The Netgear GS3xx devices do not properly initialise the port LEDs during
startup unless the boot command in U-Boot is changed. Making the U-Boot
env partition writable allows this modification to be done from within
OpenWrt by calling "fw_setenv bootcmd rtk network on\; boota".
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Make the u-boot environment partition for the NETGEAR
GS108T v3 and GS110TPP writable (they share a DTS), so
the values can be manipulated from userspace.
See https://forum.openwrt.org/t/57875/1567 for a real
world example.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
This model is almost identical to the EAP225-Outdoor v1.
Major difference is the RTL8211FS PHY Chipset.
Device specifications:
* SoC: QCA9563 @ 775MHz
* Memory: 128MiB DDR2
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 2x2
* Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO
* Ethernet (RTL8211FS): 1× 1GbE, PoE
Flashing instructions:
* ssh into target device with recent (>= v1.6.0) firmware
* run `cliclientd stopcs` on target device
* upload factory image via web interface
Debricking:
To recover the device, you need access to the serial port. This requires
fine soldering to test points, or the use of probe pins.
* Open the case and solder wires to the test points: RXD, TXD and TPGND4
* Use a 3.3V UART, 115200 baud, 8n1
* Interrupt bootloader by holding ctrl+B during boot
* upload initramfs via built-in tftp client and perform sysupgrade
setenv ipaddr 192.168.1.1 # default, change as required
setenv serverip 192.168.1.10 # default, change as required
tftp 0x80800000 initramfs.bin
bootelf $fileaddr
MAC addresses:
MAC address (as on device label) is stored in device info partition at
an offset of 8 bytes. ath9k device has same address as ethernet, ath10k
uses address incremented by 1.
From stock ifconfig:
ath0 Link encap:Ethernet HWaddr D8:...:2E
ath10 Link encap:Ethernet HWaddr D8:...:2F
br0 Link encap:Ethernet HWaddr D8:...:2E
eth0 Link encap:Ethernet HWaddr D8:...:2E
Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de>
Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de>
Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de>
[Add pre-calibraton nvme-cells]
Tested-by: Tido Klaassen <tido_ff@4gh.eu>
Signed-off-by: Nick Hainke <vincent@systemli.org>
4554ee652caf mt76: mt7921: fix warning Using plain integer as NULL pointer
a3f1d6ccf3ca mt76: mt7921: add missing bh-disable around rx napi schedule
9aeca2a5ce47 mt76: mt7921: get rid of mt7921_mcu_exit
fee8a5911c76 mt76: connac: move shared fw structures in connac module
db4d784ae7ba mt76: mt7921: move fw toggle in mt7921_load_firmware
16ab6bf49556 mt76: connac: move mt76_connac2_load_ram in connac module
29fd748801c6 mt76: connac: move mt76_connac2_load_patch in connac module
051c68d18214 mt76: mt7663: rely on mt76_connac2_fw_trailer
d6ae3505ac6c mt76: enable the VHT extended NSS BW feature
488a5ccc9762 mt76: mt7921: rely on mt76_dev in mt7921_mac_write_txwi signature
934029bb93e2 mt76: mt7915: rely on mt76_dev in mt7915_mac_write_txwi signature
ecefae4c7d72 mt76: connac: move mac connac2 defs in mt76_connac2_mac.h
b5eecc841df8 mt76: connac: move connac2_mac_write_txwi in mt76_connac module
012e619a07b9 mt76: connac: move mt76_connac2_mac_add_txs_skb in connac module
1b492be795ea mt76: mt7921: not support beacon offload disable command
f1f46d3b4b19 mt76: mt7921: fix command timeout in AP stop period
cae61112ef1d mt76: connac: move HE radiotap parsing in connac module
487674062643 mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module
649bdc4983c4 mt76: connac: move mt76_connac2_mac_fill_rx_rate in connac module
cb75aaa39252 mt76: mt7921s: remove unnecessary goto in mt7921s_mcu_drv_pmctrl
e0eaf66eaebb mt76: mt7615: do not update pm stats in case of error
f8d125b4ea30 mt76: mt7921: do not update pm states in case of error
6329a834907e mt76: mt7921s: fix possible sdio deadlock in command fail
8a04f1b04662 mt76: mt7921: fix aggregation subframes setting to HE max
e52283439094 mt76: mt7915: disable UL MU-MIMO for mt7915
fd3958970e3d mt76: mt7921: enlarge maximum VHT MPDU length to 11454
18df38fe77f7 mt76: mt7915: get rid of unnecessary new line in mt7915_mac_write_txwi
149e95f5d7a6 mt76: connac: move mt76_connac_fw_txp in common module
899d192e8a79 mt76: move mt7615_txp_ptr in mt76_connac module
7184f0a6f6a5 mt76: connac: move mt76_connac_tx_free in shared code
c42d45278fa5 mt76: connac: move mt76_connac_tx_complete_skb in shared code
0993f4ef96f8 mt76: connac: move mt76_connac_write_hw_txp in shared code
467960fab791 mt76: connac: move mt7615_txp_skb_unmap in common code
2e758064b085 mt76: mt7915: rely on mt76_connac_tx_free
