It's reported that current memory detection code occasionally detects
larger memory under some bootloaders.
Current memory detection code tests whether address space wraps around
on KSEG0, which is unreliable because it's cached.
Rewrite memory size detection to perform the same test on KSEG1 instead.
While at it, this patch also does the following two things:
1. use a fixed pattern instead of a random function pointer as the magic
value.
2. add an additional memory write and a second comparison as part of the
test to prevent possible smaller memory detection result due to
leftover values in memory.
Fixes: 6d91ddf517 ("ramips: mt7621: add support for memory detection")
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 2f024b7933)
[backport for OpenWrt 21.02 as it was reproducible with Kernel 5.4, see [1]]
[1]: https://forum.openwrt.org/t/113081
Tested-by: Dimitri Souza <dimitri.souza@gmail.com> [mt7621/archer-c6-v3]
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
The bit position mask was accidentally made too wide, overlapping with the LSB
from the byte position mask. This caused ECC calculation to fail for odd bytes
Signed-off-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 918d4ab41e)
The $INODE64 symbol variants are not present, since the base system
always uses 64-bit file offsets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 53ebacacf9)
Added patch for MacOS without 32 bit inodes support
(__DARWIN_ONLY_64_BIT_INO_T is true)
This patch based on discussion https://github.com/archmac/bootstrap/issues/4
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
(cherry-picked from commit 8fedc17d01)
For some reason, the generated configure script fails to properly set up
the internal preprocessor command variable, causing the host OS check for
Darwin to fail after the last update.
Explicitly setting CPP fixes this issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 48e209e5c5)
This fixes the following security problem:
The command-line argument parser in tcpdump before 4.99.0 has a buffer
overflow in tcpdump.c:read_infile(). To trigger this vulnerability the
attacker needs to create a 4GB file on the local filesystem and to
specify the file name as the value of the -F command-line argument of
tcpdump.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 8f5875c4e2)
14f2867b57 Fix failing nss/tst-nss-files-hosts-long with local resolver
d27d1e4d13 posix: Fix attribute access mode on getcwd [BZ #27476]
4b95183785 S390: Add PCI_MIO and SIE HWCAPs
6090cf1330 elf: Replace nsid with args.nsid [BZ #27609]
9edf29fd72 s390: Use long branches across object boundaries (jgh instead of jh)
94c91ce231 support: Add xpthread_kill
f9592d65f2 nptl: Do not set signal mask on second setjmp return [BZ #28607]
1cc490adca powerpc64[le]: Fix CFI and LR save address for asm syscalls [BZ #28532]
c76a0ba878 gconv: Do not emit spurious NUL character in ISO-2022-JP-3 (bug 28524)
c493f6a0e4 powerpc64[le]: Allocate extra stack frame on syscall.S
55b99e9ed0 powerpc: Fix unrecognized instruction errors with recent GCC
a51b76b71e x86: use default cache size if it cannot be determined [BZ #28784]
f10e992e8d socket: Add the __sockaddr_un_set function
4653cd9e36 CVE-2022-23219: Buffer overflow in sunrpc clnt_create for "unix" (bug 22542)
dae9a8e7f6 sunrpc: Test case for clnt_create "unix" buffer overflow (bug 22542)
4f4452721d <shlib-compat.h>: Support compat_symbol_reference for _ISOMAC
0f70b829f8 CVE-2022-23218: Buffer overflow in sunrpc svcunix_create (bug 28768)
5cab4e3f3a powerpc: Fix unrecognized instruction errors with recent binutils
ac148bdd88 elf: Fix glibc-hwcaps priorities with cache flags mismatches [BZ #27046]
e081bafcb1 support: Add helpers to create paths longer than PATH_MAX
e41e5b97e3 realpath: Set errno to ENAMETOOLONG for result larger than PATH_MAX [BZ #28770]
f63cb3cf72 tst-realpath-toolong: Fix hurd build
46a70c49ba support: Add xclone
bcdde07537 getcwd: Set errno to ERANGE for size == 1 (CVE-2021-3999)
41980af2d7 realpath: Avoid overwriting preexisting error (CVE-2021-3998)
48d9161e02 Linux: Detect user namespace support in io/tst-getcwd-smallbuff
06ce5fbd6d support: Fix xclone build failures on ia64 and hppa
d251ad533e aarch64: align stack in clone [BZ #27939]
3d52239b30 x86: Fix __wcsncmp_avx2 in strcmp-avx2.S [BZ# 28755]
86c153d092 NEWS: Add a bug fix entry for BZ #28755
6b7b6c7514 test-strnlen.c: Initialize wchar_t string with wmemset [BZ #27655]
a744a0a3fe test-strnlen.c: Check that strnlen won't go beyond the maximum length
f0a2b67147 x86: Set Prefer_No_VZEROUPPER and add Prefer_AVX2_STRCMP
9cee072f8f x86-64: Add ifunc-avx2.h functions with 256-bit EVEX
