TP-Link CPE710-v2 is an outdoor wireless CPE for 5 GHz with one Ethernet
port based on the AP152 reference board. Compared to the CPE710-v1, the
only change observed in hardware is that the mdio address of the ethernet
physical changed from 0x4 to 0x0.
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate), based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO parabolic antenna
- Power, LAN, WLAN5G Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for around
30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5572e0196a93604716ec36ebb8db6737fc6677aa)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is done in preparation of adding support for the CPE710-v2,
which uses a similiar device tree.
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 832cc8ce04122ea726178687b5168187b2465f7f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.
Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"
Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.
Installation:
- Using the bootloader web server. Hold the reset button while turning
the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.
LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
(GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.
Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.
MAC addresses as verified by OEM firmware:
use address source
2g *:b0 factory 0x4 (label)
5g *:b1 factory 0x8004
LAN *:b2 factory 0x28
WAN *:b3 factory 0x2e
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Link: https://github.com/openwrt/openwrt/pull/16927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3a9752ea027b8969750c0dd7f89b6afc357dcffa)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5eb25dddb17fa3cf4958e91dfc9fc868c9eb03ac)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
New stm32 target introduces support for stm32mp1 based devices.
For now it includes an initial support of the STM32MP135F-DK device.
The specifications bellow only list supported features.
Specifications
--------------
SOC: STM32MP135FAF7
RAM: 512 MiB
Storage: SD Card
Ethernet: 2x 100 Mbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
Buttons: 1x Reset, 1x User (USER2)
USB: 4x 2.0 Type-A
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 851e7f77e424f24cda8531330f2d82ebc942c0a4)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These packages are needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e109831e07e398cc50839a30a1cf18c4436983f4)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The snd-usb-audio drivers uses media controller if media controller is set.
So add kmod-media-controller as dependency.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 109592524663ae8bbda47e4ad51a124153a1c903)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit bb3418f21f7b8fe0dcd335375d183dd2a81772bf)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b0adf5e0fdc0d4b449bced9191a95bf08124c1ac)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7bcc68ede36dcc66ec6cdb45c3201e0af0f90708)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6b9df468f05fefa21a8cbce2fdb2e59692b4d246)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e606366a2e018e0a3b25e3dd4b3a937bb53c70e1)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ff96bd84ce0bae633007cf0de82d69796cf3508a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This package contains nvram files for Murata's Wi-Fi/Bluetooth modules.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit be937952fdf8f78fb45ea001258074ddb45e0891)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All stm32 devices use BCM43430 Wi-Fi interface in SDIO mode.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 456e0aad97413816aee41e68b3d3cfdfadc2fd43)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add ATF for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 08dcb73c8d05aa774957422731bfed1b322648d7)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add U-Boot for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ac79ad0757764028a138d0138c8d9aa74420f9ed)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add OP-TEE for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit fae25d4001bcbae0bb1ce60b676bd421e97d78fc)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add a generic template include/optee-os.mk to build OP-TEE.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dedb90e8f82a179ad67b6eac3b6f8862b9183077)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)
These partitions weren't used:
firmware_backup
zrsave
config2
Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d8a9669093359d60f4d6f183b58a22f24cf01731)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit e52c57bb1b30375e0bcc5523db76a672a4a8b4a4 renamed all
network ports to match the faceplate of the Gowin 1U Rack
Mount Server and added the br-lan bridge for the eth* ports.
This commit adds the PoE port to the br-lan bridge and a
br-wan bridge for the two SFP ports so that all ports are
part of the default network configuration.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 75af6a0d736a696ca726cb44d813791858c29f0c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 3467ea905b40f0df87700a15b716b1f5a4efc955.
I merged it by accident.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 52b6c9247997e51a97f13bb9e94749bc34e2d52e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Popular bpi-r3 pwm fans like this one
https://www.amazon.com/youyeetoo-Barebone-Fan-BPI-R3-Integrated/dp/B0CCCTY8PS
will not work properly with current openwrt-23.05/24.10 firmware.
Trying different pwm setting
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
At the moment we have following cooling levels:
cooling-levels = <255 96 0>;
for cpu-active-high, cpu-active-medium and cpu-active-low modes correspondingly.
Thus only cpu-active-high and cpu-active-low are usable. I think this is wrong.
This patch fixes cpu-active-medium settings for bpi-r3 board.
PS: I know, the patch is not ideal as it can break pwm fan for some users.
There are some peoples that use handmade cooling solutions, but:
* discussed cooler is the only 'official' pwm cooler for bpi-r3
available on the market.
* most peoples will use passive cooling available on the market or
the discussed cooler.
* the pwm-fan dts section was added before the official cooler
appears on the market.
Thus it should not be a lot of harm from this fix.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16974
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3467ea905b40f0df87700a15b716b1f5a4efc955)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 22664498ebdd47aad9b15f62edbcaadd851fd62c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bec8edb6d61eb74e8d7578749560cbb5040f307a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e9dd6da91661612d2330c2b633f3dd55b93218f8)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Now that omnia-eeprom is marked nonshared building the cortex-a9 mvebu
subtarget will fail with:
ERROR: unable to select packages:
omnia-eeprom (no such package):
required by: world[omnia-eeprom]
This is because omnia-eeprom depends on TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia
which will not be satisfied in buildbots since CONFIG_TARGET_ALL_PROFILES
and CONFIG_TARGET_PER_DEVICE_ROOTFS are set in which case
CONFIG_TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia is not set.
So, lets simply depend on the mvebu/cortex-a9 subtarget.
