Commit Graph

59036 Commits

Author SHA1 Message Date
Rosen Penev
10b7e2d0df
apm821xx: convert to nvmem-layout
nvmem-cells is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 22:50:32 +01:00
Hauke Mehrtens
d99aed31a0 mediatek: filogic: Fix GPIOs for Zbtlink ZBT-Z8102AX
The PGIO configuration should be added for the ZBT-Z8102AX and not the ZBT-Z8103AX

Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-11-25 22:25:42 +01:00
Xiaobo Liu
5fbb1f09ca ramips: mt76x8 add support for RTC class/drivers
This commit adds support for RTC class/drivers to the mt76x8 target.

Signed-off-by: Xiaobo Liu <cppcoffee@gmail.com>
2023-11-25 18:16:46 +01:00
Rosen Penev
8a8d68cf03 f2fs-tools: avoid dead symlinks in root
When building on the host, this avoids creating dead symlinks. Matches
what is done elsewhere.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-25 17:55:03 +01:00
Darlan Pedro de Campos
2a0c9cc8cd ramips: add support for TP-Link EX220 v1
This device is very similar, if not identical, to the TP-Link AX23 v1
but is targeted at service providers and features a completely different
flash layout.

Hardware
--------

CPU:    MediaTek MT7621 DAT
RAM:    128MB DDR3 (integrated)
FLASH:  16MB SPI-NOR
WiFi:   MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
        LEDs - (3V3 - GND - RX - TX) - ETH ports

Installation
------------

Flashing is only possible via a serial connection using the sysupgrade
image; the factory image must be signed. You can flash the sysupgrade
image directly through the U-Boot console, or preferably, by booting the
initramfs image and flashing with the sysupgrade command. Follow these
steps for sysupgrade flashing:

1. Establish a UART serial connection.
2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
   there.
3. Power on the device and press any key to interrupt normal boot.
4. Load the initramfs image using tftpboot.
5. Boot with bootm.
6. If you haven't done so already, back up all stock mtd partitions.
7. Copy the sysupgrade image to the router.
8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
   not to attempt saving settings.

Revert to stock firmware
------------------------

Flash stock firmware via OEM web-recovery mode. If you don't have access
to the stock firmware image, you will need to restore the firmware
partition backed up earlier.

Web-Recovery
------------

The router supports an HTTP recovery mode:

1. Turn off the router.
2. Press the reset button and power on the device.
3. When all LEDs start flashing, release reset and quickly press it
   again.

The interface is reachable at 192.168.0.1 and supports installation of
the OEM factory image. Note that flashing OpenWrt this way is not
possible, as mentioned above.

Signed-off-by: Darlan Pedro de Campos <darlanpedro@gmail.com>
2023-11-25 16:14:32 +01:00
Michael Trinidad
2ed358180e mwlwifi: update to version 10.4.10-20231120
Upstream PR 416 improvements:
 -AMPDU Optimization of priority calculation. (8864/8897)
 -8864/8897 fix wpa3
 -Add cypher suite to driver capabilities (all chip)
 -Alignment of pcie_tx_ctrl* (all chip)
 -"feature" normalization for all chips (all chip)
 -Add modprobe parameters (all chip)
 -fix monitoring (all chip)
 -Code separation by chipset (8864/8897 <=> 8997)
 -dump_prob decommissioning (8864/8897/8997)
 -fix amsdu high ping latency (8864/8897/8997)
 -drop debug info in hostcmd_get_hw_spec() (8864/8897)
 -Add wcb_base in debug info (8864)
 -Rewrite AMSDU packets (8864/8897/8997)
 -debug rewrite output mwl_debugfs_sta_read (all chip)
 -Improved encryption interoperability (8864/8897/8997)
 -factorization encrypted packet test (8864/8897/8997)
 -Change 88W8864 firmware to 7.2.9.27 (8864/8897)
 -Fix the AMPDU session lifecycle (8864/8897/8997)
 -Remove the tx done packets mechanism (8864/8897)

Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
2023-11-25 16:02:27 +01:00
Filip Milivojevic
288738c59d ramips: Add support for Cudy WR1300 v3
Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7613BE
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Buttons: Reset, WPS
 - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
 - Power: DC 12V 1A tip positive

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Cudy WR1300 v3 differs from v2 only in swapped WiFi chip PCIe slots. Common
nodes are extracted to .dtsi and new v2 and v3 dts are created.