06d1aed51b x86-64: Add strcpy family functions with 256-bit EVEX
1697e739ef x86-64: Add memmove family functions with 256-bit EVEX
47bf9f38bb x86-64: Add memset family functions with 256-bit EVEX
15bae38c8b x86-64: Add memcmp family functions with 256-bit EVEX
0598a25cbe x86-64: Add AVX optimized string/memory functions for RTM
82f1ba9af7 x86: Add string/memory function tests in RTM region
763cea698b x86-64: Use ZMM16-ZMM31 in AVX512 memset family functions
d49105cc7a x86-64: Use ZMM16-ZMM31 in AVX512 memmove family functions
31dd3e3cb3 x86-64: Fix ifdef indentation in strlen-evex.S
902af2f5ee NEWS: Add a bug fix entry for BZ #27457
e09c377806 x86: Optimize memchr-avx2.S
453ed0a0f2 x86: Fix overflow bug with wmemchr-sse2 and wmemchr-avx2 [BZ #27974]
b72b89705e x86: Optimize strlen-avx2.S
355afae940 x86: Optimize memchr-evex.S
3dea108f60 x86-64: Fix an unknown vector operation in memchr-evex.S
5697e2dda8 x86-64: Move strlen.S to multiarch/strlen-vec.S
3ac5a7fe8b x86-64: Add wcslen optimize for sse4.1
cef3bffade x86: Fix overflow bug in wcsnlen-sse4_1 and wcsnlen-avx2 [BZ #27974]
8a3a0177c7 x86: Optimize strlen-evex.S
2b00ee820a String: Add overflow tests for strnlen, memchr, and strncat [BZ #27974]
25941de34e NEWS: Add a bug fix entry for BZ #27974
3e2a15c666 x86-64: Require BMI2 for __strlen_evex and __strnlen_evex
5cb6edb6cd x86: Copy IBT and SHSTK usable only if CET is enabled
0a5f5e2dc1 x86: Check RTM_ALWAYS_ABORT for RTM [BZ #28033]
54fdfa2b33 x86: Black list more Intel CPUs for TSX [BZ #27398]
1b8f2456b9 x86: Use CHECK_FEATURE_PRESENT to check HLE [BZ #27398]
260360e89b x86: Remove wcsnlen-sse4_1 from wcslen ifunc-impl-list [BZ #28064]
1956ad4930 x86-64: Test strlen and wcslen with 0 in the RSI register [BZ #28064]
78d25827ae Linux: Simplify __opensock and fix race condition [BZ #28353]
9495d729f6 hurd if_index: Explicitly use AF_INET for if index discovery
55446dd8a2 socket: Do not use AF_NETLINK in __opensock
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes some recent security problems in hostapd.
See here for details: https://w1.fi/security/2022-1
* CVE-2022-23303
* CVE-2022-23304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
x509v3 SAN extension is required to generate a certificate compatible with
chromium-based web browsers (version >58)
It can be disabled via unsetting CONFIG_WOLFSSL_ALT_NAMES
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
(cherry picked from commit dfd695f4b9)
This fixes the following security problems:
* Zeroize several intermediate variables used to calculate the expected
value when verifying a MAC or AEAD tag. This hardens the library in
case the value leaks through a memory disclosure vulnerability. For
example, a memory disclosure vulnerability could have allowed a
man-in-the-middle to inject fake ciphertext into a DTLS connection.
* Fix a double-free that happened after mbedtls_ssl_set_session() or
mbedtls_ssl_get_session() failed with MBEDTLS_ERR_SSL_ALLOC_FAILED
(out of memory). After that, calling mbedtls_ssl_session_free()
and mbedtls_ssl_free() would cause an internal session buffer to
be free()'d twice. CVE-2021-44732
The sizes of the ipk changed on MIPS 24Kc like this:
182454 libmbedtls12_2.16.11-2_mips_24kc.ipk
182742 libmbedtls12_2.16.12-1_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 57f38e2c82)
Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between
5.4.171 and 5.4.179.
The following 3 patches do not apply any more:
* target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch
This was already integrated in kernel v5.4-rc1, it was never needed.
* target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch
* target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch
I think these were done to fix the problem which was really fixed in
commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio
hogs") from v5.4.175
target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch
Move fwnode_device_is_available to the same position as in kernel 5.10.
target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch
Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts:
ls1028a-qds: move rtc node to the correct i2c bus")
Compile-tested: lantiq/xrx200, bcm27xx/bcm2710
Run-tested: lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/200 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 4x GPIO-LEDs (3x wifi, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8031 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
This device support is based on the partially working stub from commit
53c474abbd ("ath79: add new OF only target for QCA MIPS silicon").