2065a7901671 mt76: move mcu_txd/mcu_rxd structures in shared code
576c1b7c472b mt76: move mt76_connac2_mcu_fill_message in mt76_connac module
7275f7758090 mt76: mt7915: fix incorrect testmode ipg on band 1 caused by wmm_idx
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Compiler option -no-plt will break kernel builds on some architectures
eg. (x86) Filter this option from the recently introduced handling of
KCFLAGS vs EXTRA_OPTIMISATION
Fixes: 1d42af720c ("kernel: use KCFLAGS for passing EXTRA_OPTIMIZATION flags")
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Document the ubus methods we added to hostapd so that people don't have
to read code to figure out which methods are available and what they do.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
CFE on these devices expects to find the kernel compressed with LZMA but
with no dictionnary and no loader, adjust the image generation
accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update the device databases to contain an entry for the Netgear WNR3500L
v2 router, the same buttons and LEDs mapping as v1 is used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Back port the patches being submitted upstream in order to make the NAND
controller work on BCM47187/5358. This is a prerequisite for supporting
devices like the Netgear WNR3500L V2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds a few fixes for compiling against Linux 5.10:
1. segment_eq() has been removed with upstream commit
428e2976a5bf7e7f5554286d7a5a33b8147b106a ("uaccess: remove
segment_eq") and can use uaccess_kernel() instead
2. ioremap_nocache() is removed and is now an alias for ioremap() with
upstream commit 4bdc0d676a643140bdf17dbf7eafedee3d496a3c ("remove
ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
1. KCFLAGS should be used for custom flags
2. Optimization flags are arch / SoC specific
3. -fno-reorder-blocks may *worsen* network performace on some SoCs
4. Usage of flags was *reversed* since 5.4 and noone reported that
If we really need custom flags then CONFIG_KERNEL_CFLAGS should get
default value adjusted properly (per target).
Ref: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Link: http://lists.openwrt.org/pipermail/openwrt-devel/2022-June/038853.html
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20190409093046.13401-1-zajec5@gmail.com/
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
ar9.dtsi and danube.dtsi only have one reset controller and they are
naming it "reset". This is equivalent to "reset0" in vr9.dtsi. Fix the
references to the reset controller in the recently added PCI controller
reset line.
Fixes: 087f2cba26 ("lantiq: dts: Add the reset line for the PCI controller")
Reported-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of other devices from 'ramips' target.
Fixes: #9842Fixes: #8964
Reported-by: Juergen Hench <jurgen.hench@gmail.com>
Tested-by: Juergen Hench <jurgen.hench@gmail.com>
Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This uses kernel's generic variable and doesn't require patching it with
a custom Makefile change. It's expected *not* to change any behaviour.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Existing conntracks will continue to be SNATed to 192.0.0.1 even after
464xlat interface gets teared down. To prevent this, matching
conntracks must be killed.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
ClearFog GT 8K is device sold by SolidRun. It is marketed as a
development board, not a consumer product. The device tree file for this board
is upstream in kernel.org.
Signed-off-by: Logan Blyth <mrbojangles3@gmail.com>
As per the series:
<https://www.spinics.net/lists/devicetree/msg508906.html>
"Enforce specific naming pattern for children (keys) to narrow the
pattern thus do not match other properties. This will require all
children to be properly prefixed or suffixed (button, event, switch
or key)."
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
On x86, when both CONFIG_GRUB_CONSOLE and CONFIG_GRUB_SERIAL are set (as
they are by default), the kernel command line will have two console=
entries, such as
console=tty0 console=ttyS0,115200n8
Failsafe was only running a shell on the first defined console, the VGA
console. This is a problem for devices like apu2, where there is only a
serial console and it appears on ttyS0.
Moreover, the console prompt to enter failsafe during boot was delivered
to, and its input read from, the last console= on the kernel command
line. So while the failsafe shell was on the first defined console, only
the last defined console could be used to enter failsafe during boot.
