Commit Graph

189 Commits

Author SHA1 Message Date
Davide Fioravanti
c71dada926 ramips: fix lan leds for Wavlink WL-WN535K1
Previously both lan1 and lan2 leds were wrongly labelled as lan2.
Moreover they were connected to the wrong lan port.
Fixes 8fde82095b ("ramips: add support for Wavlink WL-WN535K1")

Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com>
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2023-06-25 11:02:04 +02:00
Nick Hainke
1d3e71bd97
treewide: remove files for building 5.10 kernel
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:

  find target/linux -iname '*-5.10' -exec rm -r {} \;

Further, remove the 5.10 include.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-05-12 13:02:43 +02:00
Alexey Bartenev
dc79b51533 ramips: add support for Keenetic Lite III rev. A
General specification:
SoC Type: MediaTek MT7620N (580MHz)
ROM: 8 MB SPI-NOR (W25Q64FV)
RAM: 64 MB DDR (EM6AB160TSD-5G)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Buttons: 3 button (POWER, RESET, WPS)
Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT)
Bootloader: U-Boot 1.1.3
Power: 9 VDC, 0.6 A

MAC in stock:
|-	+			|
| LAN 	| RF-EEPROM + 0x04	|
| WLAN	| RF-EEPROM + 0x04	|
| WAN 	| RF-EEPROM + 0x28	|

OEM easy installation
1. Use a PC to browse to http://my.keenetic.net.
2. Go to the System section and open the Files tab.
3. Under the Files tab, there will be a list of system
files. Click on the Firmware file.
4. When a modal window appears, click on the Choose File
button and upload the firmware image.
5. Wait for the router to flash and reboot.

OEM installation using the TFTP method
1. Download the latest firmware image and rename it to
klite3_recovery.bin.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the
firmware image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect
the PC to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address
192.168.1.2 and subnet mask 255.255.255.0.
5. Power up the router while holding the reset button pressed.
6. Wait approximately for 5 seconds and then release the
reset button.
7. The router should download the firmware via TFTP and
complete flashing in a few minutes.
After flashing is complete, use the PC to browse to
http://192.168.1.1 or ssh to proceed with the configuration.

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2023-03-27 02:09:58 +02:00
Michael Pratt
6f6d24a00a ramips: add label MAC address for EPG600 and ESR600
set label mac for the current ESR600 and new EPG600
using the board.d scripts

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Michael Pratt
4ef86c620f ramips: add support for Senao Engenius EPG600
FCC ID: A8J-EPG600

Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)

this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.

**Specification:**

  - MT7620 SOC		MIPS 24kec, 2.4 GHz WMAC, 2x2
  - RT5592N WLAN	PCI chip, 5 GHz, 2x2
  - QCA8337N Gb SW	RGMII GbE, SW P0 -- SOC P5, 5 LEDs
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 64 MB RAM		NT5TU32M16
  - UART console	J2, populated
  - USB 2.0 port	direct to SOC
  - 6 GPIO LEDs		power, 2G, 5G, wps2g, wps5g, line
  - 3 buttons		reset, wps, "reg" (registeration)
  - 4 antennas		internal omni-directional plates

NOT YET SUPPORTED: VoIP

  - Si3050-FT + Si3019-FT	Voice DAA, SPI control, PCM data
  - Phone Ports "TEL", "LINE"	RJ11, 4P2C (2 pins)

**MAC addresses:**

  MAC address labeled as MAC ADDRESS
  MACs present in both wifi cal data and uboot environment

  eth0.1/phy1	----	*:82	rf 0x4
  phy0		----	*:83	factory 0x4
  eth0.2	MAC	*:b8	"wanaddr"

**Installation:**

  Method 1: Firmware upgrade page:

    (if you cannot access the APs webpage)
    factory reset with the reset button
    connect ethernet to a computer
    OEM webpage at 192.168.0.1
    username and password 'admin'

    Navigate to gear icon, "Device Management", "Tools"
    select the factory.dlf image
    Upload and verify checksum

  Method 2: Serial to upload initramfs:

    Follow directions for TFTP recovery
    upload and boot initramfs and do a sysupgrade

**TFTP recovery:**

  Requires UART serial console, reset button does nothing

  rename initramfs-kernel.bin to 'uImageEPG600'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot with "4"
  execute `tftpboot` and `bootm` (with the load address)

**Return to OEM:**

  Images from OEM are provided, but not compatible
  with openwrt sysupgrade. So it must be modified.

