Commit Graph

52993 Commits

Author SHA1 Message Date
Tamas Balogh
b29f4cf34c ath79: add support for ASUS RP-AC66
Asus RP-AC66 Repeater

Hardware specifications:
Board: AP152
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 25l128 16MB SPI-NOR
LAN/WAN: 1x1000M QCA8033
WiFi 5GHz: QCA9880
Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz

MAC addresses as verified by OEM firmware:
use            address   source
Lan/Wan   *:24         art 0x1002 (label)
2G             *:24         art 0x1002
5G             *:26         art 0x5006

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the factory image
    and press upload
 - Do not power off the device after OpenWrt has booted until the LED flashing.

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put factory.bin
 tftp> quit

Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
2022-01-09 20:32:41 +01:00
Stijn Tintel
0f50d3daff firewall4: bump to git HEAD
9a509d4 ruleset.uc: consolidate ip and ip6 offload
 21f311d ruleset.uc: don't trim newline before comment sign
 f121383 tests: enable flow offloading in tests
 550df40 tests: add test for unknown defaults option
 47c5a5b tests: add test for deprecated rule option
 69a89d6 tests: add test for unknown rule option
 07579df fw4.uc: handle interface zone option

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-09 17:38:18 +02:00
Fritz D. Ansel
693958497a mediatek mt7622: fix 300mhz typo in dts
The lowest frequency should be 300MHz, since that is the label
assigned to the OPP in the mt7622.dtsi device tree, while there is one
missing zero in the actual value.

To be clear, the lowest frequency should be 300MHz instead of 30MHz.

As mentioned @dangowrt on the OpenWrt forum there is no benefit in
leaving 30MHz as the lowest frequency.

Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com>
Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
2022-01-09 14:48:16 +00:00
Stefan Lippers-Hollmann
abc2821286 x86: improve sysinfo handling of dummy values
Fall back to using board_vendor and board_name, if known dummy values
are used for sys_vendor and product_name.

Examples:
	To be filled by O.E.M.:To be filled by O.E.M.
-->	INTEL Corporation:ChiefRiver

	System manufacturer:System Product Name
-->	ASUSTeK COMPUTER INC.:P8H77-M PRO

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:Q1900DC-ITX

	Gigabyte Technology Co., Ltd.:To be filled by O.E.M.
-->	Gigabyte Technology Co., Ltd.:H77M-D3H

	empty:empty
-->	TYAN Computer Corporation:TYAN Toledo i3210W/i3200R S5211

	To Be Filled By O.E.M.:To Be Filled By O.E.M.
-->	ASRock:H77 Pro4-M

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2022-01-08 23:25:05 +01:00
Alex Lewontin
62a2bfaff8 ipq806x: janitorial work, respect line lengths
This commit breaks up some lines so that they are shorter than
74 charcters.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Alex Lewontin
479acf03cc ipq806x: modularize generic subtarget
This commit moves the device profiles within the ipq806x/generic
subtarget into their own includable .mk file, to support eventually
having subtargets other than generic.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2022-01-08 23:25:05 +01:00
Josef Schlehofer
31647d8be8 kernel: add kmod-usb-net-lan78xx
Add kernel module for Microchip LAN78XX based USB 2 & USB 3
10/100/1000 Ethernet adapters. [1]

This kernel module is required for the Seeed Studio's Mini Router
based on RPI CM4 [2].

[1] <https://cateee.net/lkddb/web-lkddb/USB_LAN78XX.html>
[2] <https://www.seeedstudio.com/Dual-GbE-Carrier-Board-with-4GB-RAM-32GB-eMMC-RPi-CM4-Case-p-5029.html>

Link: <https://github.com/openwrt/openwrt/pull/4893>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(added kmod-phy-microchip and kmod-fixed-phy dependencies,
rpi3 needs lan78xx but has it built-in)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-08 23:23:22 +01:00
Christian Lamparter
3fabca8894 kernel: provide kmod-fixed-phy as separate kmod
Almost all targets have the fixed-phy feature built into the kernel.
One big exception is x86. This caused a problem with the upcoming
LAN78xx usb driver. Hence this patch breaks out the fixed-phy from
of_mdio (which didn't include the .ko) and puts into a separate
module.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-08 23:20:21 +01:00
Christian Lamparter
d9ff9a4270 kernel: add kmod-phy-microchip
phy drivers for Microchip's LAN88xx PHYs.
This is needed for the "LAN7801" variant
of the upstream lan78xx usb ethernet driver.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-01-08 23:17:18 +01:00
Hirokazu MORIKAWA
8c501bf9fe toolchain/binutils: v2.37 Close the file descriptor if there is no archive fd
This fixes the following build error:
/home/build/openwrt/staging_dir/toolchain-aarch64_cortex-a53_gcc-11.2.0_musl/lib/gcc/aarch64-openwrt-linux-musl/11.2.0/../../../../aarch64-openwrt-linux-musl/bin/ld: /home/sergey/openwrt2/build_dir/target-aarch64_cortex-a53_musl/node-v14.18.2/out/Release/obj.target/tools/v8_gypfiles/libv8_base_without_compiler.a: error adding symbols: malformed archive
collect2: error: ld returned 1 exit status

