This patch enables hostapd.sh to properly configure wpa_supplicant
for when GCMP is used as cipher in station mode.
Without this wpa_supplicant will be unable to connect to AP.
This is needed for wil6210 as it does not support CCMP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The usual OpenWrt-way of writing the JFFS2-marker in order to have
a filesystem erased at the next boot fails on UBIFS volumes due to
UBI being a different beast when it comes to writing.
As truncating a UBIFS volume only takes a few milliseconds and has the
desired effect of wiping-out all content of that volume, just do that
instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
`which` utility is not shipped by default for example on recent Arch
Linux and then any steps relying on its presence fails, like for example
following Python3 prereq build check:
$ python3 --version
Python 3.9.1
$ make
/bin/sh: line 1: which: command not found
/bin/sh: line 1: which: command not found
/bin/sh: line 1: which: command not found
...
Checking 'python3'... failed.
...
Fix this by switching to Bash builtin `command` which should provide
same functionality.
Fixes: FS#3525
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is good practice to define device tree files based on specific
SoCs. Thus, let's not start to create files that are used across
different architectures.
Duplicate the DTSI file for D-Link DAP-2xxx in order to have one
for qca953x and one for qca955x, respectively.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device is a one-port, but was set up as two-port by the
default case in 02_network. Fix it.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* QCA9533, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R
* 10/100 Ethernet Port, 802.11af PoE
* IP55 pole-mountable outdoor case
Installation:
* Factory Web UI is at 192.168.0.50
login with 'admin' and blank password, flash factory.bin
* Recovery Web UI is at 192.168.0.50
connect network cable, hold reset button during power-on and keep it
pressed until uploading has started (only required when checksum is ok,
e.g. for reverting back to oem firmware), flash factory.bin
After flashing factory.bin, additional free space can be reclaimed by
flashing sysupgrade.bin, since the factory image requires some padding
to be accepted for upgrading via OEM Web UI.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Specifications:
* QCA9558, 16 MiB Flash, 256 MiB RAM, 802.11n 3T3R
* QCA9984, 802.11ac Wave 2 3T3R
* Gigabit LAN Port (AR8035), 802.11at PoE
Installation:
* Factory Web UI is at 192.168.0.50
login with 'admin' and blank password, flash factory.bin
* Recovery Web UI is at 192.168.0.50
connect network cable, hold reset button during power-on and keep it
pressed until uploading has started (only required when checksum is ok,
e.g. for reverting back to oem firmware), flash factory.bin
After flashing factory.bin, additional free space can be reclaimed by
flashing sysupgrade.bin, since the factory image requires some padding
to be accepted for upgrading via OEM Web UI.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Specifications:
* QCA9533, 16 MiB Flash, 64 MiB RAM, 802.11n 2T2R
* 10/100 Ethernet Port, 802.11af PoE
Installation:
* Factory Web UI is at 192.168.0.50
login with 'admin' and blank password, flash factory.bin
* Recovery Web UI is at 192.168.0.50
connect network cable, hold reset button during power-on and keep it
pressed until uploading has started (only required when checksum is ok,
e.g. for reverting back to oem firmware), flash factory.bin
After flashing factory.bin, additional free space can be reclaimed by
flashing sysupgrade.bin, since the factory image requires some padding
to be accepted for upgrading via OEM Web UI.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Adds a new function get_magic_fat32() in base-files to read FAT32 magic.
Now FAT32 EFI system partition can be handled in the same way as FAT12/FAT16.
Signed-off-by: Kagurazaka Kotori <kagurazakakotori@gmail.com>
[replace '-o' with '] || [' to satisfy shellsheck]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This package is not needed in base. It will be imported in the packages
feed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Paul Spooren <mail@aparcar.org>
The package `usbutils` already offers an USB reset function, this
package is therefore not really required standalone.
