Adds support for the Wallys DR40x9 series boards.
They come in IPQ4019 and IPQ4029 versions.
IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.
Specifications are:
* CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
* RAM: 512 MB
* Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
* USB 3.0 TypeA port for users
* MiniPCI-E with PCI-E 2.0 link
* MiniPCI-E for LTE modems with only USB2.0 link
* 2 SIM card slots that are selected via GPIO11
* MicroSD card slot
* Ethernet: 2x GBe with 24~48V passive POE
* SFP port (Does not work, I2C and GPIO's not connected on hardware)
* DC Jack
* UART header
* WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
* 4x MMCX connectors for WLAN
* Reset button
* 8x LED-s
Installation instructions:
Connect to UART, pins are like this:
-> 3.3V | TX | RX | GND
Settings are 115200 8n1
Boot initramfs from TFTP:
tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb
bootm
Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>
The board file binary was provided from Wallystech on March 14th 2023
including full permission to use and distribute.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
The original claim about conflicting MAC addresses is wrong. mac80211
does increment the first octet and sets the LA bit.
This means our "workaround" actually leads to the issue while
incrementing the last octet is safe.
Signed-off-by: David Bauer <mail@david-bauer.net>
Cases have been reported in which certain devices do not boot correctly
or have errors. After various tests by users who have such errors it has
been concluded that the SPI frequency should be reduced to 40Mhz, at
this speed it appears that all devices work correctly.
Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
Manually rebased:
ramips/patches-5.10/810-uvc-add-iPassion-iP2970-support.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
Disable interrupts for the eth-PHYs, as the interrupts are either not
firing or lost within the stack. Switch to polling the PHY status in the
meantime until a proper fix is implemented.
Ref: https://github.com/openwrt/openwrt/issues/12192
Signed-off-by: David Bauer <mail@david-bauer.net>
The boot-procedure for the Extreme WS-AP3825I is vfragile to put it
mildly. It does not relocate the FDT properly. It currently exercises
every step manually as well as coming with a pre-padded dtb.
Use the PowerPC bootwrapper code for legacy platforms with a pre-filles
DTS instead. We still need to ship a fit image to not break the fdt
resize / relocate instructions on existing boards. This does not require
adapting the U-Boot bootcommand.
Ref: https://github.com/openwrt/openwrt/issues/12223
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes issues with legacy boot loaders that don't process reserved memory
regions outside of system RAM
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move it to pending, since it wasn't actually accepted upstream yet.
Fixes potential issues when doing offload between multiple MACs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall
or ceiling mountable. It can be powered via PoE, or a 12 V adapter.
The board has footprints for 2.54mm UART headers. They're difficult to
solder because the GND is connected to a large copper plane. Only try
soldering if you are very skilled. Otherwise, use pogo pins.
Specifications:
---------------
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 366 MB of RAM available to OS, not sure of total amount
* Storage: Macronix MX30UF2G18AC 256MB NAND
* Ethernet:
* 2.5G RJ45 port (QCA8081) with PoE input
* WLAN:
* 2.4GHz/5GHz with 8 antennas
* LEDs:
* Power (Amber)
* LAN (Blue)
* 2G WLAN (Blue)
* 5G WLAN (Blue)
* Buttons:
* 1x Factory reset
* Power: 12V DC Jack
* UART: Two 4-pin unpopulated headers near the LEDs
* "J2 UART" is the CPU UART, 3.3 V level
Installation:
=============
Web UI method
-------------
Flashing OpenWRT using the vendor's Web UI is problematic on this
device. The u-boot mechanism for communicating the active rootfs is
antiquated and unreliable. Instead of setting the kernel commandline,
it relies on patching the DTS partitions of the nand node. The way
partitions are patched is incompatible with newer kernels.
Newer kernels use the SMEM partition table, which puts "rootfs" on
mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One
reliable way to boot from mtd14 and avoid boot loops is to use an
initramfs image.
1. In the factory web UI, navigate to System Manager -> Firmware.
2. In the "Local Firmware Upgrade" section, click Browse
3. Navigate and select the 'web-ui-factory.fit' image
4. Click "Upload"
5. On the following page, click on "Proceed"
The flash proceeds at this point and the system will reboot
automatically to OpenWRT.
6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline
SSH method
----------
Enable SSH using the CLI or Web UI. The root account is locked out to
ssh, and the admin account defaults to Netgear's CLI application.
So we need to get creative:
First, make sure the device boots from the second firmware partition:
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 1
Then reboot the device, and run the update:
scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \
-o hostkeyalgorithms=ssh-rsa \
netgear_wax218-squashfs-nand-factory.ubi \
admin@<ipaddr>:/tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi
ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \
/usr/sbin/fw_setenv active_fw 0
Now reboot the device, and it should boot into a ready-to-use OpenWRT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Francisco G Luna <frangonlun@gmail.com>
The wrapper-image for the WL-WDR4900 was used as a build-target for the
kernel. This workd fine as long as only a single wrapper is used with
the OpenWrt build-system.
If additional wrappers are used, the build becomes racy in the
wrapper-stage.
The wrapper images actually do not represent a target. They are built
based on the kernel configuration. Only copy the resulting images to
avoid race-conditions as explained.
Signed-off-by: David Bauer <mail@david-bauer.net>
As the mac-address readout never worked, the mac-address fillout by the
bootloader is sufficient. Remove the readout for the Watchguard T10
then.