In contrast, the x86 bootloader (GRUB) operates on both the serial
console and the VGA console by virtue of "terminal_{input,output}
console serial". GRUB also provided an alternate means to enter failsafe
from either console. The presence of two console= kernel command line
parameters causes kernel messages to be delivered to both. Under normal
operation (not failsafe), procd runs login in accordance with inittab,
which on x86 specifies ttyS0, hvc0, and tty1, allowing login through any
of serial, hypervisor, or VGA console. Thus, serial access was
consistently available on x86 devices with serial consoles under normal
operation, except for shell access in failsafe mode (without editing the
kernel command line).
By presenting the failsafe prompt, reading failsafe prompt input, and
running failsafe shells on all consoles listed in /proc/cmdline,
failsafe mode will work correctly on devices with a serial console (like
apu2), and the same image without any need for reconfiguration can be
shared by devices with the more traditional (for x86) VGA console. This
improvement should benefit any system with multiple console= arguments,
including x86 and bcm27xx (Raspberry Pi).
Signed-off-by: Mark Mentovai <mark at moxienet.com>
adds `libusb-1.0.so` link on the target root again.
Fixes: 43539a6aab ("libusb: make InstallDev explicit")
Signed-off-by: Leo Soares <leo@hyper.ag>
(added fixed tag, reworded commit)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The PCI controller has it's reset line wired up to bit 13 of RCU.
Describe this in our .dtsi files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This backports encap offload support from upstream.
On some ath10k devices there can be about 10% improvement on tx throughput.
Users can turn it on by setting frame_mode=2.
Signed-off-by: Zhijun You <hujy652@gmail.com>
This adds support for the Netgear PGZNG1, also known as the ADT Pulse
Gateway.
Hardware:
CPU: Atheros AR9344
Memory: 256MB
Storage: 256MB NAND Hynix H27U2G8F2CTR-BC
USB: 1x USB 2.0
Ethernet: 2x 100Mb/s
WiFi: Atheros AR9340 2.4GHz 2T2R
Leds: 8 LEDs
Button: 1x Reset Button
UART:
Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest
to the JPE1 marking, is VCC. Note VCC isn't required to be connected
for UART to work.
Enable Stock Firmware Shell Access:
1. Interrupt u-boot and run the following commands
setenv console_mode 1
saveenv
reset
This will enable a UART shell in the firmware. You can then login using
the root password of `icontrol`. If that doesn't work, the device is
running a firmware based on OpenWRT where you can drop into failsafe to
mount the FS and then modify /etc/passwd.
Installation Instructions:
1. Interupt u-boot and run the following commands
setenv active_image 0
setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset}
setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset}
setenv bootcmd run openwrt_bootcmd
saveenv
2. boot initramfs image via TFTP u-boot
tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000
3. Once booted, use LuCI sysupgrade to
flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin
MAC Table:
WAN (eth0): xx:xa - caldata 0x0
LAN (eth1): xx:xb - caldata 0x6
WLAN (phy0): xx:xc - burned into ath9k caldata
Not Working:
Z-Wave
RS422
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(added more hw-info, fixed file permissions)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the mainline kernel module for the PCA955x
LED driver. Note this requires i2c and GPIO support. Also worth calling
out this driver also enables GPIO support, depending on device tree
configuration.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
These patches are to support the pca955x led with OpenWRT correctly via
device tree on linux 5.10. Without these, the new LED function/color/reg
features can not be used.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This row is no longer necessary as it was replaced by LOCALVERSION in
uboot.mk, which explicitly sets OpenWrt version to all U-boot packages accross
OpenWrt. [1]
[1] d6aa9d9e07
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Release notes:
https://ftp.openbsd.org/pub/OpenBSD/LibreSSL/libressl-3.4.3-relnotes.txt
```
It includes the following security fix:
* A malicious certificate can cause an infinite loop.
Reported by and fix from Tavis Ormandy and David Benjamin, Google.
```
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
If the RTC module is compiled as a module, the hctosys fails to
initialize because ds1307 is loaded later.
Fixes:
[ 2.004145] hctosys: unable to open rtc device (rtc0)
[ 11.957997] rtc-ds1307 0-006f: registered as rtc0
This is similar to commit 5481ce9a11,
which was done for imx6 target.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
The Meraki MR74 is part of the "Insect" series. This device is
essentially an outdoor variant of the MR33 with identical hardware, but
requiring a config@3 DTS option to be set to allow booting with the
stock u-boot.
