As of upstream Linux commit 0fe1e96fef0a ("powerpc/pci: Prefer PCI
domain assignment via DT 'linux,pci-domain' and alias"), the PCIe
domain address is no longer numbered by the lowest 16 bits of the PCI
register address after a fallthrough. Instead of the fallthrough, the
enumeration process accepts the alias ID (as determined by
`of_alias_scan()`). This causes e.g.:
9000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11)
9000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ...
to become
0000:00:00.0 PCI bridge: Freescale Semiconductor Inc P1020E (rev 11)
0000:01:00.0 Network controller: Qualcomm Atheros AR958x 802.11abgn ...
... which then causes the sysfs path of the netdev to change,
invalidating the `wifi_device.path`s enumerated in
`/etc/config/wireless`.
One other solution might be to migrate the uci configuration, as was
done for mvebu in commit 0bd5aa89fc ("mvebu: Migrate uci config to
new PCIe path"). However, there are concerns that the sysfs path will
change once again once some upstream patches[^2][^3] are merged and
backported (and `CONFIG_PPC_PCI_BUS_NUM_DOMAIN_DEPENDENT` is enabled).
Instead, remove the aliases and allow the fallthrough to continue for
now. We will provide a migration in a later release.
This was first reported as a Github issue[^1].
[^1]: https://github.com/openwrt/openwrt/issues/10530
[^2]: https://lore.kernel.org/linuxppc-dev/20220706104308.5390-1-pali@kernel.org/t/#u
[^3]: https://lore.kernel.org/linuxppc-dev/20220706101043.4867-1-pali@kernel.org/Fixes: #10530
Tested-by: Martin Kennedy <hurricos@gmail.com>
[Tested on the Aerohive HiveAP 330 and Extreme Networks WS-AP3825i]
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
If the RTC module is compiled as a module, the hctosys fails to
initialize because ds1307 is loaded later.
Fixes:
[ 2.004145] hctosys: unable to open rtc device (rtc0)
[ 11.957997] rtc-ds1307 0-006f: registered as rtc0
This is similar to commit 5481ce9a11,
which was done for imx6 target.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
In subtarget p2020, there wasn't enabled nand support, and because of
that there weren't available tools from mtd-utils package, which has
utilities for NAND flash memory even though reference board, which
is the only currently supported device in p2020 subtarget has NAND [1].
All subtargets in mpc85xx has already enabled nand support, let's do it
globally.
[1] https://www.nxp.com/design/qoriq-developer-resources/p2020-reference-design-board:P2020RDB
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
All Freescale processors used in this target are capable to detect error
and correction. [1] It can not be used as kernel module. [2] This is
helpful to report hardware errors.
It enables three kernel options:
- EDAC, which is a subsystem
- EDAC_LEGACY_SYSFS, it enables sysfq nodes
- MP85XX, support for Freescale MPC8349, MPC8560, MPC8540, MPC8548, T4240
EDAC is already enabled for following targets:
qoriq, octeon, octeontx and zynq.
[1] https://cateee.net/lkddb/web-lkddb/EDAC.html
[2] https://patchwork.ozlabs.org/patch/554908/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
In commit 7e614820a8 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.
Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.
Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.
This change fixes Github issue #9779 [1].
[1]: https://github.com/openwrt/openwrt/issues/9779
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
The bootloader does seem to not correctly patch in the MAC address for
eth0 / eth1 in some cases. While the root cause is not known, manually
applying the MAC-Address in preinit does not hurt.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
The WS-AP3825i uses Atheros PHYs which according to the datasheet
require the reset to be asserted for at least 1 ms.
This fixes broken eth1 upon soft-reboot. eth0 is no affected, as the
ifup / ifdown cycle in preinit prevents this issue from happening when
the system is ready.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
As the LED controller is working now, we can make good use of the LEDs
now.
- Drop the model-name prefix
- Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such
on the casing
- Enable wired LEDs in userspace
Signed-off-by: David Bauer <mail@david-bauer.net>
Move the GPIO extender to the SoC node. Otherwise, the legacy PowerPC
init code will not populate the BUS and thus never probe spi-gpio.