Cudy WR1300 v2 dts now contains ieee80211-freq-limit and has
eeprom_factory_8000 length fixed.

The same manufacturer's built OpenWRT image is provided for both v2 and v3
devices as a step in installing, but for proper WiFi functionality,
a separate build is required.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

Signed-off-by: Filip Milivojevic <zekica@gmail.com>
2023-11-25 15:48:41 +01:00
Nicolò Veronese
2a0805fd3d uboot-envtools: add support for Zyxel EX5601-T0 ubootmod
The ubootmod bootlaoder for EX5601-T0 uses two partitions
 in ubi to store enviroment variables. so proper config
 is needed.

Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2023-11-25 14:51:21 +01:00
Valerio 'ftp21' Mancini
b5df398a36 mediatek: add Zyxel EX5601-T0 with uboot custom partition
The flash procedure is similar to the Xiaomi AX6000 router.

Load openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb from original Zyxel U-Boot:

tftpboot openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
bootm 0x46000000
Load mtd-rw
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

Format ubi and create ubootenv partitions

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
Copy openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb to /tmp and create recovery partition.
If your recovery image is larger than 10MiB, size the recovery partition accordingly to make it fit.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2  openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-recovery.itb
Copy preloader and uboot to /tmp and write them in the mtd

mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Now write the firmware:
sysupgrade -n  /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-squashfs-sysupgrade.itb

To create a correct BL2, I had to add a profile for 'spim:4k+256' as I could not find a way to value the variable 'NAND_TYPE'.

Features and fixes from hitech95 tree has been squashed, I'm attaching his commit message:

The Power LED was not working correctly and not reacting
 to the boot process and statuses.

The board has space (footprint) for an unpopulated Zigbee chip,
 while we dont know the device model having this chip populated
 we have to assure that the common dts doesnt enable
 interfaces that share pins with such device.

In this instance the PCIe and the uart1 and uart2 are disabled.
Some of the control PCIE pins seems to be used for the Zigbee chip,
 UART1 seems to be used as a flash port while UART2 should be the
 main comunication interface of Zigbee chip.

The Zigbee chip should be a EFR32MG21. But the pins used for UART
 seems to be not on standard PINS used by other adapters.
 So it cannot run firmwares shared on the web.
 But it should be possible to build a custom firmware with
 the corrtect pinmux.

This commit also contains the following squashed commit from hitech95
 - mediatek: fix sysupgrade for Zyxel EX7601-T0 ubootmod

Changes and fixes added in common board:
 - added aliases for boot status leds.
 - added aliases for the mac-label-device.
 - added pin claims for core features (MDIO and UART 0)
 - added default LEDs configuration (01_leds)
 - added default network configuration (02_network)
 - added missing kmod-usb3 module for USB3
 - fixed LED names
 - fixed reset pin for SLIC chip
 - removed unused pinmux configurations and devices
 - fix LAN (switch) port numbering
 - using nvmem cells for wifi eeprom, dropping deprecated "mediatek,mtd-eeprom"
 - proper factory partition and mac address handling
 - cleaned up spi_nand sections and partition

Changes and fixxes added in stock layout:
 - added NMBM, if u-boot has it, the kernel must be informed.

Co-authored-by: Nicolò Veronese <nicveronese@gmail.com>
Co-developed-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
2023-11-25 14:51:21 +01:00
Valerio 'ftp21' Mancini
a9cf87027e uboot-mediatek: add initial Zyxel EX5601-T0 support
Flash procedure is described in next commit.