  Alternatively, back up all mtd partitions before flashing

**Note on switch registers:**

  The necessary registers needed for the QCA8337 switch
  can be read from interrupted boot (tftpboot, bootm)
  by using the following lines in the switch driver ar8327.c
  in the function 'ar8327_hw_config_of'
  where 'qca,ar8327-initvals' is parsed from DTS
  before the new register values are written:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
    pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
    pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
    pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Rosen Penev
2630e5063d treewide: replace wpad-basic-wolfssl default
The newly merged mbedtls backend is smaller and has fewer ABI related
issues than the wolfSSL one.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-04 02:35:03 +01:00
Alexey Bartenev
3f201d1f8e ramips: add support for SNR-CPE-W4N-MT router
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A

Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
 "Administration/Management/Firmware update/Choose File" in vendor's
 web interface (ip: 192.168.1.10, login: Admin, password: Admin).
 Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 file by "System/Backup/Flash Firmware/Flash image..." in
 LuCI web interface (ip: 192.168.1.1, login: root, no password).
 Wait ~240 seconds.

Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
 Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
 Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
 new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2022-12-17 22:34:44 +01:00
Daniel Fuchs
794d1645b3 ramips: add support for Amped Wireless B1200EX
This device is almost identical to the already supported Edimax
EW-7476RP5, the only differences are:
- There is no mode selection slider switch on this device
- The two wireless LEDs are green instead of blue
- Model name in the CSYS header is RN10

Additional changes:
- Moved WiFi LEDs and the slider switch to the individual dt files
- Added ieee80211-freq-limit to the mt7612e radio to properly disable
  2.4GHz band on this radio

Device specifications:
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS/RESET
LED:	- WiFi 5G (green)
	- WiFi 2.4G (green)
	- Signal Strength (green)
	- Power (green)
	- WPS (green)
	- LAN (green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the WPS button
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation:
Upload the sysupgrade image via the default web interface

Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
2022-11-13 22:36:06 +01:00
Shiji Yang
7a504c151d ramips: add support for Youku X2
Specifications:
  SOC:      MT7620AN + MT7612EN
  RAM:      128 MiB DDR2
  Flash:    16 MiB (Winbond W25Q28FVFG)
  WLAN:     2.4G + 5G
  LAN:      LAN ports *2
  WAN:      WAN port *1
  USB:      USB2.0 *1
  SD Card:  MicroSD *1
  Buttons:  Reset *1
  LEDs: ethernet *3, system, usb, wlan2g, wlan5g

MAC Address:
  use        address               source
  label      54:36:9b:xx:xx:ac     lan
  lan        54:36:9b:xx:xx:ac     factory.0x0028
  wan        54:36:9b:xx:xx:ad     factory.0x002e
  wlan2g     54:36:9b:xx:xx:ae     factory.0x0004
  wlan5g     54:36:9b:xx:xx:af     factory.0x8004

Installation:
1. Apply initramfs-kernel.bin in stock firmware Web UI.
2. Install sysupgrade.bin on OpenWrt and do not retain any configuration.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 21:12:24 +01:00
Aleksander Jan Bajkowski
9226f1e419
kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.

Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....

Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
  If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
  option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
  the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC -  enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-21 13:47:01 +02:00
Rafał Miłecki
711f1a8bcb kernel: mtd: backport SafeLoader parser
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-19 07:07:14 +02:00
Sungbo Eo
b201462c89 ramips: 5.15: add disabled PINCTRL_AW9523
Otherwise kernel 5.15 will fail to build on subtargets except for mt7621
that has enabled the config.
The disabled PINCTRL_AW9523 config disappears after a refresh, it needs
to be added back manually.

