Commit Graph

119 Commits

Author SHA1 Message Date
George Oldfort
d42075dcef mediatek: improve device tree for Acer Predator Connect W6
In order to prepare for OpenWrt support other Acer W6 devices and to get
a step further to full hardware support for Acer Predator Connect W6, this
commit
- adjusts the product name ("Acer Predator Connect W6")
- updates gpio LED labels to function/color scheme
- show router status by using first rgb led instead of it's red color only
  (blue: booting/failsafe mode; red: sysupgrade; green: running – was: red)
- changes switch/eth1 led configuration to reflect RX/TX activity and speed
  (green: full 1Gbps/2.5Gbps speed; amber: lower speed; blink: RX/TX)
- shortens dummy dm-mod.create string in bootargs
- enables W6's i2c interface

This is the third of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
Romanov Danila
d8a9669093 mediatek: change Routerich AX3000 ubi size
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)

These partitions weren't used:
firmware_backup
zrsave
config2

Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 15:42:24 +01:00
Enrico Mioso
b43194e041 mediatek: filogic: add support for GatoNetworks GDSP
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.

Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
          the built-in Mediatek watchdog is also present and effective, but
          not used at the moment.

This porting has been tested only with 1x 5G modems installed (the device
supports up to two).

Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.

OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:

insmod mtd-rw i_want_a_brick=1

Then update relevant flash partitions:

mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP

And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.

Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).

U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.

MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.

device					MAC address		U-Boot env variable		factory partition offset
2.4 GHz Wi-Fi		:84						wifi_mac							0x4
5.8 GHz Wi-Fi		:85						not present						not present
WAN							:86						wan_mac								0x24
LAN							:87						lan_mac								0x2A

Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2024-11-14 04:14:23 +00:00
John Crispin
a85f11f191 mediatek: filogic: add Arcadyan Mozart platform
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 4 GiB DDR4 RAM
* 2x 10000M + 1x 1000M  ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* 2 buttons (Reset, WPS)
* 2x LED for each GMAC
* USB-C PD power input

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-01 07:43:00 +01:00
Daniel Golle
b27075e12b mediatek: add wireless offloading firmware to MT7988 boards
Install mt7988-wo-firmware by default on boards based on MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-23 13:40:09 +01:00
Daniel Golle
e550c6d381 mediatek: fix OpenWrt One ubinized image in IB
The ImageBuilder when using the profile for the OpenWrt One has been
failing because the initramfs image included in the ubinized image could
not be found.

Fix that by using the staged initramfs instead when using the
ImageBuilder.

Fixes: 797904b3cb ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-21 00:49:22 +01:00
Chukun Pan
e98987048a mediatek: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-10-15 21:36:16 +01:00
Daniel Golle
3f98f68573 mediatek: filogic: select MT7996 2+3+3 firmware
Select MT7996 2+3+3 firmware for the Adtran SmartRG SDG-8733A device
and also add it to the image for the BPi-R4 which supports both,
BE19000 (4+5+5) as well as BE14000 (2+3+3) Wi-Fi 7 modules.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-29 23:04:34 +01:00
Chris Webb
7eda44f536 uboot-mediatek: support GL.iNet GL-X3000 and GL-XE3000
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.

The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)

Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:

  https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/

The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.

http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.

Alternatively, from a root shell on the running system, unlock the boot
partition with

  echo 0 >/sys/block/mmcblk0boot0/force_ro

then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.

Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-09-22 23:50:40 +02:00
Daniel Golle
d0a2b3f824 mediatek: add Adtran SmartRG SDG-8733A
Specification is similar to other devices of the MT Stuart series:
 * Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
 * 8 GiB eMMC
 * 2 GiB DDR4 RAM
 * 2500M/1000M/100M LAN port
 * 10000M/5000M/2500M/1000M/100M/10M WAN port
 * MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
 * Renesas DA14531MOD Bluetooth
 * 2 buttons (Reset, Mesh/WPS)
 * uC-controlled RGB LED via I2C
 * 2x LED for the 2.5G port, 3x LED for the 10G port
 * 3.3V-level 115200 baud UART console via 4-pin Dupont connector
   exposed at the bottom of the device
 * USB-C PD power input

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-20 22:47:05 +01:00
Pawel Dembicki
19d770d7b9 mediatek: filogic: add support for Cudy AP3000 Outdoor
Hardware highlights:
  - MediaTek MT7981 WiSoC
  - 256MB DDR3 RAM
  - 64MB SPI-NAND
  - MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
  - 1x LED in two colors
  - 2x Button
  - 1x 1GbE
  - Two detachable antenas, two internal pcb antenas
  - PoE powered (standalone)

MAC:
LAN MAC: label mac
2.4G MAC: label mac -1
5G MAC: label mac

How to install:
1. Apply Cudy Intermediate OpenWrt image for AP3000 Outdoor V1
2. Install OpenWrt sysupgrade image

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16156
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-25 15:35:53 +02:00
Goetz Goerisch
3774f3272e treewide: rename ZyXEL to Zyxel
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.

This commit aligns the casing of Zyxel everywhere.

Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-25 15:08:25 +02:00
Chukun Pan
73832e1a48 mediatek: add support for TP-Link TL-XTR8488
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: MT40A512M16TB-062ER 1GB
  Ethernet: 2x 2.5G, 4x 1G Lan
  WiFi1: MT7976GN 2.4GHz 4T4R
  WiFi2: MT7976AN 5.2GHz 4T4R
  WiFi3: MT7915AN 5.8GHz 4T4R
  Button: Reset, WPS, Turbo
  USB: 1 x USB 3.0
  Power: DC 12V 5A

Flash instructions:
  1. Execute the following operation to open nc shell:
     https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
  2. Replace the stock bootloader to OpenWrt's:
     dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
     dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
  3. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
  4. Download the initramfs image, and restart the router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-25 22:54:16 +02:00
Rafał Miłecki
74879140a1 treewide: fixup models names for UniFi U6 series
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).

Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)

Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.

Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-07-25 11:18:25 +02:00
Luca Piccirillo
7390642237 treewide: match the COMFAST brand name across supported devices
COMFAST CF-E393AX
COMFAST CF-E390AX & CF-EW72 V2
COMFAST CF-WR617AC

Signed-off-by: Luca Piccirillo <luca.piccirillo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14690
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 18:08:49 +02:00
Tianling Shen
f2f428c699 mediatek: add ABT ASR3000 support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A

Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
     * Enter fakeroot if you are not login as root.
   base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
   ( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
   tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
   ASR3000 via telnet.

Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
   mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
   mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 16:13:06 +02:00
Dirk Buchwalder
9e49593ff7 mediatek: filogic: add support for TP-LINK RE6000XD
This commit adds support for TP-LINK RE6000XD.
The device is quite similar to the Mercusys MR90X V1,
except only 3 LAN ports and more LEDs.
So thanks to csharper2005 for doing all the groundwork.

Device specification
--------------------
SoC Type:   MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM:        MediaTek MT7986BLA (512MB)
Flash:      SPI NAND GigaDevice (128 MB)
Ethernet:   MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet:   1x2.5Gbe (LAN3 2.5Gbps), 2xGbE (LAN 1Gbps, LAN1,
            LAN2)
WLAN 2g:    MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g:    MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs:       8 LEDs, 1 status blue, 2x WIFI blue, 2x signal
	    blue/red, 3 LAN blue gpio-controlled
Button:     2 (Reset, WPS)
USB ports:  No
Power:      12 VDC, 2 A
Connector:  Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, ubi0
            partition contain "seconduboot" (also U-Boot 2022.01-rc4)

Serial console (UART), unpopulated
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |
    +--- Don't connect

Disassemble: rm the 2 screws at the bottom and the one at the backside.
            un-clip the case starting at the edge above the LEDs.

Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot openwrt-mediatek-filogic-tplink_re6000xd-initramfs-kernel.bin bootm
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Notice: while I was successfull at activating ssh (as described
        here:
        https://www.lisenet.com/2023/gaining-ssh-access-to-tp-link-re200-wi-fi-range-extender/)

        Unfortunately I haven't found the correct root password.
        Looks like they are using a static password
        (md5crypt, salt + 21 characters) that is not the web
        interface admin password.

        The TP-LINK RE900XD looks like the very same device,
        according to the pictures and the firmware.
        But I haven't checked if the OpenWrt firmware works as well
        on that device.

        The second ubi partition (ubi1) is empty and there is no known
        dual-partition mechanism, neither in u-boot nor in the stock firmware.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2024-07-04 22:14:32 +02:00
Hauke Mehrtens
5be9a8790c mediatek: Ruijie RG-X60 Pro: Add kmod-mt7915e
Add the kmod-mt7915e wifi driver to the default packages for the Ruijie
RG-X60 Pro. kmod-mt7915e has to be added recently and was not done
before merging the support for Ruijie RG-X60 Pro.

Fixes: 3de3c2bdfa ("mediatek: add support for Ruijie RG-X60 Pro")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-06-10 12:42:23 +01:00
Sijia Huang
33db914607 mediatek: filogic: Add support for Wavlink WL-WN586X3
Hardware
--------
- SOC: MediaTek MT7981
- ram: 256MB DDR3
- FLASH: 16MB SPI-NOR
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS

MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
 2G: 80:3F:5D:xx:xx:x3 partition "factory" at 0x4 (binary), on label
 5G: 80:3F:5D:xx:xx:x3 Same as 2G

Installation Method 1: ssh
--------------------------
1. Connect PC to the lan port. Set the PC IP to 192.168.10.100 if
   required.
2. Navigate to http://192.168.10.1/
3. Log into the Wavlink WebGUI. Default username/password is
   admin/admin.
4. Use WebGUI to upgrade the firmware to
   WAVLINK_WN586X3-A_M86X3A_V240113_WO-GDBYFM-modified.bin
   downloaded from
   https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
   Warning: All settings will be lost!
5. Wait about 5 minutes, and after flashing is completed, log into
   the router using (with admin123 as password):
   ssh root@192.168.10.1
6. scp the openwrt image file onto the router, usually under /tmp
   somewhere.
   openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin
7. Flash openwrt image file like so:
   mtd write \
     openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin \
     firmware
   Warning: Previous firmware will be overwritten!
8. Wait about 5 minutes, and after the flashing is completed, set
   the PC IP to 192.168.1.100 if required and log into the router
   like so:
   ssh root@192.168.1.1

Installation Method 2: u-boot
-----------------------------
1. Connect UART:  TX-> 586X3 RX, RX-> 586X3 TX, GND-> 586 GND.
2. Connect PC to the wan (not lan!) port.
3. Setup the tftp server on PC, set IP to 192.168.10.100,
4. Power on the device. Select '2' to upgrade firmware in Uboot.
5. Input the image name and start to upgrade.

