This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Make all the patches apply and delete the ones already integrated into
upstream Linux kernel. This also refreshes some of the kernel
configurations.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[refreshed for linux 6.1.89]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This refreshes the configuration for Linux kernel 5.15.
I first selected the xrx200 subtarget and then refreshed the target
kernel configuration using this command:
make kernel_oldconfig CONFIG_TARGET=target
Then I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
I compared the kernel configuration used to compile the kernel from the
build directory for each subtarget before and after this task and it was
still the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[refreshed config for linux 5.15.158]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
The Arcadyan VRV9510KWAC23 (trade name Livebox Next) is a Lantiq router distributed by some spanish ISPs
Hardware:
- SoC: Lantiq VRX200
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 256 MiB DDR2
- Flash: 128 MiB NAND
- Ethernet: Built-in Gigabit Ethernet switch, 5x 1GbE
- Wifi 2.4GHz: Broadcom BCM43222KFBG 802.11b/g/b MIMO 2T2R
- Wifi 5GHz: Broadcom BCM4360KMLG 802.11ac MIMO 3T3R
- USB: 2x USB 2.0
- DSL: Built-in VDSL/ADSL2+ XWAY VRX208
- LEDs: 8x
- Buttons: 4x
- Phone: Lantiq PEF 42068 V XWAY SLIC120
Install instructions:
Detailed instructions can be found on the wiki https://openwrt.org/toh/arcadyan/vrv9510kwac23
1. Boot into UART mode and upload the the https://raw.githubusercontent.com/danielhuici/arcadyan-vrv9510kwac23-utils/main/u-boot.asc file via serial console to boot into U-Boot.
2. Perform a backup of the NAND
3. Setup a TFTP server and serve the https://github.com/danielhuici/arcadyan-vrv9510kwac23-utils/raw/main/u-boot.ltq.lzo.nandspl. Replace the OEM bootloader with this one. Erase your NAND and write the image into it
4. Reboot the router
5. Serve the OpenWrt ramdisk image on your TFTP server and boot it via U-Boot
6. When OpenWrt boots, flash the SquashFS OpenWrt image using LuCi interface, so OpenWrt gets installed into the NAND
Signed-off-by: Daniel Huici <danielhuici@hotmail.com>
This adds support for the Fritzbox 3490 device. It contains two
SoCs, one Lantiq with a 5GHz WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module which is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
- Without telephony or ISDN
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This adds support for the Fritzbox 5490/5491 devices. They contain
two SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module which is not supported with this commit.
Both devices have fiber WAN ports.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port Lantiq gswip switch,
4x 1000/100/10 port (additional qca8334 switch for 2 ports), Port 5 is
fixed and connected to the Wireless SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- AT 8033 based AON fiber port (5490) or GPON fiber port (5491)
Unsupported:
- DECT and ISDN telephony
- Two ethernet ports (on extra switch) and fiber port not working
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This adds support for the Fritzbox 7490 device. It contains two
SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module and is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
Unsupported:
- DECT and ISDN telephony
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
This reverts commit 0c117e1f6c.
Activate the lantiq/xrx200 target again.
There are still some problems with the GSWIP, but it is not leaking
packets to the wrong bridge in normal operations.
It shows some error messages at configuration like these:
[ 54.308861] gswip 1e108000.switch: port 5 failed to add ce:9d:84:d1:81:f0 vid 1 to fdb: -22
[ 54.325633] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 0 to fdb: -22
[ 54.351242] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 1 to fdb: -22
[ 54.358311] gswip 1e108000.switch: port 5 failed to delete ce:9d:84:d1:81:f0 vid 1 from fdb: -2
The problems are described in this pull request:
https://github.com/openwrt/openwrt/pull/13200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The current problems blocking the switch to the kernel 5.15 are
related to the GSWIP driver. This driver is only used by the
xrx200 subtarget. The other subtargets are unaffected by this
problem.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
this was thoroughly tested (warm and cold boots). on a
real 7360v2. This is because there have been documented
hick-ups with other lantiq devices that need the
owl-loader too.
It's likely that the 7360(sl) could be converted in the
same way as well. However the 7362sl uses a reversed
caldata format, so the "qca,no-eeprom" stays in place.
The patch also moves the urloader nvmem partition
definition into the partition section.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The WIFI LED already worked for me with the latest openwrt 22.03 version.
Wifi LED did not with an older 22.x version (in gluon - there phy0radio did nothing but phy0tpt did show activity
the WAN interface has the name "wan" and not "pppoe-wan" on this device
fixes#7757 (and FS#2987)
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
After enhancing ltq-deu, build it by default for the devices
using it.
Reverts: 964863b ("ltq-deu: Mark lantiq DEU broken")
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
It was reported the caldata on the FritzBox 7430 is not only stored at
different offsets, but is also larger than the current output size
limit.
Increase the output file size limit (after deflate) by 1024 bytes.
