Commit Graph

23970 Commits

Author SHA1 Message Date
Szabolcs Hubai
1e9afcca56 ramips: disable default build for HooToo HT-TM02
While the latest version of 19.07 release is usable,
the current master is unbootable on the device in a normal way.

"Normal way" installations includes:
- sysupgrade (e.g. from 19.07)
- RESET button recovery with Ron Curry's (Wingspinner) UBoot image
  (10.10.10.3 + "Kernal.bin")
- RESET button recovery with original U-Boot
  (10.10.10.254 + "kernel")

One could flash and boot the latest master sysupgrade image successfully
with serial access to the device. But a sysupgrade from this state still
breaks the U-Boot and soft-bricks the device.

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-02-07 22:06:57 +01:00
Adrian Schmutzler
1c0e13db43 ramips: mt7621: use preferred logic in lib/upgrade/iodata.sh
shellcheck recommends || and && over "-a" and "-o" because the
latter are not well defined.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-07 21:58:51 +01:00
INAGAKI Hiroshi
88fbddb49d ramips: add support for I-O DATA WN-DX1200GR
I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: raw NAND 128 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7603E
  - 5 GHz	: MediaTek MT7613BE
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/keys	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: 3.3V, TX, RX, NC, GND from triangle-mark
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using initramfs image:

1. Boot WN-DX1200GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
   to perform firmware update
4. On the initramfs image, perform sysupgrade with the
   squashfs-sysupgrade image
5. Wait ~120 seconds to complete flashing

Notes:

- currently, mt7615e driver in mt76 doesn't fully support MT7613
  (MT7663) wifi chip
  - the eeprom data in flash is not used by mt7615e driver and the
    driver reports the tx-power up to 3dBm
  - the correct MAC address for MT7613BE in eeprom data cannot be
    assigned to the phy

- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware

- stock firmware requires "customized uImage header" (called as "combo
  image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't

  - uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC")
  - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
  - image name   (0x20 - 0x37) : model ID and firmware versions
  - data length  (0x38 - 0x3b) : kernel + rootfs
  - data crc32   (0x3c - 0x3f) : kernel + rootfs

MAC addresses:

LAN:	50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex))
WAN:	50:41:B9:xx:xx:0A (Factory,  0x1E006 (hex))
2.4GHz:	50:41:B9:xx:xx:08 (Factory,  0x4     (hex))
5GHz:	50:41:B9:xx:xx:09 (Factory,  0x8004  (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add check whether dflag_offset is set]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-07 21:58:51 +01:00
Daniel González Cabanelas
07f4e3b5b2 bcm63xx: kernel: reenable the TRNG
The hardware random number generator driver for bcm63xx was merged with
the one used by the Raspberry Pi. Now this driver is lost.

Reenable the HW_RANDOM kernel config with the new driver.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[refresh kernel config]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-07 19:06:52 +01:00
Pawel Dembicki
17fa01bb79 mpc85xx: refresh kernel config
Simple "make kernel_oldconfig" was done.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-02-06 17:13:33 +01:00
Thomas Beckler
450ec48d61 kirkwood: use 3 temperature sensors for Zyxel NSA310B
Instead of taking the input of one temperature sensor (temp1), the
script takes into account three temperature sensors to control the
PWM of the cooling fan.

temp1 -> placed on main board
temp2 -> placed on main board
temp3 -> placed on or close to chipset

All three temperatures give valid input for the PWM of the fan on
NSA310 and are actually changing.

Tested on two NSA310.

Signed-off-by: Thomas Beckler <thomas.beckler@hotmail.com>
Reviewed-by: Alberto Bursi <bobafetthotmail@gmail.com>
[commit title/message facelift, code cleanup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 22:21:08 +01:00
Adrian Schmutzler
8a79161a82 ath79: wrap ucidef_add_switch in 02_network
Wrap line to be consistent with all other definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 21:57:19 +01:00
Yanase Yuki
d468ff97b7 build: move elx-header into image-commands.mk
ELECOM WAB-I1750-PS will need this in ath79, so move it to common
Makefile.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2021-02-05 21:57:19 +01:00
Sungbo Eo
321035420c kirkwood: refresh kernel config
Refresh config with make kernel_oldconfig.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-02-05 19:05:20 +01:00
Aleksander Jan Bajkowski
c9619fe6a5 lantiq: change phy-mode to mii for FRITZ!Box 7412
FRITZ!Box 7412 loads the firmware for fast ethernet PHY and mii is
more accurate in this case.
Gmii is used by Gigabit ethernet PHYs.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Reviewed-by: Mathias Kresin <dev@kresin.me>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:56:19 +01:00
Adrian Schmutzler
04a0e5c082 ipq806x: replace full-text BSC license by SPDX identifier
This replaces a full-text BSD clause by the corresponding SPDX
identifier.

This should make it easier to identify the license both by humans
and machines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:28:30 +01:00
Adrian Schmutzler
3f4d1dad00 ramips: replace full-text licenses by SPDX identifier
This replaces several full-text and abbreviated licenses found in
DTS files by the corresponding SPDX identifiers.

This should make it easier to identify the license both by humans
and machines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:18:00 +01:00
David Bentham
4a18039785 ramips: add support for UniElec U7621-01
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:

- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)

The following has been tested and is working:

- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button

Installation:

This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.

Recovery:

This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.

LEDs list (left to right):

- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)

Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 17:31:51 +01:00
Martin Kennedy
55d2db0e8c ath79: add support for Meraki MR12
Port device support for Meraki MR12 from the ar71xx target to ath79.

Specifications:

  - SoC: AR7242-AH1A CPU
  - RAM: 64MiB (NANYA NT5DS32M16DS-5T)
  - NOR Flash: 16MiB (MXIC MX25L12845EMI-10G)
  - Ethernet: 1 x PoE Gigabit Ethernet Port (SoC MAC + AR8021-BL1E PHY)
  - Ethernet: 1 x 100Mbit port (SoC MAC+PHY)
  - Wi-Fi: Atheros AR9283-AL1A (2T2R, 11n)

Installation:

  1. Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins
  2. Open shell case
  3. Connect a USB->TTL cable to headers furthest from the RF shield
  4. Power on the router; connect to U-boot over 115200-baud connection
  5. Interrupt U-boot process to boot Openwrt by running:
       setenv bootcmd bootm 0xbf0a0000; saveenv;
       tftpboot 0c00000 <filename-of-initramfs-kernel>.bin;
       bootm 0c00000;
  6. Copy sysupgrade image to /tmp on MR12
  7. sysupgrade /tmp/<filename-of-sysupgrade>.bin

Notes:

  - kmod-owl-loader is still required to load the ART partition into the
    driver.

  - The manner of storing MAC addresses is updated from ar71xx; it is
    at 0x66 of the 'config' partition, where it was discovered that the
    OEM firmware stores it. This is set as read-only. If you are
    migrating from ar71xx and used the method mentioned above to
    upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more
    method for doing this is described below.

  - Migrating directly from ar71xx has not been thoroughly tested, but
    one method has been used a couple of times with good success,
    migrating 18.06.2 to a full image produced as of this commit. Please
    note that these instructions are only for experienced users, and/or
    those still able to open their device up to flash it via the serial
    headers should anything go wrong.

    1) Install kmod-mtd-rw and uboot-envtools
    2) Run `insmod mtd-rw.ko i_want_a_brick=1`
    3) Modify /etc/fw_env.config to point to the u-boot-env partition.
       The file /etc/fw_env.config should contain:

       # MTD device   env offset  env size    sector size
       /dev/mtd1      0x00000     0x10000     0x10000

       See https://openwrt.org/docs/techref/bootloader/uboot.config
       for more details.