TLDR:
Copy preloader and uboot to /tmp and write them in the mtd.
This will also require new UBI partition and
 volumes to boot openwrt.

mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip

Changelist:
 - Added profile for 4k+256 SPI NAND_TYPE
 - Added basic Zyxel EX5601-T0 uboot profile

Backported from hitech95 branch:
 - Button RESET pin fix
 - Button WPS pin fix

Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2023-11-25 14:51:21 +01:00
Daniel Golle
1b70025ad1 mediatek: remove DTS property added by mistake
Remove bogus 'phy-handle = <&phy0>;', an undefined reference.

Fixes: c8c2f52262 ("mediatek: add support for Zbtlink ZBT-Z8102AX")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-25 03:22:47 +00:00
Mikhail Zhilkin
1b091311aa ramips: add support for Sercomm CPJ routers
This commit adds support for following wireless routers:
 - Rostelecom RT-FL-1 (Serсomm RT-FL-1)
 - Rostelecom S1010 (Serсomm S1010.RT)

The devices are almost identical and the only difference is one bit in the
factory image PID (thanks to Maximilian Weinmann <x1@disroot.org>
(@MaxS0niX) for the info and idea to make one PR for two devices at once).

Devices specification
---------------------
   SoC:          MediaTek MT7620A, MIPS
   RAM:          64 MB
   Flash:        16 MB SPI NOR
   Wireless 2.4: MT7620 (b/g/n, 2x2)
   Wireless 5:   MT7612EN (a/n/ac, 2x2)
   Ethernet:     5xFE (WAN, LAN1-4)
   BootLoader:   U-Boot
   Buttons:      2 (wps, reset)
   LEDs:         1 amber and 1 green status GPIO leds
                 5 green ethernet GPIO leds
                 1 green GPIO 2.4 GHz WLAN led
                 1 green PHY 5 GHz WLAN led
                 1 green unmanaged power led
   USB ports:    No
   Power:        12 VDC, 1 A
   Connector:    Barrel

OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
   before file extension)
2. Upload and update the firmware via the original web interface
3. Wait until green status led stops blinking (can take several minutes)
4. Login to OpenWrt initramsfs. It's recommended to make a backup of the
   mtd partitions at this point.
4. Perform sysupgrade using the following command (or use Luci):
   sysupgrade -n sysupgrade.bin
5. Wait until green status les stops blinking (can take several minutes)
6. Mission acomplished

Return to Stock
---------------
Option 1. Restore firmware Slot1 from a backup (firmware2.bin):
   cd /tmp
   mtd -e Firmware2 write firmware2.bin Firmware2
   printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
   reboot

Option 2. Decrypt, ungzip and split stock firmware image into the parts,
take Slot1 parts (kernel2.bin, rootfs2.bin) and write them:
   cd /tmp
   mtd -e Kernel2 write kernel2.bin Kernel2
   mtd -e RootFS2 write rootfs2.bin RootFS2
   printf 1 | dd bs=1 seek=$((0x18007)) count=1 of=/dev/mtdblock2
   reboot
More about stock firmware decryption:
Link: https://github.com/Psychotropos/sercomm_fwutils/

Debricking
----------
Use sercomm-recovery tool. You can use "ALL" mtd partition backup as a
recovery image.
Link: https://github.com/danitool/sercomm-recovery

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| label   | 48:3e:xx:xx:xx:1e | label     |
| LAN     | 48:3e:xx:xx:xx:1e | label     |
| WAN     | 48:3e:xx:xx:xx:28 | label+10  |
| WLAN 2g | 48:3e:xx:xx:xx:20 | label+2   |
| WLAN 5g | 48:3e:xx:xx:xx:24 | label+6   |
+---------+-------------------+-----------+

Co-authored-by: Vadzim Vabishchevich <bestmc2009@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-25 01:11:18 +01:00
Mikhail Zhilkin
25bab2b8bc ramips: mt7620: drop unnecessary trailing tabs
Let's tidy up a bit (drop unnecessary trailing tabs).

