Commit Graph

655 Commits

Author SHA1 Message Date
Giammarco Marzano
0de6a3339f ipq40xx: Add ZTE MF289F
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).

Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.

There are currently two hardware revisions, which
differ on the 5Ghz radio:

AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz

Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
	(QCA9984): a/n/ac, 4x4 HW REV AT1
	(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot

Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
   in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
   GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
   (refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:

setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr

5. Please make backup of original partitions, if you think about revert to
   stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:

WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin

ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin

6. Login via ssh or serial and remove stock partitions
   (default IP 192.168.0.1):

 # this can return an error, if ubi was attached before
 # or rootfs part was erased before.
ubiattach -m 17

 # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
 # some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data

7. download and install image via sysupgrade -n
 (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
 to the device's /tmp directory)

 sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin

Sometimes it could print ubi attach error, but please ignore it
if process goes forward.

Flash Layout

NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"

SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"

Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
   for the device on a TFTP in the server's root.
   This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
   connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:

This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize

This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize

After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router

Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
INAGAKI Hiroshi
c34f071972 ipq40xx: add support for Sony NCP-HG100/Cellular
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.

Specification:

- SoC                   : Qualcomm IPQ4019
- RAM                   : DDR3 512 MiB (H5TC4G63EFR)
- Flash                 : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN                  : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet              : 10/100/1000 Mbps x2
  - Transceiver         : Qualcomm QCA8072
- WWAN                  : Telit LN940A9
- Z-Wave                : Silicon Labs ZM5101
- Bluetooth             : Qualcomm CSR8811
- Audio DAC             : Realtek ALC5629
- Audio Amp.            : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
  - RGB LED, Fan, Temp. sensors
- Touch Sensor          : Cypress CY8C4014LQI
- RGB LED driver        : TI LP55231 (2x)
- LEDs/Keys             : 11x, 6x
- UART                  : through-hole on PCB
  - J1: 3.3V, TX, RX, GND from tri-angle marking
  - 115200n8
- Power                 : 12 VDC, 2.5 A

Flash instruction using initramfs image:

1. Prepare TFTP server with the IP address 192.168.132.100 and place the
   initramfs image to TFTP directory with the name "C0A88401.img"

2. Boot NCP-HG100/Cellular and interrupt after the message
   "Hit any key to stop autoboot:  2"

3. Perform the following commands and set bootcmd to allow booting from
   eMMC

   setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
   saveenv

4. Perform the following command to load/boot the OpenWrt initramfs image

   tftpboot && bootm

5. On the initramfs image, perform sysupgrade with the sysupgrade image
   (if needed, backup eMMC partitions by dd command and download to
   other place before performing sysupgrade)

6. Wait for ~120 seconds to complete flashing

Known issues:

- There are no drivers for audio-related chips/functions in Linux Kernel
  and OpenWrt, they cannot be used.

- There is no driver for MINI54FDE Micro-Controller Unit, customized for
  this device by the firmware in the MCU. This chip controls the
  following functions, but they cannot be controlled in OpenWrt.

  - RGB LED
  - Fan
    this fan is controlled automatically by MCU by default, without
    driver
  - Thermal Sensors (2x)

- Currently, there is no driver or tool for CY8C4014LQI and cannot be
  controlled. It cannot be exited from "booting mode" and moved to "normal
  op mode" after booting. And also, the 4x buttons (mic mute, vol down,
  vol up, alexa trigger) connected to the IC cannot be controlled.

  - it can be exited from "booting mode" by installing and executing
    i2cset command:

    opkg update
    opkg install i2c-tools
    i2cset -y 1 0x14 0xf 1

- There is a connection issue on the control by uqmi for the WWAN module.
  But modemmanager can be used without any issues and the use of it is
  recommended.

- With the F2FS format, too many errors are reported on erasing eMMC
  partition "rootfs_data" while booting:

  [    1.360270] sdhci: Secure Digital Host Controller Interface driver
  [    1.363636] sdhci: Copyright(c) Pierre Ossman
  [    1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
  [    1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
  ...
  [    1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
  [    1.528325] mmc0: new HS200 MMC card at address 0001
  [    1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
  [    1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
  [    1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
  [    1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
  [    1.550323] Alternate GPT is invalid, using primary GPT.
  [    1.561669]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
  ...
  [    8.841400] mount_root: loading kmods from internal overlay
  [    8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
  [    8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
  [    9.240465] block: attempting to load /etc/config/fstab
  [    9.246722] block: unable to load configuration (fstab: Entry not found)
  [    9.246863] block: no usable configuration
  [    9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
  [    9.438915] urandom_read: 5 callbacks suppressed
  [    9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
  [   12.243332] mmc_erase: erase error -110, status 0x800
  [   12.246638] mmc0: cache flush error -110
  [   15.134585] mmc_erase: erase error -110, status 0x800
  [   15.135891] mmc_erase: group start error -110, status 0x0
  [   15.139850] mmc_erase: group start error -110, status 0x0
  ...(too many the same errors)...
  [   17.350811] mmc_erase: group start error -110, status 0x0
  [   17.356197] mmc_erase: group start error -110, status 0x0
  [   17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
  [   17.446910] mmc0: tuning execution failed: -5
  [   17.447111] mmc0: cache flush error -110
  [   18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
  [   18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
  [   18.198691] block: attempting to load /etc/config/fstab
  [   18.198972] block: unable to load configuration (fstab: Entry not found)
  [   18.203029] block: no usable configuration
  [   18.211371] mount_root: overlay filesystem has not been fully initialized yet
  [   18.214487] mount_root: switching to f2fs overlay

  So, this support uses ext4 format instead which has no errors.

Note:

- The primary uart is shared for debug console and Z-Wave chip. The
  function is switched by GPIO15 (Linux: 427).

  value:

    1: debug console
    0: Z-Wave

- NCP-HG100/Cellular has 2x os-image pairs in eMMC.

  - 0:HLOS, rootfs
  - 0:HLOS_1, rootfs_1

  In OpenWrt, the first image pair is used.

- "bootipq" command in U-Boot requires authentication with signed-image
  by default. To boot unsigned image of OpenWrt, use "mmc read" and
  "bootm" command instead.

- This support is for "Cellular" variant of NCP-HG100 and not tested on
  "WLAN" (non-cellular) variant.

- The board files of ipq-wifi may also be used in "WLAN" variant of
  NCP-HG100, but unconfirmed and add files as for "Cellular" variant.

- "NET" LED is used to indicate WWAN status in stock firmware.

- There is no MAC address information in the label on the case, use the
  address included in UUID in the label as "label-MAC" instead.

- The "CLOUD" LEDs are partially used for indication of system status in
  stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
  connected to the MCU.

MAC addresses:

LAN    : 5C:FF:35:**:**:ED (ART, 0x6    (hex))
WAN    : 5C:FF:35:**:**:EF (ART, 0x0    (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz  : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))

partition layout in eMMC (by fdisk, GPT):

Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910

Number  Start (sector)    End (sector)  Size Name
     1              34            1057  512K 0:SBL1
     2            1058            2081  512K 0:BOOTCONFIG
     3            2082            3105  512K 0:QSEE
     4            3106            4129  512K 0:QSEE_1
     5            4130            4641  256K 0:CDT
     6            4642            5153  256K 0:CDT_1
     7            5154            6177  512K 0:BOOTCONFIG1
     8            6178            6689  256K 0:APPSBLENV
     9            6690            8737 1024K 0:APPSBL
    10            8738           10785 1024K 0:APPSBL_1
    11           10786           11297  256K 0:ART
    12           11298           11809  256K 0:HSEE
    13           11810           28193 8192K 0:HLOS
    14           28194           44577 8192K 0:HLOS_1
    15           44578          306721  128M rootfs
    16          306722          568865  128M rootfs_1
    17          568866         3958065 1654M rootfs_data

[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Tomasz Maciej Nowak
0410c95f0b ipq40xx: base-files: properly close case
Fix this occurrence during boot:
/bin/board_detect: line 10: Unsupported: not found

Fixes: 80baffd2aa (" ipq40xx: add support for Pakedge WR-1")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-24 23:53:53 +02:00
Tomasz Maciej Nowak
04eb080290 ipq40xx: luma_wrtq-329acn: differentiate ethernet mac addresses
On OEM firmware both addresses for In and Out ports are different. Set
them as such also in OpenWrt.

Fixes: e24635710c (" ipq40xx: add support for Luma Home WRTQ-329ACN")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-24 23:53:53 +02:00
Kasparas Elzbutas
e562746263 ipq40xx: fix RUTX10 Wi-Fi woes
This partially reverts:
commit cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")

U-Boot on these devices mangles the device tree,
so nvmem-cell type calibration doesn't work.

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Signed-off-by: Kasparas Elzbutas <elzkas@gmail.com>
(added reference to commit, rewrote commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-09-24 23:53:53 +02:00
Andrew Sim
e2ffb61821
ipq40xx: fix power LED colour ID in Netgear WAC510 dts
led_power_green color ID in dts is mistakenly set to amber so
correct it by setting it to green

Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
2022-09-19 17:49:56 +02:00
Sungbo Eo
f0ea3df439 ipq40xx: disable devices with 3MiB kernel size
The image builds for Linksys EA6350 v3, EA8300, and MR8300 currently
fail on buildbots due to the KERNEL_SIZE, as stated in commit
17b7756b5a ("ipq40xx: 5.15: add testing kernel version"). Disable
these boards for now.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-09-18 21:33:50 +09:00
David Bauer
470ca65bda ipq40xx: add GL-AP1300 label-mac-device
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-11 16:24:11 +02:00
David Bauer
4d014a7bd6 ipq40xx: add WAN LED mapping for GL-AP1300
Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-11 15:53:49 +02:00
Gregory Detal
0be1b78856 ipq40xx: cellc_rtl30vw: fix imagebuilder generation
The image build process was modifying the generated IMAGE_KERNEL to
append rootfs information (crc). This caused:
 - sysupgrade & factory images to contain 2 times the root.squashfs
   information due to both modifying the same IMAGE_KERNEL.
 - the generated imagebuilder to contain an erroneous IMAGE_KERNEL that
   contained references to an unexisting root.squashfs (the one from
   previous cause). The RTL30VW wasn't therefore able to boot the
   generated images as they contained checksums from non existing rootfs.

This commit makes sure to use a temporary IMAGE_KERNEL to append the
rootfs information for both factory and sysupgrade images.

Fixes: #10511
Signed-off-by: Gregory Detal <gregory.detal@tessares.net>
2022-09-11 01:36:25 +02:00
John Audia
e8a62a1e60 kernel: bump 5.10 to 5.10.141
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-11 01:30:11 +02:00
David Bauer
c7c3509226 ipq40xx: add LTE packages for GL-AP1300
Add LTE packages required for operating the LTE modem optionally shipped
with the GL-AP1300.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-09 18:15:23 +02:00
Nick Hainke
5f458e64a9 ipq40xx: switch to 5.15 as default kernel
The testing kernel received now multiple months of testing. Set 5.15 as
default to give it a test with a broader audience.

Tested on:
- MikroTik SXTsq 5 AC
- FritzBox 4040/7530
- ZyXEL NBG6617

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-09-09 11:15:07 +02:00
Tomasz Maciej Nowak
47306d47ef ipq-wifi: add Pakedge WR-1 support
Calibration variants:
Pakedge-WR-1		ETSI, FCC and IC-2.4GHz
Pakedge-WR-1-ACMA	ACMA
Pakedge-WR-1-IC		IC-5GHz
Pakedge-WR-1-SRRC	SRRC

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-07 21:21:38 +02:00
Tomasz Maciej Nowak
80baffd2aa ipq40xx: add support for Pakedge WR-1
Pakedge WR-1 is a dual-band wireless router.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
      1. 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Rename initramfs image to:
   openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
   and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
   reset button. Hold the button, on the lates bootloader version, when
   Power and WiFi-5 LEDs will start blinking release it. For the older
   bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
   minute) the Power LED will start blinking, when stops, router is fully
   booted.
4. Connect to one of LAN ports and use SSH to open the shell at
   192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
   at some point, You want to go back to original firmware. The firmware
   provided by manufacturer on its site is encrypted and U-Boot accepts
   only decrypted factory images, so there's no way to restore original
   firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
   and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
   LED will start blinking, wait till it stops, then router is ready for
   configuration.