    4) Run `fw_printenv` to verify everything is correct, as per the
       link above.
    5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address.
    6) Manually modify /lib/upgrade/common.sh's get_image function:
       Change ...

       cat "$from" 2>/dev/null | $cmd

       ... into ...

       (
         dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes
         echo -ne '\x00\x18\x0a\x12\x34\x56'  ; # Add in MAC address
         dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest
         cat "$from" 2>/dev/null
       ) | $cmd

       ... which, during the upgrade process, will pad the image by
       128K of zeroes-plus-MAC-address, in order for the ar71xx's
       firmware partition -- which starts at 0xbf080000 -- to be
       instead aligned with the ath79 firmware partition, which
       starts 128K later at 0xbf0a0000.

    7) Copy the sysupgrade image into /tmp, as above
    8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait

    Again, this may BRICK YOUR DEVICE, so make *sure* to have your
    serial cable handy.

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[add LED migration and extend compat message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 16:56:08 +01:00
Ewan Parker
ddafcc7947 ramips: add support for Hi-Link HLK-7688A
Specifications:

  - SoC: MediaTek MT7688AN
  - RAM: 128 MB
  - Flash: 32 MB
  - Ethernet: 5x 10/100 (1x WAN, 4x LAN)
  - Wireless: built in 2.4GHz (bgn)
  - USB: 1x USB 2.0 port
  - Buttons: 1x Reset
  - LEDs: 1x (WiFi)

Flash instructions:

  - Configure TFTP server with IP address 10.10.10.3
  - Name the firmware file as firmware.bin
  - Connect any Ethernet port to the TFTP server's LAN
  - Choose option 2 in U-Boot
  - Alternatively choose option 7 to upload firmware to the built-in
    web server

MAC addresses as verified by OEM firmware:

  use   address   source
  2g    *:XX      factory 0x4
  LAN   *:XX+1    factory 0x28
  WAN   *:XX+1    factory 0x2e

Notes:

This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage.  The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.

From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM.  For those, updating
U-Boot is recommended.

Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 14:54:47 +01:00
John Audia
36c9cf3e51 kernel: bump 5.4 to 5.4.95
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Removed upstreamed patches:
 imx6: 303-ARM-dts-imx6qdl-gw52xx-fix-duplicate-regulator-namin.patch

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-04 22:07:32 +01:00
Daniel González Cabanelas
a0e0e621ca bcm63xx: sprom: override the PCI device ID
The PCI device ID detected by the wifi drivers on devices using a fallback
SPROM is wrong. Currently the chipnum is used for this parameter.

Most SSB based Broadcom wifi chips are 2.4 and 5GHz capable. But on
devices without a physical SPROM, the only one way to detect if the device
suports both bands or only the 5GHz band, is by reading the device ID from
the fallback SPROM.

In some devices, this may lead to a non working wifi on a 5GHz-only card,
or in the best case a working 2.4GHz-only in a dual band wifi card.

The offset for the deviceid in SSB SPROMs is 0x0008, whereas in BCMA is
0x0060. This is true for any SPROM version.

Override the PCI device ID with the one defined at the fallback SPROM, to
detect the correct wifi card model and allow using the 5GHz band if
supported.

The patch has been tested with the following wifi radios:

BCM43222: b43: both 2.4/5GHz working
          brcm-wl: both 2.4/5GHz working

BCM43225: b43: 2.4GHz, working
	 brcmsmac: working
	 brcm-wl: it lacks support

BCM43217: b43: 2.4GHz, working
	 brcmsmac: it lacks support
	 brcm-wl: it lacks support

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[amend commit description, rework patch to avoid using a new global variable
and keep ssb sprom extraction code as close to ssb/pci.c as possible]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-02 20:40:31 +01:00
Álvaro Fernández Rojas
e23a90674e bcm63xx: backport upstream SSB SPROM extraction
New upstream changes extract more SPROM values and fix the antenna gain.
These changes can be found in linux drivers/ssb/pci.c.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-02 20:40:29 +01:00
John Audia
d33cd383ed kernel: bump 5.4 to 5.4.94
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build-tested: bcm27xx/bcm2711, ipq806x/R7800,
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-01 19:10:43 +01:00
Leon Leijssen
eff03cea27 ath79: ag71xx: add ethtool statistics support
Add statistics to ethtool. The statistics can be useful to
debug network issues.

The code is backported from mainline ag71xx.c driver.

Signed-off-by: Leon Leijssen <leon.git@leijssen.info>
2021-02-01 00:48:12 +01:00
David Bauer
51f578efa5 ath79: add support for Ubiquiti UniFi AP Outdoor+
Hardware
--------
Atheros AR7241
16M SPI-NOR
64M DDR2
Atheros AR9283 2T2R b/g/n
2x Fast Ethernet (built-in)

Installation
------------

Transfer the Firmware update to the device using SCP.

Install using fwupdate.real -m <openwrt.bin> -d

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-01 00:47:46 +01:00
David Bauer
0c499f6068 mac80211: convert UniFi Outdoor+ HSR support to OF
Enable support for the Ubiquiti UniFi Outdoor+ RF filter via
device-tree. The old way of using platform data is not required anymore,
as it was only used on the now removed ar71xx target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-01 00:47:36 +01:00
Petr Štetiar
337ff74894 mvebu: omnia: make initramfs image usable out of the box
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree.  Fix it by producing FIT based image which could be booted with
following commands:

 setenv bootargs earlyprintk console=ttyS0,115200
 tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
 bootm ${kernel_addr_r}

Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-01-31 11:39:19 +01:00
Daniel González Cabanelas
24b910dca2 mvebu: LS421DE: fix the thermal zones
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.

Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).

In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.

(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)

Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-01-30 01:03:00 +01:00
INAGAKI Hiroshi
eb11cd9ea3 ramips: add support for ELECOM WRC-2533GHBK-I
ELECOM WRC-2533GHBK-I is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, RX, GND, TX from SoC side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-2533GHBK-I normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

MAC addresses:

LAN	: BC:5C:4C:xx:xx:89 (Config, ethaddr (text))
WAN	: BC:5C:4C:xx:xx:88 (Config, wanaddr (text))
2.4GHz	: BC:5C:4C:xx:xx:8A (Factory, 0x4    (hex))
5GHz	: BC:5C:4C:xx:xx:8B (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-01-29 15:32:07 +01:00
INAGAKI Hiroshi
0071c7cd82 build: add elecom-product-header for ELECOM devices
A header used in ELECOM WRC-300GHBK2-I and WRC-1750GHBK2-I/C is also
used in ELECOM WRC-2533GHBK-I, so split the code to generate the header
and move it to image-commands.mk to use from ramips target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-01-29 15:28:12 +01:00
Adrian Schmutzler
331892f85f treewide: drop shebang from non-executable lib files
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.

Fix execute bit in one case, too.

This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-29 14:29:41 +01:00
John Audia
2c35899d81 kernel: bump 5.4 to 5.4.93
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system:       x86_64
Build-tested:       ipq806x/R7800, bcm27xx/bcm2711
Run-tested:         ipq806x/R7800
Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon,
                    ramips/mt7621, realtek, x86/64
Run-tested [*]:     ath79/generic, ipq40xx, octeon, ramips/mt7621

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-01-29 14:22:09 +01:00
Álvaro Fernández Rojas
7d12f29ae1 bcm63xx: fix bcm63xx ethernet kernel panics
Calling netdev_reset_queue() from _stop() functions is causing sporadic kernel
panics on bcm63xx, which happen mainly on BCM6318 and BCM6328.
This reverts to the previous behaviour, which called netdev_reset_queue() from
_open() functions.