Uboot console log:

CPU:   MediaTek MT7981
Model: mt7981-rfb
DRAM:  256 MiB
Core:  34 devices, 13 uclasses, devicetree: embed
Loading Environment from nowhere... OK
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address -
02:47:fb:b2:53:2d
eth0: ethernet@15100000
UBOOT WN586X3A
gpio: pin 9 (gpio 9) value is 0
gpio: pin 10 (gpio 10) value is 0
gpio: pin 5 (gpio 5) value is 0
gpio: pin 12 (gpio 12) value is 0
gpio: pin 13 (gpio 13) value is 0

  *** U-Boot Boot Menu ***

      1. Startup system (Default)
      2. Upgrade firmware
      3. Upgrade ATF BL2
      4. Upgrade ATF FIP
      5. Upgrade single image
      6. Load image
      0. U-Boot console

Co-authored-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: Sijia Huang <engineer31@win-star.com>
2024-06-09 14:58:25 +02:00
Tianling Shen
40e7fab9e4 mediatek: add Nokia EA0326GMP support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, WPS/Mesh
  Power: DC 12V 1A

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
   https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
     These binaries are extraced from the factory firmware, which are
     dynamically linked with aarch64 musl 1.1.24. To use them, you
     must run them under the same runtime environment, otherwise the
     binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
   tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
   mv mkconfig seama /bin
   chmod +x /bin/mkconfig
   chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
     Enter fakeroot if you are not login as root.
   mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
   tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
   tar -zcf backup.tar.gz etc/
   mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.

A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz

Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
   mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
   mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-06-06 18:56:32 +01:00
Ashley Lee
3de3c2bdfa mediatek: add support for Ruijie RG-X60 Pro
This pull request ports Ruijie RG-X60 Pro router support to the main branch.

Parameters:
- SoC       : MediaTek MT7986A Quad-core ARM Cortex-A53 2.0GHz
- RAM       : DDR3 512MiB (W634GU6QB)
- Flash     : SPI-NAND 128 MiB (W25N01GVZEIG)
- WLAN      : MediaTek MT7986A integration dual-band WiFi 6
  - 2.4 GHz : b/g/n/ax, MIMO 4x4
  - 5 GHz   : a/n/ac/ax, MIMO 4x4
- Ethernet  : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
                    2500Mbps x 1 (Realtek RTL8221B-VB-CG)
- UART      : through-hole on PCB
  - [J500] GND, TX, RX, 3.3V (115200n1)
- Buttons   : Mesh, Reset
- LEDs      : 1x Power (Blue)
                  1x Turbo (Purple)
- Power     : 12 VDC, 3 A

How to Installation:
1. Remove the case and connect the TTL cable to the corresponding position.
2. Power on the device and quickly press "down" on the keyboard, then
   U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Openwrt image file name to be
   flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.

How return to stock:

1. Remove the case and connect the TTL cable to the corresponding
   position.
2. Power on the device and quickly press "down" on the keyboard, then
   U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Stock “E-WEBOS” image file name to
   be flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.

About recovery:
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.

About MAC Address:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 10:82:3D:XX:XX:9E | label     |
| LAN     | 10:82:3D:XX:XX:9F | label+1   |
| WLAN 2g | 10:82:3D:XX:XX:A0 | label+2   |
| WLAN 5g | 10:82:3D:XX:XX:A1 | label+3   |
+---------+-------------------+-----------+

Signed-off-by: Ashley Lee <code@emtips.net>
2024-06-05 17:44:11 +01:00
Daniel Golle
c71b68acdd mediatek: filogic: add Adtran SmartRG Mount Stuart series
Common specifications:
 * Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
 * 8 GiB eMMC
 * 2 GiB DDR4 RAM
 * 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
 * MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
 * Airoha AG3352 GPS
 * Renesas DA14531MOD Bluetooth
 * 2 buttons (Reset, Mesh/WPS)
 * uC-controlled RGB LED via I2C
 * 2x LED for each 1G port, 3x LED for each 10G port
 * USB 3.0 type A port
 * 3.3V-level 115200 baud UART console via 4-pin Dupont connector
   exposed at the bottom of the device
 * USB-C PD power input

SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+

Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-24 18:34:13 +01:00
Rafał Miłecki
e83a5618d4 mediatek: include "kmod-mt7915e" package per device
mt7915e driver supports MT7915 & MT7916 devices and MT7981 & MT7986
on-SoC wireless controllers. Devices based on MT7988 and possibly other
next chipsets are quite unlikely to need it (MT7988 was designed to be
used with MT7996).