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 1699c1dc7f)
This commit fixes commit "2999f810ff: build,IB: include kmods only in
local builds" which cause the local packages/ folder only to be added
for local builds but no longer for ImageBuilder created by the Buildbot.
The commits intention was to use remote kmods repositories rather than
storing them locally. Accidentally the entire handling of the local
`packages/` was removed.
Re-add the folder and include a README describing what it can be used
for.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 15e55a2190)
Fixes: #5068
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
945d0d7 utils: fix C style in header file
2cfc26f inittab: detect active console from kernel if no console= specified
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ffeb37047e)
This adds conflicts between variants of libustream pacakge.
They provide the same file and thus it should not be possible to install
them side by side.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
(cherry picked from commit 219e17a350)
All buttons of the FritzBox 7360 family are active-low, not active-high.
Corrent the GPIO flag. This fixes release triggers upon push of a button.
Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3154537864)
Apply the same fix that was previously done for the Archer C7v5 to the
A7v5 as well to make the web UI accept our images again.
This is a backport of firmware-utils
commit 84dbf8ee49f522d3a4528763c9473cf3dd7c8c52.
Tested-by: Luflosi <luflosi@luflosi.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds.
Investigation shows that the board failed to adapt the ethernet pll values as shown here:
[ 5.284359] ag71xx 19000000.eth: failed to read pll-handle property
added custom prints in code and triggering a link switch:
[ 62.821446] Atheros AG71xx: fast reset
[ 62.826442] Atheros AG71xx: update pll 2
[ 62.830494] Atheros AG71xx: no pll regmap!
Comparison with another very similar board (rb922 - QCA955x) showed a missing
reference clock frequency in dts, which seems to cause a pll init issue.
Unfortunately, no errors are printed when this occurs.
Adding the frequency property fixes the pll init as it can be parsed now
by the ethernet driver.
[ 55.861407] Atheros AG71xx: fast reset
[ 55.866403] Atheros AG71xx: update pll 2
[ 55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 2a00054618)
Adds support for GPON SFP modules based on the Realtek RTL8672 and
RTL9601C chips, including but not limited to:
* V-SOL V2801F
* C-Data FD511GX-RM0
* OPTON GP801R
* BAUDCOM BD-1234-SFM
* CPGOS03-0490 v2.0
* Ubiquiti U-Fiber Instant
* EXOT EGS1
Signed-off-by: Vladimir Markovets <abam_a@yahoo.com>
(cherry picked from commit f032601ed7)
This allows LEDs to be triggered by custom pattern and not just
predefined ones.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
(cherry picked from commit 507911f477)
The name of the module is 'uleds', not 'leds-uleds'.
Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com>
[improve commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3e9318f3c0)
The allows userspace LEDs to be created and controlled. This can be useful
for testing triggers and can also be used to implement virtual LEDs.
Signed-off-by: Keith T. Garner <kgarner@kgarner.com>
[squash fixup commit and improve option wording]
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 6a37286c2a)
The patch
PCI: aardvark: Don't touch PCIe registers if no card connected
was applied into Linux stable version 5.4.163.
Remove it from patches-5.4.
(It applied even though it was applied already, resulting in repeated
code.)
Fixes: 14940aee45 ("kernel: bump 5.4 to 5.4.163")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
This is a bugfix release. Changelog:
*) Avoid loading of a dynamic engine twice.
*) Fixed building on Debian with kfreebsd kernels
*) Prioritise DANE TLSA issuer certs over peer certs
*) Fixed random API for MacOS prior to 10.12
Patches were refreshed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit def9565be6)
Right now it includes bcm4908 variant only that is required by BCM4908
family devices with U-Boot.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit f18288e267)
This is a requirement for backporting DT files defining such LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 85ad48c957)
BCM4908 devices with U-Boot use pkgtb firmware format. It's based on
U-Boot's FIT: DTB with configurations, images & embedded data.
This format contains bootfs, rootfs and optionally a first stage U-Boot
loader. Contained images need to be extracted & flashed.
Broadcom used two sets of firmwares: main & backup. It uses UBI volumes
"metadata1" & "metadata2" for storing U-Boot env variables with info
about flashed images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 5f05795aa7)
It's very useful flag for handling various formats in sysupgrade. This
commit comes from the 1.34.0 release.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
fdt* utils are needed by targets that use U-Boot FIT images for
sysupgrade. It includes all recent BCM4908 SoC routers as Broadcom
switched from CFE to U-Boot.
fdtget is required for extracting images (bootfs & rootfs) from
Broadcom's ITB. Extracted images can be then flashed to UBI volumes.
sysupgrade is core functionality so it needs dtc as part of base code
base.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This results in setting format specific data (format info, extract
commands) in a single function. It should help maintaining sysupgrade
code.
This change has been tested on Asus GT-AC5300 and Netgear R8000P.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 30b168b9b8)