Additional information
U-Boot command line is password protected. Password is unknown.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-07 21:21:38 +02:00
David Bauer
e16a0e7e88 ipq40xx: add support for Extreme Networks WS-AP3915i
Hardware
--------
Qualcomm IPQ4029 WiSoC
2T2R 802.11 abgn
2T2R 802.11 nac
Macronix MX25L25635E SPI-NOR (32M)
512M DDR3 RAM
1x Gigabit LAN
1x Cisco RJ-45 Console port
Settings: 115200 8N1

Installation
------------

1. Attach to the Console port. Power up the device and press the s key
   to interrupt autoboot.

2. The default username / password to the bootloader is admin / new2day

3. Update the bootcommand to allow loading OpenWrt.

   $ setenv ramboot_openwrt "setenv serverip 192.168.1.66;
     setenv ipaddr 192.168.1.1; tftpboot 0x86000000 openwrt-3915.bin;
     bootm"
   $ setenv boot_openwrt "sf probe;
     sf read 0x88000000 0x280000 0xc00000; bootm 0x88000000"
   $ setenv bootcmd "run boot_openwrt"
   $ saveenv

4. Download the OpenWrt initramfs image. Serve it using a TFTP server as
   "openwrt-3915.bin" at 192.1681.66.

5. Download & boot the OpenWrt initramfs image on the access point.

   $ run ramboot_openwrt

6. Wait for OpenWrt to start.

7. Download and transfer the sysupgrade image to the device using e.g.
   SCP.

8. Install OpenWrt to the device using "sysupgrade"

   $ sysupgrade -n /path/to/openwrt.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-09-06 02:55:05 +02:00
Tomasz Maciej Nowak
4d8b42d8a7 ipq40xx: point to externally compiled dtbs in recipes
Adjusting dts will cause a rebuild of whole kernel as the buildroot
considers this a part of kernel source. It's a royal PITA when trying to
prepare support for new device, since this takes a lot of time on slower
systems. As it stands, buildroot itself, with own rule, also compiles
dtbs and the results are $(KDIR)/image-$(DEVICE_DTS).dtb. With setting
DEVICE_DTS_DIR to directory holding the device dts (similarly to some
other targets), buildroot doesn't consider changed dts as part of kernel
source and rebuilds only dtb. This really speeds up development. And
since the kernel built dts are no longer used, drop the paches adding
dtses to its build.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-09-06 02:50:04 +02:00
John Audia
f87175b303 kernel: bump 5.15 to 5.15.64
All patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-02 21:21:31 +02:00
Petr Štetiar
ca5c695a45 kernel: bump 5.15 to 5.15.62
Deleted following upstreamed patches:

 bcm27xx: 950-0006-drm-vc4-hdmi-Fix-HPD-GPIO-detection.patch
 bcm27xx: 950-0420-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch
 bcm27xx: 950-0425-drm-vc4-A-present-but-empty-dmas-disables-audio.patch
 bcm27xx: 950-0432-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch
 bcm27xx: 950-0433-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch
 bcm27xx: 950-0435-drm-vc4-Correct-pixel-order-for-DSI0.patch
 bcm27xx: 950-0436-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch
 bcm27xx: 950-0437-drm-vc4-Fix-dsi0-interrupt-support.patch
 bcm27xx: 950-0438-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch
 bcm27xx: 950-0443-drm-vc4-Fix-timings-for-interlaced-modes.patch
 bcm27xx: 950-0445-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch
 bcm27xx: 950-0475-drm-vc4-Reset-HDMI-MISC_CONTROL-register.patch
 bcm27xx: 950-0476-drm-vc4-Release-workaround-buffer-and-DMA-in-error-p.patch
 bcm27xx: 950-0477-drm-vc4-Correct-DSI-divider-calculations.patch
 bcm27xx: 950-0664-drm-vc4-dsi-Correct-max-divider-to-255-not-7.patch

 bcm53xx: 072-next-ARM_dts_BCM53015-add-mr26.patch

 mediatek: 920-linux-next-dts-mt7622-bpi-r64-fix-wps-button.patch

Manually rebased following patches:

 bcm27xx: 950-0004-drm-vc4-hdmi-Remove-the-DDC-probing-for-status-detec.patch
 bcm27xx: 950-0700-net-phy-lan87xx-Decrease-phy-polling-rate.patch
 bcm27xx: 950-0711-drm-vc4-Rename-bridge-to-out_bridge.patch
 bcm27xx: 950-0713-drm-vc4-Remove-splitting-the-bridge-chain-from-the-d.patch
 bcm27xx: 950-0715-drm-vc4-Convert-vc4_dsi-to-using-a-bridge-instead-of.patch
 bcm27xx: 950-0787-vc4-drm-vc4_plane-Keep-fractional-source-coords-insi.patch
 bcm27xx: 950-0914-mmc-block-Don-t-do-single-sector-reads-during-recove.patch

Runtime tested on turris-omnia and glinet-b1300.

Tested-by: John Audia <therealgraysky@proton.me> [bcm2711/RPi4B, mt7622/RT3200]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-08-23 10:37:04 +02:00
Petr Štetiar
d1163fd13f kernel: bump 5.10 to 5.10.137
Removed following upstreamed patch:

 * bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch

All other patches automagically rebased.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-08-23 10:37:04 +02:00
Hauke Mehrtens
ff06edd1f0 kernel: Activate CONFIG_GPIOLIB in generic configuration
All targets expect the malta target already activate the CONFIG_GPIOLIB
option. Move it to generic kernel configuration and also activate it for
malta.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-08-10 21:36:17 +02:00
Mark Mentovai
7f54bf6fe2
ipq40xx: add MikroTik wAP ac (RBwAPG-5HacD2HnD) support
The MikroTik wAP ac (RBwAPG-5HacD2HnD) is a dual-band dual-radio
802.11ac wireless access point with integrated antenna and two Ethernet
ports in a weatherproof enclosure. See
https://mikrotik.com/product/wap_ac for more information.

Important: this is the new ipq40xx-based wAP ac, not the older
ath79-based wAP ac (RBwAPG-5HacT2HnD), already supported in OpenWrt.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - CPU: 4x ARM Cortex A7
 - RAM: 128MB
 - Storage: 16MB NOR flash
 - Wireless
    - 2.4GHz: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
    - 5GHz: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075), 2x 1000/100/10Mb/s ports,
   one with 802.3af/at PoE in

Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.

Notes:
This preserves the MAC addresses of the physical Ethernet ports:
 - eth0 corresponds to the physical port labeled ETH1 and has the base
   MAC address. This port can be used to power the device.
 - eth1 corresponds to the physical port labeled ETH2 and has a MAC
   address one greater than the base.

MAC addresses are set from /lib/preinit/05_set_iface_mac_ipq40xx.sh
rather than /etc/board.d/02_network so that they are in effect for
preinit. This should likely be done for other MikroTik devices and
possibly other non-MikroTik devices as well.

As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.

Signed-off-by: Mark Mentovai <mark@mentovai.com>
2022-07-18 01:45:47 +02:00
Christian Lamparter
50c232d6f4 ipq-wifi: drop upstreamed board-2.bin
The BDFs for the:
	GL.iNet GL-B2200

were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-07-15 15:21:44 +02:00
Christian Lamparter
3b3eaf31cb ipq40xx: R619AC: replace space with - separator in variant string
Kalle:
"I see that variant has a space in it, does that work it correctly? My
original idea was that spaces would not be allowed, but didn't realise
to add a check for that."

Is this an easy change? Because the original author (Tim Davis) noted:
"You may substitute the & and space with something else saner if they
prove to be problematic."

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-07-15 15:21:44 +02:00
Thibaut VARÈNE
bb929a0f9c ipq40xx: mikrotik: make RouterBoot partition writeable
Linux MTD requires the parent partition be writable for a child
partition to be allowed write permission.
In order for soft_config to be writeable (and modifiable via sysfs),
the parent RouterBoot partition must be writeable

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2022-06-29 12:34:49 +02:00
Tomasz Maciej Nowak
539e60539a generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]
This is now built-in, enable so it won't propagate on target configs.

Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-24 17:10:24 +02:00
Matthew Hagan
811538ab22 ipq40xx: add support for Meraki MR74
The Meraki MR74 is part of the "Insect" series. This device is
essentially an outdoor variant of the MR33 with identical hardware, but
requiring a config@3 DTS option to be set to allow booting with the
stock u-boot.

The install procedure is replicated from the MR33, with the exception
being that the MR74 sysupgrade image must be used.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2022-06-19 12:31:02 +02:00
Christian Lamparter
ac2166b135 kernel: move Toshiba-TC58NVG0S3H patch to ipq40xx redux
Linux' upstream MTD-Maintainer Miquèl Raynal noted:
|Reverting seems the safest option here, not knowing how many devices
|have these damaged/counterfeit chips. If it is just a couple and only on
|Fritzboxes, as suggested in the Github issue this patch could be
|carried through OpenWrt and that would seem more future proof IMHO.

This patch follows up with the first patch. It actually
moves the patches out of target/linux/generic/pending into
the ipq40xx's patch heap and adds a little note what happend.

For more information, discussions or reports about bad TC58NVG0S3Hs,
please visit the OpenWrt's Github Issue #9962:
<https://github.com/openwrt/openwrt/issues/9962>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-19 12:31:02 +02:00
Rui Salvaterra
fbf6992f2b kernel: bump 5.15 to 5.15.45
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-06-06 19:20:28 +02:00
John Audia
f800f8d6fc kernel: bump 5.10 to 5.10.120
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800, x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-06-06 19:20:02 +02:00
Peter Adkins
b4184c666c ipq40xx: add support for Linksys WHW01 v1
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].

Specification
-------------

SOC:             Qualcomm IPQ4018
WiFi 1:          Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2:          Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth:       Qualcomm CSR8811 (A12U)
Ethernet:        Qualcomm QCA8072 (2-port)
SPI Flash 1:     Mactronix MX25L1605D (2MB)
SPI Flash 2:     Winbond W25M02GV (256MB)
DRAM:            Nanya NT5CC128M16IP-DI (256MB)
LED Controller:  NXP PCA963x (I2C)
Buttons:         Single reset button (GPIO).

Notes
-----

There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.

The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.

Serial console
--------------

A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).

(<-- Top of PCB / Device)

  J2
  [o o o o o o]
       |   | |
       |   |  `-- GND
       |    `---- TX
       `--------- RX

Installation instructions
-------------------------

1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.

Revert to "factory"
-------------------

1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.

Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-05 21:19:32 +02:00
David Bauer
b21b98627d ipq40xx: add Aruba AP-365 specific BDF
Aruba deploys a BDF in the root filesystem, however this matches the one
used for the DK04 reference board.

The board-specific BDFs are built into the kernel. The AP-365 shows
sinificant degraded performance with increased range when used with the
reference BDF.

Replace the BDF with the one extracted from Arubas kernel.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-06-02 16:50:12 +02:00
John Thomson
602b5f6c60 ipq40xx: cut ath10k board file for mikrotik subtarget
Avoid shipping ath10k board file in Mikrotik initram images

Most will only ever need to use these initram images once—to initially
load OpenWrt, but fix these images for more consistent Wi-Fi performance
between the initram and installed squashfs images.

