The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit
Ethernet switch, a gigabit Ethernet WAN port and a USB port.
Specification:
- Bootloader: U-Boot
- SoC: MediaTek MT7620A (600 MHz)
- Flash: 16MB, Macronix MX25L12845E
- RAM: 64MB, Nanya NT5TU32M16DG-AC
- Serial: 115200 baud, no header, 3.3V
J2: Vcc (arrow), Gnd, Tx, Rx
- USB: USB 2, 5V
- Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327
- WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N
300 Mb/s, 2T2R
- WiFi1: 2.4 GHz 802.11 b/g/n integrated
300 Mb/s, 2T2R
- Antennas: 2 per radio, internal
- LEDs: 1 programmable power (amber)
2 programable radio (blue)
1 programable WPS-5G (blue)
1 non-programable WAN activity (blue)
1 unconfigured WPS-2.4G (amber)
- Buttons: GPIO: Reset, WPS
Installation:
Use the OEM web interface to install the ...-factory.dlf image.
Use the OpenWRT ...-sysupgrade.bin image for future upgrades.
The J2 serial port can be accessed either by soldering in a header,
standard 0.1" spacing, or by using pogo-pins against the back side.
As configured by the OEM, the U-Boot boot delay is short, however quickly
typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP"
prompt. The TFTP client is configured by default with
client: 192.168.99.9
server: 192.168.99.8
filename: uImageESR600
It will load an OpenWRT initramfs kernel with this method.
Known issues:
1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational.
LAN1 and LAN2 do not appear to power up. This issue is also present
in the Lava LR25G001.
2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED,
is not configured in the Device Tree specification.
3) The blue WAN activity LED is not configured in the Device Tree
specification as this causes the AR8327 switch to fail to initialize.
Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com>
[merge conflict in 02_network]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: Mediatek MT7621A
CPU: 4x 880Mhz
Cache: 32 KB I-Cache and 32 KB D-Cach
256 KB L2 Cache (shared by Dual-Core)
RAM: DDR3 512MB 16bits BUS
FLASH: 16MB
Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN)
POE: (1x PD, 2x PSE)
USB: 1x 3.0
PCI: 3x Mini PCIe (3 USB2.0 + 2 x UIM interface)
GPS: Quectel L70B
SIM: 2 Slots
BTN: Reset
LED: - Power
- Ethernet
- Wifi
- USB
UART: UART is present as Pads with throughholes on the PCB.
They are located on left side.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
The stock image is a modified openwrt and can be overflashed via sysupgrade -F
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
[merge conflict in mt7621.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Winbond W632GG6KB-1)
FLASH: 128MB (Macronix MX30LF1G18AC-TI)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x USB 3.1 (Gen 1)
BTN: Reset, WPS
LED: - Power (blue)
- 5Ghz (blue)
- 2.4GHz (blue)
- Internet (blue)
- 4x LAN (blue)
(LAN/WAN leds are not controllable by GPIOs)
UART: UART is present as Pads marked J4 on the PCB.
3.3V - TX - RX - GND / 57600-8N1
3.3V is the square pad
MAC: The MAC address on the router-label matches the MAC of
the 2.4 GHz WiFi.
LAN and WAN MAC are identical: MAC_LABEL+4
5 GHz WiFi MAC: also MAC_LABEL+4
Installation
------------
Via U-Boot tftpd:
Switch on device, within 2s press reset button and keep pressed
until power LED starts blinking slowly.
Upload factory image via tftp put, the router's ip is 192.168.1.1
and expects the client on 192.168.1.75.
The images also work on the Asus RT-AC65P models as tested by Gabor.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Gabor Varga <vargagab@gmail.com>
[fixed Asus -> ASUS in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Nanya NT5CC128M)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: No
BTN: Reset, WPS
LED: 4 red LEDs, indistinguishable when casing closed
UART: UART is present as Pads marked J1 on the PCB.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the OEM web-interface
(by default:http://192.168.1.1)
The sysupgrade image can be installed via TFTP from
the U-Boot bootloader. Connect ethernet port 2.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[flash node rename, EDIMAX -> Edimax, complete device model name]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
If no device tree is given there is no node generated, but
the configuration does still include the name of the missing node.
This will result in a successful build fit image, but bootm does
throw a error message if we want to boot the bad configuration.
Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
add module to support Emulex OneConnect
common in 10Gbit SFP+ cards by Dell/HP/IBM
supports OneConnect OCe10xxx OCe11xxx OCe14xxx,
LightPulse LPe12xxx
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
wps_supplicant.h assumes that 'struct wpa_bss' is forward declared if
CONFIG_WPS is not defined. With the later inclusion of
600-ubus_support, the issue manifests in warnings like these:
wps_supplicant.h:113:15: warning: 'struct wpa_bss' declared inside parameter list will not be visible outside of this definition or declaration
struct wpa_bss *bss)
^~~~~~~
This patch forward declares 'struct wpa_bss' regardless.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit message facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The original wpa_hexdump uses a 'void *' for the payload. With patch
410-limit_debug_messages, the signature changes and compiler warnings
occur at various places. One such warning is:
wpa_debug.h:106:20: note: expected 'const u8 * {aka const unsigned char *}' but argument is of type 'struct wpa_eapol_key *'
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit message facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The ar71xx images for the Ubiquiti NanoStation M (XW) devices use
"nanostation-m-xw" as the board name, but the ath79 images are only
compatible with the "nano-m-xw" board name, so sysupgrade complains.
By adding this additional supported device, sysuspgrade smoothly
upgrades from ar71xx to ath79.
Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb.
Ref: https://github.com/openwrt/openwrt/pull/2418
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
So far, XW devices have DEVICE_VARIANT defined and XM devices have
no DEVICE_VARIANT set.
This adds DEVICE_VARIANT for XM devices, and moves definitions for
both XM and XW to the common definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds the label MAC address for several devices in
ramips.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- cudy,wr1000
- dlink,dir-615-d
- dlink,dir-615-h1
- dlink,dir-860l-b1
- glinet,gl-mt300a
- glinet,gl-mt300n
- glinet,gl-mt750
- vocore,vocore2
- vocore,vocore2-lite
- zbtlink,zbt-we1326
- zbtlink,zbt-wg3526
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- dlink,dir-510l
- dlink,dwr-116-a1
- dlink,dwr-118-a1
- dlink,dwr-118-a2
- dlink,dwr-921-c1
- dlink,dwr-922-e2
- all hiwifi devices
- lava,lr-25g001
- xiaomi,mir3p
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds the label MAC address for several devices in
ath79.
Some devices require setting the MAC address in 02_network:
For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices
For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For many devices, MAC addresses cannot be retrieved via the
device tree alias.
To still provide the label MAC address for those, this implements
a second mechanism that will put the address into uci config.
Note that this stores the actual MAC address, whereas in DTS
we reference the bearing device.
This is based on the work of Rosy Song <rosysong@rosinson.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
To refer to the MAC address on a device's label, one can
specify the alias label-mac-device in the DTS which should
point to the bearer of the corresponding MAC address.
With the function get_mac_label, the user can retrieve then
retrieve this address and use it as a value that uniquely
identifies his device.
This is severely helpful for several downstream functionalities,
e.g. define MAC addresses of custom netifs or change the SSID to
be easily recognizable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Refresh patches, for changes in version 7.66.0 see https://curl.haxx.se/changes.html#7_66_0
Fixes CVEs:
CVE-2019-5481
CVE-2019-5482
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This version fixes 3 low-severity vulnerabilities:
- CVE-2019-1547: ECDSA remote timing attack
- CVE-2019-1549: Fork Protection
- CVE-2019-1563: Padding Oracle in PKCS7_dataDecode and
CMS_decrypt_set1_pkey
Patches were refreshed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
If an spi-gpio was specified with num-chipselects = <0> in dts, kernel
will crash:
Unable to handle kernel paging request at virtual address 32697073
pgd = (ptrval)
[32697073] *pgd=00000000
Internal error: Oops: 5 [# 1] SMP ARM
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.19.72 #0
Hardware name: Generic DT based system
PC is at validate_desc+0x28/0x80
LR is at gpiod_direction_output+0x14/0x128
...
