Commit Graph

1175 Commits

Author SHA1 Message Date
Imre Kaloz
211cac98d5 Belkin AC 1750 DB (F9K1115v2) support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43734
2014-12-17 08:27:38 +00:00
Felix Fietkau
8c6f1412b1 ar71xx: improve ethernet driver cache footprint by removing an unnecessary pointer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43588
2014-12-09 12:28:46 +00:00
John Crispin
3572657c5a ar71xx: dev-eth: replace mdelay calls
Similar to patch 2. Replace further mdelay calls.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 43540
2014-12-07 16:53:15 +00:00
John Crispin
59e7999a44 ag71xx: replace delay with sleep calls
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 43539
2014-12-07 16:53:09 +00:00
John Crispin
4caa8d50ad ag71xx: replace fixed PHY reset wait time in ar7240sw_setup
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 43538
2014-12-07 16:52:58 +00:00
Imre Kaloz
974f286261 add D-link DGL-5500 A1 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43401
2014-11-27 14:27:34 +00:00
John Crispin
47ab1cbf23 ar71xx: add support for TP-LINK CPE210/220/510/520
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 43385
2014-11-26 08:59:32 +00:00
Imre Kaloz
15f6f67d18 Netgear R6100 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43382
2014-11-26 08:28:22 +00:00
John Crispin
f210f3811a ar71xx: Added support for D-link DHP-1565 rev. A1
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>

SVN-Revision: 43307
2014-11-19 09:20:47 +00:00
John Crispin
6fafcba63b ar71xx: Fix the sys LEDs on the EasyLink M150 and mini
Sets the system LED on the EasyLink M150 and mini to lower-case "easylink"

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 43271
2014-11-14 16:58:29 +00:00
John Crispin
bc333d5399 ar71xx: add kernel support for the OpenMesh MR900v2
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43265
2014-11-14 16:54:58 +00:00
John Crispin
95544f33dd ar71xx: add kernel support for the OpenMesh MR900 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43258
2014-11-14 16:54:07 +00:00
John Crispin
2c72ffc154 ar71xx: add support for Netgear WNR2000v4
Signed-off-by: Michaël Burtin <mburtin@gmail.com>

SVN-Revision: 43173
2014-11-03 20:20:56 +00:00
Felix Fietkau
a1837135e0 ar71xx: add support for buffalo WZR-450HP2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43026
2014-10-22 11:02:18 +00:00
John Crispin
6e46fc8a38 wr1043nd-v2: Change .code of the wi-fi button to KEY_RFKILL
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.

Signed-off-by: Josef Gajdusek <atx@atx.name>

SVN-Revision: 42922
2014-10-14 19:01:21 +00:00
John Crispin
99c238ff15 ar71xx: Fix LED definitions for the DRAGINO2 board
This patch fixes LED definitions for the DRAGINO2 board.

1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 42897
2014-10-14 10:33:07 +00:00
John Crispin
e2c3c2280c ar71xx: fix reset button gpio for OM2P/OM2P-HS
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".

Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 42782
2014-10-06 04:51:51 +00:00
John Crispin
7dbbdfb61f ar71xx: add qihoo 360 c301 router support
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.

This patch adds its initial support.

v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 42552
2014-09-15 10:19:38 +00:00
Felix Fietkau
1961f8cdb7 ar71xx: ack completed tx descriptors only after the full frame has been completed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42457
2014-09-10 12:56:24 +00:00
Felix Fietkau
60b81acd60 ath79: dev-eth: Don't advertise 1gbit in link code word on ar9331
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable.  The existing code
however advertieses gigabit capability in the link status word.  If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link.  This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.

In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.

So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit.  This patch implements the
former solution.