Signed-off-by: David Bauer <mail@david-bauer.net>
The mac-address accessor functions were not included in the sourced
script. Fix this by importing the correct script path.
Signed-off-by: David Bauer <mail@david-bauer.net>
Make it possible to change the kernel configuration option
CONFIG_HARDLOCKUP_DETECTOR from OpenWrt.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This sets the CONFIG_KCOV_IRQ_AREA_SIZE kernel configuration option to its default value.
This is shown when I set CONFIG_KERNEL_KCOV=y in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuration options I see when
CONFIG_KERNEL_KASAN=y is set in the OpenWrt configuration on x86/64.
Set CONFIG_STACK_HASH_ORDER to its default value.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This sets some kernel configuration options to their default values. I saw
these as warnings when I set CONFIG_KERNEL_UBSAN=y is set in the OpenWrt
configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuration options I see when
CONFIG_KERNEL_DYNAMIC_FTRACE=y is set in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuration options I see when
CONFIG_KERNEL_HIST_TRIGGERS=y is set in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuration options I see when
CONFIG_KERNEL_DEBUG_VIRTUAL=y is set in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
This deactivates some kernel configuratoion options I see when
CONFIG_KERNEL_DEBUG_VM=y is set in the OpenWrt configuration on x86/64.
Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
Hardware
--------
SoC: Qualcomm IPQ8065
RAM: 512 MB DDR3
Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB)
4 MB SPI-NOR (Macronix MX25U3235F)
WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz
Qualcomm Atheros QCA9984 - 5Ghz
ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt)
eth1 - (1000Mbps in both)
Auto-negotiation broken on both.
USB: USB 2.0
LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red)
BTN: Reset
Other: SD card slot (non-functional)
Serial: 115200bps, near the Ethernet transformers, labeled 9X.
Connections from the arrow to the 9X text:
[NC] - [TXD] - [GND] - [RXD] - [NC]
Installation
------------
0. Connect to the device
Plug your computer into LAN2 (1000Mbps connection required).
If you use the LAN1/POE port, set your computer to force a 100Mbps link.
Connect to the device via TTL (Serial) 115200n8.
Locate the header (or solder pads) labeled 9X,
near the Ethernet jacks/transformers.
There should be an arrow on the other side of the header marking.
The connections should go like this:
(from the arrow to the 9X text): NC - TXD - GND - RXD - NC
1. Prepare for installation
While the AP is powering up, interrupt the startup process.
MAKE SURE TO CHECK YOUR CURRENT PARTITION!
If you see: "Current Partition is : partB" or
"Need to switch partition from partA to partB",
you have to force the device into partA mode, before continuing.
This can be done by changing the PKRstCnt to 5 and resetting the device.
setenv PKRstCnt 5
saveenv
reset
After you interrupt the startup process again,
you should see: Need to switch partition from partB to partA
You can now continue to the next step.
If you see: "Current Partition is : partA",
you can continue to the next step.
2. Prevent partition switching.
To prevent the device from switching partitions,
we are going to modify the startup command.
set bootcmd "setenv PKRstCnt 0; saveenv; bootipq"
setenv
3. First boot
Now, we have to boot the OpenWrt intifs.
The easiest way to do this is by using Tiny PXE.
You can also use the normal U-Boot tftp method.
Run "bootp" this will get an IP from the DHCP server
and possibly the firmware image.
If it doesn't download the firmware image, run "tftpboot".
Now run "bootm" to run the image.
You might see:
"ERROR: new format image overwritten - must RESET the board to recover"
this means that the image you are trying to load is too big.
Use a smaller image for the initial boot.
4. Install OpenWrt from initfs
Once you are booted into OpenWrt,
transfer the OpenWrt upgrade image and
use sysupgrade to install OpenWrt to the device.
Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
This commit adds the PHY reset gpio for the LAN1 port to the dts.
According to the GPL sources, gpios 34 and 36 are used on the AVM
FritzBox 7320 and 7330. The second port is unsupported.
The gpio assignment has been verified on the FritzBox 7330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit includes some additional changes:
- better handling of iv and keys in openssl/wolfssl variants
- fix compiler warnings and whitespace
- build all 3 variants as separate packages
- adjust the new package name in targets' DEVICE_PACKAGES
- remove PKG_FLAGS:=nonshared
[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Make sure it uses updated Jalapeno BDF inherited from
Device/8dev_jalapeno-common
Fixes: 146eb4925c ("ipq40xx: add support for Crisis Innovation Lab MeshPoint.One")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ fix Fixes tag to correct format and fix commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set specific BDF file for 8devices Habanero/Jalapeno in ipq40xx
generic.mk
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[ split ipq40xx changes in separate commit ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add new patch sent upstream for requesting the memory region in the bcm6345-l1
interrupt controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR ()
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Upload the factory image using the Web-UI.
Web-Recovery
------------
The router supports a HTTP recovery mode by holding the reset-button
when powering on. The interface is reachable at 192.168.0.1 and supports
installation using the factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
GPIO3, to which the user LED is connected on RB911-Lite boards seems to
still sink current, even when driven high. Enabling open drain for this
pin fixes this behaviour and gets rid of the glow when LED is set to
off, so enable it.
Fixes: 43c7132bf8 ("ath79: add support for MikroTik RouterBOARD 911 Lite2/Lite5")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