OpenWrt BUILDBOT config ignores -cut packages in the initram images build.
This results in BUILDBOT initram images including the linux-firmware
qca4019 board-2.bin, and (initram image booted) Mikrotik devices loading
a generic BDF, rather than the intended BDF data loaded
from NOR as an api 1 board_file.

buildbot snapshot booted as initram image:
cat /etc/openwrt_version
r19679-810eac8c7f
dmesg | grep ath10k | grep -E board\|BDF
[    9.794556] ath10k_ahb a000000.wifi: Loading BDF type 0
[    9.807192] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16
crc32 11892f9b
[   12.457105] ath10k_ahb a800000.wifi: Loading BDF type 0
[   12.464945] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17
crc32 11892f9b

CC: Robert Marko <robimarko@gmail.com>
Fixes: 5eee67a72f ("ipq40xx: mikrotik: dont include ath10k-board-qca4019 by default")

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-05-27 14:15:09 +02:00
Robert Marko
5eee67a72f ipq40xx: mikrotik: dont include ath10k-board-qca4019 by default
Since MikroTik subtarget now uses dynamic BDF loading its crucial that it
doesnt include the board-2.bin at all which is provided by the
ath10k-board-qca4019 package.

So to resolve this dont include the ath10k-board-qca4019 package on the
MikroTik subtarget.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-05-19 11:07:02 +02:00
Robert Marko
ab141a6e2c ipq-wifi: remove packaged BDF-s for MikroTik devices
Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly,
there is noneed to include package and ship them like we do now.

This also resolves the performance issues that happen as MikroTik
changes the boards and ships them under the same revision but they
actually ship with and require a different BDF.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-05-19 11:07:02 +02:00
Robert Marko
4d4462cc2a ipq40xx: mikrotik: provide BDF-s on demand
Since we now can pass the API 1 BDF-s aka board.bin to the ath10k
driver per radio lets use that to provide the BDF-s for MikroTik devices.

This also resolves the performance issues that happen as MikroTik changes
the boards and ships them under the same revision but they actually ship
with and require a different BDF.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-05-19 11:07:02 +02:00
John Audia
6cdf974a3d kernel: bump 5.15 to 5.15.39
Removed upstreamed:
  backport-5.15/850-v5.17-0001-PCI-pci-bridge-emul-Add-description-for-class_revisi.patch
  backport-5.15/850-v5.17-0002-PCI-pci-bridge-emul-Add-definitions-for-missing-capa.patch
  backport-5.15/850-v5.17-0003-PCI-aardvark-Add-support-for-DEVCAP2-DEVCTL2-LNKCAP2.patch
  backport-5.15/850-v5.17-0004-PCI-aardvark-Clear-all-MSIs-at-setup.patch
  backport-5.15/850-v5.17-0005-PCI-aardvark-Comment-actions-in-driver-remove-method.patch
  backport-5.15/850-v5.17-0006-PCI-aardvark-Disable-bus-mastering-when-unbinding-dr.patch
  backport-5.15/850-v5.17-0007-PCI-aardvark-Mask-all-interrupts-when-unbinding-driv.patch
  backport-5.15/850-v5.17-0008-PCI-aardvark-Fix-memory-leak-in-driver-unbind.patch
  backport-5.15/850-v5.17-0009-PCI-aardvark-Assert-PERST-when-unbinding-driver.patch
  backport-5.15/850-v5.17-0010-PCI-aardvark-Disable-link-training-when-unbinding-dr.patch
  backport-5.15/850-v5.17-0011-PCI-aardvark-Disable-common-PHY-when-unbinding-drive.patch
  pending-5.15/850-0001-PCI-aardvark-Replace-custom-PCIE_CORE_INT_-macros-wi.patch
  pending-5.15/850-0004-PCI-aardvark-Rewrite-IRQ-code-to-chained-IRQ-handler.patch
  pending-5.15/850-0005-PCI-aardvark-Check-return-value-of-generic_handle_do.patch
  pending-5.15/850-0006-PCI-aardvark-Make-MSI-irq_chip-structures-static-dri.patch
  pending-5.15/850-0007-PCI-aardvark-Make-msi_domain_info-structure-a-static.patch
  pending-5.15/850-0008-PCI-aardvark-Use-dev_fwnode-instead-of-of_node_to_fw.patch
  pending-5.15/850-0009-PCI-aardvark-Refactor-unmasking-summary-MSI-interrup.patch
  pending-5.15/850-0010-PCI-aardvark-Add-support-for-masking-MSI-interrupts.patch
  pending-5.15/850-0011-PCI-aardvark-Fix-setting-MSI-address.patc
  pending-5.15/850-0012-PCI-aardvark-Enable-MSI-X-support.patch
  pending-5.15/850-0013-PCI-aardvark-Add-support-for-ERR-interrupt-on-emulat.patch
  pending-5.15/850-0015-PCI-aardvark-Optimize-writing-PCI_EXP_RTCTL_PMEIE-an.patch
  pending-5.15/850-0016-PCI-aardvark-Add-support-for-PME-interrupts.patch
  pending-5.15/850-0017-PCI-aardvark-Fix-support-for-PME-requester-on-emulat.patch
  pending-5.15/850-0018-PCI-aardvark-Use-separate-INTA-interrupt-for-emulate.patch
  pending-5.15/850-0019-PCI-aardvark-Remove-irq_mask_ack-callback-for-INTx-i.patch
  pending-5.15/850-0020-PCI-aardvark-Don-t-mask-irq-when-mapping.patch
  pending-5.15/850-0021-PCI-aardvark-Drop-__maybe_unused-from-advk_pcie_disa.patch
  pending-5.15/850-0022-PCI-aardvark-Update-comment-about-link-going-down-af.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-05-16 20:26:38 +02:00
John Audia
b754b0c721 kernel: bump 5.10 to 5.10.115
Removed upstreamed:
  backport-5.10/850-v5.17-0004-PCI-aardvark-Clear-all-MSIs-at-setup.patch
  pending-5.10/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-05-16 20:26:38 +02:00
Andreas Böhler
f167f4a9a4 IPQ4019: AVM FRITZ!Box 7530: Remove NAND ECC restrictions from DTS
Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in
contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded
ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the
kernel NAND detection routines to correclty set up the ECC parameters.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-05-15 16:35:00 +02:00
Pawel Dembicki
af425e4221 ipq40xx: revert Cell-C RTL30VW to legacy caldata extraction
This partially reverts
commit cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data").

After switching to nvmem RTL30VW, wifi was broken:

[   19.118319] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   19.118377] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   19.130285] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   19.159092] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin
[   19.238764] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[   19.238847] ath10k_ahb a000000.wifi: failed to fetch board file: -12
[   19.247362] ath10k_ahb a000000.wifi: could not probe fw (-12)
[   20.190797] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000
[   20.190853] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[   20.202893] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
[   20.231357] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin
[   20.317318] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0
[   20.317399] ath10k_ahb a800000.wifi: failed to fetch board file: -12
[   20.326098] ath10k_ahb a800000.wifi: could not probe fw (-12)

Bootloader mangles in NAND partitions and removes precal@X nodes in
working system:

root@OpenWrt:~# echo $(cat /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/label)
0:ART
root@OpenWrt:~# ls /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/
label  name   reg

Revert to legacy method fixed the problem.

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-05-15 16:32:25 +02:00
Christian Lamparter
91fa4826b9 ipq-wifi: drop upstreamed board-2.bin
The BDFs for the:
	Aruba AP-303
	ASUS RT-AC42U
	AVM FRITZ!Repeater 1200
	Buffalo WTR-M2133HP
	Cell C RTL30VW
	D-Link DAP-2610
	EnGenius EAP2200
	EnGenius EMD1
	EnGenius EMR3500
	EnGenius EMR5000
	EZVIZ CS-W3-WD1200G EUP
	Google Wifi
	Linksys MR8300 V1.0
	Luma WRTQ-329ACN
	MobiPromo CM520-79F
	NEC Platforms WG2600HP3
	Plasma Cloud PA1200 (updated version)
	Plasma Cloud PA2200
	ZTE MF286D

were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.

Furthermore the BDFs for the:
	8devices Habanero
	OpenMesh A62
	OpenMesh A42
	AVM FRITZ!Box 4040

have been updated.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-05-14 11:08:45 +02:00
Christian Lamparter
834c9b3f05 ipq40xx: Lyra: update RGB LED-Controller node for 5.10+
Add the reg and color property to each channel node. This
update is to accommodate the multicolor framework.

Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>

Note:

There is only a single extremely bright RGB-LED.
The RGB-color channels (i.e.: blue-0, blue-1 and blue-2)
are running in parallel to increase the current delivery
beyond what a single PWM-output on the LED controller
could do.

BugLink: https://github.com/openwrt/openwrt/issues/9851
Reported-By: Thomas Bøge <thomas@boegenielsen.dk>
Tested-By: Thomas Bøge <thomas@boegenielsen.dk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-05-14 11:08:45 +02:00
Rui Salvaterra
c3569a70c6 kernel: bump 5.15 to 5.15.36
Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-05-09 20:49:50 +01:00
Sungbo Eo
cb1dc49c18 ipq40xx: consolidate ar40xx driver files
Commit f4fb63d2ab ("ipq40xx: 5.10: move AR40xx to MDIO drivers") moved
the ar40xx driver files to kernel version specific directories to place
them in different subdirectory in kernel tree. But now kernel 5.4 is
gone and there is no reason to keep them separate. Move them back to
common files/ directory.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-05-05 09:19:00 +09:00
Nick Hainke
1526ccebd4 ipq40xx: 5.15: fix ar40xx driver
Also apply commit ab7e53e5cc ("ipq40xx: 5.10: fix ar40xx driver") to
5.15 driver.

The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code, these mdelays were existing, but in
the ar41xx.c they are gone.

Fixes: 87318eb179 ("ipq40xx: 5:15: copy config and patch from 5.10")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-05-05 09:19:00 +09:00
Sungbo Eo
daee22c7c0 ipq40xx: 5.15: refresh subtarget config
Update config with `make kernel_oldconfig CONFIG_TARGET=subtarget`.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-05-01 13:40:13 +09:00
Robert Marko
376834a743 ipq40xx: 5.15: refresh config
Refresh 5.15 kernel config for IPQ40xx due to large number of generic
config changes.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-05-01 13:40:13 +09:00
Robert Marko
2114b22ef3 ipq40xx: 5.15: drop upstreamed sleep clock patch
Patch that corrects sleep clock frequency has already been backported
to 5.15 stable so remove the duplicate patch.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-05-01 13:40:13 +09:00
Ansuel Smith
17b7756b5a ipq40xx: 5.15: add testing kernel version
Add 5.15 kernel as a testing kernel version in the Makefile.

Linksys EA6350v3/EA8300/MR8300 will not build with buildbot settings and
should be disabled when the target is switched, unless the image size is
reduced again.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
[add comment for increased kernel size]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-05-01 13:40:13 +09:00
Ansuel Smith
7517955eac ipq40xx: 5.15: refresh kernel patches
Refresh kernel patches.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
2022-05-01 13:40:13 +09:00
Ansuel Smith
7c692f685b ipq40xx: refresh ess driver and phy with new api
Kernel 5.15 have some new api for ethtool and phy.
Add ifdef to fix compilation error.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
2022-05-01 13:40:13 +09:00
Ansuel Smith
7a72fcc1c5 ipq40xx: fix wrong nand definition for wpj419
Fix wrong nand definition for wpj419 that differ from the upstream
node name.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-05-01 13:40:13 +09:00
Ansuel Smith
07ddbb9961 ipq40xx: 5:15: refresh config
Refresh config for kernel 5.15 using make kernel_menuconfig

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-05-01 13:40:13 +09:00
Ansuel Smith
29e177e4ee ipq40xx: 5:15: refresh patches
- Drop upstream patch
- Refresh dts patch

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-05-01 13:40:13 +09:00
Ansuel Smith
87318eb179 ipq40xx: 5:15: copy config and patch from 5.10
Copy config and patch from 5.10 to 5.15

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2022-05-01 13:40:13 +09:00
Nick Hainke
ab7e53e5cc ipq40xx: 5.10: fix ar40xx driver
This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-1101108651

The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.