Signed-off-by: David Bauer <mail@david-bauer.net>
Buildbot has reported following issue while crunching mpc85xx/p1010
subtarget:
Extreme Networks WS-AP3825i (WS_AP3825I) [N/y/?] (NEW)
Fix it by disabling that config symbol in target kernel config and while
at it fix DTS whitespace issue.
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware:
- SoC: Freescale P1020
- CPU: 2x e500v2 @ 800MHz
- Flash: 64MiB NOR (1x Intel JS28F512)
- Memory: 256MiB (2x ProMOS DDR3 V73CAG01168RBJ-I9H 1Gb)
- WiFi1: 2.4+5GHz abgn 3x3 (Atheros AR9590)
- Wifi2: 5GHz an+ac 3x3 (Qualcomm Atheros QCA9890)
- ETH: 2x PoE Gigabit Ethernet (2x Atheros AR8035)
- Power: 12V (center-positive barrel) or 48V PoE (active or passive)
- Serial: Cisco-compatible RJ45 next to 12V power socket (115200 baud)
- LED Driver: TI LV164A
- LEDs: (not functioning)
- 2x Power (Green + Orange)
- 4x ETH (ETH1 + ETH2) x (Green + Orange)
- 2x WiFi (WiFi2 + WiFi1)
Installation:
1. Grab the OpenWrt initramfs <openwrt-initramfs-bin>, e.g.
openwrt-mpc85xx-p1020-extreme-networks_ws-ap3825i-initramfs-kernel.bin.
Place it in the root directory of a DHCP+TFTP server, e.g. OpenWrt
`dnsmasq` with configuration `dhcp.server.enable_tftp='1'`.
2. Connect to the serial port and boot the AP with options
e.g. 115200,N,8. Stop autoboot in U-Boot by pressing Enter after
'Scanning JFFS2 FS:' begins, then waiting for the prompt to be
interrupted. Credentials are identical to the one in the APs
interface. By default it is admin / new2day: if these do not work,
follow the OEM's reset procedure using the reset button.
3. Set the bootcmd so the AP can boot OpenWrt by executing:
```uboot
setenv boot_openwrt "cp.b 0xEC000000 0x2000000 0x2000000; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go;"
setenv bootcmd "run boot_openwrt"
saveenv
```
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
```uboot
setenv ipaddr <ipv4 client address>;
setenv serverip <tftp server address>;
tftpboot 0x2000000 <openwrt-initramfs-bin>;
interrupts off;
bootm start 0x2000000;
bootm loados;
fdt resize;
fdt boardsetup;
fdt chosen;
bootm prep;
bootm go;
```
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
```ash
sysupgrade /tmp/<openwrt-sysupgrade-bin>
```
Notes:
- We must step through the `bootm` process manually to avoid fdt
relocation. To explain: the stock U-boot (and stock Linux) are configured
with a very large CONFIG_SYS_BOOTMAPSZ (and the device's stock Linux
kernel is configured to be able to handle it). The U-boot version
predates the check for the `fdt_high` variable, meaning that upon fdt
relocation, the fdt can (and will) be moved to a very high address; the
default appears to be 0x9ffa000. This address is so high that when the
Linux kernel starts reading the fdt at the beginning of the boot process,
it encounters a memory access exception and panics[5]. While it is
possible to reduce the highest address the fdt will be relocated to by
setting `bootm_size`, this also has the side effect of limiting the
amount of RAM the kernel can use[3].
- Because it is not relocated, the flattened device tree needs to be
padded in the build process to guarantee that `fdt resize` has
enough space.
- The primary ethernet MAC address is stored (and set) in U-boot; they are
shimmed into the device tree by 'fdt boardsetup' through the
'local-mac-address' property of the respective ethernet node, so OpenWrt
does not need to set this at runtime. Note that U-boot indexes the
ethernet nodes by alias, which is why the device tree explicitly aliases
ethernet1 to enet2.
- LEDs do not function under OpenWrt. Each of 8 LEDs is connected to an
output of a TI LV164A shift register, which is wired to GPIO lines and
operates through bit-banged SPI. Unfortunately, I am unable to get the
spi-gpio driver to recognize the `led_spi` device tree node at all, as
confirmed by patching in printk messages demonstrating
spi-gpio.c::spi_gpio_probe never runs. It is possible to manually
articulate the shift register by exporting the GPIO lines and stepping
their values through the sysfs.