Tested on Comtrend AR-5315u (BCM6318).

Fixes: 1d6f422e34 ("bcm63xx: sync ethernet driver with net-next")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-01-28 12:01:14 +01:00
Jiang Yongquan
799fca7602 sunxi: add support for linksprite pcDuino3 nano board
Specifications:

 - SoC: Allwinner A20 @ 1Ghz
 - DRAM: 1GiB DDR3 @ 408MHz (K4B4G1646Q-HYK0)
 - NAND: 4GB MLC NAND (H27UBG8T2BTR-BC)
 - Ethernet: 10/100/1000Mbps Ethernet (Realtek RTL8211E)

Flash instructions:

dd if=openwrt-sunxi-cortexa7-linksprite_pcduino3-nano-ext4-sdcard.img
of=/dev/sdX

Signed-off-by: Jiang Yongquan <woxwchc@foxmail.com>
[Remove CONFIG_REALTEK_PHY from sunxi/cortexa53 config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-01-27 23:14:30 +01:00
Marty Jones
9c29165a4c rockchip: fix SUPPORTED_DEVICES for Radxa ROCK Pi 4
This sets SUPPORTED_DEVICES to match the compatible in the DTS.

While at it, synchronize the capitalization in DEVICE_MODEL and
DTS model.

Signed-off-by: Marty Jones <mj8263788@gmail.com>
[commit title/message facelift, move variable in armv8.mk]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
30651e6834 bcm4908: sort and wrap build recipes
This sorts the Build recipes alphabetically, wraps some long lines
and moves the DEVICE_VARS to the top like common on several other
targets.

Cc: Rafał Miłecki <rafal@milecki.pl>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
44f2d71edd mediatek: remove generic profiles
We have support for reference boards available on this target, so
support for an additional generic profile does not make much sense.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
a7904c6b7f kirkwood: remove generic profile
On a platform with many very different devices, like found on kirkwood,
the generic profile seems like a remnant of the past that does not
have a real use anymore.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
5b0644b71d ipq806x: remove generic profile
On a platform with many very different devices, like found on ipq806x,
the generic profile seems like a remnant of the past that does not
have a real use anymore.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
5697915a18 ipq40xx: remove generic profile
On a platform with many very different devices, like found on ipq40xx,
the generic profile seems like a remnant of the past that does not
have a real use anymore.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
703fd8aef4 ramips: remove generic profiles
On a platform with many very different devices, like found on ramips,
the generic profiles seem like remnants of the past that do not
have a real use anymore.

Remove them to have one thing less to maintain.

Actually, rt288x didn't have a default profile in the first place.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
9b5e9b65cf ath79: remove generic profiles
On a platform with many very different devices, like found on ath79,
the generic profiles seem like remnants of the past that do not
have a real use anymore.

Remove them to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Felix Fietkau
ff9846dbb9 ramips: use lzma-loader on zbtlink devices
Fixes boot loader LZMA decompression issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-01-27 18:26:53 +01:00
Birger Koblitz
1b1bb6bf19 realtek: add debugfs support for mirroring
This adds debugfs support to monitor mirroring via debugfs

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
6f67c079e6 realtek: add API for the hw tables of RTL83XX/93XX SoCs
Add a table API that has per accss register locking and uses
register description information to handle all table access
through a single set of api calls.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
27029277f9 realtek: add switch driver support for the RTL93XX based switches
Adds support for the RTL9300 and RTL9310 series of switches
with 10GBit per port and up to 56 ports.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
d140b9fc23 realtek: add internal and external SDS/PHYs of RTL9300 devices
This adds support for the internal SerDes of the RTL9300 SoC
and for the RTL8218D and RTL8226B phys found in combination
with this SoC in switches.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
e1bca7c77d realtek: fix RTL8231 gpio expander usage with RTL839X SoC
This fixes the usage of the RTL8231 GPIO extender chip
when used with the RTL839X SoCs. Specifically,
the PHY addresses may be different from 0.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
6aac20bc01 realtek: enable default rate limiting and qos settings
Enable default rate limiting and QoS support. Remove
previous storm control code.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
56ac4fced0 realtek: correct l2 offloading tag handling
Makes sure the DSA trailer information on any L2 offloading done
by the switch is honoured by the bridge layer

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
dc9cc0d3e2 realtek: add QoS and rate control
This adds support for identifying QoS information in packets
and use this and rate control information to submit to multiple
egress queues. The ethernet driver is also made to support
2 egress and up to 32 egress queues.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
4237488cf3 realtek: add dtsi for RTL930X SoCs
Add a default dtsi to support RTL930X SoCs.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
8faffa00cb realtek: add support for the RTL9300 timer
this adds support for the SoC timer of the RTL9300 chips, it
provides 6 independent timer/counters, of which the first one
is used as a clocksource and the second one as event timer.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
03c79ca269 realtek: add support for the RTL8390 and RTL9300 SoC IRQs
This adds support for the RTL8390 and RTL9300 SoCs
it also cleans up unnecessary definitions in mach-rtl83xx.h
and moves definitions relevant for irq routing to irq.h

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
cb39602399 realtek: add detection of RTL930X SoCs and RTL8313 SoC
This adds support to detect RTL930X based SoCs and the RTL9313 SoC.
Tested on Zyxel XGS1210-10 (RTL9302B SoC) and the
Zyxel XS1930-12 (RTL9313 SoC)

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
John Audia
9ad912d159 kernel: bump 5.4 to 5.4.92
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system:       x86_64
Build-tested:       ipq806x/R7800, bcm27xx/bcm2711
Run-tested:         ipq806x/R7800
Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon,
                    ramips/mt7621, realtek, x86/64.
Run-tested [*]:     ath79/generic, octeon, ramips/mt7621, realtek.

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-01-26 00:49:53 +01:00
Tony Ambardar
0faa172356 config: limit CONFIG_PERF_EVENTS to top-level generic configs
Remove redundant target-level settings.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-01-25 14:37:41 +01:00
Tony Ambardar
b67d086ef3 malta: update target configs and fix build warnings
Comment out some conflicting target configs that are set from subtarget
configs, which sometimes lead to kernel compile warnings:

  scripts/kconfig/conf  --syncconfig Kconfig
  net/sched/Kconfig:45: warning: menuconfig statement without prompt
  .config:1038:warning: override: CPU_MIPS32_R2 changes choice state

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-01-25 14:37:41 +01:00
Bjørn Mork
1fb413e657 realtek: build ZyXEL vendor firmware compatible initramfs
Append a device specific version trailer used by the stock
firmware upgrade application to validate firmwares.

The trailer contains a list of ZyXEL firmware version
numbers, which includes a four letter hardware identifier.
The stock web UI requires that the current hardware matches
one of the listed versions, and that the version number is
larger than a model specific minimum value. The minimum
version varies between V1.00 and V2.60 for the currently
known GS1900 models. The number is not used anywhere else
to our knowlege, and has no direct relation to the version
info in the u-image header.  We can therefore use an
arbitrary value larger than V2.60.

The stock firmware upgrade application will only load and
flash the part of the file specified in the u-image header,
regardless of file size.  It can therefore not be used to
flash images with an appended rootfs. There is therefore no
need to include the trailer in other images than the
initramfs. This prevents accidentally bricking by attempts
to flash other images from the stock web UI.

