Commit Graph

640 Commits

Author SHA1 Message Date
Yangbo Lu
b4b53cd39b layerscape: drop armv8_32b support
NXP LSDK has decided to drop armv8_32b support considering
few users are using it.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-06-06 15:40:08 +02:00
Biwen Li
4b4b686b1d layerscape: update u-boot to LSDK 19.03
Update u-boot to LSDK 19.03.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2019-06-06 15:40:08 +02:00
Sandeep Sheriker M
a765a2178c at91:renaming subtraget legacy to sam9x
renaming subtraget legacy to sam9x for adding new sam9 soc's

Signed-off-by: Sandeep Sheriker M <sandeep.sheriker@microchip.com>
2019-05-30 12:12:57 +02:00
Hauke Mehrtens
aff084adf3 at91: Merge SAMA5 subtargets
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
2019-05-30 12:12:37 +02:00
Petr Štetiar
049748e87e uboot-imx6: bump to 2019.04 and refresh patches
Build tested: apalis, mx6sabresd, nitrogen6dl, nitrogen6dl2g, nitrogen6q,
	      nitrogen6q2g, nitrogen6s, nitrogen6s1g, wandboard

Run tested: apalis

Cc: Felix Fietkau <nbd@nbd.name>
Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-20 21:19:48 +02:00
Hauke Mehrtens
df6e8c8771 uboot-fritz4040: Add host flags for host compiler
This adds the host staging directory to the include path to make it use
the zlib.h files from the staging include directory and also link
against the zlib version from the staging directory.

This fixes a compile problem when the zlib header were not installed on
the build host.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[picked from openwrt-18.06]
2019-05-19 12:29:24 +02:00
sven friedmann
30dcbc741d ath79: add support for EnGenius ECB1750
Specification:

- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)

https://fccid.io/A8J-ECB1750

Tested and working:

- lan, wireless, leds, sysupgrade (tftp)

Flash instructions:

1.) tftp recovery

- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade

2.) oem webinterface factory install (not tested)

Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".

3.) oem webinterface command injection

OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.

https://openwrt.org/toh/engenius/engenius_ecb1750_1

Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
2019-05-18 13:43:55 +02:00
Jeff Kletsky
819e7946b0 ipq40xx: Add support for Linksys EA8300 (Dallas)
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.

Installation:

  "Factory" images may be installed directly through the OEM GUI.

Hardware Highlights:

  * IPQ4019 at 717 MHz (4 CPUs)
  * 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
  * 256 MB RAM
  * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
      * 2.4 GHz radio at 30 dBm
      * 5 GHz radio on ch. 36-64 at 23 dBm
      * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
      #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
      * All two-stream, MCS 0-9
  * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
  * USB3, single port on rear with LED
  * WPS and reset buttons
  * Four status lights on top
  * Serial pads internal (unpopulated)

  "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"

Implementation Notes:

  The OEM flash layout is preserved at this time with 3 MB kernel and
  ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
  syscfg (56 MB) partitions are untouched, available as read-only.

Serial Connectivity:

  Serial connectivity is *not* required to flash.

  Serial may be accessed by opening the device and connecting
  a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
  including the ability to load images over TFTP and
  either run or flash them.

  Looking at the top of the board, from the front of the unit,
  J3 can be found on the right edge of the board, near the rear

      |
   J3 |
  |-| |
  |O| | (3.3V seen, open-circuit)
  |O| | TXD
  |O| | RXD
  |O| |
  |O| | GND
  |-| |
      |

Unimplemented:

    * serial1 "ttyQHS0" (serial0 works as console)
    * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)

Other Notes:

    https://wikidevi.com/wiki/Linksys_EA8300 states

        FCC docs also cover the Linksys EA8250. According to the
	RF Test Report BT BR+EDR, "All models are identical except
	for the EA8300 supports 256QAM and the EA8250 disable 256QAM."