The install procedure is replicated from the MR33, with the exception
being that the MR74 sysupgrade image must be used.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
The MBL has a 512KiB Microchip SST39VF040 chip for uboot and
not much else.
Thanks to Ewald who figured out that the "jedec-probe" vs.
"jedec-flash" was the wrong binding. With this information
and the jedec-probe support enabled => the chip works.
| physmap-flash 4fff80000.nor_flash: physmap platform flash device: [mem 0x4fff80000-0x4ffffffff]
| Found: SST 39LF040
| 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank
Suggested-by: Ewald Comhaire <e.comhaire@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In subtarget p2020, there wasn't enabled nand support, and because of
that there weren't available tools from mtd-utils package, which has
utilities for NAND flash memory even though reference board, which
is the only currently supported device in p2020 subtarget has NAND [1].
All subtargets in mpc85xx has already enabled nand support, let's do it
globally.
[1] https://www.nxp.com/design/qoriq-developer-resources/p2020-reference-design-board:P2020RDB
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Keeping the pvid at 0 when VLAN-unaware makes it possible to drop the
hack introduced in commit 920eaab1d8 ("kernel: DSA roaming fix for
Marvell mv88e6xxx"). Dropping the hack makes it possible to use VLAN
interfaces with VID 1 on DSA ports without problems with FDB.
Signed-off-by: Marek Behún <kabel@kernel.org>
(cherry picked from commit 9caa6f0aa7)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[drop kernel patch hack from Linux version 5.15, drop paragraph about
backport patch, which is not necessary as it is included in kernel 5.15]
with the switch to DSA setup, the switch gets correctly
programmed via the device-tree now. This hack is no
longer necessary.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linux' upstream MTD-Maintainer Miquèl Raynal noted:
|Reverting seems the safest option here, not knowing how many devices
|have these damaged/counterfeit chips. If it is just a couple and only on
|Fritzboxes, as suggested in the Github issue this patch could be
|carried through OpenWrt and that would seem more future proof IMHO.
This patch follows up with the first patch. It actually
moves the patches out of target/linux/generic/pending into
the ipq40xx's patch heap and adds a little note what happend.
For more information, discussions or reports about bad TC58NVG0S3Hs,
please visit the OpenWrt's Github Issue #9962:
<https://github.com/openwrt/openwrt/issues/9962>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Netgear GS108Tv3 is already supported by OpenWrt, but is missing LED
support. After OpenWrt installation, all LEDs are off which makes the
installation quite confusing.
This enables support for the green/amber power LED to give feedback
about the current status.
This is basically just a verbatim copy of commit c4927747d2 ("realtek:
add support for power LED on Netgear GS308Tv1").
Please note that both LEDs are wired up in an anti-parallel fashion,
which means that only one of both LEDs/colors can be switched on at the
same time. If both LEDs/colors are switched on simultanously, the LED
goes dark.
Tested-by: Pascal Ernster <git@hardfalcon.net>
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
[add title to commit reference]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash
* 16 x 10/100/1000BASE-T ports
- Internal PHY with 8 ports (RTL8218B)
- External PHY with 8 ports (RTL8218B)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6
UART pinout
-----------
[o]ooo|J6
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Boot initramfs image from U-Boot
--------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl838x-d-link_dgs-1210-20-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.