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-25 01:11:18 +01:00
Mikhail Zhilkin
e900c45211 ramips: sercomm.mk: make common recipe to set a bit in pid
This commit makes a common recipe to set bit in Sercomm factory pid since
this is necessary for several devices (WiFire S1500.nbn, Rostelecom
RT-FL-1) at different offsets.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-25 01:11:18 +01:00
Mikhail Zhilkin
28d32244e1 scripts: sercomm-pid.py: use uppercase hwid in pid
Sercomm uses uppercase for hexadecimal representation of the device
hardware IDs in factory image PID. This commit brings the sercomm-pid.py
script into compliance with the original Sercomm algorithm.

Example
-------
+--------+-------------+-----------+-------------+
| Device | PID (before | PID       | PID (after  |
| HWID   | the commit) | (Sercomm) | the commit) |
+--------+-------------+-----------+-------------+
| CPJ    | 43 50 4a    | 43 50 4A  | 43 50 4A    |
+--------+-------------+-----------+-------------+

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-25 01:11:18 +01:00
Jitao Lu
58df088d75 linux-firmware: intel: add firmware for AX101
iwlwifi from 6.5 supports API version up to 83, but 81 is the latest one
available from linux-firmware 20230804.

Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
2023-11-25 00:39:11 +01:00
Robert Marko
5dae4a6aba ipq40xx: refresh patches
CI reported that ipq40xx needed a refresh, so lets refresh it.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-11-25 00:12:01 +01:00
Daniel Golle
c8c2f52262 mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-24 21:28:35 +00:00
Christian Marangi
6f5c301eab
generic: 6.1: backport upstream Aquantia PHY firmware loader patches
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.

Refresh all kernel patches affected by this change.

Also update the path for aquantia .ko that got moved to dedicated
directory upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-11-24 16:46:50 +01:00
Rosen Penev
d1b5981038
realtek: convert to nvmem-layout
nvmem-cells is deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-24 16:37:02 +01:00
John Audia
df167450a5 kernel: bump 5.15 to 5.15.139
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.139

Removed upstreamed:
	backport-5.15/830-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch[1]
	backport-5.15/830-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch[2]
	x86/patches-5.15/120-hwrng-geode-fix-accessing-registers.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=aec3706971b332af8321b2beccba981b8061489a
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=893eedf596dd81c7a7f0cd80b345956ae000eab9
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.139&id=a5c83c8043d70b9a28d1bd78a2dbbab340f43889

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-23 22:55:55 +01:00
John Audia
2b75f108fb kernel: bump 6.1 to 6.1.63
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.63

Removed upstreamed:
	generic/backport-6.1/815-v6.6-2-leds-turris-omnia-Drop-unnecessary-mutex-locking.patch
	generic/backport-6.1/815-v6.7-1-leds-turris-omnia-Do-not-use-SMBUS-calls.patch
	ixp4xx/patches-6.1/0007-watchdog-ixp4xx-Make-sure-restart-always-works.patch

Manually rebased:
	bcm27xx/patches-6.1/950-0606-hwrng-bcm2835-sleep-more-intelligently.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=7d0e60e4ff840e97fb18afb2a7344442c10a6fdf
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=63cdeb20ee3bfef820b045b8d3b8395f9f815a74
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.63&id=8803da01fe1b4ca3d37745283f7e73c6c2558c0c

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-23 22:51:52 +01:00
Daniel Linjama
a39a49e323 ath79: add support for D-Link COVR-P2500 A1
Specifications:
* QCA9563, 16 MiB flash, 128 MiB RAM, 2T2R 802.11n
* QCA9886 2T2R 801.11ac Wave 2
* QCA7550 Homeplug AV2 1300
* AR8337, 3 Gigabit ports (1, 2: LAN; 3: WAN)

To make use of PLC functionality, firmware needs to be
provided via plchost (QCA7550 comes without SPI NOR),
patched with the Network Password and MAC.