- Though they do not function under OpenWrt, I have left the pinout details
of the LEDs and shift register in the device tree to represent real
hardware.
- An archive of the u-boot and Linux source for the AP3825i (which is one
device of a range of devices code-named 'CHANTRY') be found here[1].
- The device has an identical case to both the Enterasys WS-AP3725i and
Adtran BSAP-2030[2] (and potentially other Adtran BSAPs). Given that
there is no FCC ID for the board itself (only its WLAN modules), it's
likely these are generic boards, and even that the WS-AP3725i is
identical, with only a change in WLAN card. I have ordered one to confirm
this.
- For additional information: the process of porting the board is
documented in an OpenWrt forum thread[4].
[1]: magnet:?xt=urn:btih:f5306a5dfd06d42319e4554565429f84dde96bbc
[2]: https://forum.openwrt.org/t/support-for-adtran-bluesocket-bsap-2030/48538
[3]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/29
[4]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168
[5]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/26
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
the Aerohive HiveAP-330 and HiveAP-350 come equipped
with an TI TMP125 temperature chip. This patch wires
up the necessary support for this sensor and exposes
it through hwmon / thermal sensor framework. Upstream
support is coming, but it has to go through hwmon-next
first.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
include the device-tree binding headers that provide definitions
for keys codes and gpios in the device-tree files.
Random bonus: merge tl-wdr4900-v1's uboot with the nvmem-node.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
silences the following message:
> eeprom 0-0051: eeprom driver is deprecated, please use at24 instead
The chip was likely a Dallas Semiconductor and later MAXIM part
before Analog Devices, Inc. bought MAXIM.
From the datasheet:
"The DS28CN01 combines 1024 bits of EEPROM with challenge-and-response
authentication security implemented with the FIPS 180-1/180-2 and
ISO/IEC 10118-3 Secure Hash Algorithm (SHA-1)."
...
"Write Access Requires Knowledge of the Secret
and the Capability of Computing and Transmitting
a 160-Bit MAC as Authorization"
OpenWrt doesn't use it. There's no in-kernel driver
from what I know. Let's document that the chip is
at the location.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The tricolor LED which is controlled by a lp5521 needed
some maintenance as the driver failed to load in the
current v5.10 image:
| lp5521: probe of 0-0032 failed with error -22
This is because the device-tree needed to be updated
to match the latest led coloring and function trends.
- removed the device name from the label
- added color/function properties
- added required reg and cells properties
For reference a disabled multicolor/RGB is added since this
reflects the real hardware. Unfortunately, the multicolor
sysfs interface isn't supported by yet.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too
large upon decompression (>7MB or so) to decompress itself on boot (see
FS#4110[1]).
There have been many attempts to fix booting from a compressed kernel on
the HiveAP-330:
- b683f1c36d ("mpc85xx: Use gzip compressed kernel on HiveAP-330")
- 98089bb8ba ("mpc85xx: Use uncompressed kernel on the HiveAP-330")
- 26cb167a5c ("mpc85xx: Fix Aerohive HiveAP-330 initramfs image")
We can no longer compress the kernel due to size, and the stock bootloader
does not support any other types of compression. Since an uncompressed
kernel no longer fits in the 8MiB kernel partition at 0x2840000, we need to
patch u-boot to autoboot by running variable which isn't set by the
bootloader on each autoboot.
This commit repartitions the HiveAP, requiring a new COMPAT_VERSION,
and uses the DEVICE_COMPAT_MESSAGE to guide the user to patch u-boot,
which changes the variable run on boot to be `owrt_boot`; the user can
then set the value of that variable appropriately.
The following has been documented in the device's OpenWrt wiki page:
<https://openwrt.org/toh/aerohive/hiveap-330>. Please look there
first/too for more information.
The from-stock and upgrade from a previous installation now becomes:
0) setup a network with a dhcp server and a tftp server at serverip
(192.168.1.101) with the initramfs image in the servers root directory.
1) Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted. If the password
doesn't work. Try reseting the device by pressing and holding the reset
button with the stock OS.
2) Once in U-Boot, set the new owrt_boot and tftp+boot the initramfs image:
Use copy and paste!