CC: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Paul Spooren <mail@aparcar.org>
This adds an option "hostapd_bss_options" that does the same as
"hostapd_options" but on a per-BSS level, instead of a per-device level.
This can be used, for example, to configure different per-devce sae_passwords
per BSS or to augment some of the existing per-BSS options.
Signed-off-by: Florian Beverborg <flo@beverb.org>
[remove whitespace errors, bump release]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Commit 29ca10e537 ("ipq806x: remove support for kernel 4.19") moved
DTS files to "files" directory, but after that a new DTS file was added
to the former "files-5.4" directory. Move it to the new directory.
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Kernel config does not need to be executable. 644 is enough.
Fixes: 25d9df670b ("mediatek: add v5.4 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[split by targets]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DTS files do not need to be executable. 644 is enough.
Fixes: 0fbdb51f76 ("ipq40xx: add Edgecore OAP-100 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[split by targets]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The phy label/node name should correspond to the reg property.
While at it, use more common decimal notation for reg property itself.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Legacy minstrel is essentially unmaintained and was showing poor performance
Replace it with minstrel_ht and improve rate selection and sampling behavior
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The qemustart script currently picks the ext4 filesystem rather than
squashfs, while the latter is default for nearly all OpenWrt targets.
Change the default behaviour of qemustart to be in line with the rest.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This fixes the following build problem in hostapd:
mipsel-openwrt-linux-musl/bin/ld: /builder/shared-workdir/build/tmp/ccN4Wwer.ltrans7.ltrans.o: in function `crypto_ec_point_add':
<artificial>:(.text.crypto_ec_point_add+0x170): undefined reference to `ecc_projective_add_point'
mipsel-openwrt-linux-musl/bin/ld: <artificial>:(.text.crypto_ec_point_add+0x18c): undefined reference to `ecc_map'
mipsel-openwrt-linux-musl/bin/ld: /builder/shared-workdir/build/tmp/ccN4Wwer.ltrans7.ltrans.o: in function `crypto_ec_point_to_bin':
<artificial>:(.text.crypto_ec_point_to_bin+0x40): undefined reference to `ecc_map'
Fixes: ba40da9045 ("wolfssl: Update to v4.6.0-stable")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 57e4cc8261.
Cmdline override patch was fixed. It's time for reenable
Asrock G10 support.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> (run-tested for R7800)
900-arm-add-cmdline-override.patch have missplaced entry in
arch/arm/Kconfig file. It causes problem with other cmdline
patches. This patch put Kconfig entry in correct place.
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Suggested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> (run-tested for R7800)
With commit 2ca084cc ("build: improve ccache support") these variables
are being set globally and we don't need them for specific targets.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
The symbol determines if the libevent2-pthreads libraries get built or not.
If we want to select libevent2-pthreads, and these haven't been built, an
error will occur mentioning that there are no 'libevent_pthreads-2.1.so'
files.
Adding CONFIG_PACKAGE_libevent2-pthreads to PKG_CONFIG_DEPEND will make
sure that the libraries get re-built in case libevent2-pthreads is
selected.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The `functions.sh` script has `config_get_bool()` function, which is
usable when using UCI config direct access API, but there is no
equivalent for the callback API. Introduce `get_bool()` function to
allow reusing it from init scripts.
Example:
```sh
option_cb() {
local option="$1"
local value="$(get_bool "$2")"
...
}
```
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Since we're now able to select CONFIG_NET_UDP_TUNNEL at will, drop the fake
dependencies.
This is a partial revert of commit d7e040f8bc
"kernel: add fake users for udptunnel and iptunnel modules".
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
UDP tunneling support isn't user-selectable, but it's required by WireGuard
which is, for the time being, an out-of-tree module. We currently work around
this issue by selecting an unrelated module which depends on UDP tunnelling
(VXLAN). This is inconvenient, as it implies this unrelated module needs to be
built-in when doing a monolithic build.
