v3.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

The MAC address assignment matches stock firmware, i.e.:

LAN : *:8E
2.4G: *:8D
5G  : *:8C

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

Instructions for serial console and recovery may be checked out in
commit 6d6f36ae78 ("ramips: add support for TP-Link RE200 v2") or on
the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[removed empty line, fix commit message formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-10-20 03:01:13 +02:00
Adrian Schmutzler
2230fe3922 ramips: remove set_wifi_led function in 01_leds
While we mostly use the ucidef_set_led_* functions directly in 01_leds
we still have the set_wifi_led function in parallel for several old
devices. This is not only inconsistent with the other definitions,
it also links to the wlan0 interface instead of using a phy trigger
which would be independent of the interface name (and is used for
all newer devices anyway). Apart from that, the standard names
"wifi" and "wifi-led" are not very helpful in a world with different
radio bands either.

Thus, this patch removes the set_wifi_led function and puts the
relevant commands into the cases explicitly. This makes the
mechanism used more evident and will hopefully lead to some future
improvements or at least prevent some copy-pasting of the old
setups.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-02 14:51:57 +02:00
Adrian Schmutzler
ed5933beb6 ramips: remove option to set WiFi LED via aliases
In ramips, it's not common to use an alias for specifying the WiFi
LED; actually only one device uses this mechanism (TL-WR841N v14).

Particularly since the WiFi LEDs are typically distinguished between
2.4G and 5G etc. it is also not very useful for this target.

Thus, this patch removes the setup lines for this mechanism and
converts the TL-WR841N v14 to the normal setup.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-02 14:51:57 +02:00
Adrian Schmutzler
c846dd91f0 ramips: remove model name from LED labels
Like in the previous patch for ath79 target, this will remove the
"devicename" from LED labels in ramips as well.

The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated.

For the latter, all existing definitions were actually just
devicename migrations anyway. Therefore, those are removed and
a common migration file is created in target base-files. This is
actually another example of how the devicename removal makes things
easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-02 14:51:57 +02:00
Andrew Freeman
ff5dd32164 ramips: add support for TP-Link TL-WR850N v2
This patch adds support for the TP-Link TL-WR850N v2. This device
is very similar to TP-Link TL-WR840 v4 and TP-Link TL-WR841 v13.

Specifications:
SOC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
WLAN: MediaTek MT7628NN
Ethernet: 5 ports (100M)

Installation Using the integrated tftp capability of the router:
1. Turn off the router.
2. Connect pc to one of the router LAN ports.
3. Set your PC IPv4 address to 192.168.0.66/24.
4. Run any TFTP server on the PC.
5. Put the recovery firmware on the root directory of TFTP server
   and name the file tp_recovery.bin
6. Start the router by pressing power button while holding the
   WPS/Reset button (or both WPS/Reset and WIFI buttons)
7. Router connects to your PC with IPv4 address 192.168.0.2,
   downloads the firmware, installs it and reboots. LEDs are
   flashing. Now you have OpenWrt installed.
8. Change your IPv4 PC address to something in 192.168.1.0/24
   network or use DHCP to get an address from your OpenWrt router.
9. Done! You can login to your router via ssh.

Forum link:
https://forum.openwrt.org/t/add-support-for-tp-link-tl-wr850n-v2/66899

Signed-off-by: Andrew Freeman <labz56@gmail.com>
[squash an tidy up commits, sort nodes]
Signed-off-by: Darsh Patel <darshkpatel@gmail.com>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-27 16:36:18 +02:00