Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit acb10faa35)
Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit aa2fa2eb76)
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a7 ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a11 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 117f41ee95)
The RGB LED of the UniFi 6 LR v1 doesn't work when using the Openwrt-
built U-Boot. This is because the vendor loader resets the ledbar
controller while our U-Boot doesn't care.
Add reset-gpio so the ledbar driver in Linux will always reset the
ledbar controller.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0b5cf952cf)
This moves the ledbar driver to generic, to be also used by the ramips target.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 53fc987b25)
The LEDs connected to the MCU are so-called smart LEDs and their signal is
daisy-chained. Because of this, the MCU needs to be told how many LEDs are
connected. It also means the LEDs could be individually controlled, if the MCU
has a command for this.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 76198e8f09)
During GPIO initialization the pin state flips and triggers a reset of
the ledbar MCU. It needs to be moved through an initialization sequence
before working correctly.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 013a956f08)
Some versions of the ledbar MCU have a reset pin. It needs to be
correctly initialized or we might keep the MCU in reset state.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 84e4bbf5f0)
There are commands that return more than one byte of response.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 7c852e7df5)
Or the comparison against a signed char is always true, because the
literal 0xaa is treated as an unsigned int, to which the signed char is
casted during comparison. 0xaa is above the positive values of a signed
char and negative signed char values result in values larger than 0xaa
when casted to unsigned int.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit e9a22ce253)
The read response is in the i2c_response variable. Also use %hhx format,
because we're dealing with a single char.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit c4f9f9b44c)
Janusz Dziedzic reported a typo introduced by a recent commit. Fix it.
Fixes: 50c892d67b ("mediatek: bpi-r64: make initramfs/recovery optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 007c8809c1)
Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 50c892d67b)
Make sure the compatible string in DTS matches the now v1/v2
differentiated board name in target/linux/mediatek/image/mt7622.mk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit be555b9dd8)
Make use of minor sector size (4k) on supported SPI-NOR flash chips.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 51f4c84178)
Refresh all patches on top of kernel 5.10.138.
The following patches were applied upstream:
bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch
bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch
bcm27xx/patches-5.10/950-0346-drm-vc4-A-present-but-empty-dmas-disables-audio.patch
bcm27xx/patches-5.10/950-0354-drm-vc4-Add-the-2711-HVS-as-a-suitable-DMA-node.patch
bcm27xx/patches-5.10/950-0413-drm-vc4-hdmi-Don-t-access-the-connector-state-in-res.patch
bcm27xx/patches-5.10/950-0505-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch
bcm27xx/patches-5.10/950-0512-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch
bcm27xx/patches-5.10/950-0560-drm-vc4-drv-Remove-the-DSI-pointer-in-vc4_drv.patch
bcm27xx/patches-5.10/950-0561-drm-vc4-dsi-Use-snprintf-for-the-PHY-clocks-instead-.patch
bcm27xx/patches-5.10/950-0562-drm-vc4-dsi-Introduce-a-variant-structure.patch
bcm27xx/patches-5.10/950-0565-drm-vc4-Correct-pixel-order-for-DSI0.patch
bcm27xx/patches-5.10/950-0566-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch
bcm27xx/patches-5.10/950-0567-drm-vc4-Fix-dsi0-interrupt-support.patch
bcm27xx/patches-5.10/950-0568-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch
bcm27xx/patches-5.10/950-0647-drm-vc4-Fix-timings-for-interlaced-modes.patch
bcm27xx/patches-5.10/950-0695-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch
Upstream sets the pixel clock to 340MHz now, do not set it to 600MHz any more.
bcm27xx/patches-5.10/950-0576-drm-vc4-hdmi-Raise-the-maximum-clock-rate.patch
Fixes: 89956c6532 ("kernel: bump 5.10 to 5.10.138")
Fixes: 4209c33ae2 ("kernel: bump 5.10 to 5.10.137")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 5a81e00063 as it was
backported upstream in commit a1e238690916 ("arm64: dts: mt7622: fix
BPI-R64 WPS button").
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Due to the bug described here[1], remove the 300 MHz clock to avoid a low
voltage condition that can cause a hang when rebooting the RT3200/E8450.
This solution is probably better than the script-based work-around[2].
1. https://forum.openwrt.org/t/belkin-rt3200-linksys-e8450-wifi-ax-discussion/94302/1490
2. https://github.com/openwrt/openwrt/pull/5025
Signed-off-by: John Audia <therealgraysky@proton.me>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit d0d6b8e183)
[ fix the conflict by apply the patch to kernel 5.10 ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When building the mediatek/mt7629 target in OpenWrt 22.03 the kernel
does not have a configuration option for CONFIG_CRYPTO_DEV_MEDIATEK. Add
this option to the generic kernel configuration and also add two other
configuration options which are removed when we refresh the mt7629
kernel configuration.