Stock images support all models in the series, listing
all of them in the version trailer.  OpenWrt provide model
specific images.  We therefore only list the single supported
hardware identifier for each image.  This eliminates the risk
of flashing the wrong OpenWrt image from stock web UI.

OpenWrt can be installed from stock firmware in two steps:

   1) flash OpenWrt initramfs image from stock web gui
   2) boot OpenWrt and sysupgrade to a squasfs image

The OpenWrt squashfs image depends on a static partition
map in the DTS.  It can only be installed to the "firmware"
partition.  This partition is labeled "RUNTIME1" in u-boot
and in stock firmware, and is referred to as "image 0" in
the stock flash management tool.  The OpenWrt initramfs
can be installed and run from either partitions. But if
you want to keep stock irmware in the spare system partition,
then you must make sure stock firmware is installed to the
"RUNTIME2" partition referred to as "image 1" in the stock
web UI. And the initial OpenWrt initramfs must be flashed
to "RUNTIME1"/"image 0".

The stock flash management application supports direct
selection of both which partition to flash and which
partition to boot next.  This allows software controlled
"dual-boot" between OpenWrt and stock firmware, without
using console access to u-boot. u-boot use the "bootpartition"
variable stored in the second u-boot environment to select
which of the two system partitions to boot.  This variable
is set by the stock flash management application, by direct
user input.  It can also be set in OpenWrt using e.g

 fw_setsys bootpartition 1

to select "RUNTIME2"/"image 1" as default, assuming a
stock firmware version is installed in that partition.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-24 18:12:34 +01:00
Bjørn Mork
ca4832fcac realtek: use vendor-specific magic for ZyXEL
The stock firmware of the ZyXEL GS1900 series use a non-standard
u-image magic.  This is not enforced by the stock u-boot, which is
why we could boot images with the default magic.  The flash
management application of the stock firmware will however verify
the magic, and refuse any image with another value.

Convert to vendor-specific value to get flash management support
in stock firmware, including the ability to upgrade to OpenWrt
directly from stock web UI.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-24 18:12:34 +01:00
Adrian Schmutzler
29167cbca3 x86: fix upgrade by emptying SUPPORTED_DEVICES
x86 uses append-metadata, but only for signing and not for the
metadata itself.

Since recently SUPPORTED_DEVICES was assigned with a global value
and is not empty anymore, append-metadata will now actually put
metadata into x86 images. This breaks sysupgrade on x86.

To fix it for the moment, let's just empty SUPPORTED_DEVICES for
this target again.

In the long term, one should either not add metadata to the images
if it is not desired, and/or remove the unintended fwtool check.

Fixes: f52081bcf9 ("treewide: provide global default for SUPPORTED_DEVICES")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 23:42:47 +01:00
Adrian Schmutzler
4571ef48d8 bcm53xx: use default SUPPORTED_DEVICES for Meraki MR32
Since the new global SUPPORTED_DEVICES are now available in bcm53xx
as well, we do not need to specify an explicit value for the MR32
anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 23:42:47 +01:00
Michael Pratt
96017a6013 ath79: add support for Senao Engenius EAP1200H
FCC ID: A8J-EAP1200H

Engenius EAP1200H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9557 SOC
  - QCA9882 WLAN	PCI card, 5 GHz, 2x2, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM	NT5TU32M16FG
  - UART at J10		populated
  - 4 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)

**MAC addresses:**

  MAC addresses are labeled as ETH, 2.4G, and 5GHz
  Only one Vendor MAC address in flash

  eth0 ETH  *:a2 art 0x0
  phy1 2.4G *:a3 ---
  phy0 5GHz *:a4 ---

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin at J10

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will brick the device
  DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

  NOTE: TFTP is not reliable due to bugged bootloader
  set MTU to 600 and try many times

**Format of OEM firmware image:**

  The OEM software of EAP1200H is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-eap1200h-uImage-lzma.bin
    openwrt-ar71xx-generic-eap1200h-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-01-23 12:53:22 +01:00
Adrian Schmutzler
f52081bcf9 treewide: provide global default for SUPPORTED_DEVICES
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:

  SUPPORTED_DEVICES := $(subst _,$(comma),$(1))

At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:

  device/image name:  vendor_model
  compatible:         vendor,model

The equal redundant definitions are a symptom of this process.

Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.

This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 12:45:21 +01:00
Bjørn Mork
402408b368 kernel: mtdsplit_uimage: replace "edimax, uimage" parser
The "edimax,uimage"" parser can be replaced by the generic
parser using device specific openwrt,partition-magic and
openwrt,offset properties.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
3f36dffbde kernel: mtdsplit_uimage: add "openwrt, offset" and "openwrt, partition-magic"
Some devices prepend a standard U-Boot Image with a vendor specific
header, having its own magic. Adding two new properties will support
validation of such images, including the additional magic.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
ff7709d223 kernel: mtdsplit_uimage: replace "netgear, uimage" parser
The "netgear,uimage" parser can be replaced by the generic
parser using device specific openwrt,ih-magic and
openwrt,ih-type properties.

Device tree properties for the following devices have not
been set, as they have been dropped from OpenWrt with the
removal of the ar71xx target:

 FW_MAGIC_WNR2000V1     0x32303031
 FW_MAGIC_WNR2000V4     0x32303034
 FW_MAGIC_WNR1000V2_VC  0x31303030
 FW_MAGIC_WPN824N       0x31313030

Tested-by: Sander Vanheule <sander@svanheule.net>  # WNDR3700v2
Tested-by: Stijn Segers <foss@volatilesystems.org> # WNDR3700v1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
de64d4b958 kernel: mtdsplit_uimage: add "openwrt, ih-type" device-tree property
Some devices use uimage headers with a non-default ih_type. Add
support for overriding this in device tree.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
647fdafcc5 kernel: mtdsplit_uimage: replace "allnet, uimage" parser
Convert users to the generic "openwrt,uimage" using device specific
"openwrt,ih-magic" properties, and remove "allnet,uimage".

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
01a1e21863 kernel: mtdsplit_uimage: replace "openwrt, okli" parser
The only difference between the "openwrt,okli" and the generic
parser is the magic.  Set this in device tree for all affected
devices and  remove the "openwrt,okli" parser.

Tested-by: Michael Pratt <mcpratt@protonmail.com> # EAP300 v2, ENS202EXT and ENH202
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
ed39f7ec1a kernel: mtdsplit_uimage: add "openwrt, ih-magic" device-tree property
Many devices use uimages with non-standard magic values. Let
device tree override the default magic.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
5ab5bacda2 kernel: mtdsplit_uimage: replace "fonfxc" and "sge" parsers
Convert users of the "fonfxc" and "sge" parsers to the generic
"openwrt,uimage", using device specific "openwrt,padding" properties.

