Add Generic subtarget definition. This is needed to keep consistent name
on every other target/subtarget and also to permit correct work of CI
workflows that expect a target/subtarget pattern.
Fixes: c16b2293fe ("ixp4xx: Resurrect IXP4xx support using device tree")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh ramips patches which got out of sync due to backported changes
of the MediaTek Ethernet driver.
Fixes: 6407ef8d2b ("kernel: backport upstream mediatek WED changes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Seems to be very similar to: https://openwrt.org/toh/tp-link/tl-wr902ac_v3
1 x usb
1 x eth
Powered by mini usb port.
Installation:
Can use TFTP method to install:
1. establish TFTP server at 192.168.0.66
2. provide tp_recover.bin file to the TFTP server
3. turn on router with reset button pressed
4. wait for led blinking, then release reset
Specification based on dmesg from already flashed device:
SoC Type: MediaTek MT7628AN ver:1 eco:2
CPU0 revision is: 00019655 (MIPS 24KEc)
Memory: 56028K/65536K available
CPU Clock: 580MHz
WiFi: MT7613BE
MAC addresses are all the same, except wifi5g which last part is decrement by one, ie.:
eth0 40:ed:00:cf:b9:9b
br-lan 40:ed:00:cf:b9:9b
phy0-ap0 40:ed:00:cf:b9:9b
phy1-ap0 40:ed:00:cf:b9:9a
Signed-off-by: Kamil Jońca <kjonca@onet.pl>
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Power (green, unmanaged)
- 1x Status (green, gpio)
- 1x 2.4G (green, hardware, mt76-phy0)
- 1x 2.4G (blue, gpio)
- 1x 5G (green, hardware, mt76-phy1)
- 1x 5G (blue, gpio)
- 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (default http://192.168.0.1/)
under "admin" account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following block:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>
5. Replace <some value> by a new superadmin password and add a line
which enabling superadmin login after. For example, the block after
the changes:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Add the 'tmon' packages. This is as a tool to help visualize,
tune, and test the complex thermal subsystem.
We get a compile warning for the tool that the printf format does not
fit. This commit contains a patch that fixes this warning. This patch
has also been sent upstream to the Linux kernel [1].
Links:
[1] https://lore.kernel.org/all/20231204141335.2798194-1-fe@dev.tdt.de/
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Acelink EW-7886CAX is an MT7986A (AKA Filogic 830) based access point.
It has 512 MiB of RAM, one 2.5 Gbps PoE (802.3at) Ethernet port and
on-SoC Wi-Fi. There is no printed MAC label (on my unit).
My unit came with Mediatek's firmware (based on OpenWrt 21.02)
installed. It was possible to simply upgrade using OpenWrt's sysupgrade
tool.
Another verified upgrade method is using U-Boot (requires UART). During
every boot there is "U-Boot Boot Menu". Selecting option "2. Upgrade
firmware" allows using U-Boot's tftp client to load and flash factory
image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The no-map property was incorrectly added, which kept the system-memory
available on the WS-AP3825 limited to 190MB. We are allowed to map the
page containing the CPU1 spin-table, we are just not allowed to write to
it.
Fixes: 57d7382cb1 ("mpc85xx: increase available RAM on Extreme Networks WS-AP3825i")
Signed-off-by: David Bauer <mail@david-bauer.net>
The system-mamory size was page-aligned prior to this commit, only
enabling to use 192MB of system memory of the 256 available.
This was due to the system-memory being manually shrinked to reserve the
upper 1MB for the second-core bootpage in the loader as well as the OS.
Fix this properly in the loader and in Linux using reserved-memory
definitions. This enables the device to use 250MB of system memory.
Signed-off-by: David Bauer <mail@david-bauer.net>
This device does not have wireless hardware, thus we don't need to ship
neither hostapd nor wireless drivers.
Signed-off-by: David Bauer <mail@david-bauer.net>
Append metadata in the special GL.iNet format.
This also enables use of the web-based U-Boot recovery.
U-Boot-Recovery
===============
The GL-MT2500 provides web-based U-Boot recovery. For this, hold the
reset button pressed for 5 seconds when attaching power to the device.
The LED will blink 5 times. Release the reset button.
The OpenWrt sysupgrade image can be installed by navigating to
http://192.168.1.1 in a web-browser.
The device does not work as a DHCP server, so manual IP configuration is
required.
