Takimata reported on the OpenWrt forum in thread [0], that his
MyBook Live Duo wasn't booting OpenWrt 21.02 after upgrading
from the previous OpenWrt 19.07.
The last logged entries on his console
|[ 0.531599] sata1-regulator GPIO handle specifies active low - ignored
|[ 0.538391] sata0-regulator GPIO handle specifies active low - ignored
|[ 0.759791] ata2: SATA link down (SStatus 0 SControl 300)
|[ 0.765251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
|[ 5.909555] ata1.00: qc timeout (cmd 0xec)
|[ 5.913656] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
|[ 6.231757] ata1: SATA link down (SStatus 0 SControl 300)
This extract clearly showed that the HDD on which OpenWrt is installed,
simply disappeared after the SATA power regulators had been initialized.
The reason why this worked with OpenWrt 19.07 was because the kernel
config symbol CONFIG_REGULATOR=y was not set in the target's config-4.14.
(This shows that the MBL Single does differ from the DUO in that
it does not have programmable power regulators for the HDDs.)
[0] <https://forum.openwrt.org/t/21-02-0-and-snapshot-fail-to-boot-on-my-book-live-duo/106585>
Reported-by: Takimata (forum)
Tested-by: Takimata (forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default
symbols for the ath79/mikrotik target.
MikroTik devices hold some of their user-configurable settings in the
soft_config partition, which is typically sized 4 KiB, of the SPI NOR
flash memory. Previously, in the ar71xx target, it was possible to use
64 KiB erase sectors but also smaller 4 KiB ones when needed. This is
no longer the case in ath79 with newer kernels so, to be able to write
to these 4 KiB small partitions without erasing 60 KiB around, the
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults.
However, this ended up making sysupgrade images which were built with
64 KiB size blocks not to keep settings (e.g., the files under
/etc/config/) over the flashing process.
Using 4 KiB erase sector size on the sysupgrade images (by setting
BLOCKSIZE = 4k) allows keeping settings over a flashing process, but
renders the process terribly slow, possibly causing a user to
mistakenly force a manual device reboot while the process is still on-
going. Instead, ditching the 4 KiB erase sectors for the default
64 KiB erase size provides normal SPI write speed and sysupgrade times,
at the expense of not being able to modify the soft_config partition
(which is rarely a required thing).
An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have
allowed to use different per-partition erase sector sizes. Due to
changes on recent kernels it now only works on a per-device basis.
Also, partial eraseblock write can be performed in ath79 with kernels
5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole
sector and restoring those blocks not meant to be modified. A kernel
bump had that patch broken for a long time, but got fixed in bf2870c.
Note: the settings in the soft_config partition can be reset to their
defaults by holding the reset button for 5 seconds (and less than 10
seconds) at device boot.
Fixes: FS#3492 (sysupgrade […] loses settings...)
Fixes: a66eee6336 (ath79: add mikrotik subtarget)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
isl.gforge.inria.fr has been dead since early this month [1]. Switch to
libisl.sourceforge.io for the time being.
[1] https://groups.google.com/g/isl-development/c/JGaMo2VUu_8
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Currently the tar.bz2 while ImageBuilder and SDK switched to tar.xz.
Unify it for faster compression since it will make use of
multi-threading.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This fixes passing a bogus non-null pointer to the ubus handler in case
the transition request is rejected.
Signed-off-by: David Bauer <mail@david-bauer.net>
AR9331 requires kmod-usb2-chipidea to use the USB ports. Include the
correct package so they can be used with the base image.
Signed-off-by: David Bauer <mail@david-bauer.net>
Both hostapd and netifd attempt to add a VLAN device to a bridge.
Depending on which one wins the race, bridge vlan settings might be incomplete,
or hostapd might run into an error and refuse to service the client.
Fix this by preventing hostapd from adding interfaces to the bridge and
instead rely entirely on netifd handling this properly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
c61a1d432b34 wireless: fix creating AP mode WDS station interfaces
f78bdec2ed5f wireless: fix handling vif attributes on reload with mode change
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Backport upstream SFP support for the Marvell 88E1510/2 PHY-s.
Globalscale MOCHAbin uses this PHY for the hybrid
WAN port that has 1G SFP and 1G RJ45 with PoE PD
connected to it.
