The default strength is not enough to provide stable connection
under 3.3v LDO voltage.
Fixes: 32d5921b8b ("rockchip: add Orange Pi R1 Plus LTS support")
Fixes: #13117Fixes: #13759
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Commit 25746a3fa2da ("drm/i915: fix up merge with usb-next branch") was
internally applied to the 5.15 patch but wasn0t applied to the backport
for kernel 6.1. Apply the same treatement also there to fix compilation
warning.
Fixes: a14240d384 ("kernel: backport list_count_nodes()")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add downstream DT property to setup the PHY LEDs of the MaxLinear
GPY211 PHY in such way that the VDD of the LED is driven by the SoC
pin rather than the GND (which is the default).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The backported patch is broken, since kernel 6.1 has not
'include/linux/firmware' directory yet.
Fix the include to the correct path.
Fixes: #14115
Fixes: 52c365f055 ("kernel: backport v6.6 nvmem changes")
Signed-off-by: Andrey VOLKOV <andrey@volkov.fr>
[ improve commit description and title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The MAC address increment has been replaced by the new "mac-base"
NVMEM fixed layout. This old implementation can be removed now.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Add the 'tmon' packages. This is as a tool to help visualize,
tune, and test the complex thermal subsystem.
We get a compile warning for the tool that the printf format does not
fit. This commit contains a patch that fixes this warning. This patch
has also been sent upstream to the Linux kernel [1].
Links:
[1] https://lore.kernel.org/all/20231204141335.2798194-1-fe@dev.tdt.de/
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Fixes issues with RTL8156 2.5G USB adapters
- # ethtool eth1
Settings for eth1:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 2500Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
MDI-X: Unknown
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
- #
- r8152: break the loop when the budget is exhausted
- r8152: Block future register access if register access fails
- r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
- r8152: add vendor/device ID pair for D-Link DUB-E250
- r8152: try to use a normal budget
- r8152: set bp in bulk
- r8152: adjust generic_ocp_write function
- r8152: fix the autosuspend doesn't work
- r8152: Add __GFP_NOWARN to big allocations
- r8152: reduce the control transfer of rtl8152_get_version()
- r8152: remove rtl_vendor_mode function
- r8152: avoid to change cfg for all devices
- r8152: add USB device driver for config selection
- r8152: use napi_gro_frags
- cdc_ether: no need to blacklist any r8152 devices
- cdc_ether: add u-blox 0x1313 composition
Build system: x86_64
Build-tested: bcm2711, rockchip, x86/64
Run-tested: bcm2711/RPi4B, rockchip/nanopi r2s, x86/64
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Openwrt supports hundreds of devices. These newly added LED colors
and functions can help developers better describe LED indicators.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In addition to binary and ASCII-formatted MAC addresses, add support
for processing hexadecimal encoded MAC addresses from NVMEM.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Another Qualcomm-based USB-connected modem, offering endpoints
0 : rndis_host (link to voip subsystem listening on 169.254.5.100)
1 : rndis_host (?)
2 : option (?)
3 : option (at)
4 : option (at)
5 : option (?)
6 : GobiNet (qmi)
7 : ?
Add support for this modem in rndis_host, option and qmi_wwan driver
which allows the modem to be used with ModemManager.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This mtdsplit parser driver parses firmware partition on Internet
Initiative Japan Inc. (IIJ) SEIL series devices.
Structure of header:
0x0 - 0x7 : Identifier (hex)
0x8 - 0x57: Copyright (ascii)
0x58 - 0x5b: Data CRC (hex)
0x5c - 0x5f: Image Format Version (hex)
0x60 - 0x63: Image Major Version (hex)
0x64 - 0x67: Image Minor Version (hex)
0x68 - 0x87: Image Release Version (ascii)
0x88 - 0x8b: Xor value for Data? (hex)
0x8c - 0x8f: Data Length (hex)
Properties:
- compatible : "iij,seil-firmware"
- iij,seil-id : ID of SEIL firmware for the device (8 bytes)
- examples:
- SA-W2 : <0x5345494c 0x32303135> ("SEIL2015")
- SEIL/X1 : <0x5345494c 0x2F582020> ("SEIL/X ")
- iij,bootdev-name: boot device name assigned to the partition
(optional)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:
./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]
This was originally applied via 55643e469c, but was unintentionally
reverted in 483503603c.