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-18 13:43:54 +02:00
Tomasz Maciej Nowak
e7756974aa tegra: add vendor string to device name
for better identification. Also create SUPPORTED_DEVICES string from it
which corresponds to dts compatible string.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-15 13:34:23 +02:00
Tomasz Maciej Nowak
ee96fa15b1 mvebu: use device-tree board detection
Convert whole target to Device Tree based board detection instead of
identifying devices by dts file name. With this we can drop mvebu.sh
translation script and rely on common method for model detection.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
a39d2a8053 mvebu: align device names to vendor_device format
Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-11 23:11:04 +02:00
Tomasz Maciej Nowak
b18d1d5d3f uboot-tegra: bump to 2019.04
This version has important change for tegra boards which is reserving
32MB memory for Linux kernel instead of current 16MB.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-05-05 21:11:01 +02:00
Hauke Mehrtens
675832de79 xburst: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Hauke Mehrtens
e6f9a8e89b au1000: Remove unmaintained target
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-05-03 21:27:12 +02:00
Daniel Golle
44ae5f37fb uboot-envtools: fix fw_env.config for ox820/stg-212
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-04-11 19:21:55 +02:00
Daniel Gimpelevich
f61e754522 ath79: add support for Netgear EX6400 and EX7300
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.

Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A

Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-09 11:09:26 +02:00
Petr Štetiar
adb0a420e5 uboot-envtools: imx6: Add support for Toradex Apalis board family
This patch is needed in order to be able to use fw_{set,print}env
commands.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:03 +02:00
Petr Štetiar
136001675e uboot-imx6: Add support for Toradex Apalis board family
This patch is needed in order to properly boot OpenWrt bootscript.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:03 +02:00
Michael Heimpold
007e947976 fconfig: cleanup Makefile
We do not need to define an empty Build/Configure since
the default checks for existing ./configure and does nothing
in case nothing is found.

Similar for Build/Compile: we can remove the definition
when we only call the default.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-04-06 19:14:06 +02:00
Tomasz Maciej Nowak
1b3dda179a uboot-tegra: add U-Boot for tegra boards
Add U-Boot for NVIDIA Tegra based boards, with the first being CompuLab
TrimSlice. This is part of initial support for this board.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 14:48:46 +02:00
Alexander Couzens
95f07502b7
package/uboot-omap: backport patches to fix build
* 106: fix build when libfdt-devel is installed on host
* 107: fix stdbool.h includes

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-03-28 02:10:12 +01:00
Christian Lamparter
41bceb0d4e uboot-fritz4040: fix PKG_MIRROR_HASH
The PKG_MIRROR_HASH was for some reason wrong.

Fixes: d75db67870 ("uboot-fritz4040: bump version to 2019-03-03")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
Ozgur Can Leonard
201d3d1a82 ramips: Xiaomi MIR3G: detect board name from DTS
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
  Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
Zoltan HERPAI
5e247f3ac1 uboot-sunxi: add fix for A20-OLinuXino-Lime2-eMMC rev. K boards
The OLinuXino Lime2 rev. K boards use new PHYs (Micrel KSZ9031),
so enable that.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2019-03-13 22:43:13 +01:00
Zoltan HERPAI
e991fb44e0 uboot-sunxi: bump to 2019.01
Tested on:
Bananapro (A20)
Banana Pi M3 (A83t)
Linksprite pcDuino3 (A20)
Olinuxino Lime (A10)
Orange Pi 2 (H3)
Pine64 (A64)

Patches refreshed.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2019-03-13 22:42:38 +01:00
David Bauer
148d29d47b ipq40xx: add support for AVM FRITZ!Repeater 3000
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH:   Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED:    - Connect green/blue/red
        - Power green
BTN:   WPS/Connect
UART:  115200n8 3.3V
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ3000.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz3000.bin uboot0
   > mtd write /path/to/uboot-fritz3000.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:35 +01:00
David Bauer
d75db67870 uboot-fritz4040: bump version to 2019-03-03
Adds support for the AVM FRITZ!Repeater 3000

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:34 +01:00
Ozgur Can Leonard
d009033911 ramips: add support for Xiaomi Mi Router 3 Pro
Hardware:

CPU:   MediaTek MT7621AT (2x880MHz)
RAM:   512MB DDR3
FLASH: 256MB NAND
WiFi:  2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI:  5GHz 4x4 MT7615 a/n/ac  (Needs driver, See Issues!)
USB:   1x 3.0
ETH:   1x WAN 10/100/1000 3x LAN 10/100/1000
LED:   Power/Status
BTN:   RESET
UART:  115200 8n1

Partition layout and boot:

Stock Xiaomi firmware has the MTD split into (among others)

- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)

Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.