[<c0544db4>] (validate_desc) from [<c0545228>] (gpiod_direction_output+0x14/0x128)
[<c0545228>] (gpiod_direction_output) from [<c05fa714>] (spi_gpio_setup+0x58/0x64)
[<c05fa714>] (spi_gpio_setup) from [<c05f7258>] (spi_setup+0x12c/0x148)
[<c05f7258>] (spi_setup) from [<c05f7330>] (spi_add_device+0xbc/0x12c)
[<c05f7330>] (spi_add_device) from [<c05f7f74>] (spi_register_controller+0x838/0x924)
[<c05f7f74>] (spi_register_controller) from [<c05fa494>] (spi_bitbang_start+0x108/0x120)
[<c05fa494>] (spi_bitbang_start) from [<c05faa34>] (spi_gpio_probe+0x314/0x338)
[<c05faa34>] (spi_gpio_probe) from [<c05a844c>] (platform_drv_probe+0x34/0x70)
The cause is spi_gpio_setup() did not check if the spi-gpio has
chipselect pins before setting their direction and results in derefing
an invalid pointer.
The bug is spotted in kernel 4.19.72 and does not occur in 4.14.
There is a similar fix upstream in kernel 5.2 in commit 249e2632dcd0
("spi: gpio: Don't request CS GPIO in DT use-case").
Ref: https://patchwork.kernel.org/patch/11150619/
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[use upstream patch, moved from hack to pending dir, commit facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since service and instance names may contain characters which are not allowed
in JSON path labels, such as dashes or spaces, change the filter expression
to array square bracket notation to properly match these cases as well.
Fixes: 2c3dd70741 ("procd: add procd_running() helper for checking running state")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
5b4f7382af Add undef to fix test failure.
9456483fb2 Improve performance of memmem
373f8b06a3 Improve performance of strstr
4ec1b9e913 Fix strstr bug with huge needles (bug 23637)
ecd6271ed8 Speedup first memmem match
bba6b9288f Simplify and speedup strstr/strcasestr first match
7a4da6ef7a Improve strstr performance
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Add ath79 support for Archer C59v2, previously supported by ar71xx.
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB
Flash instruction:
- via web UI:
1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
2. Login to router and open the Advanced tab
3. Navigate to System Tools -> Firmware Upgrade
4. Upload firmware using the Manual Upgrade form
- via TFTP:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Keith Maika <keithm@aoeex.com>
The Archer C58/C59 have redundant LED and MAC address definitions
in their DTS files. This moves them to the parent DTSI file.
The patch already accounts for the upcoming Archer C59 v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Allow flashing Luxul devices using vendor firmware format. The next step
will be building proper images once they are conirmed to work.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
This makes brcmfmac use the same wiphy after PCIe reset to help user
space handle corner cases (e.g. firmware crash).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Enable by default mtk_efuse driver since it needed by mtk_thermal driver
to read sensor calibration data
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
This enables using the "eTactica" LED during boot, to indicate failsafe,
and during upgrade, while still leaving the LED alone for normal
operation. This brings the device more in line with how other devices
work, and makes the failsafe functionality easier to use and understand.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Update the ath10k-ct driver version to 5e8cd86f90dac966d12df6ece84ac41458d0e95f
to enable dynamic VLANs to work. Patches refreshed during the bump.
Signed-off-by: Robert Marko <robimarko@gmail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This enables a feature flag in the wave-2 firmware wmi-services indicating it can send
software-encrypted raw frames. This should in turn allow the AP-VLAN feature to work.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch removes scons host build tool, as commit 7087efd72a8d
("scons: move host build tool to a proper place") in the packages feed
has moved scons into the new home.
There are currently no packages in the master tree which would need
scons, yet scons is build always as part of host tools, just in order to
satisfy host build dependency of few packages in the packages feeds.
Ref: https://github.com/openwrt/packages/pull/9584
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
commit eb204d14f75c ("base-files: implement generic service_running")
introduced generic service_running so it's not needed to copy&paste same
3 lines over and over again.
I've removed service_running from netifd/network init script as well,
because it was not working properly, looked quite strange and I didn't
understand the intention:
$ /etc/init.d/network stop
$ service network running && echo "yes" || echo "nope"
( have to wait for 30s )
Command failed: Request timed out
yes
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adds a default status action for init.d scripts.
procd "service status" will return:
0) for loaded services (even if disabled by conf or dead)
3) for inactive services
4) when filtering a non-existing instance
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[rebased, cleaned up]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