Fixes: 483503603c ("generic: 5.15: rework pending patch")
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
This is a backport of the patch to support the Altima AMI101L
PHY which is merged for the v6.7 kernel. This PHY is used in the
IXP4xx-based USRobotics USR8200.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a backport of the patch for byte addressed IO to the
Epson RTC7301 driver. This is used by the IXP4xx-based
USRobotics USR8200.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This backports patches
leds: turris-omnia: convert to use dev_groups
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Do not use SMBUS calls
leds: turris-omnia: Make set_brightness() more efficient
leds: turris-omnia: Support HW controlled mode via private trigger
leds: turris-omnia: Add support for enabling/disabling HW gamma correction
leds: turris-omnia: Fix brightness setting and trigger activating
into backport-5.15.
The above patches replace:
leds: turris-omnia: support HW controlled mode via private trigger
leds: turris-omnia: initialize multi-intensity to full
leds: turris-omnia: change max brightness from 255 to 1
from mvebu/patches-5.15.
Signed-off-by: Marek Behún <kabel@kernel.org>
This backports patches
leds: turris-omnia: Use sysfs_emit() instead of sprintf()
leds: turris-omnia: Drop unnecessary mutex locking
leds: turris-omnia: Do not use SMBUS calls
leds: turris-omnia: Make set_brightness() more efficient
leds: turris-omnia: Support HW controlled mode via private trigger
leds: turris-omnia: Add support for enabling/disabling HW gamma correction
leds: turris-omnia: Fix brightness setting and trigger activating
into backport-6.1.
The above patches replace:
leds: turris-omnia: support HW controlled mode via private trigger
leds: turris-omnia: initialize multi-intensity to full
leds: turris-omnia: change max brightness from 255 to 1
from mvebu/patches-6.1.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Disable new ksym globally as OpenWrt does not have any targets that
use A520 cores.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
Backport qca8k fixes for big endian system (to make them working again)
and a patch fixing MDIO conflicts if other PHY are connected and mgmt
eth is used to control the switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch enabling assisted learning for qca8k to fix roaming issue
between BSS and BSS on the same L2 broadcast domain.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Symbol rtl8366_enable_vlan and rtl8366_reset_vlan are also present in
the DSA driver upstream and conflicts as they are EXPORTED.
Rename them to rtl8366_smi_enable_vlan and rtl8366_smi_reset_vlan to fix
the conflict. While at it also make them static and drop the
EXPORT_SYMBOL_GPL as they are not actually used by any other driver and
exporting them is useless.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport pending patch for multi CPU port support on QCA8K. 6.1 already
supports all the requiredt code to change a DSA master port so only this
patch fixing the driver is required.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport various QCA8K fixes patch merged upstream. Refresh any changed
patches due to backports.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
UARTs not used as boot console are currently broken on some MediaTek
targets due to register access depending on the bus clock being enabled.
Add patch to make sure this dependency is always met.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Since 5.15 doesnt have phylink_get_caps I had to modify the backport to
use the old mv88e6393x_phylink_validate instead.
I had to fixup one more instance of port_max_speed_mode as well that is not
present in 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 5356462ce5.
Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.
It seemed that mtd OF_POPULATED hack resolved probing issues but
apparently not all of them. We got reports about reading MAC using NVMEM
not working and USB controllers not working.
Ref: #10232Fixes: #13412
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This symbol was added by commit 2e6f34faa7e0 ("Input: Add IBM Operation
Panel driver") to v6.1. It depends on I2C so it's available to limited
amount of targets. It needs to be specified thought to allow kernel
configuration.
For bcm53xx this fixes:
IBM Operation Panel driver (INPUT_IBM_PANEL) [N/m/?] (NEW)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
These suboptions (PLATFORM, FSL_MC and MLX5_VFIO_PCI)
may be prompted for when VFIO is enabled, regardless of
architecture.
These are not related to the main vfio use case
(passthrough of PCIe devices)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch was wrongly tagged as being part of Linux 6.0 even though it
was only committed with Linux 6.2 and hence needs to be backported for
Linux 6.1.
Fixes: fa79baf4a6 ("generic: copy backport, hack, pending patch and config from 5.15 to 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25: 00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
Backport patch adding support for LED PHY directly in PHY ops struct.
Add new PHYLIB_LEDS config and refresh patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 79af0593a3.
A hack adjusting fw_devlink value was added to workaround issue with
probing device drivers caused by of_platform_populate(). With upstream
mtd commit (the one adding OF_POPULATED) backported there is no need for
that hack anymore.
Ref: 3eebb91317 ("kernel: backport proper fix for mtd preventing devices probing")
Ref: #10232
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This change makes it possible to use the GPIO_OPEN_DRAIN /
GPIO_OPEN_SOURCE Flags when exporting GPIOs via dts.
We need to emulate the open-source or open-drain functionalities for the
initial value, because the used functions (gpiod_direction_output_raw)
do not take this into account.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Rename two patches which were only accepted in Linux 6.2, but were
marked as if they were accepted in Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