It has been developed and tested on device with F1 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct initramfs image name]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the
WPS cutton to fix button behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
4383528e0 P2P: Use weighted preferred channel list for channel selection
f2c5c8d38 QCA vendor attribute to configure RX link speed threshold for roaming
94bc94b20 Add QCA vendor attribute for DO_ACS to allow using existing scan entries
b9e2826b9 P2P: Filter 6 GHz channels if peer doesn't support them
d5a9944b8 Reserve QCA vendor sub command id 206..212
ed63c286f Remove space before tab in QCA vendor commands
e4015440a ProxyARP: Clear bridge parameters on deinit only if hostapd set them
02047e9c8 hs20-osu-client: Explicit checks for snprintf() result
cd92f7f98 FIPS PRF: Avoid duplicate SHA1Init() functionality
5c87fcc15 OpenSSL: Use internal FIPS 186-2 PRF with OpenSSL 3.0
9e305878c SAE-PK: Fix build without AES-SIV
c41004d86 OpenSSL: Convert more crypto_ec_key routines to new EVP API
667a2959c OpenSSL: crypto_ec_key_get_public_key() using new EVP_PKEY API
5b97395b3 OpenSSL: crypto_ec_key_get_private_key() using new EVP_PKEY API
177ebfe10 crypto: Convert crypto_ec_key_get_public_key() to return new ec_point
26780d92f crypto: Convert crypto_ec_key_get_private_key() to return new bignum
c9c2c2d9c OpenSSL: Fix a memory leak on crypto_hash_init() error path
6d19dccf9 OpenSSL: Free OSSL_DECODER_CTX in tls_global_dh()
4f4479ef9 OpenSSL: crypto_ec_key_parse_{priv,pub}() without EC_KEY API
b092d8ee6 tests: imsi_privacy_attr
563699174 EAP-SIM/AKA peer: IMSI privacy attribute
1004fb7ee tests: Testing functionality to discard DPP Public Action frames
355069616 tests: Add forgotten files for expired IMSI privacy cert tests
b9a222cdd tests: sigma_dut and DPP curve-from-URI special functionality
fa36e7ee4 tests: sigma_dut controlled STA and EAP-AKA parameters
99165cc4b Rename wpa_supplicant imsi_privacy_key configuration parameter
dde7f90a4 tests: Update VM setup example to use Ubuntu 22.04 and UML
426932f06 tests: EAP-AKA and expired imsi_privacy_key
35eda6e70 EAP-SIM peer: Free imsi_privacy_key on an error path
1328cdeb1 Do not try to use network profile with invalid imsi_privacy_key
d1652dc7c OpenSSL: Refuse to accept expired RSA certificate
866e7b745 OpenSSL: Include rsa.h for OpenSSL 3.0
bc99366f9 OpenSSL: Drop security level to 0 with OpenSSL 3.0 when using TLS 1.0/1.1
39e662308 tests: Work around reentrant logging issues due to __del__ misuse
72641f924 tests: Clean up failed test list in parallel-vm.py
e36a7c794 tests: Support pycryptodome
a44744d3b tests: Set ECB mode for AES explicitly to work with cryptodome
e90ea900a tests: sigma_dut DPP TCP Configurator as initiator with addr from URI
ed325ff0f DPP: Allow TCP destination (address/port) to be used from peer URI
e58dabbcf tests: DPP URI with host info
37bb4178b DPP: Host information in bootstrapping URI
1142b6e41 EHT: Do not check HE PHY capability info reserved fields
7173992b9 tests: Flush scan table in ap_wps_priority to make it more robust
b9313e17e tests: Update ap_wpa2_psk_ext_delayed_ptk_rekey to match implementation
bc3699179 Use Secure=1 in PTK rekeying EAPOL-Key msg 1/4 and 2/4
d2ce1b4d6 tests: Wait for request before responding in dscp_response
Compile-tested: all versions / ath79-generic, ramips-mt7621
Run-tested: hostapd-wolfssl / ath79-generic, ramips-mt7621
Signed-off-by: David Bauer <mail@david-bauer.net>
Downstream projects might re-generate device-specific configuration
based on OpenWrt's defaults on each upgrade, thus being unaffected by
forward- as well as backwards-breaking configuration.
Add a new sysupgrade parameter, which allows sysupgrades between minor
compat-versions. Upgrades will still fail upon mismatching major compat
versions.
Signed-off-by: David Bauer <mail@david-bauer.net>
ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration"
to load the device specific caldata, not "calibration". Rename the nvmem
cell node and label to match the updated cell name.
Fixes: eca0d73011 ("ath79: TP-Link EAP225 v3: convert ath10k to nvmem-cells")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration"
to load the device specific caldata, not "calibration". Rename the nvmem
cell node and label to match the updated cell name.
Fixes: 48625a0445 ("ath79: TP-Link EAP225-Wall v1: convert radios to nvmem-cells")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Fixes errors in the form of:
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,
vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device
=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin
from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
As described already in 2d3321619b ("ath79: TP-Link EAP245 v3: use
pre-calibration nvmem-cell"):
Ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration"
to load the device specific caldata, not "calibration".
Further rename the nvmem cell node and label to match the updated cell name.
Fixes: 23b9040745 ("ath79: TP-Link EAP225-Outdoor v1: convert ath10k to nvmem-cells")
Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Nick Hainke <vincent@systemli.org>
There is not RTC battery connected to the SoC of the UniFi 6 LR board.
Disable the RTC to prevent the system coming up with time set to
2000-01-01 00:00:00 after each reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Convert the calibration data reference for the ath9k radio to an
nvmem-cell, replacing the downstream mtd-cal-data property.
Since the 'art' label is no longer used, it can be dropped.
Cc: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The art partition containing the radio calibration data is in the same
location for all supported devices. Move the definition to the base file
so the reference from the wmac node can reference the same file.
Cc: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