Ref: FS#3604 ("ath9k firmware is 0 bytes on Fritzbox 7430")
Signed-off-by: David Bauer <mail@david-bauer.net>
It was reported the AVM FritzBox 7430 has different offsets for the
caldata depending on the device.
Whether this is due to custom bad-block handling or up to the installed
bootloader-version is unknown.
Try both known caldata offsets like it is already done for the ipq40xx
NAND based models. Use the same approach for the FritzBox 7412. While it
is currently unknown, whether it is affected, applying the same logic
has no downsides.
Signed-off-by: David Bauer <mail@david-bauer.net>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
adds the correct offset for the calibration data.
The values are according to the OpenWrt Forum Thread:
"Fritzbox 7430 and wifi".
Link: <https://forum.openwrt.org/t/fritzbox-7430-and-wifi/86944>
Reported-by: RENErica
Signed-off-by: Joel Linn <jl@conductive.de>
[changed commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The current state of the kernel 5.4 support is in the openwrt-21.02
branch. No need to keep a not default used kernel in this branch.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
When the ltq_deu_vr9 kernel module is loaded, hostapd does not start any
more. It fails with this error message:
daemon.err hostapd: nl80211: kernel reports: key addition failed
daemon.err hostapd: Interface initialization failed
OpenWrt uses the standard Linux crypto API in the wifi drivers now
and this probably makes the system offload more crypto operations to
special hardware like the Lantiq DEU. There is probably a bug in the DEU
and these operations fail and then hostapd does not start the interface.
Do not include the Lantiq DEU by default any more.
Fixes: FS#3901
Fixes: 53b6783907 ("mac80211: remove patches stripping down crypto support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Notupus <notpp46@gmail.com>
Enable the XRX200 PMAC, GSWIP DSA tag and GSIP DSA drivers in the 5.4
kernel config. Update the existing vr9_*.dts{,i} to use the new
Ethernet and switch drivers. Drop the swconfig package from the xrx200
target because swconfig doesn't manage DSA based switches.
The new /etc/config/network format for the DSA driver is not compatible
with the old (swconfig) based one. Show a message during sysupgrade
notifying users about this change and asking them to start with a fresh
config (or forcefully update and then migrate the config manually).
Failsafe mode can now automatically bring up the first lan interface
based on board.json including DSA based setups. Drop
05_set_preinit_iface_lantiq from the xRX200 sub-target as this is not
needed anymore. For now we are keeping it for the ase, xway and
xway_legacy until there's some confirmation that it can be dropped from
there as well.
While here, some boards also receive minor fixups:
- Use LAN1 as LAN1 (according to a photo this port can also be
configured as WAN) on the Buffalo WBMR-300HPD. This makes it easier to
read the port mapping because otherwise we would have LAN{2,3,4} and
WAN (which was the case for the non-DSA version previously).
- vr9_avm_fritz3390.dts: move the "gpio" comment from port 0 and 1 to
their corresponding PHYs
- vr9_tplink_vr200.dtsi: move the "gpio" comment from port 0 to PHY 0
- vr9_tplink_tdw89x0.dtsi: move the "gpio" comment from port 0 to PHY 0
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Tested-by: Notupus <notpp46@googlemail.com> # TD-W9980/DM200/FRITZ 7430
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TDT VR2020
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TP-Link TD-W8980B
Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on ZyXEL P-2812HNU-F1
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 7490
Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 3490
Tested-by: @jospezial <jospezial@gmx.de> # tested on VGV7510KW22 (o2 Box 6431)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.
[*] As a funny side-fact, copy-pasting has led to almost all
hotplug.d files using the "+", while nearly all of the
02_network files are not using it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Following changes are made to the Lantiq kernel patches:
0001-MIPS-lantiq-add-pcie-driver.patch
The pci header isn't included by the of_pci header any longer
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
Due to the merge of grx390 and ar10 clocks, extend support to grx390
0025-NET-MIPS-lantiq-adds-xrx200-legacy.patch
The do_carrier arguments was dropped from phy_link_change. The
phylib has always sets the third parameter to true so the flag is
always changed anyway.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
The stuck queue is now passed to xrx200_tx_timeout (the timeout
handler) but not used so far.
0028-NET-lantiq-various-etop-fixes.patch
ioremap has provided non-cached semantics by default since the Linux
2.6 days and was removed with kernel version 5.6.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
0042-arch-mips-increase-io_space_limit.patch
Move IO space extension to laniq specific file
Signed-off-by: Mathias Kresin <dev@kresin.me>
The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a
5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq
has access to the flash memory, the Atheros runs fully from RAM.
Specifications
--------------
- Lantiq 500 MHz
- 128MiB RAM
- 128MiB NAND
- 256k Flash
- AR9580 5GHz WiFi
- AR9342 560 MHz
- 64MiB RAM
- AR9328 2.4GHz WiFi
Remarks
-------
This commit only adds support for the Lantiq side of things and
prepares the drivers for communication with the Atheros SoC. Thus,
only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via
another target.