# fw_setenv owrt_boot 'setenv bootargs \"console=ttyS0,$baudrate\";bootm 0xEC040000 - 0xEC000000'
# save
# dhcp
# setenv bootargs console=ttyS0,$baudrate
# tftpboot 0x1000000 192.168.1.101:openwrt-mpc85xx-p1020-aerohive_hiveap-330-initramfs-kernel.bin
# bootm
3) Once openwrt booted:
carefully copy and paste this into the root shell. One step at a time
# 3.0 install kmod-mtd-rw from the internet and load it
opkg update; opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=y
# 3.1 create scripts that modifies uboot
cat <<- "EOF" > /tmp/uboot-update.sh
. /lib/functions/system.sh
cp "/dev/mtd$(find_mtd_index 'u-boot')" /tmp/uboot
cp /tmp/uboot /tmp/uboot_patched
ofs=$(strings -n80 -td < /tmp/uboot | grep '^ [0-9]* setenv bootargs.*cp\.l' | cut -f2 -d' ')
for off in $ofs; do
printf "run owrt_boot; " | dd of=/tmp/uboot_patched bs=1 seek=${off} conv=notrunc
done
md5sum /tmp/uboot*
EOF
# 3.2 run the script to do the modification
sh /tmp/uboot-update.sh
# verify that /tmp/uboot and /tmp/uboot_patched are good
#
# my uboot was: (is printed during boot)
# U-Boot 2009.11 (Jan 12 2017 - 00:27:25), Build: jenkins-HiveOS-Honolulu_AP350_Rel-245
#
# d84b45a2e8aca60d630fbd422efc6b39 /tmp/uboot
# 6dc420f24c2028b9cf7f0c62c0c7f692 /tmp/uboot_patched
# 98ebc7e7480ce9148cd2799357a844b0 /tmp/uboot-update.sh <-- just for reference
# 3.3 this produces the /tmp/u-boot_patched file.
mtd write /tmp/uboot_patched u-boot
3) scp over the sysupgrade file to /tmp/ and run sysupgrade to flash OpenWrt:
sysupgrade -n /tmp/openwrt-mpc85xx-p1020-aerohive_hiveap-330-squashfs-sysupgrade.bin
4) after the reboot, you are good to go.
Other notes:
- Note that after this sysupgrade, the AP will be unavailable for 7 minutes
to reformat flash. The tri-color LED does not blink in any way to
indicate this, though there is no risk in interrupting this process,
other than the jffs2 reformat being reset.
- Add a uci-default to fix the compat version. This will prevent updates
from previous versions without going through the installation process.
- Enable CONFIG_MTD_SPLIT_UIMAGE_FW and adjust partitioning to combine
the kernel and rootfs into a single dts partition to maximize storage
space, though in practice the kernel can grow no larger than 16MiB due
to constraints of the older mpc85xx u-boot platform.
- Because of that limit, KERNEL_SIZE has been raised to 16m.
- A .tar.gz of the u-boot source for the AP330 (a.k.a. Goldengate) can
be found here[2].
- The stock-jffs2 partition is also removed to make more space -- this
is possible only now that it is no longer split away from the rootfs.
- the console-override is gone. The device will now get the console
through the bootargs. This has the advantage that you can set a different
baudrate in uboot and the linux kernel will stick with it!
- due to the repartitioning, the partition layout and names got a makeover.
- the initramfs+fdt method is now combined into a MultiImage initramfs.
The separate fdt download is no longer needed.
- added uboot-envtools to the mpc85xx target. All targets have uboot and
this way its available in the initramfs.
[1]: https://bugs.openwrt.org/index.php?do=details&task_id=4110
[2]: magnet:?xt=urn:btih:e53b27006979afb632af5935fa0f2affaa822a59
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(rewrote parts of the commit message, Initramfs-MultiImage,
dropped bootargs-override, added wiki entry + link, uboot-envtools)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This moves bootargs-append support patch from ipq40xx and ipq806x to
generic. This way we can append additional boot arguments from DTS instead
of only being able to overwrite them.
