Technicolor TG582n Telecom Italia branded a.k.a.
Telecom Italia ADSL2+ Wi-Fi N (AGTWI)
has the same PCB as the unbranded Technicolor TG582n with LEDs
connected to different GPIO PINs in active low configuration and
different LED names. It has a PCB similar to the OpenWrt's ADB P.DG A4001N1 one.
Hardware:
* Board ID: DANT-V
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - EtronTech EM68B16CWQD-25H
* Serial flash: 16 Mbyte - Spansion FL 128SAIF00
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x ADSL, 2x Internet, 2x Wi-Fi, 2x Service, 4x ethernet
* Buttons: 1x Reset, 1x WPS (named WiFi/LED)
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
PCB: |GPIO: |TG582n: |AGTWI:
LED2R |488(08) |red Power |red Power
LED2G |484(04) |green Power |green Power
LED10R |486(06) | |missing R85 end LED
LED13G |485(05) |green Ethernet |green ADSL
LED11R |494(14) | |red Internet
LED14G |491(11) |green Broadband |green Internet
LED5R |487(07) |red Internet |red Wi-Fi
LED5G |481(01) |green Internet |green Wi-Fi
LED12R |498(18) | |red Service
LED12G |499(19) | |green Service
LED6R |482(02) |red Wi-Fi |missing R108 end LED
LED6G |483(03) |green Wi-Fi |missing R107 end LED
LED7R |490(10) |red WPS |missing R91 end LED
LED7G |489(09) |green WPS |missing R92 end LED
LED4 |508(28) |ethernet port 4 |ethernet port 4
LED3 |507(27) |ethernet port 3 |ethernet port 3
LED9 |506(26) |ethernet port 2 |ethernet port 2
LED8 |505(25) |ethernet port 1 |ethernet port 1
SW3 |503(23) |key Reset |key Reset
SW5 |504(24) |key WPS |key Wi-Fi/LED
SW4 |495(15) |key Wi-Fi |missing R127 end key
SW6 |493(13) | |missing R171 end key
SW1 |492(12) | |missing R1 end key
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[DT fixes, base-files fixes and device variant]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This sets the --cross-compile-prefix option when running Configure, so
that that it will not use the host gcc to figure out, among other
things, compiler defines. It avoids errors, if the host 'gcc' is
handled by clang:
mips-openwrt-linux-musl-gcc: error: unrecognized command-line option
'-Qunused-arguments'
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
ADB P.DG A4101N A-000-1A1-AE has a similar PCB as the OpenWrt's ADB P.DG A4001N1
with LEDs connected to different GPIO PINs in active low configuration.
Hardware:
* Board ID: 96328avngv
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25
* Serial flash: 16 Mbyte - Winbond 25Q128BVFG
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43225 Wireless Network Adapter (rev 23)
* LEDs: 1x Power, 1x DSL, 1x Internet, 4x ETH, 1x USB, 1x WLAN, 1x WPS, 1x TEL
* Buttons: 1x Reset, 1x WPS, 1x unnamed
* UART: 1x TTL 115200n8, VCC RX TX GND, on J502 connector
Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
.bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the cfe boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file
A4101N GPIO LAYOUT:
Power always on
DSL GPIO483(03)
Internet GPIO491(11)
ETH1 GPIO505(25)
ETH2 GPIO506(26)
ETH3 GPIO507(27)
ETH4 GPIO508(28)
USB GPIO490(10)
WLAN controlled by BCM43225
WPS GPIO489(09)
TEL GPIO511(31)
Key RESET GPIO503(23)
Key WPS GPIO504(24)
Key unnamed GPIO492(12)
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Amend commit description, DTS improvements, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
faed29a dhcpv6: only refresh timers when reconfigure is valid
9c50975 dhcpv6: fix printing identity association id
a7b2221 dhcpv6: avoid sending continuous renew/rebind messages
d7afa2b dhcpv6: add extra syslog info traces
f5728e4 odhcp6c_find_entry: exclude priority from the list of fields that must match
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
On non-GNU systems, zcat often does not handle gzip decompression.
Use gzip -dc like the regular unpack command
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds support for the D-Link DSL-2750u rev C1.
(https://deviwiki.com/wiki/D-Link_DSL-2750U_rev_C1)
It uses the same hardware as ADB P.DG A4001N.