Fix this inconvenience by making UDP tunneling user-selectable in the kernel
configuration.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
While parsing the nm output, we need to account for the fact that 64-bit kernels
have 64-bit wide addresses. While at it, replace the grep | sed combo with a
single awk invocation and a stronger regex.
Fixes: 2ef0acc5fc "kernel-build: fix
STRIP_KERNEL_EXPORTS for recent kernels"
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This patch bumps cryptodev-linux to the latest stable release (1.11) and fixes
compilation against the next LTS (and likely OpenWrt) kernel 5.10.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Fixed license information.
Adjusted Makefile to new install paths.
Backported upstream patch to fix compilation with musl. Replaces local
and incomplete patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This patch was already applied upstream and not needed here.
Fixes: 06403981e1 ("ppp: update to version 2.4.7.git-2019-05-06")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This version fixes a large number of bugs, although no security
vulnerabilities are listed.
Full changelog at:
https://www.wolfssl.com/docs/wolfssl-changelog/
or, as part of the version's README.md:
https://github.com/wolfSSL/wolfssl/blob/v4.6.0-stable/README.md
Due a number of API additions, size increases from 374.7K to 408.8K for
arm_cortex_a9_vfpv3-d16. The ABI does not change from previous version.
Backported patches were removed; remaining patch was refreshed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This patch was backported to the 5.4 kernel tree as commit
c2d5c4df27e0 at least since release v5.4.28. Since then, it enables RX
an TX ready override twice.
Signed-off-by: David Bauer <mail@david-bauer.net>
glibc started to return errors from dlerror() for dlsym() lookup failures which
results in a lot of messages from fakeroot like
dlsym(acl_get_fd): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_get_fd
dlsym(acl_get_file): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_get_file
dlsym(acl_set_fd): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_set_fd
when building OpenWrt using a recent glibc. Use the patch from the upstream
Debian package to silence these messages.
Link: https://bugs.debian.org/830912
Fixes: FS#3393
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Multiple prereq checks are only required within the build system but not
for the ImageBuilder. These checks are excluded by using ifndef IB.
This commit merges the three ifndef IB blocks together.
Signed-off-by: Paul Spooren <mail@aparcar.org>
By setting 'auto', the zero address or the empty string as source
address (option ipaddr, option ip6addr), vxlan will choose one
dynamically. This helps in setups where a wan ip or prefix changes.
This corresponse to setting up an vxlan tunnel with:
proto vxlan6:
# ip link add vx0 type vxlan id ID local :: ...
proto vxlan:
# ip link add vx0 type vxlan id ID local 0.0.0.0 ...
While it is possible to not specify a source ip at all, the kernel will
default to setting up a ipv4 tunnel. The kernel will take any hint from
source and peer ips to figure out, what tunnel type to use. To make sure
we setup an ipv6 tunnel for proto vxlan6, this workaround is needed.
This will not change the behaviour of currently working configurations.
However this will allow former broken configurations, namely those not
specifying both a source address and tunnel interface, to setup a
tunnel interface. Previously those configurations weren't reporting an
error and were stueck in a setup loop like in Bug FS#3426.
This change lifts the currently very strict behaviour and should fix the
following bug:
Fixes: FS#3426
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3426
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
Upstream switched to building with CMake. Adjust accordingly.
Reapplied patch as upstream changed the file format.
Added HOST_BUILD_PARALLEL for faster compilation.
Added cmake tool dependency and removed circular dependencies as a
result.
Adjusted dependent tools to use NOCACHE as they are needed to build
ccache.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Since updating the MDIO driver, the probe will fail hard on any
PHY not present on the bus, while this was not the case prior.
Fixes commit 26b1f72381 ("ipq40xx: net: phy: ar40xx: remove PHY
handling")
Signed-off-by: David Bauer <mail@david-bauer.net>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
WAN/LAN LEDs appear to be wrong in ar71xx and have been swapped here.
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[add LED swap comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* external antenna
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