Tested on:
- Fritz!Box 4040
- Fritz!Box 7530
- Mikrotik SXTsq 5AC
- ZyXEL NBG6617

- [0] https://git.codelinaro.org/clo/qsdk/oss/lklm/qca-ssdk/-/blob/NHSS.QSDK.11.4/src/init/ssdk_init.c#L2072

Suggested-by: Serhii Serhieiev <adron@mstnt.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-04-29 00:27:25 +02:00
John Audia
b92ec82235 kernel: bump 5.10 to 5.10.110
Removed upstreamed:
  generic/backport-5.10/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch
  generic/pending-5.10/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch
  ipq40xx/patches-5.10/105-ipq40xx-fix-sleep-clock.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Compile-/run-tested: ath79/generic (Archer C7 v2).

Signed-off-by: John Audia <graysky@archlinux.us>
2022-04-09 19:31:46 +02:00
Ray Wang
3204906569 ipq40xx: add RT-AC2200 alternative name to RT-AC42U/RT-ACRH17
RT-AC2200 is the same device with a different name. The OEM firmwares have the same MD5.

Signed-off-by: Ray Wang <raywang777@foxmail.com>
2022-04-09 19:31:46 +02:00
Petr Štetiar
39d28b84f1 Revert "ipq40xx: stop chromium sub-target builds on the buildbots"
This reverts commit 35d2bbc29b as we
believe we found that it is indeed an openssl issue, where openssl is
trying to use getrandom(2), but fails because this particular builder
has an ancient kernel without that syscall. We didn't get to the bottom
of why openssl doesn't fall back to something like /dev/random.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-04-01 07:41:01 +02:00
John Audia
c41da167d2 kernel: bump 5.10 to 5.10.109
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-03-30 18:33:38 +02:00
Christian Lamparter
35d2bbc29b ipq40xx: stop chromium sub-target builds on the buildbots
the buildbots are having troubles with the image.
They seem to get "Killed" at the last step of the KERNEL rule:

|/cros-vbutil -k zImage.itb.vboot -c "root=PARTUUID=%U/PARTNROFF=1" -o zImage.itb.vboot.new
|make[4]: *** [Makefile:18: zImage.itb.vboot] Killed

Since the Google Wifi (Gale) is currently the only target in
this sub-target. So this means that subtarget has to be disabled
from the time being to not be picked up by the builders.

For people wanting to checkout out OpenWrt on the Google Wifi:
please compile it locally.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-27 15:39:27 +02:00
Christian Lamparter
026fda10a5 ipq40xx: WAC510: device-tree overhauling
removes usb-port remains as neither the WAC510 nor the WAC505
come with a USB port. Update the LED properties to phase out
labels and introduce generic node-names as well as adding
the color, function and function-enumerator properties.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-26 02:02:44 +01:00
张 鹏
bdc786e82c ipq40xx: update E2600AC c1/c2 board
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.

Signed-off-by: 张 鹏 <sd20@qxwlan.com>
2022-03-25 18:14:13 +01:00
Andre Heider
cb6f4be137 ipq40xx: add support for FRITZ!Box 7520
This model, also know as "1&1 HomeServer", shares the same features as 7530.

The vendor firmware has artificial software limitations: only 2 of the 4
LAN-Ports are GBit, and the USB-Host is only v2.0.

With OpenWrt, USB is already working at v3.0.

Signed-off-by: Andre Heider <a.heider@gmail.com>
(updated commit message to reflect current state)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-25 18:14:13 +01:00
Brian Norris
f1c041e34f ipq40xx: Add subtarget for Google WiFi (Gale)
Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet
ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port.
In its stock configuration, it runs a Chromium OS-based system, but you
wouldn't know it, since you can only manage it via a "cloud" +
mobile-app system.

The "v2" label is coded into the bootloader, which prefers the
"google,gale-v2" compatible string. I believe "v1" must have been
pre-release hardware.

Note: this is *not* the Google Nest WiFi, released in 2019.

I include "factory.bin" support, where we generate a GPT-based disk
image with 2 partitions -- a kernel partition (using the custom "Chrome
OS kernel" GUID type) and a root filesystem partition. See below for
flashing instructions.

Sysupgrade is supported via recent emmc_do_upgrade() helper.

This is a subtarget because it enables different features
(FEATURES=boot-part rootfs-part) whose configurations don't make sense
in the "generic" target, and because it builds in a few USB drivers,
which are necessary for installation (installation is performed by
booting from USB storage, and so these drivers cannot be built as
modules, since we need to load modules from USB storage).

Flashing instructions
=====================

Documented here:
https://openwrt.org/inbox/toh/google/google_wifi

Note this requires booting from USB storage.

Features
========

I've tested:

 * Ethernet, both WAN and LAN ports
 * eMMC
 * USB-C (hub, power-delivery, peripherals)
 * LED0 (R/G/B)
 * WiFi (limited testing)
 * SPI flash
 * Serial console: once in developer mode, console can be accessed via
   the USB-C port with SuzyQable, or other similar "Closed Case
   Debugging" tools:
     https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable
 * Sysupgrade

Not tested:

 * TPM

Known not working:

 * Reboot: this requires some additional TrustZone / SCM
   configuration to disable Qualcomm's SDI. I have a proposal upstream,
   and based on IRC chats, this might be acceptable with additional DT
   logic:
     [RFC PATCH] firmware: qcom_scm: disable SDI at boot
     https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/
 * SMP: enabling secondary CPUs doesn't currently work using the stock
   bootloader, as the qcom_scm driver assumes newer features than this
   TrustZone firmware has. I posted notes here:
     [RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
     https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
 * There's a single external button, and a few useful internal GPIO
   switches. I haven't hooked them up.

The first two are fixed with subsequent commits.

Additional notes
================

Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which
the manufacturer image uses.

Note: the manufacturer bootloader knows how to patch in calibration data
via the wifi{0,1} aliases in the DTB, so while these properties aren't
present in the DTS, they are available at runtime:

  # ls -l
/sys/firmware/devicetree/base/soc/wifi@a*/qcom,ath10k-pre-calibration-data
  -r--r--r--    1 root     root         12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a000000/qcom,ath10k-pre-calibration-data
  -r--r--r--    1 root     root         12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a800000/qcom,ath10k-pre-calibration-data

Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(updated 901 - x1pro moved in the process)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-25 18:14:13 +01:00
Brian Norris
26af098e0e ipq40xx: qcom_scm: Fix cold boot address command
See my upstream questions:
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/

This effectively reverts upstream Linux commit 13e77747800e ("firmware:
qcom: scm: Use atomic SCM for cold boot"), because Google WiFi boot
firmwares don't support the atomic variant.

This fixes SMP support for Google WiFi.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-03-25 18:14:13 +01:00
Brian Norris
a93ec36630 ipq40xx: qcom_scm: Disable SDI at boot
See my upstream RFC of this:
https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/

This fixes warm boot (reboot) for Google WiFi devices using their
factory bootloader/firmware.

I may resend this upstream eventually.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-03-25 18:14:13 +01:00
Brian Norris
17b05045bd ipq40xx: Support Chromium OS image-type creation
See firmware-utils.git commits [1], which implemented the cros-vbutil
verified-boot payload-packing tool, and extended ptgen for the CrOS
kernel partition type. With these, it's now possible to package kernel +
rootfs to make disk images that can boot a Chrome OS-based system (e.g.,
Chromebooks, or even a few AP models).

Regarding PARTUUID= changes: Chromium bootloaders work well with a
partition number offset (i.e., relative to the kernel partition), so
we'll be using a slightly different root UUID line.

NB: I've made this support specific to ip40xx for now, because I only
plan to support an IPQ4019-based AP that uses a Chromium-based
bootloader, but this image format can be used for essentially any
Chromebook, as well as the Google OnHub, a prior Chromium-based AP using
an IPQ8064 chipset.

[1]
ptgen: add Chromium OS kernel partition support
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=6c95945b5de973026dc6f52eb088d0943efa96bb

cros-vbutil: add Chrome OS vboot kernel-signing utility
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=8e7274e02fdc6f2cb61b415d6e5b2e1c7e977aa1

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-03-25 18:14:13 +01:00
Christian Lamparter
4ce52de450 ipq40xx: disable non-building tel(co Electronics) x1pro
Tel(co Electronics) X1 Pro is preventing ipq40xx generic
from building due to the KERNEL_SIZE.

Whenever bigger kernels are possible, if lzma is supported
is unknown.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-25 18:14:13 +01:00
Nicholas Smith
7ea2f3d6e2 ipq40xx: add support for Telco X1 Pro
Telco X1 Pro is a Cat12 LTE-A Pro modem router.
Vendor firmware is based on a recent version of OpenWrt.
Flashing is possible via CLI using sysupgrade -F -n
The serial headers allow bootloader and console access
Serial setting: 115200  8N1

Brief Specifications:
IPQ4019 SoC
32MB flash
512MB RAM
4x gigabit LAN
1x gigabit WAN
Dual-band Wave-2 wifi
2x SMA LTE antenna connectors
2x RP-SMA wifi antennas
1x USB 2.0 port
1x Reset button
Serial headers installed
1x Nano SIM tray
1x Quectel EM-12G LTE-A Pro modem
1x M.2 slot attached to USB 3.0
1x internal micro SD card slot

Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
2022-03-19 20:05:00 +01:00
Rui Salvaterra
72d2c54ccb kernel: 5.10: allocate last level PTEs in high memory
Enable support for allocating user space page table entries in high memory [1],
for the targets which support this feature. This saves precious low memory
(permanently mapped, the only type of memory directly accessible by the kernel).

[1] https://www.kernel.org/doc/html/latest/vm/highmem.html

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-03-01 22:57:34 +00:00
John Audia
a2d4b5711a kernel: bump 5.10 to 5.10.101
Removed upstreamed:
  pending-5.10/841-USB-serial-option-add-ZTE-MF286D-modem.patch[1]
  bcm27xx/950-0592-drm-vc4-Allow-DBLCLK-modes-even-if-horz-timing-is-od.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.101&id=7113440a36c741efd7c76e3d70b3634100120cdb
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.101&id=21c890ca8eaecea06cabb92be2a53a6f26f56383

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-03-01 21:38:36 +01:00
Robert Marko
c1e06a0cbb ipq40xx: mikrotik: fix LED script
Fix the missing ;; after the cAP ac case in /e/b/01_leds.

Fixes: 93d9119 ("ipq40xx: add MikroTik cAP ac support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (minor touch-up)
2022-02-20 14:24:43 +01:00
Christian Lamparter
80d34d9d59 ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200
Enrico provided a bootlog that shows the chip is a WAVE-2 QCA9888v2:

> pci 0000:01:00.0: [168c:0056] type 00 class 0x028000
> [...]
> ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x56.
> ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 [...] chip_id 0x00000000 sub 0000:0000
> ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5  features mfp,[...]
> ath10k_pci 0000:01:00.0: board_file api 2 bmi_id N/A crc32 6535d835
> ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 32 raw 0 hwcrypto 1

this patch switches the device over to pre-calibration.
(this is more or less cosmetic)

Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-19 18:29:42 +01:00
Enrico Mioso
7270c9f8f6 ipq40xx: limit available radio channels for GL.iNet GL-B2200
The PCIe and built-in 5GHZ radios are meant to operate on different
frequency bands. The hardware enforces this via RF filters.
Add this information to allow software enforcing it as well.
Credits to Piotr Dymacz for the invaluable help.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2022-02-19 18:29:42 +01:00
John Audia
c391dcdf86 kernel: bump 5.10 to 5.10.100
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-02-11 23:17:40 +01:00
Julien Cassette
2c1f8a665e ipq40xx: add Linksys MR8300 WAN port
This makes the WAN interface and port appear in
LuCi -> Network -> Switch on Linksys MR8300.
This allows to configure a VLAN on WAN.