CPU: Broadcom BCM63281 (320 MHz)
RAM: 32M (Winbond W9725G6JB)
Flash: 8M (MXIC MX25L6445E)
Ethernet: 4x 100 Mbps
Wireless: 802.11b/g/n: BCM43225
USB: 1x 2.0
Flash instructions:
1. Assign static IP 192.168.1.100 to PC
2. Unplug the power source
3. Press the RESET button at the router, don't release it yet!
4. Plug the power source.Wait some seconds
5. Release the RESET button
6. Browse to http://192.168.1.1
7. Send the openwrt-bcm63xx-generic-DSL2750U-C1-squashfs-cfe.bin and
wait some minutes until the firmware upgrade finish.
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
[DTS improvements, proper board patch, refresh patches]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
ADB P.DG A4001N A-000-1A1-AX a.k.a. Telecom Italia ADSL2+ Wi-Fi N (AGPWI)
is a Telecom Italia braded router and it seems that there are no public
available unbranded versions of this router.
The stock Telecom Italia braded firmware has many partitions and the
partition layout changes with every firmware relase.
The PSI nvram partition is present in the stock firmware under the
"UNKNOWN" name but it's empty, full of FFs. Since removing partitions
does not cause problems with the stock firmware reflashing procedure,
I removed from the dts the PSI nvram partition from OpenWrt, expanded
the rootfs one and added the NVRAM partition contained in the
cfe bootloader.
Furthermore this router's flash needs to be entirely reprogrammed
and a new generic bcm6328 cfe must be flashed to boot OpenWrt. The
same process takes place when reflashing the stock firmware.
Here follows the original flash layout for AGPWI_1.1.0_013, the last
stock Telecom Italia braded firmware for which we have root
credentials (admin/riattizzati).
Flash layout:
Section 00 Type BOOT Range 0x00000000-0x00020000 MaxSize 0x00020000
No more information.
Section 01 Type IMAGE Range 0x00020000-0x007C0000 MaxSize 0x0079FF6C
Uninitialized.
Section 02 Type IMAGE Range 0x00800000-0x00FA0000 MaxSize 0x0079FF6C
Uninitialized.
Section 03 Type CONF Range 0x00FA0000-0x00FC0000 MaxSize 0x0001FF6C
Size 0x0000841E Name 'rg_conf'
Checksum 0x0041E03B Counter 0x0000051F Start Offset 0x00000000
Section 04 Type CONF Range 0x00FC0000-0x00FE0000 MaxSize 0x0001FF6C
Size 0x0000838E Name 'rg_conf'
Checksum 0x00419A5A Counter 0x00000522 Start Offset 0x00000000
Section 05 Type FACTORY Range 0x00FE0000-0x00FF0000 MaxSize 0x0000FF6C
Size 0x00000554 Name 'rg_factory'
Checksum 0x0001255E Counter 0x000004D3 Start Offset 0x00000000
Section 06 Type UNKNOWN Range 0x00FF0000-0x01000000 MaxSize 0x00010000
No more information.
Total 7 sections found.
The last AGPWI firmware relase should be AGPWI_4.0.6 and it has much more
partitions than AGPWI_1.1.0_013.
The cfe partition in the stock firmware is 0x00020000 bytes long unlike the
OpenWrt dts in wich it's 0x00010000 bytes long because from 0x00010000 to
0x00020000 in the stock cfe there are only 00s and also because the cfe must
anyway be reflashed with a generic bcm6328 cfe 0x00010000 bytes long to
run OpenWrt.
Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Amend commit, remove unneeded cfe_nvram partition]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This ports support for the TP-Link TL-WDR7500 v3 from ar71xx to ath79.
The basic features appear to be identical to the Archer C7 v1, however
it has the (supported) QCA9880-BR4A chip of the C7 v2.
Specifications:
SoC: QCA9558
CPU: 720 MHz
Flash: 8 MiB
RAM: 128 MiB
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac
Qualcomm Atheros QCA9880-BR4A
Ethernet: 5x Gbit ports
USB: 2x 2.0 ports
Flashing instructions:
Upload the factory image via the OEM firmware GUI.