Move kmod-mt7915e to DEVICE_PACKAGES of relevant devices.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-05-23 12:24:48 +02:00
John Crispin
dd58ad968a mediatek/filogic: add OpenWrt One support
Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - 1GB RAM
 - 16MB NOR
 - 128MB NAND
 - 3 LEDs (red, green, blue, white)
 - 2 buttons (reset, user defined)
 - 1 2.5Gbit WAN port (Airoha EN8811h)
 - 1 1Gbit LAN ports
 - 1 single lane M.2 SSD slot
 - 1 mikroBus socket
 - externel HW WDT (25s refresh time)
 - i2c RTC (with battery backup)

Serial Interface
 - UBS-C CDC-ACM
 - 3 Pins GND, RX, TX
 - Settings: 115200, 8N1

MAC addresses are not populated on the early samples.

Signed-off-by: John Crispin <john@phrozen.org>
2024-05-21 11:35:38 +02:00
John Crispin
47d308a46c Revert "mediatek/filogic: add OpenWrt One support"
This reverts commit 797904b3cb.

There is a stray line in the commit description

Signed-off-by: John Crispin <john@phrozen.org>
2024-05-21 11:35:28 +02:00
John Crispin
797904b3cb mediatek/filogic: add OpenWrt One support
filogic: Add support for D-Link AQUILA PRO AI M30

Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - 1GB RAM
 - 16MB NOR
 - 128MB NAND
 - 3 LEDs (red, green, blue, white)
 - 2 buttons (reset, user defined)
 - 1 2.5Gbit WAN port (Airoha EN8811h)
 - 1 1Gbit LAN ports
 - 1 single lane M.2 SSD slot
 - 1 mikroBus socket
 - externel HW WDT (25s refresh time)
 - i2c RTC (with battery backup)

Serial Interface
 - UBS-C CDC-ACM
 - 3 Pins GND, RX, TX
 - Settings: 115200, 8N1

MAC addresses are not populated on the early samples.

Signed-off-by: John Crispin <john@phrozen.org>
2024-05-21 10:40:20 +02:00
Felix Fietkau
59ac0440b1 mediatek: convert mt7988a-rfb to keep bl31/uboot in UBI
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-19 09:47:04 +02:00
Leon M. Busch-George
20e4a18feb mediatek: filogic: add support for Cudy M3000 v1
Hardware:
  SoC:     MT7981b
  RAM:     256 MB
  Flash:   128 MB SPI NAND
  Ethernet:
    1x 2.5Gbps (rtl8221b)
    1x 1Gbps (integrated phy)
  WiFi:    2x2 MT7981
  Buttons: Reset, WPS
  LED:     1x multicolor

Solder on UART:
  - remove rubber ring on the bottom
  - remove screws
  - pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
  - remove the (3) screws holding the board in the frame
  - remove the board from the frame to get to the screws for the silver, flat heat shield
  - remove the (3) screws holding the heat shield
  - solder UART pins to the back of the board
    - make sure to have the pins point out on side with the black, finned heat spread
    - the markings for the pins are going to be below the silver heat shield
    - Vcc is not needed

If you don't intend on using the UART outside of the installation process, you might not
want to solder:

  - carefully scrape off the thin layer of epoxy on the holes (not the copper)
  - place your pin header with the UART attached in the holes
  - the pins, starting with the one closest to the socket:
    - Vcc (not required)
    - GND
    - RX
    - TX
  - either wedge the header or hold it with your fingers so that the pins stay in contact with the board

Installation (UART):
  - attach an Ethernet cable to the 1Gbps port (black) on the router
  - hold the reset button while powering the router
  - press CTRL-C or wait for the timeout to get to the U-Boot prompt
  - prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
  - use 'tftpboot' in the U-Boot shell to pull the image
  - boot the image using 'bootm'
  - push the ..-sysupgrade to the router using your preferred method
  - perform the upgrade with 'sysupgrade -n'

There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2024-05-11 17:18:51 +02:00
Luis Mita
63b8d98dd0 mediatek: add support for Cudy TR3000 v1
Hardware:
 - SoC: MediaTek MT7981B
 - CPU: 2x 1.3 GHz Cortex-A53
 - Flash: 128 MiB SPI NAND
 - RAM: 512 MiB
 - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
 - Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
 - USB 3.0 port
 - Buttons: 1 Reset button, 1 slider button
 - LEDs: 1x Red, 1x White
 - Serial console: internal test points, 115200 8n1
 - Power: 5 VDC, 3 A

MAC addresses:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 80:af:ca:xx:xx:x1 | label+1   |
| LAN     | 80:af:ca:xx:xx:x0 | label     |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label     |
| WLAN 5g | 82:af:ca:xx:xx:x0 |           |
+---------+-------------------+-----------+

Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.

To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.

setenv bootfile initramfs-kernel.bin
tftpboot
bootm

6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.