Fixes: 371e7bef4046 ("omnia-eeprom: Mark it nonshared")
Link: https://github.com/openwrt/openwrt/pull/17007
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 90de3b277b8e1d121b2f7023578979c6b616167f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CONFIG_FB_INTEL is now visible on x86 since i915 driver is packaged as kmod
now and it stops compilation, so add it to the generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 57daea682e1c6e6da91f92efed717159f9ffffb0)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The config_get_bool also works with on/off, yes/no, true/false.
Add 'main' section name. This will make it easier to change settings from uci.
Add a link to documentation.
Signed-off-by: Sergey Ponomarev <stokito@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15579
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 4511fa4b30f73185597990ce563bbf3f96385292)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These get dynamically set based on compiler version. Not relevant for
targets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cd92cbddf8c473507a9af290c99f2aef8c368784)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Move settings CONFIG_INTEL_MEI_GSC_PROXY, CONFIG_INTEL_MEI_HDCP
and CONFIG_INTEL_MEI_PXP to target generic.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16971
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 84665993d6beed8ac2b557f8d3e005a29e3fd09c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This tool was build in the phase 2 build, there the
TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia dependecy was probably
not meat. Mark it as non shared to build it together with the target
where this option is set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16975
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 371e7bef4046fb3992ecfb92b5b741c22fa3ade6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Disable drm-i915 module for target x86/geode.
Fixes: 77cfe8f ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16977
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 226f74badd61fb1586dd3531835aeaa3bf6fe467)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 491121288eaa9d20f3db8215a4790e8f0ee1f8ca)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fe481c9c47d97ebde1bc3c959924f4f9227c6c16)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5583d2318966d5d5dcdbdec2e34b8815d3f6419a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
On aarch64 musl gcc 14.x compiler, trying compiling elfutils 0.192 with
lto option enabled will cause null-dereference error.
Example error message:
...
elf_compress.c: In function 'elf_compress':
elf_compress.c:675:26: error: potential null pointer dereference [-Werror=null-dereference]
675 | shdr->sh_flags |= SHF_COMPRESSED;
| ^
elf_compress_gnu.c: In function 'elf_compress_gnu':
elf_compress_gnu.c:127:25: error: potential null pointer dereference [-Werror=null-dereference]
127 | shdr->sh_size = new_size;
| ^ ^
...
This is a false postive warning but will abort compilation if gcc has
`-Werror` flag. This commit add a patch for this, see the bugzilla
report below.
This commit backports a series of patches to fix some errors.
Add patch:
- 007-add-libeu-symbols-to-libelf.patch
- 008-fix-autoconf-ENABLE_IMA_VERIFICATION.patch
- 009-fix-null-dereference-with-lto.patch
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=32311
Signed-off-by: Ryan Keane <the.ra2.ifv@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16886
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit afffcd09e5f15be53f327a80ee87d391312eb805)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since the start of the Realtek target OpenWrt works with RTL83XX as the
target architecture. Upstream is using MACH_REALTEK_RTL instead. To
simplify further development align that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 65964c42f8744ed8ca09448a155b99e3a99be283)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently, libreadline only installs
```
/usr/lib/libhistory.so.8 -> libhistory.so.8.2
/usr/lib/libhistory.so.8.2
/usr/lib/libreadline.so.8 -> libreadline.so.8.2
/usr/lib/libreadline.so.8.2
```
But there is no `libreadline.so` or `libhistory.so` available.
So this happens:
```
root@OpenWRT:~# cat a.c
int main() {
}
root@OpenWRT:~# gcc a.c -lreadline
/usr/bin/ld: cannot find -lreadline: No such file or directory
collect2: error: ld returned 1 exit status
```
Unless, of course, one uses `-l:libreadline.so.8`... But that
doesn't help with binaries that try to dynamically open
`libreadline.so`. I have one of those here (the STklos Scheme
compiler -- I didn't make a PR for it because it's far from
being ready, but one issue is that it does use dlopen to use
readline...)
With the symlink, it works:
```
root@OpenWRT:~# ln -s /usr/lib/libreadline.so.8 /usr/lib/libreadline.so
root@OpenWRT:~#
root@OpenWRT:~# gcc a.c -lreadline
root@OpenWRT:~#
```
Another example: when trying to package rlwrap, the build failed
complaining it could not find readline (using `-lreadline`).
It would then be necessary to change rlwrap's `configure.ac`
(and also in all packages that use readline), but it seems
simpler to add the symlinks...
This PR changes the Makefile so it will include the links.
Signed-off-by: Jeronimo Pellegrini <j_p@aleph0.info>
Link: https://github.com/openwrt/openwrt/pull/16445
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 0000ba6ab8062f965d8fed240b76d36f9a493b55)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit fixes and closes#16313.
Switch the x86 kernel's timer to tickless operation which is
more power efficient since it is not woken up by periodic timer
interrupts when idle. Also add several other options for CPU
idle governors particularly the upstream default for tickless
kernels, CONFIG_CPU_IDLE_GOV_MENU. Without this commit, my AMD
Ryzen 7 5800U can only achieve a minimum core frequency of 1,384
MHz which is over 3x higher than the processor's minimum
frequency of 400 MHz which is accessible with this modification.
In addition to the lower clock rate, I have seen a concomitant
reduction in both idle temps and at-the-wall power consumption.
Summary:
* Idle CPU freqs dropped from 1,384 MHz to 400 Mhz.
* Idle power consumption dropped from 7 W avg to 5 W.
* Idle temps have dropped from 50C on avg to 43C.
There are other well known reasons to switch to a tickless
timer including: reduced interrupt overhead, better use of CPU
resources, and reduced latency to name a few.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16317
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 31111680f6fc5f17201b02b8ce656b955be56d7a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