TFTP recovery appears to be available as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All modifications made by update_kernel.sh/no human intervention needed
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[another refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The first gpio controller (gpio or gpio0) is always enabled by
default in the SoC DTSI files. No need to set status=okay in the
device DTS files a second time.
Remove the redundant statements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
None of the spi drivers on ath79 uses the num-cs property.
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
Some x86_64 single board computer (including Atomic Pi)
has onboard emmc, but requires CONFIG_MMC_SDHCI_ACPI driver
to use or boot from it.
Here is boot message for the mmc device
[ 2.838008] mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
[ 2.857536] mmc1: SDHCI controller on ACPI [80860F14:01] using ADMA
[ 2.950019] mmc0: new HS200 MMC card at address 0001
[ 3.158271] mmcblk0: mmc0:0001 M52516 14.6 GiB
[ 3.170290] mmcblk0boot0: mmc0:0001 M52516 partition 1 4.00 MiB
[ 3.177191] mmcblk0boot1: mmc0:0001 M52516 partition 2 4.00 MiB
[ 3.183963] mmcblk0rpmb: mmc0:0001 M52516 partition 3 4.00 MiB, \
chardev (248:0)
Other lines changed in this config file are introduced by menuconfig.
Signed-off-by: Mengyang Li <mayli.he@gmail.com>
The include/trusted-firmware-a.mk file is based on the
include/u-boot.mk file and should be used to build a Trusted Firmware-A
(TFA) which was previously named Arm trusted firmware.
This is useful for targets where the TFA is board specific like for
Marvell SoCs and probably also NXP Layerscape SoCs.
This also makes use of this abstraction in the
arm-trusted-firmware-mvebu package to build board specific ATF binaries.
The ATF binaries will be automatically activated and build when the
board is selected in the normal build or all boards are selected. This
should also activate the build when build bot creates images.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove the MDIO reset from the MAC mode for the AR934x SoC family.
The reset is currently also defined for the MDIO node, where the reset
is acquired exclusively.
In case the ethernet node is enabled, this triggers a warning, as the
reset is already acquired by the MAC.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TPLink CPE devices CPE210/CPE510 based on ar9344 have a build-in
Low Noise Amplifier on both of the 2x2 mimo rx chains.
This patch activates those two LNAs in the respective receiving chains
and hence improves the RX sensitivity by about 20dB.
Tested on CPE510 v2 & v3.
Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Acked-by: Robert Marko <robimarko@gmail.com>
d6bd1047d004 vlandev: dump vlan id in device status
e0c838bd06a6 vlandev: support bridge-vlan aliases in the vid config parameter
574dc4a17105 system-dummy: print configured mac address
14f0e8ff928f system-linux: simplify mask check in system_if_apply_settings
524310276f20 system-linux: move device settings handling to device.c
42c48866f1c1 config: parse default mac address from board.json
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In this new setup the switch is treated as wan, lan1.100 is used as
our mgmt vlan.
The board mac is applied to eth0, switch and switch.1
The board mac is assigned with the LA bit set to all lan ports while
incrementing it.
Signed-off-by: John Crispin <john@phrozen.org>
Add code for setting mac addresses inside board.json and rendering
them out to uci. On switches we want to have a unique MAC on each port.
With 48 port switches that would require 48 device sections in
/etc/config/network. Doing so via board.json is easier.
Signed-off-by: John Crispin <john@phrozen.org>
Some Git hoster (e.g. sr.ht) disable hosting of svg images (xml) to
avoid XSS attacks. To show the logo correctly on all code hosters use a
"safe" PNG image.
Also move logo(s) to include/ folder to lower autocomplete churn with
the `logs/` folder. While at it, replace absolute logo path and make it
relative, as this may break other code hosters as well.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Because the bug described in FS#2428 has been fixed with bf2870c1d9
("kernel: fix mtd partition erase < parent_erasesize writes") these
devices can now safely do sysupgrade.
Restore sysupgrade support disabled in:
0cc87b3bac ("ath79: image: disable sysupgrade images for routerstations
and ja76pf2")
cc5256a8bf ("ath79: base-files: disable sysupgrade for routerstations
and ja76pf2")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[move Build block, remove check-size argument, wrap sysupgrade line,
make commit message easier to read]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This will explain what is actually occuring on dd invocations.
Additionally remove comments for steps which are described by printed
statements anyway.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This will explain what is actually occuring on dd invocations.