Fixes: FS#4227

Signed-off-by: Julien Cassette <julien.cassette@gmail.com>
2022-02-05 00:44:35 +01:00
Pawel Dembicki
a91ab8bc05 ipq40xx: add support for ZTE MF286D
ZTE MF286D is a LTE router with four gigabit ethernet ports
and integrated QMI mPCIE modem.

Hardware specification:

  - CPU: IPQ4019
  - RAM: 256MB
  - Flash: NAND 128MB + NOR 2MB
  - WLAN1:  Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
  - WLAN2:  Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2
  - LTE: mPCIe cat 12 card (Modem chipset MDM9250)
  - LAN: 4 Gigabit Ports
  - USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem)
  - Serial console: X8 connector 115200 8n1

Known issues:

  - Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs
    are driven by cpu.
  - Wifi LED is triggered by phy0tpt only
  - No VoIP support
  - LAN1/WAN port is configured as WAN
  - ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN
    and WLAN0/1

Opening the case:

1. Take of battery lid (no battery support for this model, battery cage
   is dummy).
2. Unscrew screw placed behind battery lid.
3. Take off back cover. It attached with multiple plastic clamps.
4. Unscrew four more screws hidden behind back case.
5. Remove front panel from blue chassis. There are more plastic
   clamps.
6. Unscrew two boards, which secures the PCB in the chassis.
7. Extract board from blue chassis.

Console connection (X8 connector):

1. Parameters: 115200 8N1
2. Pin description: (from closest pin to X8 descriptor to farthest)
    - VCC (3.3V)
    - TX
    - RX
    - GND

Install Instructions:

Serial + initramfs:
1. Place OpenWrt initramfs image for the device on a TFTP in
   the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to X8 connector.
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:
	setenv serverip 192.168.1.3
	setenv ipaddr 192.168.1.72
	set fdt_high 0x85000000
	tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
	bootm $loadaddr
5. Please make backup of original partitions, if you think about revert
   to stock.
6. Login via ssh or serial and remove stock partitions:
	ubiattach -m 9
	ubirmvol /dev/ubi0 -N ubi_rootfs
	ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. Install image via "sysupgrade -n".

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cosmetic changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-02-05 00:44:35 +01:00
Rui Salvaterra
1343acc8cd kernel: bump 5.10 to 5.10.94
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0669-drm-vc4-hdmi-Make-sure-the-device-is-powered-with-CE.patch [1]
bcm27xx/patches-5.10/950-0672-drm-vc4-hdmi-Move-initial-register-read-after-pm_run.patch [1]
gemini/patches-5.10/0003-ARM-dts-gemini-NAS4220-B-fis-index-block-with-128-Ki.patch [2]

Manually rebased:
bcm27xx/patches-5.10/950-0675-drm-vc4-hdmi-Drop-devm-interrupt-handler-for-CEC-int.patch

Manually reverted:
generic/pending-5.10/860-Revert-ASoC-mediatek-Check-for-error-clk-pointer.patch [3]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.94&id=55b10b88ac8654fc2f31518aa349a2e643b37f18
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.94&id=958a8819d41420d7a74ed922a09cacc0ba3a4218
[3] https://lore.kernel.org/all/trinity-2a727d96-0335-4d03-8f30-e22a0e10112d-1643363480085@3c-app-gmx-bap33/

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-02-01 23:34:07 +00:00
Alar Aun
70eedac9b3 ipq40xx: add MikroTik cAP ac support
This adds support for the MikroTik RouterBOARD RBcAPGi-5acD2nD
(cAP ac), a  indoor dual band, dual-radio 802.11ac wireless AP, two
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/cap_ac for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 128 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
   · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 port,
   PoE in and passive PoE out

Unsupported:
 - PoE out

Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"

Signed-off-by: Alar Aun <alar.aun@gmail.com>
2022-02-01 23:18:58 +01:00
Sungbo Eo
81a561b4a6 kernel: move bootargs-append patch to generic
This moves bootargs-append support patch from ipq40xx and ipq806x to
generic. This way we can append additional boot arguments from DTS instead
of only being able to overwrite them.

This is a preparation for kirkwood support of ipTIME NAS1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-29 23:50:28 +09:00
Robert Marko
b8ef54f5da ipq40xx: drop 5.4 kernel
Since 5.10 is now default, no point in keeping
5.4 around.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-01-24 12:07:42 +01:00
Sungbo Eo
266b5c83c3 ipq40xx: rename RT-AC42U WLAN/LAN LEDs
Assign LED numbers properly by adding function-enumerator property in DTS.

While at it, remove default trigger of LAN LEDs as it will be handled in
01_leds anyway.

Fixes: 51b9aef553 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-17 20:38:43 +09:00
Sungbo Eo
e257405c1b ipq40xx: image: remove unused DTB_SIZE variable
It is not included in DEVICE_VARS anyways.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-17 20:38:43 +09:00
Christian Lamparter
0a852d8a5e ipq40xx: AP-365: fix non-existent node or label "macaddr_mfginfo_1d"
Chen Minqiang reported on github:
|  DTC     arch/arm/boot/dts/qcom-ipq4029-ap-365.dtb
|qcom-ipq4019.dtsi:520.23-560.5: ERROR (phandle_references): /soc/wifi@a000000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
|  also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:243.8-248.3
|qcom-ipq4019.dtsi:562.23-602.5: ERROR (phandle_references): /soc/wifi@a800000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
|  also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:250.8-256.3
|ERROR: Input tree has errors, aborting (use -f to force output)
|scripts/Makefile.lib:326: recipe for target 'qcom-ipq4029-ap-365.dtb' failed

Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-16 13:14:58 +01:00
Christian Lamparter
cfc13c4459 ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data
moves extraction entries out of 11-ath10k-caldata and into
the individual board's device-tree.

Some notes:
 - mmc could work as well (not tested)
 - devices that pass the partitions via mtdparts
   bootargs are kept as is
 - gl-b2200 has a weird pcie wifi device
   (vendor claims 9886 wave 2. But firmware-extraction
   was for a wave 1 device?!)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:26:55 +01:00
Christian Lamparter
10bc55c496 ipq40xx: add RT-ACRH13 alternative name to RT-AC58U
RT-ACRH13 is another name this device was sold as (US?).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:26:55 +01:00
Joshua Roys
51b9aef553 ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U
SOC:	IPQ4019
CPU:	Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
DRAM:	256 MB
NAND:	128 MiB Macronix MX30LF1G18AC
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN)
USB:	1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
WLAN2:	Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4
INPUT:	1x WPS, 1x Reset
LEDS:	Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN

This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed
with an intermediary initramfs image, the jffs2 ubi volume deleted, and
then finally a sysupgrade with the final image performed.

Signed-off-by: Joshua Roys <roysjosh@gmail.com>
(added ALT0)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-15 17:21:01 +01:00
Oskari Lemmela
8441a622ec mikrotik: enable variable size erase
Add support for variable size erase blocks.
Enable it to all targets which has mikrotik targets.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2022-01-13 09:33:29 +01:00
John Audia
7bf62e2451 kernel: bump 5.4 to 5.4.169
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*Had to revert 7f1edbd in order to build due to FS#4149

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-03 01:00:03 +01:00
Sergey Ryazanov
fa3690f8f1 kernel: 5.10: consolidate mac80211 crypto options
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2

either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.

CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sergey Ryazanov
b61ab8f57e kernel: filter out both Clang and LLD versions
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Felix Fietkau
01bebc070c kernel: backport the upstream implementation of threaded NAPI to 5.4
The workqueue based implementation has a few corner cases and typically lower
performance than the upstream one

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-12-15 20:36:22 +01:00
John Audia
6c945fa379 kernel: bump 5.10 to 5.10.83
Removed upstreamed:
    bcm53xx/patches-5.10/033-v5.16-0024-ARM-dts-BCM5301X-Fix-I2C-controller-interrupt.patch[1]
    bcm53xx/patches-5.10/033-v5.16-0025-ARM-dts-BCM5301X-Add-interrupt-properties-to-GPIO-no.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=b2cd6fdcbe0a5cb44e4610a08cc58261d494a885
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=9db1d4a3c2700e1cc84c3d61199411d75c2a3ec6

Build system: x86_64*
Build-tested: bcm2711/RPi4B, ipq806x/R7800†
Run-tested: bcm2711/RPi4B, ipq806x/R7800†

* Had to revert 7c99085bd6 in order to build
  (latest bump of ca-certificates)

† Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-12 21:11:30 +01:00
Enrico Mioso
a725bdc700 ipq40xx: fix reset button GPIO for GL.iNet GL-B2200
GL.iNet's U-Boot checks for GPIO 40, not 43.
Changing this allows the RESET button to work as expected.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
2021-12-12 19:14:16 +00:00
Christian Lamparter
d641a60478 ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUP
introduce nvmem pre-cal + mac-address cells for both Wifis
and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of
the few devices in which the correct mac adress is already
at the right place for Wifi, so no separate nvmem cell is
needed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Christian Lamparter
45eb57f12f ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10
with current images, the device is no longer booting.
It gets stuck in the bootloader with "Config not available"
and drops to the uboot shell.

|flash_type: 0
|Hit any key to stop autoboot:  0
|SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB
|Config not availabale
|(IPQ40xx) #

This is because the default bootcmd "bootipq" will only read
the first four MiB of the kernel image. With 5.10 the gzip'd
kernel is slightly larger. So the part of the FIT image which
had the configuration is cut off. Hence it can't find it.

To update the bootcmd, you have to attach the serial console
again and enter the following commands into the boot prompt:

 # setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm"
 # saveenv
 # run bootcmd

This will allow booting kernels with up to six MiB. This also
allows us to drop the DEVICE_DTS_CONFIG hack we had to use.

Note:
uboot doesn't support LZMA. It fails with:
"Unimplemented compression type 3"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-12-04 00:36:47 +01:00
Bjørn Mork
8ac8c09f5e ipq40xx: sysupgrade: drop disabled UBI to UBI logic
The commented out code is not required, as the comment
indicates.

The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-03 12:23:02 +01:00
TruongSinh Tran-Nguyen
febc2b831f
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router.

Specifications:
  - SOC: Qualcomm IPQ4019 ARM Quad-Core
  - RAM: 512 MiB
  - Flash: 16 MiB NOR - SPI0
  - EMMC: 8GB EMMC
  - ETH: Qualcomm QCA8075
  - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
  - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
  - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
  - INPUT: Reset, WPS
  - LED: Power, Internet
  - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
  - UART2: On board with BLE module
  - SPI1: On board socket for Zigbee module

Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.

What's working:
- WiFi 2G, 5G
- WPA2/WPA3

Not tested:
- Bluetooth LE/Zigbee

Credits goes to the original authors of this patch.

V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-12-02 20:43:07 +00:00
Alexander Couzens
8d62304785
ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dish
LHGG-60ad is IPQ4019 + wil6210 based.

Specification:

- Qualcomm IPQ4019 (717 MHz)
- 256 MB of RAM (DDR3L)
- 16 MB (SPI NOR) of flash
- 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035.
- WLAN: wil6210 802.11ad PCI card
- No USB or SD card ports
- UART disabled
- 8x LEDs

Biggest news is the wil6210 PCI card.
Integration for its configuration and detection has already been taken
care of when adding support for TP-Link Talon AD7200.
However, signal quality is much lower than with stock firmware, so
probably additional board-specific data has to be provided to the
driver and is still missing at the moment.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[Fix Ethernet Interface]
Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-12-02 19:46:14 +00:00
Felix Matouschek
1cc3b95efc ipq40xx: Add support for Teltonika RUTX10
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.