Signed-off-by: Harald Welte <laforge@gnumonks.org>

SVN-Revision: 42432
2014-09-07 09:45:32 +00:00
Felix Fietkau
60eeadd0ba ar71xx: re-enable descriptor splitting on ar716x after the previous bugfixes (#13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42429
2014-09-06 17:51:48 +00:00
Felix Fietkau
2da2317fed ar71xx: fix off-by-one error in packet descriptor splitting (patch from #13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42428
2014-09-06 17:51:44 +00:00
Felix Fietkau
05dd36a980 ar71xx: on ar716x, split ethernet packets in 512 byte chunks instead of 256 (improves performance) (patch from #13072)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42427
2014-09-06 17:51:39 +00:00
Felix Fietkau
926f000b99 ar71xx: disable ethernet descriptor splitting for now, as it seems to cause tx hangs in some setups
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42333
2014-08-30 09:11:41 +00:00
Felix Fietkau
2c680151e4 ar71xx: split packets into multiple descriptors on ar716x
This improves performance when doing concurrent rx/tx on a single
ethernet MAC, e.g. when routing between VLANs.

Fixes #13072

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42328
2014-08-29 19:42:08 +00:00
John Crispin
67cf439237 ar71xx: use ETH_ALEN for consistency
Signed-off-by: Forest Crossman <cyrozap@gmail.com>

SVN-Revision: 42280
2014-08-25 06:35:58 +00:00
John Crispin
e5e1c03354 ar71xx: TL-WR1043N/ND v2: Fix MAC address of WMAC
This sets the MAC address of the WLAN interface to the "official" primary MAC
address (the one on the label under the devices, and the one used with the stock
firmware). The MAC address used so far (primary-1) isn't even used at all with
the stock firmware, which sets (primary) on LAN and WLAN and (primary+1) on the
WAN interface (like OpenWrt does with this patch).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 42193
2014-08-18 13:10:00 +00:00
John Crispin
2c67682192 ar71xx: Fix 2.4G WiFi LED of the OpenMesh MR600 board
The OpenMesh MR600(v1) can only enable the 2.4G WiFi PHY LED through the
mini-PCIe device. Not configuring the LED pin inside the platform data
makes it impossible to configure it through any standard OpenWrt tool.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 42184
2014-08-18 13:09:14 +00:00
Imre Kaloz
ecba34a3ee add support for the NC-LINK SMART-300
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 42130
2014-08-11 11:44:51 +00:00
Felix Fietkau
e41a0cafff ar71xx: add linux 3.14 support
Signed-off-by: Zhao, Gang <gang.zhao.42@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 42038
2014-08-07 12:40:53 +00:00
Felix Fietkau
b855faecc0 ar71xx: update Carambola2 platform data
Change list:
 * Remove button info on GPIO12, there is no button there.
 * Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.

Tested building for carambola2 target.

Signed-off-by: Mantas Pucka <mantas@8devices.com>

SVN-Revision: 41993
2014-08-04 14:46:52 +00:00
John Crispin
e7ec79821a ar71xx: oolite: the buttons are not active_low
this caused factory resets when reboot was pressed

Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41932
2014-08-01 11:19:34 +00:00
Imre Kaloz
dc628f2e08 add support for the archer c5
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 41814
2014-07-23 12:47:25 +00:00
John Crispin
a440524f85 ar71xx: Fix GL.iNet WLAN LED
LED script expects WLAN LED to be "gl-connect:red:wlan".