Tested-by: Stijn Segers <foss@volatilesystems.org> [DIR-878 A1]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
76ea7a91cf kernel: mtdsplit_uimage: read extralen from device tree
An "openwrt,padding" property in device tree can replace two device
specific parsers.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
dd5ac0546c dt-bindings: mtd: partitions: add OpenWrt defined U-Boot Image
Add devicetree bindings for vendor specific variants of U-Boot
Images, as defined by OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Rafał Miłecki
20b4f77bb6 kernel: add parser finding rootfs after CFE bootfs
It's required for BCM4908. It cannot use "bcm-wfi-fw" parser because
that one requires *two* JFFS2 partitions which is untested / unsupported
on the BCM4908 architecture. With a single JFFS2 partition "bcm-wfi-fw"
parser will:
1. Fail to find "vmlinux.lz" as it doesn't follow "1-openwrt" file
2. Create partitions that don't precisely match bootfs layout

The new parser is described in details in the MTD_SPLIT_CFE_BOOTFS
symbol help message.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-22 20:14:39 +01:00
Rafał Miłecki
6ba3a0e889 bcm4908: build valid Asus GT-AC5300 firmware image
Insert Asus specific tail that is required for image identification.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-22 20:11:24 +01:00
Sieng Piaw Liew
1d6f422e34 bcm63xx: sync ethernet driver with net-next
Sync ethernet driver code with upstream Linux kernel:
-Reduce xmit_more code changes.
-Combine rx cleanup code into a function.
-Convert to build_skb.
-Improve rx loop by optimizing loop tracking.

https://lore.kernel.org/netdev/20210106144208.1935-1-liew.s.piaw@gmail.com/
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Amend commit description, move patches to the top since they are going to be
upstreamed]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-01-22 12:42:30 +01:00
Álvaro Fernández Rojas
2d8422842c bcm63xx: nand: fix OOB R/W for non Hamming ECC
Hamming ECC devices do not cover OOB data, as opposed to BCH ECC devices.
Therefore, disabling ECC for all devices is preventing BCH devices from
correctly reading and writing the OOB data.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-01-22 11:36:49 +01:00
Adrian Schmutzler
b3eccbca7c ramips: fix port labels for Xiaomi Mi Router 4
The OEM assignment of LAN ports is swapped.

Fixes: c2a7bb520a ("ramips: mt7621: add support for Xiaomi Mi Router 4")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:56:43 +01:00
Dmytro Oz
c2a7bb520a ramips: mt7621: add support for Xiaomi Mi Router 4
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).

Specifications:

Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A

UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:c2      factory 0xe000 (label)
WAN   *:c3      factory 0xe006
2g    *:c4      factory 0x0000
5g    *:c5      factory 0x8000

Flashing instructions:

1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:

setenv uart_en 1
saveenv
boot

3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/

Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion

Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:53:19 +01:00
Adrian Schmutzler
93be5926a2 ramips: mt7621: create DTSI for Xiaomi NAND devices
This creates a DTSI for Xiaomi devices with 128M NAND.

This allows to consolidate the partitions and a few other nodes for
AC2100 family and Mi Router 3G.

Note that the Mi Router 3 Pro has 256M NAND and differently sized
partitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:52:02 +01:00
Adrian Schmutzler
5a46b71826 ramips: mt7621: reorganize shared device definitions for Xiaomi
This creates a shared device definition for Xiaomi devices with
NAND and "separate" images, i.e. kernel1.bin and rootfs0.bin.

This allows to consolidate similar/duplicate code for AC2100 family
and Mi Router 3G.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:52:02 +01:00
Robert Marko
36347d003a ipq40xx: fix boards being shown twice
Since generic images have been split to their own
Makefile boards are showing up twice in menuconfig
as $(eval $(call BuildImage)) was not dropped from
the new generic.mk.

Hence $(eval $(call BuildImage)) was being called
twice.

So, lets simply drop it from generic.mk.

Fixes: 378c7ff282 ("ipq40xx: split generic images into own file")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-01-21 17:08:16 +01:00
Rafał Miłecki
3bd8f660a4 bcm4908: workaround NAND controller #WP issue
There seems to be a problem with setting #WP. On the other hand ignoring
the #WP seems to work. rootfs_data UBI volume seems to persist changes.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-21 13:30:20 +01:00
Rafał Miłecki
e78d3e44dd bcm4908: append UBI with rootfs to device images
Also enable UBI kernel support.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-21 13:25:34 +01:00
Rafał Miłecki
4e1e18af65 bcm4908: build flashable & bootable firmware images
BCM4908 bootloader requires firmware with JFFS2 image containing:
1. cferam.000
2. 94908.dtb
3. vmlinux.lz
4. device custom files

cferam.000 can be obtained from the bcm63xx-cfe repository.
device custom files are stored in images dir.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-21 13:18:42 +01:00
Rafał Miłecki
095ed5e8e1 bcm4908: set console in the CONFIG_CMDLINE
procd doesn't work with just serial specified in the DT (using chosen &
stdout-path). It requires tty device to be explicitly specified in the
cmdline.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-21 09:18:31 +01:00
Rafał Miłecki
e6fb4d08a1 bcm4908: add DTS patches for USB PHY and partitions
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 22:00:22 +01:00
Rafał Miłecki
bc3dbd68c4 bcm4908: use backported brcmstb soc stubs patch
Final version differs slightly - uses IS_ENABLED()

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 22:00:18 +01:00
Rafał Miłecki
707ad89f06 bcm4908: use backported switch & PMB DTS patches
Final versions differ slightly from what was used initially.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 22:00:15 +01:00
Rafał Miłecki
20a0d435d8 bcm4908: add pending mtd patches for BCM4908 partitioning
BCM4908 can have multiple firmware partitions. MTD needs to detect which
one is currently used.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 07:47:29 +01:00
Rafał Miłecki
7495acb555 kernel: backport mtd commit converting partitions doc syntax
1. It's useful for developing & validating DTS files inside OpenWrt
2. This will allow backporting later changes that depend on it

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 07:47:23 +01:00
John Audia
1bd005ea53 kernel: bump 5.4 to 5.4.91
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
2021-01-20 01:57:05 +01:00
Sven Eckelmann
0988e03f0e ath79: Add support for OpenMesh MR1750 v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 21:41:26 +01:00
Sven Eckelmann
ae7680dc4b ath79: Add support for OpenMesh MR1750 v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, apply shared DTSI/device node, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 21:41:26 +01:00
Adrian Schmutzler
847cda16eb ath79: make OpenMesh MR900 DTSI more general
The OpenMesh MR900 and to-be-added MR1750 family are very similar.
Make the existing MR900 DTSI more general so it can be used for
the MR1750 devices as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 21:41:25 +01:00
Adrian Schmutzler
bcb311497d ath79: consolidate common definitions for OpenMesh devices
The shared image definitions for OpenMesh devices are currently
organized based on device families. This introduces some duplicate
code, as the image creation code is mostly the same for those.

This patch thus derives two basic shared definitions that work for
all devices and only requires a few variables to be moved back to
the device definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 21:41:25 +01:00
Sven Eckelmann
4fbdadc0bf ath79: apply Engenius ECB1750 style to OpenMesh MR900 RGMII cfg
The OpenMesh MR900 is a modified version of the Exx900/Exx1750 family.
These devices are shipped with an AR803x PHY and had various problems with
the delay configuration in ar71xx. These problems are now in the past [1]
and parts of the delay configuration should now be done in the PHY only.

Just switch to the configuration of the ECB1750 to have an already well
tested configuration for ath79 with the newer kernel versions.

[1] https://github.com/openwrt/openwrt/pull/3505#issuecomment-716050292

Reported-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-01-19 15:39:36 +01:00
Sven Eckelmann
31172e53f9 ath79: Add support for OpenMesh MR900 v2
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 15:39:36 +01:00
Sven Eckelmann
e06c9eec5d ath79: Add support for OpenMesh MR900 v1
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi
* 3T3R 5 GHz Wi-Fi
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 15:39:36 +01:00
Sven Eckelmann
7b772e07ea ath79: apply Engenius EAP600 style to OpenMesh MR600 RGMII cfg
The OpenMesh MR600 is a modified version of the EAP600 family. These
devices are shipped with an AR803x PHY and had various problems with the
delay configuration in ar71xx. These problems are now in the past [1] and
parts of the delay configuration should now be done in the PHY only.