The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.

See https://teltonika-networks.com/product/rutx10 for more info.

Hardware:
  SoC:                 Qualcomm IPQ4018
  RAM:                 256MB DDR3
  SPI Flash 1:         XTX XT25F128B (16MB, NOR)
  SPI Flash 2:         XTX XT26G02AWS (256MB, NAND)
  Ethernet:            Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
  WiFi 1:              Qualcomm QCA4019 IEEE 802.11b/g/n
  Wifi 2:              Qualcomm QCA4019 IEEE 802.11a/n/ac
  USB Hub:             Genesys Logic GL852GT
  Bluetooth:           Qualcomm CSR8510 (A10U)
  LED/GPIO controller: STM32F030 with custom firmware
  Buttons:             Reset button
  Leds:                Power (green, cannot be controlled)
                       WiFi 2.4G activity (green)
                       WiFi 5G activity (green)

MACs Details verified with the stock firmware:
   eth0:             Partition 0:CONFIG Offset: 0x0
   eth1:             = eth0 + 1
   radio0 (2.4 GHz): = eth0 + 2
   radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.

The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt

USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.

Flash instructions via stock web interface (sysupgrade based):
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted
  5. Open stock web interface at http://192.168.1.1
  6. Set some password so the web interface is happy
  7. Go to firmware upgrade settings
  8. Choose
     openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
  9. Set 'Keep settings' to off
  10. Click update, when warned that it is not a signed image proceed

Return to stock firmware:
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted

Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.

Signed-off-by: Felix Matouschek <felix@matouschek.org>
2021-11-28 18:39:01 +01:00
Robert Marko
3ad229db0b ipq40xx: add support for MikroTik hAP ac3
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a  indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.

See https://mikrotik.com/product/hap_ac3 for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4019
 - RAM: 256 MB
 - Storage: 16 MB NOR + 128 MB NAND
 - Wireless:
   · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
   · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
 - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
             passive PoE in, PoE passtrough on port 5
- 1x USB Type A port

Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"

Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
2021-11-28 17:19:52 +01:00
Christian Lamparter
c3b9d0d1e2 ipq40xx: utilize nvmem on Netgear EX61X0 v2 Series
the Netgear EX6100v2 and EX6150v2 can utilize the nvmem
for the pre-calibration and mac-address for both WIFI
devices.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-28 01:13:08 +01:00
Christian Lamparter
a5b80dd487 ipq40xx: purge clk_ignore_unused bootarg
these flags have been creeping in from the QSDK.
All needed clocks should be accounted for, and
if a device is broken due to this. It should be
looked into.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-27 23:56:29 +01:00
Christian Lamparter
db7a392ade ipq40xx: update 105-ipq40xx-fix-sleep-clock.patch
Bjorn Anderson has suggestions which would help to upstream the patch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-27 23:56:29 +01:00
Christian Lamparter
e7d0dce2b3 ipq40xx: fix missing include
This patch fixes a blunder of mine. The include needed
for LED_COLOR_ID_BLUE property is missing.

This caused the builds to fail with:
|Error: arch/arm/boot/dts/qcom-ipq4019-r619ac.dtsi:91.13-14 syntax error
|FATAL ERROR: Unable to parse input tree

Fixes: 12d33d388c ("ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-14 19:21:55 +01:00
Christian Lamparter
cb18b62206 ipq40xx: reenable Zyxel NBG6617 by default
The Zyxel NBG6617 already uses lzma to compress the kernel.
A local build with every module enabled (either as =Y or =M)
ended produced a 3058 KiB kernel (the kernel partition is 4MiB).
It booted just fine, let's reenable the device.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-14 14:29:47 +01:00
Richard Yu
12d33d388c ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.

Specification:

* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
  - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
  - 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot

Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
   <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
   `sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install

Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.

This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
   but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
   working. This fix is from
   <51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
   wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.

About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>

About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>

Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-14 14:28:34 +01:00
John Audia
a50565157e kernel: bump 5.4 to 5.4.158
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-07 19:58:08 +01:00
Pawel Dembicki
07543d00e5 ipq40xx: use zImage for Cell-C RTL30VW
After switch to 5.10 kernel, kernel size was too high.
This patch switches Cell-C RTL30VW from uImage to zImage build.

Lzma uImage wrap is required for factory booting and it must left
untouched.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-11-06 23:36:32 +01:00
Robert Marko
605d280914 ipq40xx: 5.10: refresh config
It looks like CONFIG_BLK_CMDLINE_PARSER was forgotten during the Orbi
device merge.
So lets refresh the config with it.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-11-06 23:36:32 +01:00
Rui Salvaterra
4b26ba4155 kernel: bump 5.10 to 5.10.77
Deleted (upstreamed):
bcm53xx/patches-5.10/081-v5.15-Revert-pinctrl-bcm-ns-support-updated-DT-binding-as-.patch [1]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=01c2881bb0e0a71b87ca425e1b763ac13855aa7e

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-11-06 14:24:07 +01:00
Robert Marko
ae7c2bb61b ipq40xx: disable some devices due to kernel size
Disable some of the ipq40xx devices due to their kernel size limitations.

These devices fail to build with kernel 5.10 and full buildbot config.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[keep gl-b1300/gl-s1300 enabled, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-11-03 23:50:56 +01:00
Adrian Schmutzler
16af6535fa ipq40xx: switch to kernel 5.10
There have been enough tests and new developments require the new
kernel, so let's update it.

There is a bunch of devices that do not build anymore due to
kernel size limitations. These are disabled in a subsequent commit.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-11-03 23:50:56 +01:00
Davide Fioravanti
2cb24b3f3c ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50
The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.

This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.

Hardware
--------
SoC:   Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM:   512MB DDR3
FLASH: 4GB EMMC
ETH:
  - 3x 10/100/1000 Mbps Ethernet
  - 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
  - 2.4GHz: 1x IPQ4019 (2x2:2)
  - 5GHz:   1x IPQ4019 (2x2:2)
  - 5GHz:   1x QCA9984 (4x4:4)
  - 6 internal antennas
BTN:
  - 1x Reset button
  - 1x Sync button
  - 1x ON/OFF button
LEDS:
  - 8 leds controlled by TLC59208F (they can be switched on/off
    independendently but the color can by changed by GPIOs)
  - 1x Red led (Power)
  - 1x Green led (Power)
UART:
  - 115200-8-N-1

Everything works correctly.

Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.

The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.

There are 2 ways to install Openwrt the first time:

1) Using NMRPflash
 1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
 2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
	file in the same folder of the nmrpflash executable
 3. Connect your pc to the router using the port near the power button.
 4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
	Replace XXX with your network interface (can be identified by
	running "nmrpflash -L")
 5. Power on the router and wait for the flash to complete. After about
	a minute the router should boot directly to Openwrt. If nothing
	happens try to reboot the router. If you have problems flashing
	try to set "10.164.183.253" as your computer IP address

2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.

To switch on partition 2 you have to enable telnet first:
 1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
 2. Connect through telent ("telnet 192.168.1.250") and login using
	admin/password.

	To read the current boot_part:
		artmtd -r boot_part

	To write the new boot_part:
		artmtd -w boot_part 02

	Then reboot the router and then check again the current booted
	partition

Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.

Restore OEM Firmware
--------------------
 1. Download the stock firmware from official netgear support.
 2. Follow the nmrpflash procedure like above, using the official
	Netgear firmware (for example SRS60-V2.2.1.210.img)

        nmrpflash -i XXX -f SRS60-V2.2.1.210.img

Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
	the UART connection.
	"boot_partition_show" shows the current boot partition
	"boot_partition_set 1" sets the current boot partition to 1

2) Router mac addresses:

   LAN XX:XX:XX:XX:XX:69
   WAN XX:XX:XX:XX:XX:6a
   WIFI 2G XX:XX:XX:XX:XX:69
   WIFI 5G XX:XX:XX:XX:XX:6b
   WIFI 5G (2nd) XX:XX:XX:XX:XX:6c

   LABEL XX:XX:XX:XX:XX:69

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-01 00:56:51 +01:00
Davide Fioravanti
24efb49ff0 ipq40xx: enable CONFIG_CMDLINE_PARTITION and CONFIG_LEDS_TLC591XX
CONFIG_CMDLINE_PARTITION:
Some devices with mmc like the Netgear Orbi Pro SRS60 or Netgear Orbi
RBR50 needs to hardcode the partitions layout in the cmdline boot
correctly

CONFIG_LEDS_TLC591XX:
This is needed for the led driver found in the Netgear Orbi Pro SRS60

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Shang Jia <jiash416@gmail.com>
[added 5.10 config]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-11-01 00:56:51 +01:00
Pavel Kubelun
78be2741aa ipq40xx: fix sleep clock
It seems like sleep_clk was copied from ipq806x.
Fix ipq40xx sleep_clk to the value QSDK defines.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [5.4+5.10]
2021-11-01 00:56:51 +01:00
Christian Lamparter
fd717f54be ipq40xx: detangle ath10k-board-qca4019 from ath10k-firmware-qca4019*
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")

|  2. updating ath10k-firmware-qca4019 will also replace
|      the board-2.bin. For this cases the user needs to
|      manually reinstall the wifi-board package once the
|      ath10k-firmware-qca4019 is updated.

This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-30 16:32:59 +02:00
Matthew Hagan
e3c47ff90d kernel: 5.10: backport qca8k stability improvements
This is a backport of Ansuel Smith's "Multiple improvement to qca8k stability"
series. The QCA8337 switch is available on multiple platforms including
ipq806x, ath79 and bcm53xx.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2021-10-24 16:56:17 +02:00
Tan Zien
85a42fa9cb ipq40xx: MR33: Fix LP5562 LED driver probe
Add the reg and color property to each channel node. This update is
to accommodate the multicolor framework.

Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>

Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[replaced links to lore, wrote something of a commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-10-23 18:50:25 +02:00
Szabolcs Hubai
81d694e30b ipq40xx: use zImage for GL.iNet GL-B1300, GL-S1300 to shrink below 4096k
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.

While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage

Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.

The gzip compressed version would be 4116k.

[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-10-10 16:47:41 +02:00
Robert Marko
7b1fa276f5 ipq40xx: add testing support for kernel 5.10
Add kernel 5.10 as the testing kernel to ipq40xx to
get wider testing.

The following devices failed to build with buildbot settings and all
feeds installed (apparently due to kernel size):

 * cell-c rtl30vw
 * compex wpj428
 * devolo magic 2 next
 * engenius emr3500
 * glinet gl-b1300
 * glinet gl-s1300
 * qcom ap-dk01.1-c1
 * qcom ap-dk04.1-c1

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Nick Hainke <vincent@systemli.org> [ipq4019/fritzbox-7530
                                               ipq4019/fritzbox-4040
                                               ipq4019/sxtsq-5ac]
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ipq4029/gl-b1300]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq4019/map-ac2200]
[add tested-by and note about failed devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-25 19:28:54 +02:00
Robert Marko
f4fb63d2ab ipq40xx: 5.10: move AR40xx to MDIO drivers
MDIO drivers were moved into their own sub directory of networking drivers.
This has caused the AR40xx driver to probe before MDIO drivers and that wont
work as it depends on the MDIO bus to be up so it can be fetched.

Lets solve it by moving the AR40xx into MDIO folder so they get probed like
before.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
ccf214a408 ipq40xx: net: ethernet: edma: reject unsupported coalescing params
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.

This driver did not previously reject unsupported parameters.

This is a required ethtool op since kernel 5.7.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
603848cad8 ipq40xx: net: ethernet: edma: update of_get_phy_mode() for 5.10
In kernel v5.5 of_get_phy_mode had its API changed, so its now returning 0
or errors instead of phymode.

