Biggest fix for this version is CVE-2021-3336, which has already been
applied here. There are a couple of low severity security bug fixes as
well.
Three patches are no longer needed, and were removed; the one remaining
was refreshed.
This tool shows no ABI changes:
https://abi-laboratory.pro/index.php?view=objects_report&l=wolfssl&v1=4.6.0&v2=4.7.0
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit d1dfb577f1)
The Netgear R6800 and R6700v2 devices have a Semtech SX1503 GPIO
expander controlling the device LEDs. This expander was initially
supported on 4.14, but support was lost in the transition to 5.4.
Since this driver cannot be built as a kernel module, enable it in the
kernel config for all mt7621 devices.
Run-tested on a Netgear R6800.
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 773949c152)
As suggested by Sergio, this adds GPIOs 19 and 8 explicitly into the
DIR-860L DTS, so the PCI-E ports get reset and the N radio (radio1)
on PCI-E port 1 comes up reliably.
Fixes the following error that popped up in dmesg:
[ 1.638942] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
Suggested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
(cherry picked from commit 06356f0020)
* use binary provided by MediaTek to work-around 'bromimage' issue
* use @OPENWRT mirror for blobs
* refactor Makefile
* add mt7622 1c variants (using binaries provided by MTK)
(cherry picked from commit 068c82039f and
commit 9cd089dbbf)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The current driver has some troubles:
- Some groupings are wrong.
- The pinctrl group0 owns pins never used (at least in Openwrt) for any
pinmux. The driver hijacks all the pins on the group avoiding any other
use, spite they're free. I.e. for buttons, causing this kernel error:
[ 4.735928] gpio-keys-polled keys: unable to claim gpio 479, err=-22
[ 4.742642] gpio-keys-polled: probe of keys failed with error -22
- Minor errors about groupings on the documentation
- Missing "diag" grouping in dtsi
- Wrong groupings in dtsi
Fix it by setting the correct groups.
And relax the pin capturing, letting the gpios belonging to any group to
be used for other purposes like buttons. This was the behavior with stock
firmwares and old OpenWrt versions which never caused any trouble.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(Cherry-picked from commit 50cb3a750f)
Since there are only 16 characters available, on most cases the vendor name
will fit in the metadata, but the model name won't fit.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit c27532742d)
The lan port sequence was reversed compared to the labels.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 567a88e4b9)
Phicomm K2G:
add missing label_mac
Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 55263ffedb)
pinctrl should rely on external interrupt controller for GPIO interrupts.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 36e35b8d81)
When building from a local branch based off the "openwrt-21.02" branch,
version computation is wrong, because the number of local commits is
computed against master. As a result, it wrongly counts *all* commits
since the beginning of the openwrt-21.02 branch as local commits.
The fix is to compare to the openwrt-21.02 branch instead, which gives the
expected result.
A similar change had been applied to the openwrt-19.07 branch:
891022918d ("scripts: getver.sh: fix version based on stable branch")
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
The ls-ddr-phy package needs fiptool options that are not
available via the version from arm-trusted-firmware-tools.
This breaks build for layerscape with the recently added LX2160a:
create: unrecognized option '--ddr-immem-udimm-1d'
Use the tfa-layerscape variant again for now, but rename it to
fiptool-layerscape to indicate that it's a specific variant.
This reverts 84bc7d31e0 ("tfa-layerscape: don't build fiptool").
Fixes: f59d7aab2a ("layerscape: add ddr-phy package")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 910b5d669f)
Now that khwrngd is working on all subtargets we can remove urgnd.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 9dc84018ee)
Also add a patch setting its quality, which should make it usable by khwrngd.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 670526efa3)
This patch allows devices without a high resolution timer to boot up faster.
It should speed up boots for bcm2708 and bcm63xx.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 7747b3fa36)
This is a backport of the upstream commit 58bbbb598144 ("nl80211: Ignore
4addr mode enabling error if it was already enabled") which fixes same
issue as in the current fix contained in '130-wpa_supplicant-multi_ap_roam.patch',
but in a different way:
nl80211_set_4addr_mode() could fail when trying to enable 4addr mode on
an interface that is in a bridge and has 4addr mode already enabled.
This operation would not have been necessary in the first place and this
failure results in disconnecting, e.g., when roaming from one backhaul
BSS to another BSS with Multi AP.