This is a preparation for kirkwood support of ipTIME NAS1.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
We actually need to enclose the whole section of partitions in a
`partitions { ... }` to assign it a `compatible = "fixed-partitions";
otherwise the partition referred to by `hwinfo` won't be registered
when bringing up MTD partitions, for example as per:
- <https://forum.openwrt.org/t/tp-link-c2600-missing-default-mac-mtd-partition-in-snapshot/103945/6>
- commit e2b03c16eb ("ipq806x: add missing enclosing partitions block for TP-Link C2600")'
Fixes: 8ec21d6bb2 ("mpc85xx: convert mtd-mac-address to nvmem implementation")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[minor beautification]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Martin Kennedy reported:
|Presently, I get this kernel panic on mpc85xx (Aerohive HiveAP 370)
|on OpenWrt 'master' which occurs right as the second processor is
|initialized:
|
|[ 0.478804] rcu: Hierarchical SRCU implementation.
|[ 0.535569] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
|[ 0.627233] smp: Bringing up secondary CPUs ...
|[ 0.681659] kernel tried to execute user page (0) - exploit attempt? (uid: 0)
|[ 0.766618] BUG: Unable to handle kernel instruction fetch (NULL pointer?)
|[ 0.848899] Faulting instruction address: 0x00000000
|[ 0.908273] Oops: Kernel access of bad area, sig: 11 [#1]
|[ 0.972851] BE PAGE_SIZE=4K SMP NR_CPUS=2 P1020 RDB
|[ 1.031179] Modules linked in:
|[ 1.067640] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.80 #0
|[ 1.139507] NIP: 00000000 LR: c0021d2c CTR: 00000000
|[ 1.199921] REGS: c1051cf0 TRAP: 0400 Not tainted (5.10.80)
|[...]
|[ 1.758220] NIP [00000000] 0x0
|[ 1.794688] LR [c0021d2c] smp_85xx_kick_cpu+0xe8/0x568
|[ 1.856126] Call Trace:
|[ 1.885295] [c1051da8] [c0021cb8] smp_85xx_kick_cpu+0x74/0x568 (unreliable)
|[ 1.968633] [c1051de8] [c0011460] __cpu_up+0xc0/0x228
|[ 2.029038] [c1051e18] [c0031bbc] bringup_cpu+0x30/0x224
|[ 2.092572] [c1051e48] [c0031f3c] cpu_up.constprop.0+0x180/0x33c
|[..]
|[ 2.727952] ---[ end trace 9b796a4bafb6bc14 ]---
|[ 3.800879] Kernel panic - not syncing: Fatal exception
|[ 3.862353] Rebooting in 1 seconds..
|[ 5.905097] System Halted, OK to turn off power
|
|I bisected this down to commit 3ae5da5adc ("kernel: bump 5.10 to 5.10.80");
|that is, I don't get the panic right before this commit, but I do after.
He reported the issue upstream and Xiaoming Ni from huawei came up with
the patch (that is on it's way to upstream). While the AP370 is not in
Openwrt, this will likely affect other SMP P1020 devices OpenWrt ships
with: like the AP330, Enterasys WS-AP3710i, etc.
Reported-by: Martin Kennedy <hurricos@gmail.com>
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This has testing support for 7 months. Time to switch.
TL-WDR4900 is disabled due to kernel size limitation.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Three missing symbols were found during mpc85xx/p2020 compilation.
While at it, CONFIG_FSL_ENETC_MDIO is moved to generic config
for consistency.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[move CONFIG_FSL_ENETC_MDIO, remove redundant definitions, adjust
commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.
This should make simplify the conversion of target to nvmem implementation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also add a new kconfig symbol (CONFIG_KCMP) to the generic config,
disabling the SYS_kcmp syscall (it was split from
CONFIG_CHECKPOINT_RESTORE, which is disabled by default, so the
previous behaviour is kept).
Removed (upstreamed) patches:
070-net-icmp-pass-zeroed-opts-from-icmp-v6-_ndo_send-bef.patch
081-wireguard-device-do-not-generate-ICMP-for-non-IP-pac.patch
082-wireguard-queueing-get-rid-of-per-peer-ring-buffers.patch
083-wireguard-kconfig-use-arm-chacha-even-with-no-neon.patch
830-v5.12-0002-usb-serial-option-update-interface-mapping-for-ZTE-P685M.patch
Manually rebased patches:
313-helios4-dts-status-led-alias.patch
104-powerpc-mpc85xx-change-P2020RDB-dts-file-for-OpenWRT.patch
Run tested:
ath79 (TL-WDR3600)
mvebu (Turris Omnia)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
At this moment driver start fail with error:
[ 3.771991] fsl,elbc-fcm-nand: probe of ffa00000.nand failed with error -22
elbc-fcm-nand driver use legacy method of ecc mode detection. It detect hw/sw
ecc mode when system configure it to "none". [1]
This patch adds 'nand-ecc-mode = "none"' propoerty to use generic driver
ecc mode detection.