Signed-off-by: David Bauer <mail@david-bauer.net>
Fixes issues with RTL8156 2.5G USB adapters
- # ethtool eth1
Settings for eth1:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 2500Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
MDI-X: Unknown
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
- #
- r8152: break the loop when the budget is exhausted
- r8152: Block future register access if register access fails
- r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
- r8152: add vendor/device ID pair for D-Link DUB-E250
- r8152: try to use a normal budget
- r8152: set bp in bulk
- r8152: adjust generic_ocp_write function
- r8152: fix the autosuspend doesn't work
- r8152: Add __GFP_NOWARN to big allocations
- r8152: reduce the control transfer of rtl8152_get_version()
- r8152: remove rtl_vendor_mode function
- r8152: avoid to change cfg for all devices
- r8152: add USB device driver for config selection
- r8152: use napi_gro_frags
- cdc_ether: no need to blacklist any r8152 devices
- cdc_ether: add u-blox 0x1313 composition
Build system: x86_64
Build-tested: bcm2711, rockchip, x86/64
Run-tested: bcm2711/RPi4B, rockchip/nanopi r2s, x86/64
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Change permissions of the bootcount init script from old mode 100644
to new mode 100755 to ensure its executability.
Fixes: 6cc14bf66a ("filogic: support Telenor branded ZyXEL EX5700")
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
- use color, function, function-enumerator properties.
- removes the label properties from LED nodes.
- add panic-indicator to the blue power/status LED.
Note: yes this brings the combined LAN/"switch" LED sort of back,
though I fully admit, it's a bit jank. Do you know a better option?
then please tell/make a PR!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The AC42U already had PHY Triggers in the DTS.
We are probably going to use them at some point.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Openwrt supports hundreds of devices. These newly added LED colors
and functions can help developers better describe LED indicators.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Presently, sysupgrade -n does *not* reset the overlayfs, retaining
unwanted filesystem contents. Adding PADDING=1 in front of
gen_image_generic.sh in image/Makefile ensures that the overlayfs is
recreated on firstboot.
Fixes: 080a769b4d ("qoriq: new target")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[add Fixes tag, rewrite commit subject and message to respect line
length]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Currently, sysupgrade without the -n option complains:
# sysupgrade -v tmp/openwrt-qoriq-generic-watchguard_firebox-m300-squashfs-sysupgrade.img.gz
upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
upgrade: Kernel switched to FIT uImage. Update U-Boot environment.
upgrade: Reading partition table from bootdisk...
upgrade: Extract boot sector from the image
upgrade: Reading partition table from image...
Image check failed.
So, add the missing 05_compat-version to /etc/board.d/ to allow
sysupgrade to save config without using -f.
Fixes: c4b499bc03 ("qoriq: use FIT uImage for Firebox M300 kernel")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[drop invalid copyright header, add SPDX license header, shorten commit
subject, add fixes tag]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Confiabits MT7981 is a Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 256 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 4x 10/100/1000 Mbps MT7531AE (3xLAN, 1xWAN)
- USB 2.0 port
- Buttons: 1 Reset button, 1 Mesh button.
- LEDs: 7x light-blue, 2x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- Power: 12 VDC, 1.5 A
MAC addresses in stock firmware and in this commit:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 00:0c:43:xx:xx:e1 | label+1 |
| LAN | 00:0c:43:xx:xx:e0 | label |
| WLAN 2g | 00:0c:43:xx:xx:e0 | label |
| WLAN 5g | 02:0c:43:xx:xx:e0 | |
+---------+-------------------+-----------+
The label MAC was found in 'Factory', 0x4
Installation:
The stock firmware is OpenWrt-based. If you can reach LuCI or SSH, just use the sysupgrade image
with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
GRUB_SERIAL is also used for the default serial on the target and not
only in grub. When no grub was build it was not available and the build
fails.
Rename GRUB_SERIAL to TARGET_SERIAL and make it always available on x86
and armsr targets.
Fixes: #14063
Fixes: b10768476f ("x86,armsr: interpolate GRUB_SERIAL into /etc/inittab")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Include XHCI USB drivers on the ZBT-Z8102AX router, the drivers are
required to be able to use the USB-connected M.2 slots for 4G/5G modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
All devices in the rockchip target have appended image-metadata. Enforce
the presence of this metadata to avoid flashing incomplete images.
This is the de-facto standard for almost all OpenWrt targets.
Signed-off-by: David Bauer <mail@david-bauer.net>
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the userspace adjustments which are no longer necessary.
While at that, move the mac-base to the common part, as it is again
exactly the same in both models.
And convert ART partition too - keep that one separate, as calibration
data length differs between the models.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Now that MAC address parser supports the hex format (without
delimiters), use the canonical MAC address stored in U-boot partition.
Get rid of the "mac-address-increment" binding.
While at that, convert ART partition too.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Addresses were swapped compared to the factory firmware. In addition to
that, one of them was shifted by -1. Fix that by setting wlan0 MAC
offset to 9, and wlan1 MAC offset to 2.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Enable all necessary drivers for the rk356x SoCs, including PHY,
SCMI, SPI etc. Also backport 2 upstream patches for sdhci fixes.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