Fixes: 675cf75578 ("ramips: add config-5.15 for mt7620 subtarget")
Fixes: 001176994a ("ramips: add config-5.15 for mt76x8 subtarget")
Fixes: b9d9f33c33 ("ramips: add config-5.15 for rt288x subtarget")
Fixes: 0164dc0c25 ("ramips: add config-5.15 for rt305x subtarget")
Fixes: ef59da8669 ("ramips: add config-5.15 for rt3883 subtarget")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-09-18 03:09:19 +09:00
Sungbo Eo
bcd5d35dc0 ramips: 5.15: refresh subtarget kconfigs
Refresh config with `make kernel_oldconfig`.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-09-18 03:09:19 +09:00
Daniel Golle
675cf75578 ramips: add config-5.15 for mt7620 subtarget
Add Kernel config for testing Linux 5.15 for the mt7620 subtarget.
Tested on Youku YK-L1 which boots fine.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-10 22:52:20 +01:00
Hauke Mehrtens
ff06edd1f0 kernel: Activate CONFIG_GPIOLIB in generic configuration
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-08-10 21:36:17 +02:00
David Yang
577f3fdbc9 ramips: add support for Netcore NW5212
This patch adds support for Netcore NW5212, provided by some carrier in
China.

Specifications:
--------------

* SoC: Mediatek MT7620A
* RAM: 128MB DDR2
* Flash: 16MB SPI NOR flash (Winbond W25Q128BV)
* WiFi 2.4GHz: builtin
* Ethernet: builtin
* LED: Power, WAN, LAN 1-4, WiFi
* Buttons: Reset (GPIO 13)
* UART: Serial console (57600 8n1)
* USB: 1 x USB2

Installation:
------------

The router comes with OpenWrt 14.07 built with MTK SDK. However, as the
modem is provided by carriers, so the web interface is highly minimized and
only contains a static page with no interaction options.

There are two possible ways to gain the access.

1) Open the shell and use a UART2USB convert to gain TTY access. Please
   notice you have to remove resistance R54 at the back of the board
   otherwise you won't be able to input anything.
2) Use built-in backdoor. Access http://192.168.1.1/cgi-bin/_/testxst to
   start dropbear service at port 9122. Be warned the software is super
   old and only diffie-hellman-group1-sha1, diffie-hellman-group14-sha1,
   kexguess2@matt.ucc.asn.au is support, you may not be able to connect it
   with an up-to-date ssh client.

After you can control the device, flash the firmware as usual. Here are
some hints for that.

Option 1 (via original firmware):

1) Setup HTTP server on your computer, for example:
     python3 -m http.server
2) Connect to the route and flash:
     cd /tmp
     wget http://<your-computer-host>/<your-firmware-name>
     mtd -r write <your-firmware-name> firmware

Option 2 (replacing u-boot via breed):

1) Download breed-mt7620-reset13.bin from https://breed.hackpascal.net/
2) Setup HTTP server on your computer, for example:
     python3 -m http.server
   You can skip this step if your breed is already accessible from HTTP,
   since the original wget does not support HTTPS.
3) Connect to the route and flash breed:
     cd /tmp
     wget http://<your-computer-host>/breed-mt7620-reset13.bin
     mtd write breed-mt7620-reset13.bin Bootloader
4) Reboot. Hold reset key or press any key in TTY to enter breed.
5) Access breed web interface (http://192.168.1.1/). Choose the flash
   layout to be 0x50000 and flash new firmware.

MAC addresses:
-------------

There are three MACs stored in factory, as in MT7620A reference design:

source address   usage
   0x4 label     WLAN
  0x28 label     MAC 1
  0x2e label + 1 MAC 2

However, the OEM firmware only uses one single MAC (label) for all
interfaces, probably a misconfiguration.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2022-08-06 19:58:46 +02:00
David Yang
b00a02aaa0 ramips: add support for Netgear PR2000
This patch adds support for Netgear PR2000, sold as "Travel Router and
Range Extender".