Phymode is now returning by passing a pointer to phy_interface_t where it
will be stored.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
80f007fdb2 ipq40xx: 5.10: add kernel config
Copy config from 5.4 and run "make kernel_oldconfig".

Select default ("N") for all new symbols.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[make commit message more explicit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-25 19:28:54 +02:00
Robert Marko
e9559182b9 ipq40xx: 5.10: refresh patches to apply
Refresh the kernel patches on top of 5.10 so they apply.
Manually fixup the 705-net-add-qualcomm-ar40xx-phy.patch
to apply.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
fec22cfa59 ipq40xx: 5.10: replace patches with upstreamed versions
USB and SDHCI LDO DTS patches have been upstreamed into 5.12, so
replace the local versions with upstreamed ones.

Reorder, and clearly mark the kernel version.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
75a90f161e ipq40xx: 5.10: remove duplicate GPIO export patch
Its in the generic target already, so remove the duplicate
as it breaks compilation.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
9fe5516ee5 ipq40xx: 5.10: drop upstreamed patches
Drop patches that have been upstreamed in before 5.10.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
Robert Marko
8f27ac5ec0 ipq40xx: 5.10: copy patches
Copy over the 5.4 kernel patches to 5.10 folder.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-09-25 19:28:54 +02:00
John Audia
51c7e1d25f kernel: bump 5.4 to 5.4.144
Manually rebased:
  backport-5.4/370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-09-13 17:08:17 +02:00
Sven Eckelmann
c7e9335e4c ipq40xx: Fix board-2.bin package name for Plasma Cloud PA2200
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.

Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
d0ffc17535 ipq40xx: Fix board-2.bin package name for Plasma Cloud PA1200
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.

Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
14bd392a1c ipq40xx: Select correct board-2.bin for EnGenius EMR3500
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.

Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Sven Eckelmann
d9f4a4280e ipq40xx: Select correct board-2.bin for EnGenius EMD1
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.

Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-09-12 18:52:30 +02:00
Hauke Mehrtens
b9cc16a5e8 kernel: Set CONFIG_RCU_CPU_STALL_TIMEOUT=21
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.

This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-09 20:24:12 +02:00
Rui Salvaterra
505b7a2d08 kernel: move two symbols to the generic kconfigs
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-08-29 17:07:19 +02:00
Stijn Tintel
a43da1be43 ipq40xx: fix Edgecore ECW5211 boot
The bootloader will look for a configuration section named ap.dk01.1-c2
in the FIT image. If this doesn't exist, the device won't boot.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-08-18 16:11:11 +03:00
David Bauer
4d81f08771 ipq40xx: ar40xx: reset port status register
This resolves incosnsitencies of the configured RX / TX flow control
modes between different boards or bootloaders.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-14 14:48:07 +02:00
David Bauer
685c790e9f ipq40xx: ar40xx: use FIELD_GET macro
This improves code readability.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-14 14:47:51 +02:00
David Bauer
b9162a9c85 ipq40xx: increase EX6150v2 SPI frequency
The chip supports clock speeds up to 50 MHz, however it won't even read
the chip-id correctly at this frequency.

45 MHz however works reliable.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-08-14 14:47:34 +02:00
Ansuel Smith
91a52f22a1 treewide: backport support for nvmem on non platform devices
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-08-05 01:46:26 +02:00
Ansuel Smith
821b664099 ipq40xx: convert mtd-mac-address to nvmem implementation
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-07-19 14:51:22 +02:00
David Bauer
f9d1828105 ipq40xx: fix FRITZRepeater 1200 RGMII delay
When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the
at803x PHY driver incorrectly set up the delays, not disabling delays
set by the bootloader.

The PHY was always operating with RX as well as TX delays enabled, but
with kernel 5.4 and later, the required TX delay is disabled, breaking
ethernet operation.

Correct the PHY mode, so the driver enables both delays.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-07-17 20:06:49 +02:00
Dmitry Tunin
88f39b72da ipq40xx: increase SPI frequency for Zyxel NBG6617
The mx25l25635f supports clock speed up to 50Mhz.

Also remove obsolete "mx25l25635f" hack and rename
the matching device-tree flash node.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
[mention node rename as well. chip is very very likely
always the "f" revision for all NBG6617]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-07-11 01:38:52 +02:00
Adrian Schmutzler
cce8d16bf1 treewide: call check-size before append-metadata
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.

While at it, do some obvious wrapping improvements.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-07-10 19:40:10 +02:00
Adrian Schmutzler
fac6096ad6 ipq40xx: add missing case closing symbol
Though not strictly necessary, add the closing symbol to make the
job easier for future developers editing this file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-28 01:06:08 +02:00
Rafał Miłecki
3342d574be ipq40xx: specify FritzBox 7530 LAN port label numbers
This helps managing LAN ports.

Ref: https://forum.openwrt.org/t/openwrt-21-02-0-second-release-candidate/98026/121
Fixes: 95b0c07a61 ("ipq40xx: add support for FritzBox 7530")
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-06-24 09:02:31 +02:00
Tomasz Maciej Nowak
1984a6bbca ipq40xx: add uboot-envtools to default packages
When support for Luma WRTQ-329ACN was added, the instructions for
flashing this device include using tools from uboot-envtools package.
Unfortunately the OpenWrt buildroot system omits packages from
DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE,
CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In
result the official images are without tools mentioned in the
instruction. The workoround for the fashing would be installing
uboot-envtools when booted with initramfs image, but not always the
access to internet is available. The other method would be to issue the
necesary command in U-Boot environment but some serial terminals default
configuration don't work well with pasting lines longer than 80 chars.
Therefore add uboot-envtools to default packages, which adds really
small flash footprint to rootfs, where increased size usually is not an
issue.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2021-06-06 00:26:13 +02:00
Adrian Schmutzler
6f648ed7e6 treewide: remove "+" sign for increment with macaddr_add
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.

[*] As a funny side-fact, copy-pasting has led to almost all
    hotplug.d files using the "+", while nearly all of the
    02_network files are not using it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:54:37 +02:00
Robert Marko
b126d9c3a3 ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.

For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>

Specifications:
SoC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
Flash1:     2 MiB Winbond W25Q16JV SPI-NOR
Flash2:     128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet:   Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
            WAN port active IEEE 802.3af/at PoE in
Wireless1:  Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2:  Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input:      (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs:       Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial:     Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
         The Serial settings are 115200-8-N-1.

Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.

In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.

Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.

Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm

Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:

Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[    1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.

Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[    2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[    2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-06-05 23:29:46 +02:00
Baptiste Jonglez
979f406366 ipq40xx: fix hard_config partition size on MikroTik hAP-ac2
The routerbootparts driver dynamically discovers the location of MikroTik
partitions, but it cannot determine their size (except by extending them
up to the start of the next discovered partition).

The hard_config partition has a default size of 0x1000 in the driver,
while it actually takes 0x2000 on the hAP-ac2.  Set the correct size in
the hAP-ac2 DTS.

On most devices, this isn't a problem as the actual data fits in 0x1000
bytes.  However, some devices have larger data that doesn't fit in 0x1000
bytes.  In any case, all devices seen so far have enough space for a
0x2000 hard_config partition before the start of the dtb_config partition.
With the current 0x1000 size:

0x00000000e000-0x00000000f000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"

With this patch extending the size to 0x2000:

0x00000000e000-0x000000010000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"

Other ipq40xx boards may need the same fix but it needs testing.

References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324
Acked-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2021-05-08 12:18:43 +02:00
John Audia
0d2873df15 kernel: bump 5.4 to 5.4.114
Manually rebased*
  generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch

Added new backport*
  generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch

All others updated automatically.

The new backport was included based on this[1] upstream commit that will be
mainlined soon.  This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93

Signed-off-by: John Audia <graysky@archlinux.us>
2021-04-30 23:48:37 +02:00
Roger Pueyo Centelles
d1f1e5269e ipq40xx: add support for MikroTik SXTsq 5 ac
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 256 MB
 - Storage: 16 MB NOR
 - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
 - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
 - 1x Ethernet LED (green)
 - 7x user-controllable LEDs
  · 1x power (blue)
  · 1x user (green)
  · 5x rssi (green)

Note:
 Serial UART is probably available on the board, but it has not been
 tested.

Flashing:
 Boot via TFTP the initramfs image. Then, upload a sysupgrade image
 via SSH and flash it normally. More info at the "Common procedures
 for MikroTik products" page https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-04-29 10:55:07 +02:00
Rui Salvaterra
3326b5e75c treewide: switch the timer frequency to 100 Hz
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:10 +01:00
Rui Salvaterra
27b5bae2ec treewide: remove redundant ubifs kconfig symbols
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:07 +01:00
Robert Marko
faea7becaf
ipq40xx: add MikroTik hAP ac2 support
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a  indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and  five
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/hap_ac2 for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 128 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
   · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
             passive PoE in
- 1x USB Type A port

Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-04-05 04:13:28 +02:00
Aleksander Jan Bajkowski
12e942b1fd kernel: move some disabled symbols to generic
Move some disabled symbols found in armvirt target to generic.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-03-19 00:59:22 +01:00
Daniel Golle
9690836344 ipq40xx: work-around borked QCA SDK bootloader
The bootloader of many ipq40xx boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq40xx.

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-06 19:05:53 +00:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Robert Marko
7f2d9ccd09 ipq40xx: net: phy: qca807x: fix GPIO driver
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.

Without it using the pins as GPIO-s did not actually work.

Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-03-05 00:28:35 +01:00
Jason A. Donenfeld
196f3d586f kernel-5.4: bump to 5.4.102 and refresh patches
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.

This commit involved `update_kernel.sh -v -u 5.4`.

Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-03-04 22:06:53 +01:00
Paul Spooren
6ab33103af treewide: remove redundant KERNEL_PREFIX definitions
The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already
defined in include/image.mk and don't have to be redefined in the
target Makefiles.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[also cover imx6]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 00:26:40 +01:00
Adrian Schmutzler
5697915a18 ipq40xx: remove generic profile
On a platform with many very different devices, like found on ipq40xx,
the generic profile seems like a remnant of the past that does not
have a real use anymore.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
f52081bcf9 treewide: provide global default for SUPPORTED_DEVICES
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:

  SUPPORTED_DEVICES := $(subst _,$(comma),$(1))

At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:

  device/image name:  vendor_model
  compatible:         vendor,model

The equal redundant definitions are a symptom of this process.

Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.

This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 12:45:21 +01:00
Robert Marko
36347d003a ipq40xx: fix boards being shown twice
Since generic images have been split to their own
Makefile boards are showing up twice in menuconfig
as $(eval $(call BuildImage)) was not dropped from
the new generic.mk.

Hence $(eval $(call BuildImage)) was being called
twice.

So, lets simply drop it from generic.mk.

Fixes: 378c7ff282 ("ipq40xx: split generic images into own file")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-01-21 17:08:16 +01:00
Robert Marko
f4fdd8609c
ipq40xx: mikrotik: enable MikroTik platform driver
This enables the MikroTik platform driver, it enables us to parse
valuable info from hard_config including WLAN calibration data
extraction from sysfs.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:31:56 +01:00
Robert Marko
0184889088 ipq40xx: mikrotik: enable MikroTik NOR parser
Needed for SPI-NOR based MikroTik IPQ40xx devices like hAP ac2.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Robert Marko
30a92f55de ipq40xx: mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTS
This enables the new MikroTik specific partition parser.

This avoids manually specifying the MikroTik specific partitions as they
can be detected by their magic values.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Robert Marko
b779da27ef ipq40xx: add MikroTik subtarget
MikroTik devices require the use of raw vmlinux out of the self
extracting compressed kernels.

They also require 4K sectors, kernel2minor, partition parser as well as
RouterBoard platform drivers.

So in order to not add unnecessary code to the generic sub target lets
introduce a MikroTik sub target.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
John Thomson
10d057f84a ipq40xx: kernel compressed boot: reset watchdog countdown
If the watchdog is enabled, set the timeout to 30 seconds before
decompress is started.