Fixes: 2bea35cb55 ("mediatek: remove crypto-hw-mtk package")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dcc0fe24ea)
The recent differentiation between v1 and v2 of the UniFi 6 LR added
support for the v2 version which has GPIO-controlled LEDs instead of
using an additional microcontroller to drive an RGB led.
The polarity of the white LED, however, was inverted and the default
states didn't make a lot of sense after all. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f58e562b07)
Add targets:
* Ubiquiti UniFi 6 LR v2
* Ubiquiti UniFi 6 LR v2 (U-Boot mod)
This target does not have a RGB led bar like v1 did
Used target/linux/ramips/dts/mt7621_ubnt_unifi.dtsi as inspiration
The white dome LED is default-on, blue will turn on when the system is
in running state
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
(cherry picked from commit 31d86a1a11)
based on current ubnt_unifi-6-lr-ubootmod
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
(cherry picked from commit 5c8d3893a7)
Based on current mt7622-ubnt-unifi-6-lr, this is a preparation for
adding a v2 version of this target
* v1 - with led-bar
* v2 - two simple GPIO connected LEDs (in later commits)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
(cherry picked from commit 15a02471bb)
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit d9ea9c06e9)
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 3f2d0703b6)
Fix the wps button to prevent wrongly detected recovery procedures.
In the official banana pi r64 git the wps button is set to
GPIO_ACTIVE_LOW and not GPIO_ACTIVE_HIGH.
Import patch to fix on boot unwanted recovery entering:
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- failsafe button wps was pressed -
- failsafe -
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry-picked from commit 6686194255)
The kernel configuration option CONFIG_MACH_MT7629 selects
CONFIG_HAVE_ARM_ARCH_TIMER now. Handle this change in the config-5.10.
This fixes some build problems.
Fixes: 81530d69ef ("kernel: bump 5.10 to 5.10.121")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is not RTC battery connected to the SoC of the UniFi 6 LR board.
Disable the RTC to prevent the system coming up with time set to
2000-01-01 00:00:00 after each reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 692d87a27b)
This series also contains other improvement for hardware flow offload support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 0f029b3d2b)
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fc245338d6)
Use ARMv8 Crypto Extensions for AES, ghash and sha256.
This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit c9c2b01b84)
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
(cherry picked from commit 9f9477b275)
Some units of the Xiaomi Redmi Router AX6S/Xiaomi Router AX3200 contain this part.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
(cherry picked from commit 4177de10df)
This patch moves the patches of parser_trx in mediatek target to
generic/backport-5.10 to use the changes from ramips target and
backport the additional patch of the parser.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
X32 Pro is another product name for it in the Chinese market.
Specifications:
- SoC: MT7622B
- RAM: 256MB
- Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
- Ethernet: 5x1GbE
- Switch: MT7531BE
- WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
- 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
- 2Keys: Mesh button + Reset button
- UART: Marked J19 on board. 3.3v, 115200n1
- Power: 12V 2.5A
MAC addresses as verified by OEM firmware:
use address source
WAN *:F4 ethaddr@product_info
LAN *:F5
5g *:F6
2g *:F7
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Langhua Ye <y1248289414@outlook.com>
Enable support for allocating user space page table entries in high memory [1],
for the targets which support this feature. This saves precious low memory
(permanently mapped, the only type of memory directly accessible by the kernel).
[1] https://www.kernel.org/doc/html/latest/vm/highmem.html
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
fwtool is now always part of the sysupgrade stage2 ramdisk, so drop
the no longer needed RAMFS_COPY_BIN variable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that both, fw_printenv/fw_setenv and fwtool are always present
during stage2 sysupgrade, we no longer need to list them in
RAMFS_COPY_BIN and RAMFS_COPY_DATA in platform.sh.
Drop both variables as they are now unneeded.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Turns out the MT7531 switch IRQ line is connected to GPIO#53 just like
on the BPi-R64, so this seems to be part of the reference design and
will probably apply to most MT7622+MT7531 boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we support link-state-change interrupts, wire up MT7531 IRQ
line which is connected to GPIO#53 according to the schematics [1].
As a result, PHY state no longer needs to be polled on that board.
[1]: https://forum.banana-pi.org/t/bpi-r64-mt7622-schematic-diagram-public/10118
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