[1] https://elixir.bootlin.com/linux/v5.10.18/source/drivers/mtd/nand/raw/fsl_elbc_nand.c#L730
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
At this moment p2020rdb has broken images, because NOR memory connected
to eLBC bus isn't detected.
In 642b1e8dbed7 linux tree commit, config dependencies of MTD_PHYSMAP_OF
was changed and now MTD_PHYSMAP is required.
This patch adds MTD_PHYSMAP option to kernel config in p2020 subtarget
and fix booting of p2020rdb.
Fixes: 13b1db795f ("mpc85xx: add support for kernel 5.4")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
When converting the fdt binary to be created as an artifact, the image
receipt was dropped but the entry in the target images list was not.
Fixes commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage")
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested on: Sophos RED 15W
The TP-Link WL-WDR4900 needs to be disabled when 5.10 becomes the
default kernel.
When building with all kmods enabled, the resulting kernel image
exceeds the maximum size the bootloader reads from the flash.
For more information, see GitHub issue #1773
Signed-off-by: David Bauer <mail@david-bauer.net>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Manually rebased patches:
bcm27xx:
patches-5.4/950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
bcm53xx:
patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
layerscape:
patches-5.4/802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
patches-5.4/808-i2c-0002-MLK-10893-i2c-imx-add-irqf_no_suspend.patch
patches-5.4/820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch
Removed since could be reverse-applied by quilt:
mediatek:
patches-5.4/0700-arm-dts-mt7623-add-missing-pause-for-switchport.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64
Run-tested: ipq806x/R7800, x86_64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64]
Rebase of 802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
We use 5.4 on all targets by default, and 4.19 has never been released
in a stable version. There is no reason to keep it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.
Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
AR8327 datasheet[1] calls the register at address 0x0010
"Power-on Strapping Register". As it has nothing to do with "strip",
let's rename it to "POWER_ON_STRAP" to make it easier to grasp.
[1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mpc85xx-generic subtarget supports the QorIQ SoCs of the p1010
family. Rename the subtarget to reflect this affiliation as it's the
case with the other mpc85xx subtargets.
Signed-off-by: David Bauer <mail@david-bauer.net>
Most targets upstream use 250Hz or even 1000Hz by default while
100Hz is hardcoded in OpenWrt's default config. Use upstream default
except for apm821xx which hardsets 1000Hz instead of platform default of
250Hz.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[Apply same changes to 5.4]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Currently kmod-hwmon-* will not get into images unless kmod-hwmon-core is added
to DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-gpiofan
- kmod-hwmon-lm63
- kmod-hwmon-lm75
- kmod-hwmon-lm85
- kmod-hwmon-lm90
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, adjust line wrapping]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The previous workaround for the unsupported mkimage xz compression
leads to the TP-Link TL-WDR4900s simpleImage bootwrapper being gzip
compressed, which does not fit the kernel partition.
Removing the uImage gerneration works around this problem.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes some outstanding issues with the Kernel 5.4 build:
* Adds missing support patch for the Enterasys WS-AP3710i
* Fixes incorrect NAND symbols
* Adds patch for broken image wrapping
Signed-off-by: David Bauer <mail@david-bauer.net>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Hardware
--------
SoC: NXP P1020 (2x e500 @ 800MHz)
RAM: 256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 1x Gigabit Ethernet (Atheros AR8033)
LED: System (green/red) - Radio{0,1} (green)
LAN (connected to PHY)
- GE blue
- FE green
Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.
Installation
------------
1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in
the root directory of a TFTP server and serve it at
192.168.200.200/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Set the bootcmd so the AP can boot OpenWrt by executing
$ setenv boot_openwrt "setenv bootargs;
cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
$ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
By adding the vendor to the Makefile device definition node name,
one can derive the standard compatible used in SUPPORTED_DEVICES
instead of having to specify it manually.