Flashing via OEM Web Interface
* Flash 'factory.bin' using web-interface
* Wait until firmware succesfully installed and device booted
* Hold down reset button to reset factory defaults (~10 seconds)

Flashing via Recovery Web Interface:
* Hold down reset button during power-on (~10 seconds)
* Recovery Web UI is at 192.168.0.50, no DHCP.
* Flash 'recovery.bin' with
  scripts/flashing/dlink_recovery_upload.py
  (Recovery Web UI does not work with modern OSes)

Return to stock
* Hold down reset button during power-on (~10 seconds)
* Recovery Web UI is at 192.168.0.50, no DHCP.
* Flash unencrypted stock firmware with
  scripts/flashing/dlink_recovery_upload.py
  (Recovery Web UI does not work with modern OSes)

Co-developed-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Signed-off-by: Daniel Linjama <daniel@dev.linjama.com>
2023-11-23 00:26:28 +01:00
Hauke Mehrtens
77368ec01b firmware-utils: Fix PKG_MIRROR_HASH
This fixes the mirror hash to the version of the file uploaded to the
download mirror and which my build calculated.

Fixes: b117e7244f ("firmware-utils: update to Git HEAD (2023-11-21)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-11-23 00:17:23 +01:00
Hauke Mehrtens
86994e1b78 tools: firmware-utils: Fix PKG_MIRROR_HASH
This fixes the mirror hash to the version of the file uploaded to the
download mirror and which my build calculated.

Fixes: 59a66d3c9b ("firmware-utils: update to Git HEAD (2023-11-21)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-11-23 00:16:56 +01:00
Rosen Penev
944d3526a3
mvebu: remove mac-address-increment
It's deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-22 19:58:22 +01:00
Rani Hod
aaeb379023 mediatek: fiilogic: device tree switch@1f fix
Quite a few `fiilogic` devices use the `mt7531` switch.
Some of them have a DT node that looks like:
```
switch: switch@0 {
	compatible = "mediatek,mt7531";
	reg = <31>;
...
};
```
This commit changes the DT node name to `switch@1f`.

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-22 19:42:23 +02:00
Rosen Penev
d44c037a59
ipq806x: add missing interrupt-controller
Fixes dtc warnings

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-22 00:10:31 +01:00
Rosen Penev
d264d3a60e
ipq806x: remove mac-address-increment
It's deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-22 00:10:30 +01:00
Rosen Penev
659f2d77ce
lantiq: remove mac-address-increment
It's deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-22 00:05:34 +01:00
Rosen Penev
28a3dab2ab
bmips: remove mac-address-increment
It's deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-22 00:02:01 +01:00
Christian Marangi
7993a288f1
Revert "mpc85xx: replace user space MAC with nvmem"
This reverts commit 931fcf6189.

The definition is wrong and require mac-base compatible. Also it's not
clear if it's correct to use 0xc for mac size.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-11-21 23:57:44 +01:00
Rosen Penev
931fcf6189
mpc85xx: replace user space MAC with nvmem
Possible now that NVMEM supports ASCII.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-21 23:10:18 +01:00
Rosen Penev
ddbe732357
mpc85xx: remove mac-address-increment
It's deprecated

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-21 23:10:17 +01:00
Rosen Penev
2ed2b8b16c
mpc85xx: fix dtc warning
States to remove the linux prefix

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-21 23:10:17 +01:00
Rosen Penev
733a99d824
octeon: remove mac-address-increment
It's deprecated.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-11-21 23:07:18 +01:00
Rafał Miłecki
59a66d3c9b firmware-utils: update to Git HEAD (2023-11-21)
12bf1a9 lxlfw: support certificate & signature blobs
eaf2ea2 lxlfw: support extracting image
d770cab lxlfw: support embedding blobs
16fa890 lxlfw: fix struct lxl_hdr attribute
8e149e4 lxlfw: move code copying data to helper function
3b114de lxlfw: move code opening LXL to helper function