Note uboot's tftp flash install writes the transferred
image to both kernel partitions.

Installation:

Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.

The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:

nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot

Reverting to stock:

The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.

For this we do the following:

fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot

After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.

Issues:

OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.

See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
2019-03-13 16:25:34 +01:00
Santiago Piccinini
24463d0d94 ath79: add support for LibreRouter v1
Hardware
--------
SOC:   QCA9558
RAM:   128M DDR2
Flash: 16MiB SPI-NOR
ETH:   QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN:   1x Reset
GPIO:  multiple GPIO on header, PoE passthrough enable
UART:  3.3V 115200 8N1 header on the board
WDG:   ATTiny13 watchdog
JTAG:  header on the board
USB:   1x connector and 1x header on the board
PoE:   10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)

OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.

Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
   header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
   interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
    ath> tftp 82000000 <your image>-sysupgrade.bin
    ath> erase 0x9f050000 +$filesize
    ath> cp.b 0x82000000 0x9f050000 $filesize
    ath> bootm 0x9f050000

More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
2019-03-13 16:25:34 +01:00
Piotr Dymacz
82dbcd8bf2 uboot-envtools: ramips: add support for ALFA Network Tube-E4G
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Aleksander Jan Bajkowski
445ca981d1 sunxi: add support for Orange Pi PC Plus
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 1GB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard: Storage 8 GB eMMC
Onboard: Network 10/100M Ethernet RJ45
Onboard: Network WiFi 802.11 b/g/n (Realtek RTL8189FTV)
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: Three USB 2.0 HOST, One USB 2.0 OTG

Known issues:
-Wifi diesn't work

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2019-03-09 18:55:15 +01:00
Piotr Dymacz
c5394ec7e0 uboot-envtools: ath79: add support for YunCore A770
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-09 16:31:22 +01:00
Daniel Golle
9a9c6f37d5 uboot-envtools: oxnas: sync with current oxnas/ox820 DTS
Use tested values on shuttle,kd20 and assumed values for
mitrastar,stg-212 and cloudengines,pogoplug*.
akitio users have yet to report back stock flash layout to support
vendor bootloader environment there as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-03-01 03:36:53 +01:00
David Bauer
95b0c07a61 ipq40xx: add support for FritzBox 7530
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M
FLASH: 128M NAND
ETH:   QCA8075
VDSL:  Intel/Lantiq VRX518 PCIe attached
       currently not supported
DECT:  Dialog SC14448
       currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED:    - Power/DSL green
        - WLAN green
        - FON/DECT green
        - Connect/WPS green
        - Info green
        - Info red
BTN:    - WLAN
        - FON
        - WPS/Connect
UART:  115200n8 3.3V (located under the Dialog chip)
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ7530.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz7530.bin uboot0
   > mtd write /path/to/uboot-fritz7530.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:32:55 +01:00
David Bauer
93b02ad95e uboot-fritz4040: bump version to 2019-02-08
Adds support for the AVM FRITZ!Box 7530.

Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [PKG_RELEASE]
2019-02-28 11:32:55 +01:00
Aleksander Jan Bajkowski
00d89b4a89 sunxi: add support for Orange Pi One
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 512MB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2019-02-26 23:20:04 +01:00
Piotr Dymacz
9bf63d0339 uboot-envtools: add support for ALFA Network AP120C-AC
While at it, fix alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:16:22 +01:00
Paul Wassi
dc08514e6d uboot-kirkwood: update to 2019.01
Update U-Boot to current 2019.01 release for kirkwood platform

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-17 19:22:39 +01:00
Pawel Dembicki
d5f615bf2a sunxi: add support for Sinovoip Banana Pi M2 Plus
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 1GB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard: Network 10/100M Ethernet RJ45 (Realtek RTL8211E)
Onboard: Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212)
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: Two USB 2.0 HOST, One USB 2.0 OTG

Untested:
Audio, Video

Not working:
Bluetooth

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-02-17 19:22:39 +01:00
Tomasz Maciej Nowak
bb0e4f9fb0 build: remove leftovers from previous x86 commits
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6  image: use internal qemu-img for vmdk and vdi images drop host
         dependencies on qemu-utils and VirtualBox

Unreachable config symbols:
9e0759e  x86: merge all geode based subtargets into one

No need to define those symbols since x86_64 is subtarget of x86:
196fb76  x86: make x86_64 a subtarget instead of a standalone target

Unreachable config symbols, so remove GRUB_ROOT:
371b382  x86: remove the xen_domu subtarget

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-02-17 18:22:40 +01:00
Andre Heider
4b403821c6
uboot-omap: add 'rootwait' to the kernel cmdline
Some SD cards take a while to get detected, fix booting of those.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2019-01-31 14:07:00 +01:00
Petr Štetiar
c2bdd018a3 uboot-imx6: Bump to 2019.01
Build tested: apalis, mx6sabresd, nitrogen6dl, nitrogen6dl2g, nitrogen6q,
              nitrogen6q2g, nitrogen6s, nitrogen6s1g, wandboard

Run tested: apalis (pending PR #1595)

Cc: Felix Fietkau <nbd@nbd.name>
Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-01-26 21:46:32 +01:00
Michael Heimpold
52d7a1d3b2 uboot-mxs: bump to v2019.01
Also update the U-Boot BSP patch for I2SE Duckbill devices.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-01-26 21:46:32 +01:00
Oever González
ad3e667539 uboot-envtools: add support for Linksys EA6350v3
This commit adds support for the Linksys EA6350v3 device in the ipq40xx
target.

This is needed for uboot-envtools to access the environment. Without this
patch, the Linksys EA6350v3 will not be able to access the uboot
environment. As a side effect, the feature auto_recovery will make the
device unstable by switching between the latest and the current firmware.

Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
2019-01-26 21:43:04 +01:00
Christian Lamparter
47c3ada44a uboot-fritz4040: update package to 2019-01-25
David Bauer reported a u-boot crash (data abort) at a odd
place (byteswap) when he ran ping/tftp on his 7530.

|(FRITZ7530) # ping 192.168.1.70
|eth0 PHY0 up Speed :1000 Full duplex
|eth0 PHY1 Down Speed :10 Half duplex
|eth0 PHY2 Down Speed :10 Half duplex
|eth0 PHY3 Down Speed :10 Half duplex
|eth0 PHY4 Down Speed :10 Half duplex
|Using eth0 device
|data abort
|pc : [<84234774>]      lr : [<842351a4>]
|sp : 8412fdb0  ip : 0000009b     fp : 00000000
|r10: 00000000  r9 : 00000001     r8 : 8412ff68
|r7 : 00000000  r6 : 0000002a     r5 : 84244e90  r4 : 8425e28e
|r3 : 84244e90  r2 : 14000045     r1 : 8412fdb0  r0 : 8425e28e
|Flags: nZCv  IRQs off  FIQs off  Mode SVC_32
|Resetting CPU ...
|
|resetting ...

