Commit Graph

114 Commits

Author SHA1 Message Date
Sungbo Eo
a972b1fb5f ramips: add support for ipTIME A6ns-M
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7615
  - 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- UART:
  - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-12-13 19:42:48 +01:00
Sungbo Eo
0375c076b6 ramips: add support for ZIO FREEZIO
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7603EN
  - 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1x 3.0
- UART:
  - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.

MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)

Installation via web interface:
1.  Access web admin page and turn on "OpenWrt UI mode".
2.  Flash sysupgrade image through LuCI, with the "Keep settings" option
    OFF.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.
    Make sure to NOT preserve settings.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-13 15:37:37 +01:00
Adrian Schmutzler
68ef534989 ramips: add label MAC address for Mikrotik RBM33G
The device label contains:
E01: B8:69:F4:xx:xx:07
E02: B8:69:F4:xx:xx:09

The first value corresponds to the address set in hard_config 0x10.

That one is taken for the label MAC address.

Thanks to Martin Schiller for retrieving the information.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:12:11 +01:00
Adrian Schmutzler
ed975a58e4 ramips: mt7621: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:28 +01:00
Adrian Schmutzler
38866f275d ramips: remove wan_mac setup for evaluation boards
The evaluation boards do not set up a MAC address for eth0
in the first place, so it does not make sense to calculate a WAN
address from the random MAC used there.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:11:11 +01:00
Gabor Varga
a283b1788a ramips: fix switch port numbering for RT-AC65P/RT-AC85P
The switch LAN port numbers are in reversed order with original config.
With this patch they are fixed.

Port order checked on both devices.

Signed-off-by: Gabor Varga <vargagab@gmail.com>
[merged definitions into appropriate block, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-11 23:00:32 +01:00
Martin Schiller
3a55c7935d ramips: fix number of LAN Ports for Mikrotik RBM33G
The Mikrotik RBM33G has only 2 LAN ports.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 00:20:21 +01:00
Piotr Dymacz
e68539aca4 ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.

Specification:

- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)

Other:

- U-Boot selects default SIM slot, based on value of 'default_sim' env
  variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
  has additional logic circuit for M.2 SIM switching. The 'sim-select'
  will work only if both SIM slots are occupied. Otherwise, always slot
  with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
  loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
  U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
  has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
  miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
  slots but setting GPIO22 to high allows PERSTn control per slot, using
  GPIO23-25 (value is inverted)

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the modem LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-14 01:37:54 +01:00
Adrian Schmutzler
f4c3cfc620 ramips: read label MAC address from flash instead of using phy0/phy1
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 12:51:38 +01:00
Adrian Schmutzler
1c321237c2 ramips: split further base-files across subtargets
As started in 19724e28c8 ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:

- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-11 14:53:06 +01:00
Sungbo Eo
62b1559b56 ramips: improve support for WeVO 11AC NAS and W2914NS v2
- remove WAN port index
- load WAN MAC address directly from the flash
- provide label MAC address
- increase flash's SPI frequency to 80MHz
- add mt76 led nodes to make WiFi LEDs work
- drop unnecessary pinmux groups

The factory partition scheme for MAC addresses (verified on both devices):
0x4   : WiFi 2.4GHz (label_mac-9)
0x28  : unused
0x2e  : WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-5)
0xe000: LAN (label_mac-1)
0xe006: unused

By improving flash speed,
`time dd if=/dev/mtdblock3 of=/dev/null bs=64k`
has been reduced from 14.51s to 3.11s.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:31:32 +01:00
Adrian Schmutzler
d2b9333ea9 ramips: remove default case for MAC address assignment
So far, MAC address assignment in ramips has contained a default
case, which defined wan_mac = eth0 + 1 for _every_ device not
having an explicit case there.

This is not desirable, as many device supporters will just not
care or know about this definition, so another MAC address will be
introduced by accident. In some cases the wan_mac is assigned
although it is not needed, in other cases even addresses not
dedicated to the device will be used (e.g. wan_mac actually is
eth0 - 1, but during support nobody cared, so eth0 + 1 is used now,
which might actually belong to another device ...).

Thus, in this PR the former default case is converted to an
explicit case. This one comprises all devices not being accounted
for by other cases, reduced by those not having wan at all.
The big number of entries for this node might be another indication
that many of them wouldn't actually be there if there hadn't been
default wan_mac setup.

In exchange, the current "do nothing" case can be removed, as it
will be the new default case.