Just switch to the configuration of the EAP600 to have an already well
tested configuration for ath79 with the newer kernel versions.

[1] https://github.com/openwrt/openwrt/pull/3505#issuecomment-716050292

Reported-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-01-19 15:39:36 +01:00
Sven Eckelmann
d9a3af46d8 ath79: Add support for OpenMesh MR600 v2
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 8x GPIO-LEDs (6x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 15:39:36 +01:00
Sven Eckelmann
4b35999588 ath79: Add support for OpenMesh MR600 v1
Device specifications:
======================

* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi
* 2T2R 5 GHz Wi-Fi
* 4x GPIO-LEDs (2x wifi, 1x wps, 1x power)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
  - AR8035 ethernet PHY (RGMII)
  - 10/100/1000 Mbps Ethernet
  - 802.3af POE
  - used as LAN interface
* 12-24V 1A DC
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, make WLAN LEDs consistent, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-19 15:39:36 +01:00
John Audia
38bdff29aa kernel: bump 5.4 to 5.4.90
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
2021-01-19 15:39:36 +01:00
David Bauer
99f50a7535 ath79: rename UniFi AC kernel1 partition
These devices do not run Ubiquiti AirOS. Rename the partition to the
name used by other UniFi devices with vendor dualboot support.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-01-18 17:33:00 +01:00
David Bauer
a8a17fd223 rockchip: use stable MAC-address for NanoPi R2S
The NanoPi R2S does not have a board specific MAC address written inside
e.g. an EEPROM, hence why it is randomly generated on first boot.

The issue with that however is the lack of a driver for the PRNG.
It often results to the same MAC address used on multiple boards by
default, as urngd is not active at this early stage resulting in low
available entropy.

There is however a semi-unique identifier available to us, which is the
CID of the used SD card. It is unique to each SD card, hence we can use
it to generate the MAC address used for LAN and WAN.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-01-18 17:32:52 +01:00
Robert Marko
f4fdd8609c
ipq40xx: mikrotik: enable MikroTik platform driver
This enables the MikroTik platform driver, it enables us to parse
valuable info from hard_config including WLAN calibration data
extraction from sysfs.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:31:56 +01:00
Robert Marko
0184889088 ipq40xx: mikrotik: enable MikroTik NOR parser
Needed for SPI-NOR based MikroTik IPQ40xx devices like hAP ac2.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Robert Marko
30a92f55de ipq40xx: mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTS
This enables the new MikroTik specific partition parser.

This avoids manually specifying the MikroTik specific partitions as they
can be detected by their magic values.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Robert Marko
b779da27ef ipq40xx: add MikroTik subtarget
MikroTik devices require the use of raw vmlinux out of the self
extracting compressed kernels.

They also require 4K sectors, kernel2minor, partition parser as well as
RouterBoard platform drivers.

So in order to not add unnecessary code to the generic sub target lets
introduce a MikroTik sub target.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
John Thomson
10d057f84a ipq40xx: kernel compressed boot: reset watchdog countdown
If the watchdog is enabled, set the timeout to 30 seconds before
decompress is started.

Mikrotik ipq40xx devices running with RouterBoot have the SoC watchdog
enabled and running with a timeout that does not allow time for the
kernel to decompress and manage the watchdog.

On ipq40xx RouterBoot TFTP boot the watchdog countdown is reset before:
Jumping to kernel

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2021-01-17 14:23:05 +01:00
Robert Marko
b6461e4654 ipq40xx: arm: compressed: add appended DTB section
This adds a appended_dtb section to the ARM decompressor
linker script.

This allows using the existing ARM zImage appended DTB support for
appending a DTB to the raw ELF kernel.

Its size is set to 1MB max to match the zImage appended DTB size limit.

To use it to pass the DTB to the kernel, objcopy is used:

objcopy --set-section-flags=.appended_dtb=alloc,contents \
	--update-section=.appended_dtb=<target>.dtb vmlinux

This is based off the following patch:
c063e27e02

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Alexander Couzens
378c7ff282
ipq40xx: split generic images into own file
In preparation of the new mikrotik subtarget split the generic images
into generic.mk

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-01-17 07:16:23 +01:00
Rui Salvaterra
41b096b448 ramips: mt7621: refresh the kernel config
The removed config symbols are already enabled by the generic kernel
configuration (or by default), while the added ones are forcefully
enabled by the specific architecture.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-01-15 19:12:57 +01:00
Adrian Schmutzler
3bbdc72b53 ath79: remove USB port definition for TP-Link TL-WR810N v1
The USB port definition is only needed when it is linked to a USB
LED. Since there is none for this device, we might as well remove
the port definition.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-15 19:00:15 +01:00
Russell Senior
591a4c9ed3 ath79: Add support for Ubiquiti Bullet AC
CPU:         Atheros AR9342 rev 3 SoC
RAM:         64 MB DDR2
Flash:       16 MB NOR SPI
WLAN 2.4GHz: Atheros AR9342 v3 (ath9k)
WLAN 5.0GHz: QCA988X
Ports:       1x GbE

Flashing procedure is identical to other ubnt devices.
https://openwrt.org/toh/ubiquiti/common

Flashing through factory firmware
1. Ensure firmware version v8.7.0 is installed.
   Up/downgrade to this exact version.
2. Patch fwupdate.real binary using
   `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \
    hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using
   `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
(copied from Ubiquiti NanoBeam AC and modified)

Flashing from serial console
1. Connect serial console (115200 baud)
2. Connect ethernet to a network with a TFTP server, through a
   passive PoE injector.
3. Press a key to obtain a u-boot prompt
4. Set your TFTP server's ip address, with:
   setenv serverip <tftp-server-address>
5. Set the Bullet AC's ip address, with:
   setenv ipaddr <bullet-ac-address>
6. Set the boot file, with:
   setenv bootfile <name-of-initramfs-binary-on-tftp-server>
7. Fetch the binary with tftp:
   tftpboot
8. Boot the initramfs binary:
   bootm
9. From the initramfs, fetch the sysupgrade binary, and flash it with
   sysupgrade.

The Bullet AC is identified as a 2WA board by Ubiquiti. As such, the UBNT_TYPE
must match from the "Flashing through factory firmware" install instructions
to work.

Phy0 is QCA988X which can tune either band (2.4 or 5GHz). Phy1 is AR9342,
on which 5GHz is disabled.  It isn't currently known whether phy1 is
routed to the N connector at all.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2021-01-15 18:32:38 +01:00
Sungbo Eo
583e39e3d5 kernel: drop empty kmod-ledtrig-* packages
The following four led triggers are enabled in generic config.

* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer

Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-01-15 18:24:31 +01:00
Sungbo Eo
8451f47b1e treewide: do not disable LED triggers in target config
Those targets have already enabled some other LED triggers, so enabling
a few more won't be a big problem.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-01-15 18:22:45 +01:00
Sungbo Eo
22061b2880 kernel: enable CONFIG_LEDS_TRIGGER_HEARTBEAT
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.

This increases uncompressed kernel size by about 100 bytes on ath79/generic.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-01-15 18:20:55 +01:00
Jan Alexander
05707e6460 ipq806x: fix Ubiquiti UniFi AC HD partition map
This fixes a typo in the previously committed partition map that led to
the extension of the read-only mtd partition "SSD" into the following
partitions.