Signed-off-by: Luis Mita <luis@luismita.com>
2024-05-09 23:32:32 +02:00
Martin Schiller
fa804f7d0e mediatek: bpi-r4: add support for 2.5GE PoE variant
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-06 09:12:05 +02:00
Robert Marko
923d7c5531
mediatek: filogic: add support for Edgecore EAP111
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input

Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2024-04-11 13:25:11 +02:00
Daniel Golle
1ae3c53466 mediatek: filogic: switch TP-LINK XDR series to fitblk
Instead of using the deprecated FIT partition parser, use the new
fitblk driver instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-09 15:07:41 +01:00
Tianling Shen
cc6c3a6ee8 mediatek: add support for OpenEmbed SOM7981
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 256 MiB SPI-NAND, 32 GB eMMC optional
  RAM: 0.5/1 GB DDR4
  Ethernet: 1x 1GbE, 1x 2.5GbE (RTL8221B)
  WiFi: MediaTek MT7976C
  USB: 1x USB 3.0
  GPIO: 26-Pin header
  UART: 6 GND, 8 TX, 10 RX (in Pin header)
  Button: Reset, WPS
  Power: Type-C PD

Installation:
The board comes with a third-party custom OpenWrt image, you can upload
sysupgrade image via LuCI directly WITHOUT keeping configurations.

Or power on the board with pressing reset button for 5 second, then visit
http://192.168.1.1 and upload -factory.bin firmware.

Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2024-03-31 20:20:59 +02:00
Roland Reinl
29cca6cfee filogic: Add support for D-Link AQUILA PRO AI M30
Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - MT7531 switch
 - 512MB RAM
 - 128MB NAND flash with two UBI partitions with identical size
 - 1 multi color LED (red, green, blue, white) connected via GCA230718
 - 3 buttons (WPS, reset, LED on/off)
 - 1 1Gbit WAN port
 - 4 1Gbit LAN ports

Disassembly:
 - There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
 - After removing the screws, the white plastic part can be shifted out of the blue part.
 - Be careful because the antennas are mounted on the side and the top of the white part.

Serial Interface
 - The serial interface can be connected to the 4 pin holes on the side of the board.
 - Pins (from front to rear):
   - 3.3V
   - RX
   - TX
   - GND
 - Settings: 115200, 8N1

MAC addresses:
 - WAN MAC is stored in partition "Odm" at offset 0x81
 - LAN (as printed on the device) is WAN MAC + 1
 - WLAN MAC (2.4 GHz) is WAN MAC + 2
 - WLAN MAC (5GHz) is WAN MAC + 3

Flashing via Recovery Web Interface:
 - The recovery web interface always flashes to the currently active partition.
 - If OpenWrt is flahsed to the second partition, it will not boot.
 - Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
 - Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the device
 - Keep the reset button pressed until the LED blinks red
 - Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
 - Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
 - The recovery web interface always reports successful flashing, even if it fails
 - After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
 - If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
 - If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
   - Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
   - Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
   - Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.

Flashing via U-Boot:
 - Open the case, connect to the UART console
 - Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
 - Power on the device and select "7. Load image" in the U-Boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
 - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
 - Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
 - Reboot the device. OpenWrt should start from flash now

Revert back to stock using the Recovery Web Interface:
 - Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
 - Press the reset button while powering on the device
 - Keep the reset button pressed until the LED blinks red
 - Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.

Decrypting a D-Link firmware image:
 - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
 - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
 - Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
 - Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(0725091522\).bin M30A1_FW101B05\(0725091522\)_decrypted.bin

Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.

Controlling the LEDs:
 - The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
 - I didn't find any documentation or driver for it, so the information below is purely based on my investigations
 - If there is already I driver for it, please tell me. Maybe I didn't search enough
 - I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
 - The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
 - The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
 - Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
 - Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
   - A reset command (0x81 0xE4) written to register 0x00
   - A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
 - The reset command is always the same
 - In the control command
   - byte 0 is always the same
   - byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
   - byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
   - byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
   - byte 7 defines the toggling frequency (if toggling enabled)
   - byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
   - byte 12 is constant 0x87

Comparison to M32/R32:
 - The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
 - The keys are available in the GPL sources for the M32
 - The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
 - Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
 - Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
 - This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
 - I adapted the recovery image creation to also calculate the checksum over the data area
 - The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
 - The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2024-03-31 19:01:20 +02:00
Chukun Pan
4ae474afbd mediatek: filogic: add Netcore N60 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: W632GU6NB DDR3 256MB
  Ethernet: 1x 2.5G + 4x 1G
  WiFi1: MT7975N 2.4GHz 4T4R
  WiFi2: MT7975PN 5GHz 4T4R
  Button: Reset, WPS
  Power: DC 12V 2A

Flash instructions:
  1. Connect to the router using ssh or telnet,
     username: useradmin, password is the web
     login password of the router.
  2. Use scp to upload bl31-uboot.fip and flash:
     "mtd write xxx-preloader.bin spi0.0"
     "mtd write xxx-bl31-uboot.fip FIP"
     "mtd erase ubi"
  3. Connect to the router via the Lan port,
     set a static ip of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  4. Download initramfs image, reboot router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Note:
  1. Back up all mtd partitions before flashing.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-03-29 22:54:28 +01:00
Allen Zhao
640b0b79ff mediatek: filogic: add Unielec U7981-01 support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 8GB eMMC or 128 MB SPI-NAND
  RAM: 256MB
  Ethernet: 5x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset
  USB: M.2(B-key) for 4G/5G Module
  Power: DC 12V 1A
  UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | VCC RX TX GND | <= |
  |   -----------------    |
  --------------------------

The U-boot menu will automatically appear at startup, and then select
the required options through UP/DOWN Key.