The devices being put in the newly created explicit case were
determined as follows:

1. Create a list of all devices based on the DTS files.

2. Remove all devices already having an explicit entry setting
   their address.

3. Remove all devices that only have lan set up in the first part
   of 02_network:

mt7620:
   - alfa-network,tube-e4g
   - asus,rp-n53
   - buffalo,wmr-300
   - comfast,cf-wr800n
   - edimax,ew-7476rpc
   - edimax,ew-7478ac
   - elecom,wrh-300cr
   - hnet,c108
   - kimax,u25awf-h1
   - kimax,u35wf
   - kingston,mlw221
   - kingston,mlwg2
   - microduino,microwrt
   - netgear,ex2700
   - netgear,ex3700
   - netgear,wn3000rp-v3
   - planex,cs-qr10
   - planex,mzk-ex300np
   - planex,mzk-ex750np
   - ravpower,wd03
   - sercomm,na930
   - yukai,bocco
   - zbtlink,zbt-cpe102
   - zte,q7

mt7621:
   - gnubee,gb-pc1
   - gnubee,gb-pc2
   - linksys,re6500
   - mikrotik,rbm11g
   - netgear,ex6150
   - thunder,timecloud
   - tplink,re350-v1
   - tplink,re650-v1

mt76x8:
   - alfa-network,awusfree1
   - d-team,pbr-d1
   - glinet,vixmini
   - vocore,vocore2-lite
   - tama,w06
   - tplink,tl-mr3020-v3
   - tplink,tl-wa801nd-v5
   - tplink,tl-wr802n-v4
   - tplink,tl-wr902ac-v3
   - vocore,vocore2
   - widora,neo-16m
   - widora,neo-32m

rt288x:
   - buffalo,wli-tx4-ag300n
   - dlink,dap-1522-a1

rt305x:
   - allnet,all0256n-4m
   - allnet,all0256n-8m
   - allnet,all5002
   - allnet,all5003
   - alphanetworks,asl26555-16m
   - alphanetworks,asl26555-8m
   - asus,wl-330n
   - aximcom,mr-102n
   - dlink,dcs-930
   - easyacc,wizard-8800
   - hame,mpr-a2
   - hootoo,ht-tm02
   - huawei,d105
   - intenso,memory2move
   - planex,mzk-dp150n
   - rt305x dlink,dcs-930l-b1
   - sparklan,wcr-150gn
   - tenda,3g150b
   - tenda,3g300m
   - tenda,w150m
   - trendnet,tew-638apb-v2
   - unbranded,a5-v11
   - vocore,vocore-16m
   - vocore,vocore-8m
   - wansview,ncs601w
   - zorlik,zl5900v2

rt3883:
   - loewe,wmdr-143n
   - omnima,hpm

4. Put the remaining devices in the new case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 13:17:25 +01:00
Sungbo Eo
763914ef1b ramips: improve netis WF-2881 support
This patch does the following:

1. remove u-boot-env partition
   Stock bootloader saves env variables at 0x80000 in flash,
   and there is nothing stored at 0x30000.
   By merging the partition "u-boot-env" with "u-boot",
   the partition table becomes the same as used in stock firmware:
   00000000-00080000: "Bootloader"
   00080000-00100000: "Config"
   00100000-00140000: "Factory"
   00140000-07f80000: "Kernel"

2. fix LAN/WAN MAC addresses and provide label MAC address
   Ethernet MAC addresses are stored in factory partition at:
   0xe000: LAN (label_mac)
   0xe006: WAN (label_mac+1)

3. fix LAN port order
   WF-2881 LAN ports are in reverse order of switch ports.

4. fix WiFi LEDs
   mt76 led nodes are added to make WiFi LEDs work.
   On top of this, mt76 node names are changed to more generic ones,
   and compatible strings are also added.

5. fix pinmux groups
   uart3 and uart2 pins are used as button and led, but jtag pins are not.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-06 00:27:55 +01:00
Adrian Schmutzler
19724e28c8 ramips: split base-files into subtargets
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.

However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space.

In certain cases, keeping files in parent (=target) base-files was
more convenient, and thus no splitting was performed for those.

Note that this will increase overall code lines, but reduce code
per subtarget.

base-files ipk size reduction:
master (mt7621)   60958 B
split (mt7620)    46358 B (- 14.3 kiB)
split (mt7621)    48759 B (- 11.9 kiB)
split (mt76x8)    44948 B (- 15.6 kiB)
split (rt288x)    43508 B (- 17.0 kiB)
split (rt305x)    45616 B (- 15.0 kiB)
split (rt3883)    44176 B (- 16.4 kiB)

Run-tested on:
GL.iNet GL-MT300N-V2 (mt76x8)
D-Link DWR-116 (mt7620)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:26:17 +01:00