Despite, this moves the naming scheme closer to what is used for
other targets (ath79, ramips).
Build-tested on all subtargets.
Run-tested on TP-Link TL-WDR4900 v1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment.
Previously, the MAC addrss was read for the ethernet from the "config"
partition. However, the content of this partition is dependent on the
firmware which was previously installed on the device.
Switch the MAC address source to the U-Boot partition, where the MAC
address is always present at a fixed partition. The partition was
previously already used for the WiFi MAC-addresses.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.
Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.
This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.
(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)
Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WLAN0 and the unused LED are currently swapped. Fix this, so the LED
behavior matches the other OCEDo devices.
Signed-off-by: David Bauer <mail@david-bauer.net>
After commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage")
XZ compression of zImage was enabled. This change exposed a problem with
the HiveAP-330 images, which was fixed by foregoing the compression on
the kernel altogether with commit 98089bb8ba
("mpc85xx: Use uncompressed kernel on the HiveAP-330").
This patch adds back the gzip compression of the kernel image by
utilizing the generic OpenWRT uImage method instead of relying on
the PowerPC bootwrapper script that did it previously.
Compile-tested: p1020/hiveap-330
Tested-by: Chris Blake <chrisrblake93@gmail.com> [run-tested]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[filled in even more text]
It seems that newer builds of OpenWRT have a gzip kernel
larger than 2MB~, which for some reason fails to boot on this board.
However, we have 8MB of kernel space and currently the uncompressed
kernel is 6.5MB~, so we have some space to grow until a better
solution is worked out.
Before:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2315724 Bytes = 2.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
ft_fixup_l2cache: FDT_ERR_NOTFOUND
After:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: POWERPC OpenWrt Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 6724584 Bytes = 6.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Loading Kernel Image ... OK
OK
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 cpl limit]
Lets bump kernel to 4.19 on targets which were run tested or got ACKed
so we've enough time to make it ready for next release:
armvirt/32 (runtested in qemu)
armvirt/64 (runtested in qemu)
ath79/generic (runtested on Carambola2)
gemini/generic (runtested on DIR-685, DNS-313, SQ201, SL93512R)
imx6/generic (runtested on Apalis)
ipq40xx/generic (runtested on nbg6617)
malta/be64 (runtested in qemu)
malta/be (runtested in qemu)
malta/le (runtested in qemu)
malta/le64 (runtested in qemu)
mpc85xx/generic (runtested on TL-WDR4900)
mpc85xx/p2020 (runtested on P2020RDB)
mvebu/cortexa53
mvebu/cortexa72
mvebu/cortexa10
octeon/generic (runtested on EdgeRouter Lite)
sunxi/cortexa53 (build tested only)
sunxi/cortexa7 (runtested on Lime2-K)
sunxi/cortexa8 (build tested only)
tegra/generic
x86/64 (runtested in qemu)
Acked-by: Zoltan HERPAI <wigyori@uid0.hu> [sunxi]
Tested-by: Linus Walleij <linus.walleij@linaro.org> [gemini]
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [mvebu, tegra]
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [octeon]
Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [mpc85xx/generic mpc85xx/p2020]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Converts the TP-Link WDR4900 v1 to use the simpleImage in the
hopes of prolonging the life of the device. While at it,
the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE
to 2684 KiB as a precaution since the stock u-boot is using a
fixed kernel size.
Note: Give the image some time, it will take much longer to
extract and boot.
[tested for 4.14/4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Both targets have their own idea of how to use ehci-fsl.
This patch reverts part of commit
68b8d3b079 ("kernel: usb: add FSL EHCI package") and moves
ehci-fsl back into kmod-usb2, while also making it hopefully
useable for the mpc85xx target.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The current mpc85xx build is failing because the
TL-WDR4900v1 kernel image no longer fits into the
partition. Extending the kernel is not possible
without updating u-boot's kernel loader commands.
This patch disables the WDR4900v1 until the kernel
image size issue is fixed so the buildbot can still
compile the Sophos RED 15w Rev.1 . Installing the
WDR4900v1 images would cause the routers to get
bricked.
For the discussion, please go to:
<https://github.com/openwrt/openwrt/pull/1773>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