NAND Flash and eMMC Flash instructions:
1. Set your computers IP adress to 192.168.1.2.
2. Run a TFTP server providing the sysupgrade.bin image.
3. Power on the router, into the U-Boot menu.
4. Select "2. Upgrade firmware"
5. Update sysupgrade.bin file name, input server IP and input device
   IP (if they deviate from the defaults)
6. Wait for automatic startup after burning

Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
2024-03-25 18:14:19 +00:00
Jean Thomas
d1016446da mediatek: Add support for GL.iNet X3000 (Spitz AX) and XE3000 (Puli AX)
The GL.iNet X3000 and XE3000 are Wi-Fi 6 5G cellular routers, based on
MediaTek MT7981A SoC. The XE3000 is the same device as the X3000,
except for an additional battery.

Specifications:
 - SoC: Filogic 820 MT7981A (1.3GHz)
 - RAM: DDR4 512M
 - Flash: eMMC 8G, MicroSD card slot
 - WiFi: 2.4GHz and 5GHz with 6 antennas
 - Ethernet:
   - 1x LAN (10/100/1000M)
   - 1x WAN (10/100/1000/2500M)
 - 5G: Quectel RM520N-GL with two nano-SIM card slots
 - USB: 1x USB 2.0 port
 - UART:
   - 3.3V, TX, RX, GND / 115200 8N1

MAC addresses as verified by OEM firmware:
vendor   OpenWrt    address     source
WAN      eth0       label       factory 0x0a (label)
LAN      eth1       label + 1
2g       phy0-ap0   label + 2   factory 0x04
5g       phy1-ap0   label + 3

Installation via U-Boot rescue:
1. Press and hold reset button while booting the device
2. Wait for the Internet led to blink 5 times
3. Release reset button
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt sysupgrade image and start upgrade
6. Wait for the router to flash new firmware and reboot

Revert to stock firmware:
1. Download the stock firmware from GL.iNet website
2. Use the method explained above to flash the stock firmware

Switch the modem network port between PCIe and USB interfaces:
1. Connect to the AT commands (/dev/ttyUSB2) port using
e.g. minicom: minicom -D /dev/ttyUSB2
2. Check the current modem mode with 'AT+QCFG="data_interface"':
  - 0,0 indicates that the network port uses the USB interface
  - 1,0 indicates that the network port uses the PCIe interface
3. Switch the active interface with:
  - 'AT+QCFG="data_interface",0,0' to use the USB interface
  - 'AT+QCFG="data_interface",1,0' to use the PCIe interface
4. Reboot

Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
2024-03-13 20:47:23 +00:00
Robert Senderek
e8f7597317 mediatek: filogic: add support for Cudy RE3000 v1
MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN

OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan    Link encap:Ethernet  HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan    Link encap:Ethernet  HWaddr 80:XX:XX:08:XX:X0
eth0      Link encap:Ethernet  HWaddr 80:XX:XX:08:XX:X0
ra0       Link encap:Ethernet  HWaddr 80:XX:XX:08:XX:X0
ra2       Link encap:Ethernet  HWaddr 82:XX:XX:28:XX:X0
rax0      Link encap:Ethernet  HWaddr 82:XX:XX:38:XX:X0
rax2      Link encap:Ethernet  HWaddr 82:XX:XX:58:XX:X0

OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan    Link encap:Ethernet  HWaddr 80:XX:XX:08:XX:X0
eth0      Link encap:Ethernet  HWaddr 80:XX:XX:08:XX:X0
phy0-ap0  Link encap:Ethernet  HWaddr 80:XX:XX:08:XX:X0
phy1-ap0  Link encap:Ethernet  HWaddr 82:XX:XX:08:XX:X1

 tftp Installation via u-boot:

Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin

write to flash via sysupgrade or gui

Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
2024-02-29 21:16:27 +01:00
Daniel Golle
85f34990d3 mediatek: include 'fitblk' package for subtargets
If selected on a per-board base, fitblk doesn't end up in initramfs
images which always only come with the subtarget's default packages.
Hence fitblk needs to be included as a default package of all
subtargets making use of fitblk instead of it being selected for
individual boards.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-26 02:13:08 +00:00
Daniel Golle
016ce30976 mediatek: filogic: bpi-r3-mini: include kmod-phy-airoha-en8811h
Include the needed Ethernet PHY driver module for the BananaPi R3 mini.

Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Reported-by: BPI forum user nezar_taima
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-17 01:30:25 +00:00
Daniel Golle
d5e2177a6b mediatek: filogic: bpi-r3-mini: fix generating ubinized image
Generate ubinized image as ARTIFACT and make use of now available
generic 'ubinize-image' build step intended for that purpose.

Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-16 05:40:17 +00:00
Daniel Golle
b03d3644cf mediatek: filogic: add BananaPi BPi-R3 mini
Hardware specification
----------------------
 SoC: MediaTek MT7986A 4x A53
 Flash: 128MB SPI-NAND, 8GB eMMC
 RAM: 2GB DDR4
 Ethernet: 2x 2.5GbE (Airoha EN8811H)
 WiFi: MediaTek MT7976C 2x2 2.4G + 3x3 5G
 Interfaces:
  * M.2 Key-M: PCIe 2.0 x2 for NVMe SSD
  * M.2 Key-B: USB 3.0 with SIM slot
  * front USB 2.0 port
 LED: Power, Status, WLAN2G, WLAN5G, LTE, SSD
 Button: Reset, internal boot switch
 Fan: PWM-controlled 5V fan
 Power: 12V Type-C PD

Installation instructions for eMMC
----------------------------------
0. Set boot switch to boot from SPI-NAND (assuming stock rom or immortalwrt
   running there).
1. Write GPT partition table to eMMC
   Move openwrt-mediatek-filogic-bananapi_bpi-r3-mini-emmc-gpt.bin to
   the device /tmp using scp and write it to /dev/mmcblk0:
    dd if=/tmp/openwrt-*-r3-mini-emmc-gpt.bin of=/dev/mmcblk0
2. Reboot (to reload partition table)
3. Write bootloader and OpenWrt images
   Move files to the device /tmp using scp:
    - openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin
    - openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip
    - openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
    - openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
   Write them to the appropriate partitions:
    echo 0 > /sys/block/mmcblk0boot0/force_ro
    dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-preloader.bin of=/dev/mmcblk0boot0
    dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
    dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb of=/dev/mmcblk0p4
    dd if=/tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb of=/dev/mmcblk0p5
    sync

4. Remove the device from power, set boot switch to eMMC and boot into
   OpenWrt. The device will come up with IP 192.168.1.1 and assume the
   Ethernet port closer to the USB-C power connector as LAN port.

5. If you like to have Ethernet support inside U-Boot (eg. to boot via
   TFTP) you also need to write the PHY firmware to /dev/mmcblk0boot1:
    echo 0 > /sys/block/mmcblk0boot1/force_ro
    dd if=/lib/firmware/airoha/EthMD32.dm.bin of=/dev/mmcblk0boot1
    dd if=/lib/firmware/airoha/EthMD32.DSP.bin bs=16384 seek=1 of=/dev/mmcblk0boot1

Installation instructions for NAND
----------------------------------
0. Set boot switch to boot from eMMC (assuming OpenWrt is installed there
   by instructions above. Using stock rom or immortalwrt does NOT work!)

1. Write things to NAND
   Move files to the device /tmp using scp:
    - openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin
    - openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
    - openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
    - openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb
   Write them to the appropriate locations:
    mtd write /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-preloader.bin /dev/mtd0
    ubidetach -m 1
    ubiformat /dev/mtd1
    ubiattach -m 1
    volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip)
    ubimkvol /dev/ubi0 -N fip -n 0 -s $volsize -t static
    ubiupdatevol /dev/ubi0_0 /tmp/openwrt-*-bananapi_bpi-r3-mini-snand-bl31-uboot.fip
    cd /lib/firmware/airoha
    cat EthMD32.dm.bin EthMD32.DSP.bin > /tmp/en8811h-fw.bin
    ubimkvol /dev/ubi0 -N en8811h-firmware -n 1 -s 147456 -t static
    ubiupdatevol /dev/ubi0_1 /tmp/en8811h-fw.bin
    ubimkvol /dev/ubi0 -n 2 -N ubootenv -s 126976
    ubimkvol /dev/ubi0 -n 3 -N ubootenv2 -s 126976
    volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb)
    ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
    ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-initramfs-recovery.itb
    volsize=$(wc -c < /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb)
    ubimkvol /dev/ubi0 -n 4 -N recovery -s $volsize
    ubiupdatevol /dev/ubi0_4 /tmp/openwrt-*-bananapi_bpi-r3-mini-squashfs-sysupgrade.itb

3. Remove the device from power, set boot switch to NAND, power up and
   boot into OpenWrt.

Partially based on immortalwrt support for the R3 mini, big thanks for
doing the ground work!

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
1e58ce7652 firmware: package firmware for built-in 2.5G PHY on MT7988
Firmware for the built-in 2.5G Ethernet PHY of the MediaTek MT7988 SoC
is now part of linux-firmware, so we can package it.
Only a single file is needed with recent driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
61137a8895 mediatek: BananaPi BPi-R3 bootloader update
* Switch to all-UBI layout on SPI-NAND
 * use fitblk driver instead of uImage.FIT partition parser
 * adapt sysupgrade
 * bump COMPAT_VERSION

Remove BROKEN mark now that all needed changes are done.