Additionally remove comments for steps which are described by printed
statements anyway.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Similar to the previous commit adding a check to the init script of
umdns, do a similar change for sysntpd, just to be on the safe side.
Inspired-by: 520403cd49 ("umdns: add check for seccomp list")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This should fix an issue when user have a router with enabled seccomp
and tries to run umdns package which was build with SDK with disabled
seccomp support.
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
This fixes tethering with devices using iOS 14. Prior to this patch,
connections to remote endpoints were not possible while data transfers
between the OpenWrt device and the iOS endpoints worked fine.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a cell_density option to configure data rates for normal, high and
very high cell density wireless deployments.
The purpose of using a minimum basic/mandatory data rate that is higher
than 6 Mb/s, or 5.5 Mb/s (802.11b compatible), in high cell density
environments is to transmit broadcast/multicast data frames using less
airtime or to reduce management overheads where significant co-channel
interference (CCI) exists and cannot be avoided.
Caution: Without careful design and validation, configuration of a too
high minimum basic/mandatory data rate can sacrifice connection stability
or disrupt the ability to reliably connect and authenticate for little to
no capacity benefit. This is because this configuration affects the
ability of clients to hear and demodulate management, control and
broadcast/multicast data frames.
Deployments that have not been specifically designed and validated are
usually best suited to use 6, 12 and 24 Mb/s as basic/mandatory data
rates.
Only usually seek to configure a 12 Mb/s, or 11 Mb/s (802.11b
compatible), minimum basic/mandatory rate in high cell density
deployments that have been designed and validated for this.
For many deployments, the minimum basic/mandatory data rate should not be
configured above 12 Mb/s to 18 Mb/s, 24 Mb/s or higher. Such a
configuration is only appropriate for use in very high cell density
deployment scenarios.
A cell_density of Very High (3) should only be used where a deployment
has a valid use case and has been designed and validated specifically for
this use, nearly always with highly directional antennas - an example
would be stadium deployments. For example, with a 24 Mb/s OFDM minimum
basic/mandatory data rate, approximately a -73 dBm RSSI is required to
decode frames. Many clients will not have roamed elsewhere by the time
that they experience -73 dBm and, where they do, they frequently may not
hear and be able to demodulate beacon, control or broadcast/multicast
data frames causing connectivity issues.
There is a myth that disabling lower basic/mandatory data rates will
improve roaming and avoid sticky clients. For 802.11n, 802.11ac and
802.11ax clients this is not correct as clients will shift to and use
lower MCS rates and not to the 802.11b or 802.11g/802.11a rates that are
able to be used as basic/mandatory data rates.
There is a myth that disabling lower basic/mandatory data rates will
ensure that clients only use higher data rates and that better
performance is assured. For 802.11n, 802.11ac and 802.11ax clients this
is not correct as clients will shift around and use MCS rates and not the
802.11b or 802.11g/802.11a rates that able to be used as basic/mandatory
data rates.
Cell Density
0 - Disabled (Default)
Setting cell_density to 0 does not configure data rates. This is the
default.
1 - Normal Cell Density
Setting cell_density to 1 configures the basic/mandatory rates to 6, 12
and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower
than the minimum basic/mandatory rate are not offered.
Setting cell_density to 1 configures the basic/mandatory rates to the 5.5
and 11 Mb/s DSSS rates where legacy_rates is 1. Supported rates lower
than the minimum basic/mandatory rate are not offered.
2 - High Cell Density
Setting the cell_density to 2 configures the basic/mandatory rates to the
12 and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower
than the minimum basic/mandatory rate are not offered.
Setting the cell_density to 2 configures the basic/mandatory rates to the
11 Mb/s DSSS rate where legacy_rates is 1. Supported rates lower than the
minimum basic/mandatory rate are not offered.
3 - Very High Cell Density
Setting the cell_density to 3 configures the basic/mandatory rates to the
24 Mb/s OFDM rate where legacy_rates is 0. Supported rates lower than the
minimum basic/mandatory rate are not offered.
Setting the cell_density to 3 only has effect where legacy_rates is 0,
else this has the same effect as being configured with a cell_density of 2.
Where specified, the basic_rate and supported_rates options continue to
override both the cell_density and legacy_rates options.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