Specifications:
--------------

* SoC: Mediatek MT7620N
* RAM: 64MB DDR2
* Flash: 16MB SPI NOR flash (Macronix MX25L12805D)
* WiFi 2.4GHz: builtin
* Ethernet: builtin
* LED: Power, Internet, WiFi, USB
* Buttons: Reset (GPIO 1/2)
* UART: Serial console (57600 8n1)
* USB: 1 x USB2

SPECIAL NOTES:
-------------

Problem: WiFi is super weak, but SSID beacons seems to be right.

Solve: Change 36h in factory partition (namely 0xf60036) to be 0x0.

Explain: Clearly Netgear have different ideas on how EEPROM is used. Bit 2
of 36h indicates the presence of External LNA for 11g (2.4 GHz) band,
which seems to be incorrectly set by Netgear (originally 0x04). Lifting it
solves the problem of weak RX signal.

Installation:
------------

There are two possible ways to install the firmware. Flashing via web
interface of original firmware is not tested due to a broken firmware.

1) Open the shell and use a UART2USB convert to gain TTY access (TP7: RXD,
   TP9: TXD, TP10: GND). Please notice you have to remove resistance R54
   next to TP7 otherwise you won't be able to input anything.
2) Use well-known Netgear debug switch. Access
   http://192.168.168.1/setup.cgi?todo=debug to start telnet service
   (username: root, password: <none>).

Please back up firmware if you want to go back to the original.

After you can control the device, flash the firmware as usual. Here are
some hints for that.

Option 1 (via nmrpflash):

1) Download nmrpflash from https://github.com/jclehner/nmrpflash
2) Use *-factory.img and flash:
     nmrpflash -L
     nmrpflash -i net* -f <your-firmware-name>
3) Turn off then turn on the device, wait it finishing flash.

Option 2 (replacing u-boot via breed):

1) Download breed-mt7620-reset1.bin from https://breed.hackpascal.net/
2) Setup HTTP server on your computer, for example:
     python3 -m http.server
   You can skip this step if your breed is already accessible from HTTP,
   since the original wget does not support HTTPS.
3) Connect to the route and flash breed:
     cd /tmp
     wget http://<your-computer-host>/breed-mt7620-reset1.bin
     dd if=breed-mt7620-reset1.bin of=/dev/mtdblock0 bs=64k
4) Reboot. Hold reset key or press any key in TTY to enter breed.
5) Access breed web interface (http://192.168.1.1/). Choose memory layout
   to be 0x40000 and flash new firmware.

Remark:
------

As a "Range Extender", it has a switch to switch between Wired mode (GPIO
21 low) and Wireless mode (GPIO 20 low), which is not implemented in this
patch. However, the router will be turned off when it switches to the
middle, which makes this switch much less useful.

MAC addresses:
-------------

The OEM firmware uses one single MAC for all interfaces, located at
0xf700b0.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2022-08-06 19:58:46 +02:00
John Thomson
ef69ab7a35 kernel: cut broken SPI_NOR 4K eraseblock LIMIT patch
Since 4e0c54bc5b ("kernel: add support for kernel 5.4"),
the spi-nor limit 4k erasesize to spi-nor chips below a configured size
patch has not functioned as intended.

For uniform erasesize SPI-NOR devices, both
nor->erase_opcode & mtd->erasesize are used in erase operations.
These are set before, and not modified by, this
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS_LIMIT patch.
Thus, an SPI-NOR device with CONFIG_MTD_SPI_NOR_USE_4K_SECTORS will
always use 4k erasesize (where the device supports it).

If this patch was fixed to function as intended, there would be
cases where devices change from a 4K to a 64K erasesize.

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2022-06-29 12:34:49 +02:00
Tomasz Maciej Nowak
539e60539a generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]
This is now built-in, enable so it won't propagate on target configs.

Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-24 17:10:24 +02:00
Shiji Yang
2e6d19ee32 ramips: fix wifi mac address of HiWiFi series devices
For HiWiFi series devices, label_mac can be read from bdinfo partition,
and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac
to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's
label_mac start with D4:EE)

For example:
label	D4:EE:07:32:84:88
lan	D4:EE:07:32:84:88
wan	D4:EE:07:32:84:89
wlan2g	D4:EE:07:32:84:88
wlan5g	D0:EE:07:32:84:88

Tested on HiWiFi HC5661.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-03-26 02:02:44 +01:00
Rodolphe de Saint Léger
46c5de5385 ramips: add support for Netgear WN3100RPv2
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577

This device seems to be same hardware as a WN3000RPv3

Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
  (see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
  (preferred method).

Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
  powercycling the device

Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1

Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 23:14:25 +09:00
Sungbo Eo
fe34001ee5 Revert "ramips: add support for Netgear WN3000RPv3"
This reverts commit 7bc20cb614.

It adds support for Netgear WN3100RPv2, but the commit title is wrong.
It will be re-added with the correct title.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 23:10:45 +09:00
Rodolphe de Saint Léger
7bc20cb614 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577

This device seems to be same hardware as a WN3000RPv3

Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
  (see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
  (preferred method).

Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
  powercycling the device

Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1

Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 22:36:04 +09:00
Pawel Dembicki
be89c9eec4 ramips: mt7620: Add support for D-Link DWR-961 A1
The DWR-961 A1 Wireless Router is based on the MT7620A SoC.
It's a merge of two Amit boards: DWR-960 with ethernet part
of Lava LR-25G001.

ROMID it's taken from Telenor branded version and it works with tested
device. Images from D-Link site for this router are from DWR-953 and it
have ROMID DLK6E2424001. I don't know if it's mistake on web-site
or if it's will require different image.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612 mpcie card)
- 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem cat 6
- UART (J5) header on PCB (57600 8n1)
- 13x LED, 2x button
- JBOOT bootloader

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-03-16 22:31:14 +09:00
Petr Štetiar
fb2801b82c mt7620: fix missing kernel config symbol
Fixes following missing kernel config symbol after adding GPIO watchdog:

  Software watchdog (SOFT_WATCHDOG) [M/n/y/?] m
  Watchdog device controlled through GPIO-line (GPIO_WATCHDOG) [Y/n/m/?] y
    Register the watchdog as early as possible (GPIO_WATCHDOG_ARCH_INITCALL) [N/y/?] (NEW)

Fixes: 1a97c03d86 ("rampis: feed zbt-we1026 external watchdog")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-02-28 21:32:32 +01:00
Arvid E. Picciani
1a97c03d86 rampis: feed zbt-we1026 external watchdog
Without feeding the gpio watchdog, the board will reset after 90 seconds

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2022-02-28 15:17:11 +01:00
Davide Fioravanti
8fde82095b ramips: add support for Wavlink WL-WN535K1
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.

Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 internal antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button (set to WPS)
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 3x Green leds (ethernet port status/act)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
		16384+0 records in
	16384+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done

6) After few seconds, in the textarea should appear this output:
		384+0 records in
	384+0 records out
	128+0 records in
	128+0 records out
	128+0 records in
	128+0 records out
	14720+0 records in
	14720+0 records out
	1024+0 records in
	1024+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro
	http://192.168.10.1/dev/mtd5ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:E2 (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:E4 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:E5 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:E5

2) The OEM firmware upgrade page accepts only files containing the
   string "WN535K1" in the filename.

3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-30 01:15:23 +09:00
Kyoungkyu Park
6041c693dd ramips: add support for HUMAX E2
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
  - Switch: SoC internal
- UART: J2 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
   The device will be automatically rebooted.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
2022-01-15 20:05:46 +09:00
Sungbo Eo
482a7e23a4 ramips: add support for WeVO AIR DUO
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.

Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
  * SATA 6Gb/s: 2.5" drive slot
  * USB 3.0: Micro-B
  * USB 2.0: connected to SoC
* Wi-Fi:
  * 2.4 GHz: SoC built-in
  * 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
  * Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
  * Pinout: (3V3)|(RXD) (TXD) (GND)

Notes:
* The drive is accessible through the external USB port only when the
  router is turned off.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
    The image filename should have ".upload" extension.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-29 20:35:57 +01:00
Sergey Ryazanov
b61ab8f57e kernel: filter out both Clang and LLD versions
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sungbo Eo
cc3e390a74 ramips: mt7620: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-16 22:28:58 +09:00
Rui Salvaterra
c772783394 ramips: remove Linux 5.4 support
We're at 5.10 stable, this can finally go.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-15 09:40:03 +00:00
Pawel Dembicki
a82fa5bcd4 ramips: mt7620: Enable PHY aneg of Lava LR-25G001
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:

switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0

This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]

When switch is now ok, let's fix port numeration too.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-04 00:36:47 +01:00
Mathias Kresin
1470009bf8 kernel: 5.10: packet mangling code only for ar8216 driver
Only the ar8216 switch driver uses the packet mangling code.

Update the kernel configs accordingly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-02 22:36:41 +01:00
Jani Partanen
e06aaba4e3 ramips: fix LAVA LR-25G001 broken wifi led triggers
LED labels for this device are different in 01_leds file and in device
DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone
device.

This has not been tested on the LR-25G001 itself, just on the clone
mentioned above.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

Signed-off-by: Jani Partanen <rtfm@iki.fi>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:11:23 +02:00
Andrea Poletti
de0c380a5f ramips: add support for Sitecom WLR-4100 v1 002
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
      white triangle on PCB:

    VCC 3.3V
    GND
    TX
    RX

    baud: 115200, parity: none, flow control: none

Installation

    Connect to one of LAN (yellow) ethernet ports,
    Open router configuration interface,
    Go to Toolbox > Firmware,
    Browse for OpenWrt factory image with dlf extension and hit Apply,
    Wait few minutes, after the Power LED will stop blinking, the router is
    ready for configuration.

Known issues
Some USB 2.0 devices work at full speed mode 1.1 only

MAC addresses

factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.

  factory     0x4       **:**:**:**:b9:84  binary
  u-boot-env  ethaddr   **:**:**:**:b9:84  ascii
  u-boot-env  wanaddr   **:**:**:**:b9:85  ascii
  u-boot-env  wlanaddr  00:AA:BB:CC:DD:12  ascii
  u-boot-env  iNICaddr  00:AA:BB:CC:DD:22  ascii

The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.

Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC

Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
 setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-05 23:52:35 +02:00
David Yang
38cb500516 ramips: expose ephy leds for miwifi-mini
Give users more control by exposing ephy leds.

Signed-off-by: David Yang <mmyangfl@gmail.com>
[remove execute bit on 01_leds, add status for gpio2]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:42:17 +02:00
Shiji Yang
a73a8269e1 ramips: add support for DomyWifi DM202/DM203/DW22D
Specifications:
* SOC: MT7620A + MT7610E
* ROM: 16 MiB spi flash (W25Q128FVSG)
* RAM: 128 MiB DDR2 (W971GG6KB-25)
* WAN: 10/100M *1
* LAN: 10/100M *4
* USB: Type-A USB2.0 *1
* SD: MicroSD *1
* Button: Reset *1
* Antennas: 2.4 GHz *2 + 5 GHz *1
* TTL Baudrate: 57600
* U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3

Installation:
* Web UI Update
  1. Open http://192.168.10.1/upgrade.html in the browser.
  2. Rename firmware to a short name like firmware.bin and then upload it.
  3. Fill in the password column with the following content:
  password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware
* TFTP + U-Boot
  1. Connect device with a TTL cable.
  2. Press "2" when booting to select "Load system code then write to Flash via TFTP".
  3. Upload firmware by tftpd64, it will boot when write instruction is executed.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-08-25 01:42:16 +02:00
Shiji Yang
80e70be0ab ramips: add new flash layout support to Phicomm K2
Descriptions:
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.