Avoid this issue by ignoring the nl80211 command failure in the case
where 4addr mode is being enabled while it has already been enabled.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
[bump PKG_RELEASE, more verbose commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit fb860b4e41)
The Netgear EX6150 can, just like the D-Link DIR-860L rev B1, fail to
initialise both radios in some cases. Add the reset GPIOs explicitly
so the PCI-E devices get re-initialised properly. See also FS #3632.
Error shows up in dmesg as follows:
[ 1.560764] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[removed period from commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit af1b6799c6)
Support new devices LS1046AFRWY and LX2160ARDB in README.
Clean up README, and add missing LS1021ATWR deploy guide.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[adjust set of devices added, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a31842e7fd)
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.
- Enables network intelligence with the next generation Datapath (DPPA2)
which provides differentiated offload and a rich set of IO, including
10GE, 25GE, 40GE, and PCIe Gen4
- Delivers unprecedented efficiency and new virtualized networks
- Supports designs in 5G packet processing, network function
virtualization, storage controller, white box switching, network
interface cards, and mobile edge computing
- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
and 8-core LX2080A)
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 80dcd14abe)
Add ddr-phy package for layerscape. Currently only LX2160ARDB
requires the package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f59d7aab2a)
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.
The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2c2d77bd3b)
Upcoming devices will not need the migration setup, so let's move
it out of the common definition.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a9075d42d7)
As kernel size increased it start to fail to load squishfs image,
using lzma-loader fixed it.
wevo_11acnas is almost same device as w2914ns-v2 except ram size,
so I expect same thing would've happen in that device too.
Signed-off-by: Seo Suchan <abnoeh@mail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit ca6954e2dc)
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.
When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.
The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.
Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
* Back side: ETH0, PoE PD port
* Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)
Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).
Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
eth a4:2b:b0:...:88
ra0 a4:2b:b0:...:88
rai0 a4:2b:b0:...:89
Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface
Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
# tftpboot 84000000 openwrt-initramfs.bin
# bootm
Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
$ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
-z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin
This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.
Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
This was an issue with the ddc75ff704 version of mt76, but appears to
have improved/disappeared with bc3963764d.
Error notice example:
[ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout
Hardware was kindly provided for porting by Stijn Segers.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 1e75909a35)
Similarly to the Archer C2 v1, the Archer C20 v1 will brick when one
tries to flash an OpenWrt factory image through the TP-Link web UI.
The wiki page contains an explicit warning about this [1].
Disable the factory image altogether since it serves no purpose.
[1] https://openwrt.org/toh/tp-link/tp-link_archer_c20_v1#installation
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 0265cba40a)
We can now use the power LED for diag in more devices thanks to the latest
patches from the RPi foundation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 5bab472a11)
Support added to bcm2709 (32 bits) and bcm2711 (64 bits).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit 8ad61118fd)
Ran update_kernel.sh in a fresh clone without any existing toolchains.
No manual changes needed.
Build system: x86_64
Build-tested: bcm27xx/bcm2711
Signed-off-by: John Audia <graysky@archlinux.us>
(cherry-picked from commit 5d3a6fd970)
GetABISuffix does not work for intra-package ABI version of provided symbols,
since ABIV_$(provided) is not set.
Fix ABI version by using $(ABIV_$(1)) directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 0db9d11865)
Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 634c13c186)
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c9137e2ddf)
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
(cherry picked from commit 6e4e97b2256327bb380ee2a83da9a1ddf657e395)
This fixes 4 security vulnerabilities/bugs:
- CVE-2021-2839 - SSLv2 vulnerability. Openssl 1.1.1 does not support
SSLv2, but the affected functions still exist. Considered just a bug.
- CVE-2021-2840 - calls EVP_CipherUpdate, EVP_EncryptUpdate and
EVP_DecryptUpdate may overflow the output length argument in some
cases where the input length is close to the maximum permissable
length for an integer on the platform. In such cases the return value
from the function call will be 1 (indicating success), but the output
length value will be negative.
- CVE-2021-2841 - The X509_issuer_and_serial_hash() function attempts to
create a unique hash value based on the issuer and serial number data
contained within an X509 certificate. However it was failing to
correctly handle any errors that may occur while parsing the issuer
field (which might occur if the issuer field is maliciously
constructed). This may subsequently result in a NULL pointer deref and
a crash leading to a potential denial of service attack.
- Fixed SRP_Calc_client_key so that it runs in constant time. This could
be exploited in a side channel attack to recover the password.
The 3 CVEs above are currently awaiting analysis.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 482c9ff289)
File extension was truncated for
pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 487b7ae5eb)
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 75455b75a7ee)
Let's switch to 5.10 now that mac80211 has been updated.
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit a5c4c40476)
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