Boards running images generated before this commit will require
full reflash of the bootloader, re-install from SD card is the
easiest way to achieve that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
188a1a8d67 mediatek: prepare BananaPi BPi-R3 for upcoming modernization
Mark board as broken until the complete boot stack has been updated.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
f16dc4b42f mediatek: add support for BananaPi BPI-R4 board
Hardware
--------
SOC:    MediaTek MT7988A (4x Cortex-A73)
RAM:    4 GiB DDR4
Flash:  128 MiB Winbond SPI-NAND
MMC:    8 GiB eMMC *or* microSD (cannot be used both)
ETH:    4x 1GE (1x WAN, 3x LAN)
        2x SFP+ (10G, 5G, 2.5G, 1G)
USB:    on-board USB 3.2 4-port hub
        1x USB 3.2 port (type A connector)
        1x M.2 for 4G/5G modem
        2x mPCIe for additional modems
WiFi:   optional MediaTek MT7996 Wi-Fi 7 module
        (using 2x PCIe gen3 x2 on the mPCIe slots and 12V power)

Installation
------------
1. Decompress and write the sdcard image to a micro SD card and use that
to boot the R4 (both dip switches in upper position).

2. Use the bootloader menu accessible via the serial console to install
to SPI-NAND.

3. Switch to boot from SPI-NAND and install to eMMC.

Known issues
------------
 - The RST button is hard-wired to the SoC reset and can't be read
   from software. This can be changed by modifying the board (ie.
   moving a 0-ohm resistor). However, in order to maintain compatibility
   with the board as it comes from factory the button isn't used by
   OpenWrt and the WPS button is used as factory/reset button instead.

 - various small things still need to be fixed in DT

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
David Bentham
d8f4453bf2 mediatek: add Comfast CF-E393AX support
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.

Oem firmware is a custom openwrt 21.02 snapshot version.

We can gain access via ssh once we remove the root password.

Hardware specification:
  SoC: MediaTek MT7981A 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB DDR3
  Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
            1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976D
  LEDS: 1x (Red, Blue and Green)
  Button: Reset
  UART: 3.3v, 115200n8
  --------------------------
  | Layout |
  | ----------------- |
  | 4 | VCC GND TX RX | <= |
  | ----------------- |
  --------------------------

Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
   and download the
   configuration(http://apipaddress/computer/config.html).

2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
   Enter 'fakeroot' command then decompress the configuration:
   tar -zxf backup.tar.gz

3. Edit 'etc/shadow', update (remove) root password:
   With password =
   'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
   'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
   to
   Without password =
   'root::0:99999:7:::'
   'root::0:99999:7:::'

4. Repack 'etc' directory back to a new backup file:
   tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
   Exit fakeroot - 'exit'

6. Upload new configuration via web interface, now you
   can SSH with the following:

   'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
   -o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.

   Backup the mtd partitions
   - https://openwrt.org/docs/guide-user/installation/generic.backup

7. Copy openwrt factory firmware to the tmp folder to install via ssh:

   'scp -o HostKeyAlgorithms=+ssh-rsa \
   -o PubkeyAcceptedAlgorithms=+ssh-rsa \
   *-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
   root@192.168.10.1:/tmp/'

   'sysupgrade -n -F \
   /tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'

8. Once led has stopped flashing - Connect via ssh with the
   default openwrt ip address - 'ssh root@192.168.1.1'

9. SSH copy the openwrt sysupgrade firmware and upgrade
   as per the default instructions.

Signed-off-by: David Bentham <db260179@gmail.com>
2024-02-02 13:01:38 +01:00
Chuanhong Guo
1b7e62b20b mediatek: drop NMBM layout for Xiaomi WR30U
This reverts commit dcdcfc1511.

This is a firmware for third-party u-boot mod, which should not
be carried here by us.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2024-01-23 19:24:32 +08:00
Tianling Shen
c0c3234e17 mediatek: add support for JDCloud RE-CP-03
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: 128GB eMMC
  RAM: 1GB DDR4
  Ethernet: 4x 1GbE, 1x 2.5GbE (RTL8221B)
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Joylink
  Power: DC 12V 2A

Flash instructions:
1. Download and flash the vendor migration firmware via webUI:
   https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin
   (Default address is 192.168.68.1, user root, no password)
2. After device has booted up, write new GPT table:
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-01-19 21:43:32 +01:00
Leon M. Busch-George
b4086f44cd mediatek: add support for YunCore AX835
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 16MB NOR
  RAM: 256MB
  Ethernet: 2x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset
  Power: DC 12V 1A, PoE 802.3af 48V

Flash instructions:

Option #1 - SSH

  I was able to SSH into the stock firmware of my device.

  1. Attach the router to the network
  2. Use scp (-O) to copy the sysupgrade image
  3. Connect using SSH and run `sysupgrade -n`

Option #2 - U-Boot

  One way to use the bootloader for flashing is using TFTP:

  1. Connect to the router using an ethernet cable
  2  Spin up a TFTP server serving the sysupgrade file
  3. Open the case and attach a UART
  4. Attach power to the router and interrupt the countdown by pressing
     any key
  5. Select option #2 (Upgrade firmware)
  6. Enter IP address information and image name
  7. Wait patiently

Co-Authored-By: Enrique Rodríguez Valencia <enrique.rodriguez@galgus.net>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2024-01-09 00:27:23 +01:00