Fixes: 4e46beb313 ("ipq806x: add support for Ubiquiti UniFi AC HD")

Signed-off-by: Jan Alexander <jan@nalx.net>
2021-01-15 17:34:04 +01:00
John Audia
945a704fab kernel: bump 5.4 to 5.4.89
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
2021-01-15 17:29:41 +01:00
Rafał Miłecki
c40006e0af bcm4908: prepend kernel images with a custom header
It's required for CFE to accept kernel.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-15 07:45:19 +01:00
Rafał Miłecki
6c90999e2e bcm4908: backport brcmstb USB PHY driver changes
This includes BCM4908 support

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-14 12:34:20 +01:00
Etan Kissling
39add246c1 nf-conntrack: allow querying conntrack info in nfqueue
This allows libnetfilter_queue to access connection tracking information
by requesting NFQA_CFG_F_CONNTRACK. Connection tracking information is
provided in the NFQA_CT attribute.
CONFIG_NETFILTER_NETLINK_GLUE_CT enables the interaction between
nf_queue and nf_conntrack_netlink. Without this option, trying to access
connection tracking information results in "Operation not supported".

Signed-off-by: Etan Kissling <etan_kissling@apple.com>
2021-01-14 00:52:49 +00:00
Jan Alexander
6738b5e2ac uboot-envtools: add support for Aruba AP-303 and AP-365
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.

Signed-off-by: Jan Alexander <jan@nalx.net>
2021-01-14 01:04:02 +01:00
Jan Alexander
4e46beb313 ipq806x: add support for Ubiquiti UniFi AC HD
Hardware
--------

SoC:   Qualcomm IPQ8064
RAM:   512MB DDR3
Flash: 256MB NAND (Micron MT29F2G08ABBEAH4)
       32MB SPI-NOR (Macronix MX25U25635F)
WLAN:  Qualcomm Atheros QCA9994 4T4R b/g/n
       Qualcomm Atheros QCA9994 4T4R a/n/ac
ETH:   eth0 - SECONDARY (Atheros AR8033)
       eth1 - MAIN (Atheros AR8033)
USB:   USB-C
LED:   Dome (white / blue)
BTN:   Reset

Installation
------------

Copy the OpenWrt sysupgrade image to the /tmp directory of the device
using scp. Default IP address is 192.168.1.20 and default username and
password are "ubnt".

SSH to the device and write the bootselect flag to ensure it is booting
from the mtd partition the OpenWrt image will be written to. Verify the
output device below matches mtd partition "bootselect" using /proc/mtd.

> dd if=/dev/zero bs=1 count=1 seek=7 conv=notrunc of=/dev/mtd11

Write the OpenWrt sysupgrade image to the mtd partition labeled
"kernel0". Also verify the used partition device using /proc/mtd.

> dd if=/tmp/sysupgrade.bin of=/dev/mtdblock12

Reboot the device.

Back to stock
-------------

Use the TFTP recovery procedure with the Ubiquiti firmware image to
restore the vendor firmware.

Signed-off-by: Jan Alexander <jan@nalx.net>
2021-01-14 01:03:54 +01:00
Rafał Miłecki
7e4f055990 bcm4908: backport BCM4908 integrated switch initial support
Upstream driver supports bridging ports. There is no support for
crossbar setup or CPU port(s) yet.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-13 11:28:41 +01:00
Rafał Miłecki
56d64d8b5a bcm4908: backport PMB (Power Management Bus) driver
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-13 07:44:04 +01:00
Rafał Miłecki
524b9aeb4c bcm4908: add simple PCIe reset controller support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-12 23:27:29 +01:00
Rafał Miłecki
712258b772 bcm4908: backport upstream DTS patches
1. Netgear R8000P DTS file
2. NAND fix
3. PCIe reset block
4. Integrated switch
5. PMB block

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-12 23:07:10 +01:00
Rafał Miłecki
c578fdfc29 bcm4908: initial work on the Broadcom BCM4908 target
BCM4906, BCM4908 and BCM49408 are SoCs with 64 bit ARMv8 B53 CPUs.
Upstream Linux is slowly getting support for that SoCs family so it
makes sense to add target for it.

This prepares initial support for:

1. Asus GT-AC5300
BCM4908 based device (4 CPUs) with 1024 MiB RAM, NAND, 8 LAN ports.

2. Netgear R8000P
BCM4906 based device (2 CPUs) with 512 MiB RAM, NAND, 4 LAN ports.

Flashing info will come later as we learn how to generate proper images.

It isn't usable yet (it only produces a bootable kernel) so "source-only"
is used.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-12 21:10:51 +01:00
Nick Hainke
a1a7f3274e kernel: enable SRv6 support by enabling lwtunnel
Enable the ability to use segment routing based on IPv6. It allows the
packet to specify a path that the packet should take through the
network.

Lwtunnel allow an easy encapsulation of a package. You can just install
ip-full package and use it:

  ip -6 route add  2003::/64 dev eth0 encap seg6 mode encap \
    segs 2001::1,2002::2

An IPv6 package looks like this:
  [IPv6 HDR][IPv6 RH][IPv6 HDR][Data...]

Netifd support:
  https://git.openwrt.org/?p=project/netifd.git;
     a=commit;h=458b1a7e9473c150a40cae5d8be174f4bb03bd39

Increases imagesize by 24.125 KiB. Therefore, only enable for devices
with enough flash.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-01-11 11:09:05 -10:00
David Bauer
b1150de9e4 rockchip: add missing Kconfig symbols
When compiling with CONFIG_ALL_KMODS enabled, compilation might stall
due to unset rockchip-specific config symbols. Disable these to avoid
stalling this step.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-01-11 06:00:49 +01:00
John Audia
4ebec0b3e2 kernel: bump 5.4 to 5.4.87
All modification by update_kernel.sh.

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Compile-tested [*]: ath79/{generic,tiny}, ipq40xx, octeon,
                    ramips/mt7621, realtek, x86/64.
Run-tested [*]:     ramips/mt7621 (DIR-878 A1, R6800, RT-AC57U),
                    octeon (EdgeRouter Lite).

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-01-08 21:09:17 +01:00
Stijn Segers
c4bfe68c83 realtek: add support for ZyXEL GS1900-8HP v1 and v2
The ZyXEL GS1900-8HP is an 8 port gigabit switch with PoE+ support.
There are two versions on the market (v1 & v2) which share similar
specs (same flash size and flash layout, same RAM size, same PoE+ power
envelope) but have a different case and board layout that they each
share with other GS1900 siblings.

The v1 seems to share its PCB and case with non-PoE GS1900-8; as such,
adding support for the GS1900-8 would probably be trivial. The v2 seems
to share its casing and platform with its already supported bigger
brother, the GS1900-10HP - its board looks the same, except for two
holes where the GS1900-10 has its SFP ports.

Like their 10 port sibling, both devices have a dual firmware layout.
Both GS1900-8HP boards have the same 70W PoE+ power budget. In order to
manipulate the PoE+, one needs the rtl83xx-poe package [1].

After careful consideration it was decided to go with separate images
for each version.

Specifications (v1)
-------------------
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Nanya NT5TU128M8HE-AC 128 MiB DDR2 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* PoE+:      Broadcom BCM59111KMLG (IEEE 802.3at-2009 compliant, 2x)
* UART:      1 serial header with populated standard pin connector on the
             left side of the PCB, towards the bottom. Pins are labeled:
             + VCC (3.3V)
             + TX
             + RX
             + GND

Specifications (v2)
-------------------
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Samsung K4B1G0846G 128 MiB DDR3 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* PoE+:      Broadcom BCM59121B0KMLG (IEEE 802.3at-2009 compliant)
* UART:      1 angled serial header with populated standard pin connector
             accessible from outside through the ventilation slits on the
             side. Pins from top to bottom are clearly marked on the PCB:
             + VCC (3.3V)
             + TX
             + RX
             + GND

Serial connection parameters for both devices: 115200 8N1.