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-11-21 21:17:29 +01:00
Rafał Miłecki
011e35e5d9 kernel: drop "mac-address-increment-byte" DT property support
This downstream DT property is not used by any DTS file anymore.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-11-21 16:34:00 +01:00
Rafał Miłecki
b117e7244f firmware-utils: update to Git HEAD (2023-11-21)
1d42292d8063 tplink-safeloader: Add TP-Link Archer A6 V3.20
3338f5389d72 tplink-safeloader: add TL-WPA8635P v3
17ca5eeb1c10 tplink-safeloader: add TL-WPA8631P v4
f730ad2fa0b4 bcmblob: new tool for reading Broadcom's BLOBs
cb1ddac98124 firmware-utils: fix typo in error message when no OpenSSL library found
916633160dc9 bcmclm: new tool for reading Broadcom's CLM data
a2d49fb1e188 tplink-safeloader: add RU support-list entry for Archer C6U v1
bb12cf5c3fa9 tplink-safeloader: Add support for TP-Link Deco M5 The special_id values are the same for EU and Asian models, and they apply to all models: v1, v2, and v3. They are not sorted as they are currently in the same order as extracted from the official firmware image.
9e2de8515be1 tplink-safeloader: add EAP610 v3 and EAP613 v1
a170683c0e11 firmware-utils: fix use of NULL string progname
89875fc18b57 tplink-safeloader: CPE510: add Canadian support
9e211d2980fe mktplinkfw2: add support to extract bootloader images
c18f662f3c74 mktplinkfw2: add support to pack bootloader
3dc133915f87 mktplinkfw2: show exact exceed bytes when the image is to big
d16ff798d58a tplink-safeloader: WPA8631: add v4 AU, US
0fa1cc51013f zytrx: add LTE5398-M904
635466123429 firmware-utils: ptgen: add SiFive GPT partition support
ba5bc4e1ae9d add dlink-sge-image for D-Link devices by SGE
3b114de29cf7 lxlfw: move code opening LXL to helper function
8e149e480391 lxlfw: move code copying data to helper function
16fa89076122 lxlfw: fix struct lxl_hdr attribute
d770cab82e58 lxlfw: support embedding blobs
eaf2ea28dbe6 lxlfw: support extracting image
12bf1a99bd6e lxlfw: support certificate & signature blobs

Fixes: https://github.com/openwrt/openwrt/issues/12939
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-11-21 16:33:27 +01:00
Felix Fietkau
0f283ab4c9 umdns: update to Git HEAD (2023-11-21)
9040335e102b interface: fix interface memory corruption
b1e023eda358 add udebug support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-11-21 07:36:08 +01:00
Felix Fietkau
33f4013bf2 udebug: update to Git HEAD (2023-11-20)
759d9404034b ring: add missing fread return code check

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-11-20 23:03:48 +01:00
Felix Fietkau
cafb961850 netifd: update to Git HEAD (2023-11-20), adds udebug support
9dcc37a77cb2 add udebug support
525fa911e8ab replace DPRINTF calls with D(...)
7642eaba3838 system-linux: fix bogus debug error messages on adding bridge members
f3e06e81b347 wireless: add bridge_isolate option

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-11-20 19:18:06 +01:00
Daniel Golle
2634d3f855 uboot-envtools: add settings for Synology DS213j
Add settings to be able to access the U-Boot environment on the
Synology DS213j NAS.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-20 13:40:17 +00:00
Daniel Golle
3f7637b050 mvebu: add support for Synology DS213j
The Synology DS213j is a rather dated dual-bay SATA NAS based on on the
Marvell Armada-370 SoC. It has long been supported in vanilla Linux,
however, flash partitioning there didn't match with reality (ie. the
bootloaders expectations) and nobody cared to wrap up OpenWrt support
for the device.

CPU: Marvell Armada-370 ARMv7 SoC @ 1200 MHz
RAM: 512 MB DDR3
Flash: 8 MB (Micron Technology N25Q064)
Network: 1x 1000M/100M/10M Ethernet (Marvell 88E1510)
SATA: 2x 3.0Gbps
USB: 2x USB 2.0

As OS options are becoming limited on that still quite useful hardware,
patch the flash partitions to be able to get the most out of it when
using OpenWrt.