Mikrotik ipq40xx devices running with RouterBoot have the SoC watchdog
enabled and running with a timeout that does not allow time for the
kernel to decompress and manage the watchdog.

On ipq40xx RouterBoot TFTP boot the watchdog countdown is reset before:
Jumping to kernel

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2021-01-17 14:23:05 +01:00
Robert Marko
b6461e4654 ipq40xx: arm: compressed: add appended DTB section
This adds a appended_dtb section to the ARM decompressor
linker script.

This allows using the existing ARM zImage appended DTB support for
appending a DTB to the raw ELF kernel.

Its size is set to 1MB max to match the zImage appended DTB size limit.

To use it to pass the DTB to the kernel, objcopy is used:

objcopy --set-section-flags=.appended_dtb=alloc,contents \
	--update-section=.appended_dtb=<target>.dtb vmlinux

This is based off the following patch:
c063e27e02

Signed-off-by: Robert Marko <robimarko@gmail.com>
2021-01-17 14:23:05 +01:00
Alexander Couzens
378c7ff282
ipq40xx: split generic images into own file
In preparation of the new mikrotik subtarget split the generic images
into generic.mk

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2021-01-17 07:16:23 +01:00
Jan Alexander
6738b5e2ac uboot-envtools: add support for Aruba AP-303 and AP-365
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.

Signed-off-by: Jan Alexander <jan@nalx.net>
2021-01-14 01:04:02 +01:00
Sungbo Eo
aad3d9c710 ipq40xx: remove unnecessary execute permission bit
DTS files do not need to be executable. 644 is enough.

Fixes: 0fbdb51f76 ("ipq40xx: add Edgecore OAP-100 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[split by targets]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-03 15:48:18 +01:00
Adrian Schmutzler
9b1b89229f kernel: bump 5.4 to 5.4.86
Removed upstreamed patches:
  pending-5.4/499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch

Manually merged:
  pending-5.4/611-netfilter_match_bypass_default_table.patch
  layerscape/302-dts-0112-arm64-dts-fsl-ls1028a-prepare-dts-for-overlay.patch

Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/{generic,tiny},
              ipq40xx, octeon, ramips/mt7621, realtek, x86/64
Run-tested: ipq806x/R7800, realtek

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org>
2021-01-01 17:07:28 +01:00
David Bauer
f3e45c45cb ipq40xx: remove non-existent ethernet PHY
Since updating the MDIO driver, the probe will fail hard on any
PHY not present on the bus, while this was not the case prior.

Fixes commit 26b1f72381 ("ipq40xx: net: phy: ar40xx: remove PHY
handling")
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-30 23:41:03 +01:00
Dongming Han
b9389186b0 ipq40xx: add support for GL.iNet GL-AP1300
Specifications:
SOC:        Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:        256 MiB
FLASH1:     4 MiB NOR
FLASH2:     128 MiB NAND
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:      Reset
LED:        Power, Internet
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER:      On board with BLE module - by cp210x USB serial chip
            On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-12-25 10:38:13 +01:00
Robert Marko
fd033364f6 ipq40xx: net: ethernet: edma: use generic PHY print
Lets use the generic upstream phy_print_status() instead of doing 
something similar by hand.

Before:
ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000

After:
ess_edma c080000.edma eth1: Link is Up - 1Gbps/Full - flow control rx/tx

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
9d69505194 ipq40xx: net: ethernet: edma: use generic ksettings functions
Since we now have a proper PHY driver for QCA807x and AR803x has already
been supported properly there is no need for the driver to be poking
on PHY registers for ethtool ops.

So, lets simply use the generic
phy_ethtool_ksettings_get/phy_ethtool_ksettings_set functions.

This also has the advantage of properly populating stuff other than
speeds like, transceiver type, MDI-X etc.

ethtool before:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
                                1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
                                1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: No
        Link partner advertised auto-negotiation: No
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 4
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: Unknown
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

ethtool after:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
                                1000baseX/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
                                1000baseX/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: Symmetric Receive-only
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 4
        Transceiver: external
        Auto-negotiation: on
        MDI-X: off (auto)
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
2a5bfb6600 ipq40xx: dts: convert PHY GPIO bindings
Since the new PHY driver manages each PHY individually and therefore 
registers each PHY that is marked with gpio-controller; DT property as a
GPIO controller we need to convert old DT bindings to account for this.

Only 2 boards use this so its not much of an issue.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
c8af7ea205 ipq40xx: dts: add QCA807x properties
This adds necessary DT properties for QCA807x PHY-s to IPQ4019 DTSI.

Also adds the PSGMII PHY as it wont get probed otherwise.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
053c3d8e0b ipq40xx: net: ethernet: edma: fix link detection
PHY needs to be soft reset before starting it from ethernet driver as
AR40xx calibration will leave it in unwanted state.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
26b1f72381 ipq40xx: net: phy: ar40xx: remove PHY handling
Since we now have proper PHY driver for the QCA807x PHY-s, lets remove
PHY handling from AR40xx.

This removes PHY driver, PHY GPIO driver and PHY init code.
AR40xx still needs to handle PSGMII calibration as that requires R/W
from the switch, so I am unable to move it into PHY driver.

This also converted the AR40xx driver to use OF_MDIO to find the MDIO
bus as it now cant be set through the PHY driver.
So lets depend on OF_MDIO in KConfig.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
b5c93edd74 ipq40xx: add Qualcomm QCA807x driver
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.

They are 2 or 5 port IEEE 802.3 clause 22 compliant
10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s.

They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC,
while second one is SGMII for connection to MAC or fiber.

Both models have a combo port that supports 1000BASE-X and 100BASE-FX
fiber.

Each PHY inside of QCA807x series has 2 digitally controlled output only
pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled by
user space, so lets enable registering each PHY as GPIO controller and
add driver for it.

This also adds the ability to specify DT properties so that 1000 Base-T
LED will also be lit up for 100 and 10 Base connections.

This is usually done by U-boot, but boards running mainline U-boot are
not configuring this yet.

These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
03bae3cafd ipq40xx: edma: convert to of_mdio_find_bus()
With the reworked MDIO driver, EDMA will fail to get the MII BUS as it
used the MII BUS stored inside the MDIO structure private data.

This obviously does not work with the modernized driver, so lets switch
to using a purpose build of_mdio_find_bus() which will return the MII
BUS and only requires the MDIO node to be passed.
This is easy as we already have the node parsed.

Also, since we now require OF_MDIO add that as dependency.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
4cdc8d20fa ipq40xx: backport upstream MDIO driver
IPQ40xx MDIO driver was upstreamed in kernel version 5.8.
So lets backport the upstream version and drop our local one.

This also refreshed the kernel config since the symbol name has changed.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Robert Marko
49795690e6 ipq40xx: refresh kernel config
Generic kernel config changed a lot, so lets refresh ipq40xx
to reduce the diff.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-12-23 16:36:08 +01:00
Stefan Schake
d3c8881194 ipq40xx: add support for devolo Magic 2 WiFi next
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8075 (2 ports)
PLC:     MaxLinear G.hn 88LX5152
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET, WiFi, PLC Button
LEDS:    red/white home, white WiFi

To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
   initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
   the Ethernet ports. This causes the bootloader to retrieve and start
   the initramfs.
3) Once the initramfs is booted, the device will come up with IP
   192.168.1.1. You can then connect through SSH (allow some time for
   the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
   Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
   # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
   and install it with sysupgrade. The device will reboot into OpenWRT.

Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.

Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
2020-12-22 20:55:40 +01:00
Marek Lindner
4871fd2616 ipq40xx: add support for Plasma Cloud PA2200
Device specifications:

* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3at POE+
    + used as WAN interface
* 12V 2A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Marek Lindner
ea5bb6bbfe ipq40xx: add support for Plasma Cloud PA1200
Device specifications:

* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio4:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio3:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3af/at POE(+)
    + used as WAN interface
* 12V/24V 1A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Sven Eckelmann
8a891bfaa0 ipq40xx: Change name for openmesh.sh to vendor-free name
Other vendors are using functionality similar to the ones OpenMesh used to
implement two areas on the flash to store the default image and a fallback
image. So just change the name to dualboot_datachk.sh to avoid duplicated
code just to have the same script for different vendors.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00
Aleksander Jan Bajkowski
77575d4c02 kernel: move some disabled symbols to generic
Move some disabled config options found in lantiq target to generic.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-12-22 19:11:50 +01:00
Moritz Warning
debbc0a8a8 ipq40xx: use upper case for NETGEAR in DEVICE_VENDOR
Adjust spelling of vendor name to what is used in other places.

Also move definition in shared section.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-12-19 19:42:00 +01:00
John Audia
afd4bf08bc kernel: bump 5.4 to 5.4.83
Manually merged:
  layerscape/808-i2c-0011-i2c-imx-support-slave-mode-for-imx-I2C-driver.patch
  layerscape/808-i2c-0012-i2c-imx-correct-code-of-errata-A-010650-for-layersca.patch

Remaining modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86/64 [*],
              ramips/mt7621 [*], ath79/tiny [*], ipq40xx [*], octeon [*],
              realtek [*]
Run-tested: ipq806x/R7800, ramips/mt7621 [*], octeon [*], realtek [*]

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2020-12-15 12:05:26 +01:00
David Bauer
cdc8d4b46f ipq40xx: revert usage of VLAN S-TAG
This reverts the usage of the S-Tag for separating LAN and WAN port on
the embedded switch. Many users complained about not being able to
manage C-Tag addition / removal on the switch as well as degraded
performance.

Fixes: commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging")

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-12-14 01:13:30 +01:00
Yushi Nishida
5e9a5c15ba ipq40xx: fix 5Ghz tx/rx power on the ASUS MAP-AC2200
The ASUS MAP-AC2200 suffers from a lower transmit/receive
signal power as compared to the stock firmware.

Upon investigation, it was discovered that stock firmware from
the GPL_MAP-AC2200_3.0.0.4.384.46249-g97d05bb.tar archive.
set the following GPIOs in "release/src/router/rc/init.c".

GPIO 44 and 46 have to be set to output high
GPIO 45 and 47 have to be set to output low

Here are some results, after activating the relevant
gpios through cmdline:

<https://forum.openwrt.org/t/asus-map-ac2200-low-transmit-receive-signal-5ghz/69005/12>

THX @ slh

Fixes: 9ad3967f14 ("ipq40xx: add support for ASUS Lyra")
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
[slightly rewritten commit, added missing <>)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-12-13 16:12:45 +01:00
Sven Eckelmann
8231994d3f ipq40xx: DTS style updates for OpenMesh devices
The OpenMesh related files were not updated since a while and the new
coding style requirements weren't integrated. This can cause problems
for new devices when an author uses these files as starting point.

* use SPDX-License-Identifiers instead of full license texts
* drop linux,default-trigger with value default-off for LEDs
* led nodes with label "abc:xyz" should have name "xyz_abc"
* led DT labels for "xyz_abc" should be "led_xyz_abc"
* "m25p80@0" flash node should be renamed to "flash@0"
* drop unnecessary empty lines

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[minor commit title and message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-23 13:44:47 +01:00
John Audia
667f6c7f49 kernel: bump 5.4 to 5.4.77
Manually rebased patches:
 bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch
 generic-backport/744-v5.5-net-sfp-soft-status-and-control-support.patch
 layerscape/patches-5.4/819-uart-0005-tty-serial-fsl_lpuart-enable-dma-mode-for-imx8qxp.patch
 mvebu/patches-5.4/521-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch

Removed:
 layerscape/patches-5.4/819-uart-0012-tty-serial-lpuart-add-LS1028A-support.patch

All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711,
              lantiq/Easybox 904 xDSL, x86_64
Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL, x86_64

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-11-18 21:13:46 +01:00