Some kernel patches will be required to add support for the Atheros SoC.
Installation
------------
Use the eva_ramboot.py script to boot the initramfs image. Then, transfer
the sysupgrade image to the device and run sysupgrade to flash it to the
NAND.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl
Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Assign the usbdev trigger via devicetree and drop the userspace
handling of the usb leds.
Drop the now unused userspace helper code as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.
This increases uncompressed kernel size by about 100 bytes on ath79/generic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This patch fixes build of squashfs image on lantiq. Currently the FEATURE
variable is overwritten by the subtarget.
Fixes: FS#3480
Fixes: f1c6523376 ("lantiq: clean up target/subtarget features")
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[reformat Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The feature "squashfs" is defined for target and all subtargets
individually. Remove the redundant entries in the subtargets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware:
- SoC: Lantiq VRX 220
- CPU: 2x MIPS 34Kc 500 MHz
- RAM: 128 MiB 250 MHz
- Flash: 128 MiB NAND
- Ethernet: Built-in Fast Ethernet switch, 4 ports used
- Wifi: Atheros AR9381-AL1A b/g/n with 2 pcb/internal and 1 external antennas
- USB: 1x USB 2.0
- DSL: Built-in A/VDSL2 modem
- DECT: Dialog SC14441
- LEDs: 1 two-color, 4 one-color
- Buttons: 1x DECT, 1x WIFI
- Telephone connectors: 1 FXS port via TAE or RJ11 connector
With the exception of FXS/DECT everything works
(there are no drivers for AVM's FXS or DECT implementation),
DSL is yet untested.
Installation:
Boot up the device and wait a few seconds. Run the eva_ramboot.py script
in scripts/flashing/ to load the initramfs image on the device:
$ ./scripts/flashing/eva_ramboot.py 192.168.178.1 <path to your initramfs image>
If the script fails to reach the device, maybe try 169.254.120.1.
Wait until booting is complete. You should now be able to reach your device
under the default ip address 192.168.1.1.
Before flashing, check if linux_fs_start is not set to 1 in the tffs partition:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If linux_fs_start is 1, you will need to reset it to 0, either by FTP,
upgrading FritzOS or doing a recovery.
Now you should be able to flash the device using sysupgrade.
Signed-off-by: Leon Maurice Adam <leon.adam@aol.de>
Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[drop BOARD_NAME, use wpad-basic-wolfssl, drop 4.19, drop dts-v1,
remove model prefix from LED names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The target uses 5.4 as default kernel since 06/2020.
Kernel 4.19 support is not really maintained anymore, it does not
seem to be needed and upcoming changes (mainly DSA) will break
backward-compatibility anyway.
Thus, make maintaining of old stuff and reviewing of new stuff
easier by removing support for kernel 4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patches for other targets, this will remove
the "devicename" from LED labels in lantiq.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated. The DTS/DTSI consolidation is
only performed for files-5.4.
For lantiq,easy98020 some LED definitions have the form
"devicename:function" without the color, so we need to implement
explicit migration for that one.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is the most popular choice in the linux kernel tree.
Within OpenWrt, this change will establish consistency with ath79
and ramips targets.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[extend commit message, include netgear_dm200, update base-files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Split the /etc/uci-defaults/01_led_migration scripts into subtargets
as already done for most of the other base-files.
While this introduces a minor amount of code duplication, it still
is considered an improvement, as device-specific settings are kept
together in the subtargets' base-files and the script at hand can be
removed entirely for two of the subtargets not needing it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.
Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.
Save 20.3 kB flash memory.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the Fritzbox 7360v2
CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A
DECT is not working.
Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.
Firmware can be flashed with this method:
1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:
passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin
5.) wait till red light flashing turns off.
6.) type: exit
Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.
Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.
The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.
Following changes are made to the Lantiq kernel patches:
0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
applied upstream
0008-MIPS-lantiq-backport-old-timer-code.patch
access_ok API update because it lost it's type (which was the first)
parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
from access_ok() function")
0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
revert upstream changes required for upstream xrx200 ethernet and
xrx200 (DSA) switch driver but breaking our driver
0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
required for our driver but dropped upstream, add former upstream
version
0028-NET-lantiq-various-etop-fixes.patch
now has to use the phy_set_max_speed API instead of modifying
phydev->supported. Also call ltq_dma_enable_irq() in
ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
lantiq: Do not enable IRQs in dma open")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Duplicate kernel 4.19 config and patches for kernel 5.4.
Duplicate the devicetree source files as well, they need kernel 5.4
specific adjustments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reorganizes 02_network board.d files based on what's done for
ath79 and ramips: Instead of putting all settings into a single big
case, the interface/dsl/MAC address setup is put into separate
functions with a specific switch case for each of them. This makes
grouping of devices much easier and should be easier to read, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