The vendor firmware loads kernel and initrd from fixed addresses in
the flash, not making use of a modifyable environment stored in flash
which is stored at a location right in the middle of the vendor's
zImage partition (at 0x100000).

Stock firmware flash layout:

0x000000 ~ 0x0c0000 : "RedBoot" (actually U-Boot)
0x0c0000 ~ 0x390000 : "zImage"
0x390000 ~ 0x7d0000 : "rd.gz"
0x7d0000 ~ 0x7e0000 : "vendor" (contains MAC address, serial no)
0x7e0000 ~ 0x7f0000 : "RedBoot Config" (unused? legacy left-over)
0x7f0000 ~ 0x800000 : "FIS directory" (unused? legacy left-over)

OpenWrt flash layout:

0x000000 ~ 0x0c0000 : "u-boot"
0x0c0000 ~ 0x100000 : "gap"
0x100000 ~ 0x110000 : "u-boot-env"
0x110000 ~ 0x7d0000 : "kernel"
0x7d0000 ~ 0x7e0000 : "vendor" (contains MAC address, serial no)
0x7e0000 ~ 0x800000 : "gap2"

"kernel", "gap" and "gap2" are concatenated using the mtd-concat
virtual MTD driver, resulting in a partition "firmware" used by
OpenWrt for kernel, rootfs and rootfs-overlay, 0x720000 (7296kiB) in
total.

Installation:
1. Connect to internal serial console port and Ethernet port,
   providing a TFTP server at a static IPv4 address, e.g.
   192.168.1.254/24.
2. Interrupt bootloader using CTRL+C
3. Configure bootloader to load OpenWrt on future boot:
   setenv bootcmd "bootm f4110000"
   saveenv
4. Load and boot initramfs image via TFTP:
   setenv ipaddr 192.168.1.1
   setenv serverip 192.168.1.254
   tftpboot openwrt-mvebu-cortexa9-synology_ds213j-initramfs-kernel.bin
   bootm
5. Use sysupgrade to load final image.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-20 13:24:06 +00:00
Felix Fietkau
2723f16dda hostapd: add missing acl entries for udebug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-11-20 14:10:27 +01:00
Felix Fietkau
4cd31d6c7c ubus: update to Git HEAD (2023-11-14)
b3e8c4ef07eb Add auto subscribe support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-11-20 14:10:24 +01:00
Felix Fietkau
effc305cda hostapd: add udebug support
This is not activated by default and must be explicitly enabled via ubus
It supports reporting log messages and netlink packets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-11-20 11:58:54 +01:00
Felix Fietkau
bc6ee34c97 udebug: add new package
This will help with debugging by providing system wide access to per-process
ring buffers with debug data.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-11-20 11:58:47 +01:00
Rani Hod
c4fe1bfc65 ramips: D-Link Dxx-1xx0 image fixes
Three fixes for D-Link DAP-1620 rev B and its twin D-Link DRA-1360:

1. `uboot-envtools` is removed from default package list.
2. Makefile variable is doubly escaped, i.e. `$$$$(DLINK_HWID)`.
3. Previously the size of `factory.bin` was always 10.5 MiB, same as
D-Link firmwares. This commit makes it possible to use smaller images
(with no lost space due to padding) as well as larger images. Tested
successfully flashing a 6.5 MiB image and a 14.5 MiB image.

Recall that factory images need to be installed via D-Link Web Recovery
(at http://192.168.0.50/, server ignores pings and DHCP requests).

P.S.
I implemented the OEM firmware encryption algorithm, so firmware can be
flashed via OEM firmware, but after successful flashing the device
reboots to web recovery, so further debugging is required.

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-20 00:24:54 +01:00
Carter Wang
df4c5f7eb2 uboot-mediatek: Fix ubi command in uboot commands
Fix typo 'ubi remote ...' -> 'ubi remove ...'.

Signed-off-by: Carter Wang <carter.wang@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-19 22:08:23 +00:00