This issue is caused by switch from gcc 5.5 to 7.1+ as explained
in the upstream patch:

|From a768e513b07b5999a8e7d7740ac8d9da04ee7e51 Mon Sep 17 00:00:00 2001
|From: Denis Pynkin <denis.pynkin@collabora.com>
|Date: Fri, 21 Jul 2017 19:28:42 +0300
|Subject: [PATCH] net: Use packed structures for networking
|
|PXE boot is broken with GCC 7.1 due option '-fstore-merging' enabled
|by default for '-O2':
|
|BOOTP broadcast 1
|data abort
|pc : [<8ff8bb30>]          lr : [<00004f1f>]
|reloc pc : [<17832b30>]    lr : [<878abf1f>]
|sp : 8f558bc0  ip : 00000000     fp : 8ffef5a4
|r10: 8ffed248  r9 : 8f558ee0     r8 : 8ffef594
|r7 : 0000000e  r6 : 8ffed700     r5 : 00000000  r4 : 8ffed74e
|r3 : 00060101  r2 : 8ffed230     r1 : 8ffed706  r0 : 00000ddd
|Flags: nzcv  IRQs off  FIQs off  Mode S
|
|Core reason is usage of structures for network headers without packed
|attribute.

Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-26 21:09:12 +01:00
David Bauer
b368373fab mpc85xx: add support for OCEDO Panda
CPU:   FSL P1020 (2x 800MHz E500 PPC)
RAM:   1GB DDR3
FLASH: 256MiB NAND
WiFi:  2x Atheros AR9382 2x2:2 abgn
ETH:   2x BCM54616S - 1x BCM53128 8-port switch
LED:   5x LEDs (Power, WiFi1, WiFi2, N/D, SYS)
BTN:   1x RESET

Installation
------------

1. Download initrams kernel image, dtb binary and sysupgrade image.

2. Place initramfs kernel into tftp root directory. Rename to
"panda-uimage-factory".

3. Place dtb binary into tftp root directory. Rename to "panda.fdt".

4. Start tftp server on 192.168.100.8/24.

5. Power up the device with the reset button pressed. It will download
the initrams and dtb via tftp and boot into OpenWRT in RAM.

6. SSH into the device and remove the factory partitions.

 > ubirmvol /dev/ubi0 --name=kernel1
 > ubirmvol /dev/ubi0 --name=rootfs1
 > ubirmvol /dev/ubi0 --name=devicetree1

You will have around 60 MiB of free space with that.

You can also delete "kernel2", "devicetree2", "rootfs2" and "storage"
respectively in case you do not want to go back to the vendor firmware.

7. Modify the U-Boot bootcmd to allow for booting OpenWRT

 > fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel
   && bootm 0x1000000"

 > fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200
   ubi.mtd=3,2048"

 > fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt"

8. Transfer the sysupgrade image via scp into the /tmp directory.

9. Upgrade the device

 > sysupgrade -n /tmp/<imagename>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 17:10:19 +01:00
Andy Walsh
45a2771953 uboot-ar71xx: fix musl host build
On musl based distributions, u-boot 2010.03 fails to build with:

    u-boot-2010.03/include/u-boot/crc.h:29:50: error: unknown type name 'uint'
      uint32_t crc32 (uint32_t, const unsigned char *, uint);

The issue was fixed in the newer u-boot-2018.03 version, this commit
backports the change to the older version used by ar71xx/ath79.

Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[add commit message from PR description]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-22 13:29:46 +01:00
Hauke Mehrtens
d560deb7f2 uboot-sunxi: Orange Pi Zero Plus: Fix SdCard detection
The Detection pin is at PF6 and not at PH13 like defined before. I
checked the schematics and now I am am not seeing this error message any
more:
Loading Environment from FAT... Card did not respond to voltage select!

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:35:14 +01:00
Zoltan HERPAI
7a53fb40ca uboot-sunxi: disable AXP209 on Olimex A13 Olinuxino
Disable the PMIC on Olimex A13 Olinuxino, as the SPL cannot set the
core voltage correctly, which causes the board to freeze later at
kernel if CPU throttling is enabled (see below). This will almost
certainly kill the VGA output (which requires LDO3 to be set), but
this is still a better option than to disable CPU throttling for
all Cortex-A8 based devices.

[    2.485632] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 384000 KHz
[    2.525698] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 432000 KHz

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2019-01-13 17:35:14 +01:00
Zoltan HERPAI
d605831068 uboot-sunxi: update Theobroma A31 Pangolin support
Drop removed pinctrl definitions from the i2c3 pin layout.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2019-01-13 17:35:14 +01:00