Installation
------------
Instructions are identical to those for the GS1900-10HP and apply both
to the GS1900-8HP v1 and v2 as well.

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
  image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
  > rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only boot off the first partition anyway (hardcoded in the DTS). To
  make sure we are manipulating the first partition, issue the following
  commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
  > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-initramfs-kernel.bin
  > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
  > sysupgrade /tmp//tmp/openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-squashfs-sysupgrade.bin

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[merge PoE case, keep device definitions separate, change all those
hashes in the commit message to something else so they don't get
removed when changing the commit ...]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-08 20:48:22 +01:00
Adrian Schmutzler
40ea2fea4f realtek: remove model prefix from LED label for ZyXEL GS1900
This is used as fixed status LED, so no migration is needed.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-08 20:39:02 +01:00
Stijn Segers
0542cb6a2b realtek: introduce shared DTSI for GS1900 series
The ZyXEL GS1900-8HP v1, v2 and GS1900-10HP are all built on a similar
Realtek RTL8380M platform. Create a common DTSI in preparation for
GS1900-8HP support, and switch to the macros defined in rtl838x.dtsi.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[drop redundant includes, use &mdio directly, do not replace SFP
ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-08 20:39:02 +01:00
Leon M. George
211fed5f49 ramips: remove trailing whitespace in Makefiles
Remove trailing whitespaces in two *.mk files.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix title, add message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-07 19:51:50 +01:00
Stijn Segers
e1f5ffa48c realtek: ZyXEL: spell as done by manufacturer
ZyXEL spells its own name all uppercase with just the Y lowercase. Adapt
the realtek target to follow this (other OpenWrt targets already do so).

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-01-07 19:51:50 +01:00
Stijn Segers
5bdf50d13b realtek: move memory node to device DTS
Move the memory out of the rtl838x.dtsi and into the device family DTSI
or device DTS if applicable. This aligns with upstream practice.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[add missing block for dgs-1210-10p, move block below chosen node]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-07 19:51:50 +01:00
Adrian Schmutzler
5f958cb21f realtek: remove duplicate '/dts-v1/;' identifier
The identifier is already present in rtl838x.dtsi, and adding it
twice is not only redundant but actually wrong.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-07 19:51:50 +01:00
Stijn Segers
ac16e6b2ea realtek: set PoE power budget for ZyXEL GS1900-10HP
As per the manufacturer's specifications, set the GS1900-10HP PoE power
budget to 77W.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-01-07 19:51:50 +01:00
Michael Pratt
51360a913b ath79: make Engenius fakeroot partitions read-only
For:

 - ENH202 v1
 - ENS202EXT v1

These boards were committed before it was discovered
that for all Engenius boards with a "failsafe" image,
forcing the failsafe image to load next boot
can be achieved by editing the u-boot environment like:

  `fw_setenv rootfs_checksum 0`

So it's not necessary to delete a partition to boot to failsafe image.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-01-07 19:51:50 +01:00
Michael Pratt
0070650df4 ath79: move small-flash Engenius boards to tiny
This moves some of the Engenius boards from generic to tiny:

 - EAP350 v1
 - ECB350 v1
 - ENH202 v1

For these, factory.bin builds are already failing on master
branch because of the unique situation for these boards:

 - 8 MB flash
 - an extra "failsafe" image for recovery
 - TFTP does not work (barely possible with 600 MTU)
 - bootloader loads image from a longer flash offset
 - 1 eraseblock each needed for OKLI kernel loader and fake rootfs
 - using mtd-concat to make use of remaining space...

The manual alternative would be removing the failsafe partition.
However this comes with the risk of extremely difficult recovery
if a flash ever fails because TFTP on the bootloader is bugged.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[improve commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-07 19:51:50 +01:00
Koen Vandeputte
ecded5bf09 imx6: disable unrequired pcie host driver
imx6 has it's own pcie host driver so we do
not need the one from DW.

This fixes following boot error:

[    0.156913] dw-pcie 1ffc000.pcie: IRQ index 1 not found

Fixes: 6d5291ff72 ("imx6: add support for kernel 5.4")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2021-01-07 12:08:31 +01:00
Koen Vandeputte
87bd940536 imx6: refresh kernel config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2021-01-07 12:08:31 +01:00
Koen Vandeputte
7b3dd33c20 imx6: gw52xx: fix duplicate regulator naming
2 regulator descriptions carry identical naming.

This leads to following boot warning:
[    0.173138] debugfs: Directory 'vdd1p8' with parent 'regulator' already present!

Fix this by renaming the one used for audio.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2021-01-07 12:08:31 +01:00
Adrian Schmutzler
849d4b3940 ipq806x: add space before SPDX identifier (again)
Strictly, an SPDX identifier requires a space between the comment
marker and the identifier itself. This has been addressed in
b69c21738e ("treewide: add space before SPDX identifier"), but
some new malformatted identifiers were merged recently.

This could have been prevented by using checkpatch.pl earlier.

Fixes: 1a775a4fd0 ("ipq806x: add support for TP-Link Talon AD7200")
Fixes: 8ddaeaf642 ("ipq806x: create DTSI for TP-Link AD7200 and C2600")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-06 23:53:25 +01:00
Adrian Schmutzler
b039f76f35 ipq806x: improve model name and revision for TP-Link AD7200
The TP-Link AD7200 appears with and without the "Talon" model name
prefix. Let's use both variants for 'make menuconfig' so everybody
can locate the device.

Concerning the revision, the TP-Link page lists v1 and v2 with the
device currently marked as "End of Life". However, the v2 and latest
v1 firmware are byte-identical. Thus, we only need one image for
this device and do not need to include the revision in the image name.

While at it, remove the useless BOARD_NAME variable which only makes
sense in combination with upgrade from legacy stable versions or when
custom upgrade scripts are involved.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-06 14:43:12 +01:00
Adrian Schmutzler
8ddaeaf642 ipq806x: create DTSI for TP-Link AD7200 and C2600
Both devices share most of their setup except buttons and LEDs,
so having a common DTSI removes a lot of duplicate code.

In order to have a shared partitioning scheme, device-id and
product-info from AD7200 have been merged into a single
product-info partition like for C2600.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-06 14:43:12 +01:00
Adrian Schmutzler
8050b70514 ipq806x: clean up DTS file for TP-Link AD7200
This does several cosmetic adjustments for AD7200's DTS:

 - Make node name, DT label and label property consistent
 - Drop wrong and unused spi4 label
 - Use generic flash@0 node name

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-06 14:43:12 +01:00
David Bauer
b4c0d377f6 ramips: limit 5GHz channels for UniFi 6 Lite
The MT7915 radio currently advertises 2.4GHz channels while the antenna
path only supports 5 GHz. Limit the radio to 5GHz channels to prevent
users from configuring non-supported channels.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-01-06 00:00:01 +01:00
Birger Koblitz
89f71ebb35 realtek: fix build issues
This fixes the build problems for the REALTEK target by adding a proper
configuration option for the phy module.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
2021-01-05 22:43:40 +01:00
Daniel Golle
f4c64937cf ipq806x: fix LED names of TP-Link Talon AD2700
While the underscore in the name of the USB LEDs was removed from DTS,
/etc/board.d/01_leds also has to reflect that change.

Fixes: 28fd279e5d ("ipq806x: some corrections for TP-Link Talon AD7200")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-01-05 16:26:44 +00:00