This allows the SFP port to be used on it as well as
parsing the SFP module details with ethtool.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Backport upstream support for 100Base-FX, 100Base-LX, 100Base-PX and
100Base-BX10 SFP modules.
This is a prerequisite for the Globalscale MOCHAbin hybrid 1G
SFP/Copper support backporting.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Refactor so that the outer function opens and closes the mei fd and
passes it around, just as with the main fd.
That also allows us to use the IOCTL macro in get_vector_status() and
clean up accordingly.
Switch to AUTORELEASE while at it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Add in a fix for 160Mhz dfs on 5.10 and higher.
Add support for 5.13 and 5.15 kernels.
Add of_get_mac_address support for 5.15 driver.
Signed-off-by: Andrew Robbins <andrew@robbinsa.me>
Removed upstreamed:
backport-5.4/070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
The nl80211 was out of sync with the version used in our backports. This
broke the configuration of the antenna gain.
Fixes: 2bfac61483 ("mac80211: backport support for BSS color changes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The video feed just got support for Wayland which allows OpenWrt devices
to run as a Kiosk (displaying browser content via a display).
The availability of these packages should be mentioned to users.
Signed-off-by: Paul Spooren <mail@aparcar.org>
They're preferred terminal descriptions for tmux, with additional support to
some special characters and italic fonts. More info can be found at:
https://github.com/tmux/tmux/wiki/FAQ
Fixes: FS#3404
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
When a ubus event handler denies a association with a non-zero return
value, the code jumps to preceeding code, creating an endless loop until
the event handler accepts the assc request.
Move the ubus handler further up the code to avoid creating such a loop.
Signed-off-by: David Bauer <mail@david-bauer.net>
Right now when I want to temporarily disable wg peer I need to delete
the entire peer section. This is not such a good solution because I
loose the previous configuration of the peer.
This patch adds `disabled` option to peer config which causes that
the config section is ignored.
Signed-off-by: Stepan Henek <stepan.henek@nic.cz>
[use $(AUTORELEASE)]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This introduces support for hardware flow offloading, which was added in
in nftables 0.9.9.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
This target has testing support for kernel 5.10 for four months now.
Time to switch the default.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Both should be supported since:
1. Adding NVMEM driver for NVRAM
2. Using NVRAM info for determining active firmware partition
Linksys EA9500 uses very similar design and works fine.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It's the default anyway and this just looks confusing, as if it wasn't.
Switch to AUTORELEASE while at it.
The binary size is unchanged.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This gates out anything that might introduce semantically frivolous jitter,
maximizing chance of identical object files.
The binary size shrinks by 8kb:
1244352 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
1236160 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
Signed-off-by: Andre Heider <a.heider@gmail.com>
"Alternate certification chains, as oppossed to requiring full chain
validataion. Certificate validation behavior is relaxed, similar to
openssl and browsers. Only the peer certificate must validate to a trusted
certificate. Without this, all certificates sent by a peer must be
used in the trust chain or the connection will be rejected."
This fixes e.g. uclient-fetch and curl connecting to servers using a Let's
Encrypt certificate which are cross-signed by the now expired
DST Root CA X3, see [0].
This is the recommended solution from upstream [1].
The binary size increases by ~12.3kb:
1236160 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
1248704 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
[0] https://github.com/openwrt/packages/issues/16674
[1] https://github.com/wolfSSL/wolfssl/issues/4443#issuecomment-934926793
Signed-off-by: Andre Heider <a.heider@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: David Bauer <mail@david-bauer.net>
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use kernel 5.10 by default
compile-tested: all devices from target (wth ALL_KMODS)
run-tested: Digilent Zybo Z7-20
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This fixes compilation of several wireless drivers that
require support for the old wireless extension to work.
One example is kmod-hermes.
The symbols are set to "y" on generic configuration.
But they were wrongly disabled on the target-specific
configuration.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Until now, this feature was switched on via the kernel configuration
option KERNEL_SECCOMP.
The follwing change a7f794cd2a now requires that
the package procd-seccomp must also enabled for buildinmg.
However, this is not the case we have no dependency and the imagebuilder
cannot build the image, because of the implicit package selection.
This change adds a new configuration option CONFIG_SECCOMP.
The new option has the same behaviour as the configuration
option CONFIG_SELINUX.
If the CONFIG_SECCOMP is selected then the package procd-seccomp and
KERNEL_SECCOMP is enabled for this build.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