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41793
2014-07-21 19:26:46 +00:00
John Crispin
eae9b2541a ar71xx: split wndr4300 and wndr3700v4 into 2 seperate mips machines
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41788
2014-07-21 18:41:52 +00:00
John Crispin
f424994cbc ar71xx: add kernel support for the OpenMesh OM5P board
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 41769
2014-07-20 17:30:32 +00:00
Gabor Juhos
aff3127956 ar71xx: add kernel support for the EnGenius EAP300 v2 board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41658
2014-07-14 21:30:26 +00:00
Gabor Juhos
51c892053a ar71xx: add kernel support for the Tube2H board
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41649
2014-07-14 16:03:34 +00:00
Gabor Juhos
907bd5345e ar71xx: fix ALFA NETWORK's name
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41643
2014-07-14 11:10:00 +00:00
Gabor Juhos
0bec90b830 ar71xx: add kernel support for the EnGenius ESR900
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5714/
[juhosg:
  - drop nvram.c modifications,
  - create a separate kernel patch,
  - use ath79_setup_qca955x_eth_cfg helper,
  - merge esr900_{010,common}_setup functions,
  - statically init AR8327 pad configurations,
  - use pr_err instead of printk]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41640
2014-07-14 10:25:51 +00:00
Gabor Juhos
26b39cc580 ar71xx: use ath79_setup_qca955x_eth_cfg helper for QCA955x based boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41627
2014-07-13 19:44:00 +00:00
Gabor Juhos
16d45d5531 ar71xx: add kernel support for EnGenius ESR1750
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5840/
[juhosg:
  - fix coding style in mach-esr1750.c,
  - rename and refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41624
2014-07-13 19:43:57 +00:00
Gabor Juhos
ee3dfafaf1 ar71xx: add a helper function for setting up ETH_CFG register on QCA955x
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5839/
[juhosg: fix coding style]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41623
2014-07-13 19:43:56 +00:00
Gabor Juhos
a46c7d055c ar71xx: allow ath79_nvram_parse_mac_addr parsing mac with quotes
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
  - fix coding style,
  - check the first and the last character of the MAC string
    instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41622
2014-07-13 19:43:54 +00:00
Gabor Juhos
9801351c84 ar71xx: add kernel support for GL-Inet V1 boards/routers
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>

Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>

This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.

Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
  - remove user-space and image generation support, will be included
    from other patches,
  - fix coding style and drop superfluous comment in mach-gl-inet.c,
  - rename and refresh kernel patch,
  - adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 41618
2014-07-13 18:21:04 +00:00
John Crispin
9e26031a88 ar71xx: add support for TP-LINK TL-WA860RE v1
New router/repeater from TP-LINK

- CPU: Atheros AR9341-DL3A (AP123)
- Flash: 4MB
- Ram: 32MB

Similar to TL-WA850RE.

Changes: rename file after r41596

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 41598
2014-07-13 10:03:41 +00:00
John Crispin
42a37b2a89 ar71xx: added support for TL-WA830RE V2
Corrected patch ath79 insted of auth79. Sorry.

Signed-off-by: Fredrik Jonson <fredrik@famjonson.se>

SVN-Revision: 41596
2014-07-13 07:12:22 +00:00
John Crispin
3519322e62 ar71xx: Add support for MikroTik RouterBOARD SXT Lite
This patch adds support for the MikroTik RouterBOARD SXT Lite.

The new RB911L series is also supported as a result.

v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41450
2014-07-01 13:38:30 +00:00
John Crispin
23a9bfc655 ar71xx: r41348 is missing these files
sorry, the downside when applying patches with patch

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41350
2014-06-26 13:47:35 +00:00
John Crispin
680e0c09f3 ar71xx: WNDAP360 adding wifi LED support
I added WIFI LED support (so now AP blinks nicely), I removed WPS
button GPIO (as it doesn't exist) and changed GPIO for reset button.

Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>

SVN-Revision: 40976
2014-06-02 15:02:54 +00:00
John Crispin
05b73eb22f ar71xx: add kernel support for HiWiFi HC6361.
This board manufactured by HiWiFi has the following features.

 - Atheros 9331 SoC.
 - 16MB flash and 64MB RAM.
 - 4GB eMMC storage via SK6226 USB 2.0 controller.
 - 2 LAN and 1 WAN ethernet ports with LEDs on them.
 - 3 blue LEDs on the front panel.
 - 1 button labeled as "reset".
 - Powered by a USB cable.

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 40973
2014-06-02 14:56:24 +00:00
John Crispin
60ec05fdcb ar71xx: add support for dlink dir-615-e1
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.

Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>

SVN-Revision: 40969
2014-06-02 14:43:35 +00:00
John Crispin
c9f15772a1 ar71xx: add kernel support for the OpenMesh OM2P-HSv2
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 40961
2014-06-02 13:21:26 +00:00
John Crispin
ef5f37a08d ar71xx: add kernel support for the OpenMesh OM2Pv2 board
Signed-off-by: Marek Lindner <marek@open-mesh.com>
[sven@open-mesh.com: Rebased]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 40955
2014-06-02 13:20:52 +00:00
Felix Fietkau
83dc560621 ar71xx: fix typo in tl-wr710n mac setup (fixes #16469)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 40840
2014-05-24 08:01:33 +00:00
Hauke Mehrtens
f5e5477c81 kernel: modify mtd related patches for 3.14
The change is the same as ("kernel/generic: modify mtd related
patches"). Since these files are under files directory, not a files
directory of specific kernel version, better to also change them. So
it will avoid adding files to future specific files directory
(e.g. files-3.14) for this mtd related change.

Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>

SVN-Revision: 40732
2014-05-08 21:52:04 +00:00
Gabor Juhos
1374e5a721 ar71xx: rb91x: fix ethernet packet loss issues
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.

Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40509
2014-04-13 20:41:52 +00:00
Gabor Juhos
a5e398abad ar71xx: add kernel support for ZyXEL NBG 6716
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot

Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
  - rename and refresh kernel patch,
  - fix a few typos,
  - change button key codes,
  - use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40499
2014-04-13 08:29:05 +00:00
Gabor Juhos
4149ab5193 ar71xx: wndr4300: indicate WNDR3700v4 in the kernel support files
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40479
2014-04-12 19:58:23 +00:00
Gabor Juhos
7b85e2e527 ar71xx: wndr4300: enable 5V power for the USB port
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.

Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40478
2014-04-12 19:58:20 +00:00
Gabor Juhos
ed72141fd4 ar71xx: wndr4300: use KEY_RFKILL code for the Wireless button
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40477
2014-04-12 17:53:34 +00:00
Gabor Juhos
4fe71cedfe ar71xx: wndr4300: add LED for 2.4Ghz wifi interface
Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40475
2014-04-12 17:42:35 +00:00
Gabor Juhos
db123a8a21 ar71xx: wndr4300: select GPIO_OUT functionality for LED GPIOs
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40474
2014-04-12 17:42:34 +00:00
Gabor Juhos
9b7b57aeb4 ar71xx: wndr4300: change 'orange' to 'amber' in LED color names
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.

Based on the the WNDR3700v4 support patch from Ralph Perlich:
  http://patchwork.openwrt.org/patch/4763/

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40473
2014-04-12 17:42:33 +00:00
Felix Fietkau
7131a104f5 ar71xx: add support for the TP-LINK TL-WR841N/ND v9
Everything seems to be working fine. Potential issues:

* VLAN port IDs are reversed with regard to the numbers on the case.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 40400
2014-04-07 08:00:02 +00:00
Felix Fietkau
f80f0c7d22 ar71xx: add support for QCA953x SoC
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.

Features not yet supported:

* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 40399
2014-04-07 07:59:45 +00:00
Gabor Juhos
5256bbdc56 ar71xx: add kernel support for the Oolite v1 board
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
 - use a separate patch for kernel changes,
 - reorder Kconfig and Makefile entries,
 - change function and variable names to be lowercase only
   and fix misaligned tabs in mach-gs-oolite.c,
   ... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 40032
2014-03-27 06:36:46 +00:00
Gabor Juhos
47dfbb5bc6 ar71xx: rb95x: use correct SPI flash address
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.

Compile tested only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39891
2014-03-12 12:52:39 +00:00
Gabor Juhos
25e870eed6 ar71xx: ar934x_nfc: fix memory initialization bug
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type)  * array_size   should be used in memset.

Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39890
2014-03-12 12:52:36 +00:00
Gabor Juhos
da2f3c1448 ar71xx: rb91x: register GPIO LEDs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39704
2014-02-23 08:11:53 +00:00
Gabor Juhos
14d95026b2 ar71xx: rb91x: add SPI device for the serial shift register
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.

Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39703
2014-02-23 08:11:52 +00:00
Gabor Juhos
3d906ac6ac ar71xx: rb91x-nand: rewrite to use GPIO API
Rewrite tha rb91x-nand driver to use GPIO API to
modify the NAND control lines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39700
2014-02-23 07:19:32 +00:00
Gabor Juhos
8fea668cb7 ar71xx: rb91x: register a gpio-latch platform device
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39699
2014-02-22 18:05:32 +00:00
Gabor Juhos
ab08c40487 ar71xx: add a generic GPIO latch driver
It will be used for the Mikrotik boards.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39697
2014-02-22 18:05:29 +00:00
Gabor Juhos
4e0309630b ar71xx: rb91x: fix pll_1000 value for eth0 to avoid packet loss
When the RB91x device uses a GbE link the connection
suffers from packet loss:

  root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 20 -q
  PING 192.168.1.254 (192.168.1.254): 65507 data bytes

  --- 192.168.1.254 ping statistics ---
  20 packets transmitted, 9 packets received, 55% packet loss
  round-trip min/avg/max = 4.570/4.815/4.999 ms

Using a different PLL value fixes the issue.

  root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 100 -q
  PING 192.168.1.254 (192.168.1.254): 65507 data bytes

  --- 192.168.1.254 ping statistics ---
  100 packets transmitted, 100 packets received, 0% packet loss
  round-trip min/avg/max = 4.449/5.413/13.870 ms

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39642
2014-02-20 17:07:56 +00:00
Gabor Juhos
d19b868b12 ar71xx: Add support for MikroTik RB951Ui-2HnD
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result.  I have cleaned up this patch.

When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.

This patch applies cleanly to SVN 39392.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
  - drop the 'rb951ui_wlan_init' function and rework the code to
    use the recently introduced rb95x_wlan_init function instead,
  - fix GPIO number of the port5 LED,
  - rename LEDs according to the standard LED naming conventions,
    and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39641
2014-02-20 17:07:51 +00:00
Gabor Juhos
db0e6e264d ar71xx: add kernel support for the TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4848/
[juhosg:
  - rename and refresh kernel patch,
  - merge the board setup code into mach-archer-c7.c and drop
    mach-tl-wdr49000-v2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39635
2014-02-19 12:15:32 +00:00
Gabor Juhos
3b8c51771d ar71xx: wpe72: set active_low flag for the reset button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39401
2014-01-26 14:55:34 +00:00
Gabor Juhos
b503dc026e ar71xx: wp543: set active_low flag for the buttons
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39400
2014-01-26 14:55:32 +00:00
Gabor Juhos
50f38063cd ar71xx: archer c7: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39395
2014-01-25 11:16:59 +00:00
Gabor Juhos
f85231257e ar71xx: fix bad RX sensitivity on newer TL-WDR4300 boards
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.

Setup the GPIOs of the external LNAs to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39392
2014-01-24 17:40:17 +00:00
Gabor Juhos
b629009eaa ar71xx: wp543: use KEY_RESET code for the sw4 button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39374
2014-01-23 12:23:08 +00:00
Gabor Juhos
0b599c51cc ar71xx: mynet-n750: define LEDs connected to the AR8327 switch
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4743/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39361
2014-01-21 17:17:42 +00:00
Gabor Juhos
506b40b628 ar71xx: tl-wr1043nd-v2: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39346
2014-01-20 10:23:06 +00:00
Gabor Juhos
c17cfab560 ar71xx: tl-wdr4300: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39345
2014-01-20 10:23:05 +00:00
Gabor Juhos
4c54635106 ar71xx: rb2011: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39341
2014-01-20 10:23:01 +00:00
Gabor Juhos
b4dc45e07d ar71xx: rb2011: fix eth5 LED
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39335
2014-01-20 10:22:49 +00:00
Gabor Juhos
30ebad2dee ar71xx: ag71xx: increase calculated max frame length value
The r39147 commit introduces a regression: at lease on some routers
with ar8216 switch large packets get lost if 802.1q tagged port is
used on the interface connected to the aforementioned switch.