OpenWrt selection table:
official firmware version           OpenWrt
v22.4.x.x or older              phicomm_k2-v22.4
v22.5.x.x or newer              phicomm_k2-v22.5

Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
   words "K2 telnet"), and then we can upload firmware image to
   /tmp and write it to firmware partition with mtd instruction.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
 in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-24 20:26:00 +02:00
David Bauer
373c08bcbb ramips: fix missing NVMEM subsystem
MAC address retrieval was switched to more generic upstream (5.13) NVMEM
based solution in commit 06bb4a5018 ("ramips: convert mtd-mac-address
to nvmem implementation") , but NVMEM subsystem wasn't enabled in the
kernel, so fix it now.

References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801
Fixes: 06bb4a5018 ("ramips: convert mtd-mac-address to nvmem implementation")
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
2021-07-21 11:39:39 +02:00
David Bauer
38db2f12d6 ramips: add AW9523 I2C GPIO expander driver
This adds a driver for the AW9523 I2C GPIO expander.

This driver is required to make LEDs as well as buttons on the Tenbay
T-MB5EU-V01 work.

This driver already had several upstream iterations. I'm working to
push this driver to mainline.

Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-06-27 21:40:15 +02:00
Michael Pratt
2adeada045 ramips: mt7620: disable SOC VLANs for external switches
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.

Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617ae)

When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.

So disable the internal switch VLANs by default on these boards.

Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.

In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-06-23 14:22:19 +08:00
Ben Gainey
a509b80065 ramips: add support for the Wavlink WL-WN579X3
About the device
----------------

SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.

Installation
------------

Using the webcmd interface
--------------------------

Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.

You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.

1. Log into the device's admin portal. This is necessary to
   authenticate you as a user in order to be able to access the
   webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
   the console directly through this page, or you may wish to
   launch the installed `telnetd` and use telnet instead.
   * Using telnet is recommended since it provides a more
     convenient shell interface that the web form.
   * Launch telnetd from the form with the command `telnetd`.
   * Check the port that telnetd is running on using
     `netstat -antp|grep telnetd`, it is likely to be 2323.
   * Connect to the target using `telnet`. The username should
     be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
   e.g.  `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
          wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
   Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
   * The flash partition should be mtd4, but check
     /sys/class/mtd/mtd4/name first. The partition should be
     called 'Kernel'.
   * To flash use the following command:
     `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
     Where mtd<n> is the Kernel partition, and <image-file> is
     the OpenWrt image previously downloaded.
   * The command above will erase, flash and then reboot the
     device. Once it reboots it will be running OpenWrt.

Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.

Using the serial port
---------------------

The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.

Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.

Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
2021-06-06 18:56:45 +02:00
Shiji Yang
4a9f389ed2 ramips: split Youku YK1 to YK-L1 and YK-L1c
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600

Descriptions:
  Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
  really different, the only hardware difference between the two models is flash
  size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
  compatible with YK-L1's firmware but it's better to split it to different models.

  It is easy to identify the models by looking at the label on the bottom of the
  device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
  sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
  to install compatible firmware, so please backup config file before system upgrade.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Shiji Yang
e57e460dc7 ramips: fix mac addresses of Youku YK1
MAC addresses read from official firmware

        value       location
Wlan    xx 71 de    factory@0x04
Lan     xx 71 dd    factory@0x28
Wan     xx 71 df    factory@0x2e
Label   xx 71 dd    factory@0x28

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-10 14:41:06 +02:00
Rui Salvaterra
3326b5e75c treewide: switch the timer frequency to 100 Hz
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:10 +01:00
Shiji Yang
882a6116d3 ramips: improve pinctrl for Youku YK-L1
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-04-10 20:48:26 +02:00
Shiji Yang
b88d2850c6 ramips: correct switch config of Youku yk1
There are only two lan ports and one wan port on Youku yk1

Fixes: e9baf8265b ("ramips: add support for Youku YK1")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-27 16:54:15 +01:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Ilya Lipnitskiy
b021642cac ramips: 5.10: refresh configs
Run-tested on Ubiquiti EdgeRouter X.

Compile tested on all other subtargets.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00