The r39147 changes code in the way so interface is set to accept
packets no longer than max ethernet frame length for a given mtu.

Unfortunately ar8216 has a feature: it sends two additional bytes
as a packet header and those this header needs to be added to the
max frame length. Otherwise long enough packets get lost.

The problem only manuifests itself if interface is used in vlan
tagged mode. If interface is untagged then ar8216's header fits
into space used by 802.1q tag and not packets are lost.

Include two additional bytes in the max frame length calculation
to fix the issue.

This patch is tested and works with Trendnet TEW-632BRP.

Signed-off-by Nikolay Martynov <mar.kolya@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4656/
[juhosg:
  - simplify the patch to include the additional bytes of the
    switch header unconditionally,
  - change subject and update commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39219
2014-01-11 11:15:30 +00:00
Gabor Juhos
c977d49a29 ar71xx: my net n750: simplify LNA GPIO setup
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39217
2014-01-10 09:37:59 +00:00
Gabor Juhos
cc3beb9c76 ar71xx: my net n600: simplify LNA GPIO setup
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39216
2014-01-10 09:37:58 +00:00
Gabor Juhos
32aef686f7 ar71xx: Fix WD My Net N600 weak signal issue
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.

Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
  - remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
  - change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39214
2014-01-10 09:07:12 +00:00
Gabor Juhos
01727717f7 ar71xx: Fix WD My Net N750 weak signal issue
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.

Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".

Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39213
2014-01-10 09:07:11 +00:00
Gabor Juhos
05f8604e2e ar71xx: fix max frame length of the QCA955x SoCs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39161
2013-12-23 17:05:23 +00:00
Gabor Juhos
76f37c5d46 ar71xx: don't set builtin_switch flag for QCA9558
It makes no sense, the SoC has no built-in switch.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39160
2013-12-23 17:05:21 +00:00
Gabor Juhos
f2cd3399f7 ar71xx: allow to use large ethernet frames on AR934x SoCs
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.

Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39149
2013-12-20 11:41:23 +00:00
Gabor Juhos
2b220f3550 ar71xx: ag71xx: fix max frame length setup of the built-in switches
The currently used bitmask of the maximum frame length field
is wrong for both models. On AR724x/AR933x the largest frame
size is 2047 bytes, on the AR934x it is 16383 bytes.

Make the MTU setup code model specific, and use the correct
bitmask for both models. Also change the value to the maximum.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39148
2013-12-20 11:41:22 +00:00
Gabor Juhos
35d601f974 ar71xx: ag71xx: calculate max frame len register value from the MTU
Set the MAX_FRAME_LEN register to zero in ag71xx_hw_init()
and write the correct value into that from the ag71xx_open()
and ag71xx_fast_reset() functions.

Also recalculate the RX buffer size based on the actual
maximum frame length value to optimize memory allocation.
Additionaly, disallow to change the MTU value while the
interface it running.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39147
2013-12-20 11:41:20 +00:00
Gabor Juhos
9e7d77de2d ar71xx: ag71xx: add ag71xx_max_frame_len() helper
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39146
2013-12-20 11:41:18 +00:00
Gabor Juhos
2c4e3cf33a ar71xx: ag71xx: get max_frame_len and desc_pktlen_mask from platform data
This will allow to use SoC specific values for both.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39145
2013-12-20 11:41:17 +00:00
Gabor Juhos
9be1e508f9 ar71xx: ag71xx: store descriptor packet length mask in ag71xx struct
The currently used bitmask is not correct for all SoCs.
Introduce a new field in struct ag71xx and store the
bitmask in that. Use the current value for now, it will
be adjusted for each SoCs in further patches.

Aslo use the new field directly in the ag71xx_rx_packets
and ag71xx_hard_start_xmit() functions and remove the
ag71xx_desc_pktlen() helper.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39144
2013-12-20 11:41:16 +00:00