It's a bad error handling related to -EMFILE (too many open files). nodejs is probably just very close to open file limit.

https://sourceware.org/bugzilla/show_bug.cgi?id=28138
https://github.com/nodejs/node/issues/39452

https://github.com/openwrt/packages/issues/17496
https://github.com/openwrt/packages/issues/16729
https://github.com/openwrt/packages/issues/17164

Signed-off-by: Hirokazu MORIKAWA <morikw2@gmail.com>
[Take full patch from 2.37 branch and refresh]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-08 21:37:45 +01:00
Aleksander Jan Bajkowski
46468fc9d5 lantiq: replace patches with version accepted upstream
Replace recently added patches with version accepted upstream.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-01-08 19:32:45 +01:00
Florian Fainelli
a372946e60 elfutils: Add missing musl-fts dependency
libdw depends on libfts.so when building with the musl-libc library, add
this missing dependency.

Fixes: 6835ea13f0 ("elfutils: update to 0.186")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2022-01-07 20:50:50 -08:00
Marty Jones
3fe253c6ab linux-firmware: add new package r8152-firmware
Linux upstream commit 9370f2d05a
add load firmware file through request_firmware,this affect the
nanopi r2s and some USB adapters in kernel 5.10 with this error:
'r8152 4-1:1.0: unable to load firmware patch rtl_nic/rtl8153b-2.fw'
This patch split the USB NIC firmware files from r8169 firmware,
and adds r8152-firmware to r8152 driver.
Add kmod-usb-net-cdc-ncm to support RTL8156A and RTL8156B 2.5G ethernet
adapters supported since v5.13-rc1.
195aae321c

Signed-off-by: Marty Jones <mj8263788@gmail.com>
2022-01-08 00:49:59 +01:00
Jan Hoffmann
9d878d8422 ltq-ifxos: update to 1.7.1
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[fix warnings, switch to tag tarball, update patches]
Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-01-08 00:49:59 +01:00
Andre Heider
5ee1e04517 ltq-vdsl: move to the default device name /dev/dsl_cpe_api/0
This makes patching it for ltq-vdsl-app unnecessary and paves the way
for VRX518 support.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-01-08 00:49:59 +01:00
Hannu Nyman
a54b406ccb busybox: update to 1.35.0
Update busybox to 1.35.0

* refresh patches

Config refresh:

Refresh commands, run after busybox is first built once:

cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0/.config > Config-defaults.in

Manual edits needed after config refresh:

* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
  BUSYBOX_DEFAULT_FEATURE_IPV6

* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
  BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)

* Config-defaults.in: OpenWrt logic applied to
  BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)

* config/editors/Config.in: Add USE_GLIBC dependency to
  BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)

* config/shell/Config.in : change at "Options common to all shells" the symbol
  SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
  (discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
  Apparently our script does not see the hidden option while
  prepending config options with "BUSYBOX_CONFIG_" which leads to a
  missed dependency when the options are later evaluated.)

* Edit Config.in files by adding quotes to sourced items in
  config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2022-01-08 00:49:59 +01:00
Glenn Strauss
a8513e2461 mbedtls: enable session tickets
session tickets are a feature of TLSv1.2 and require less memory
and overhead on the server than does managing a session cache

Building mbedtls with support for session tickets will allow the
feature to be used with lighttpd-1.4.56 and later.

Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
2022-01-08 00:49:59 +01:00
Sergey V. Lobanov
6835ea13f0 elfutils: update to 0.186
Upstreamed patches (deleted):
0001-ppc_initreg.c-Incliude-asm-ptrace.h-for-pt_regs-defi.patch -
 https://sourceware.org/git/?p=elfutils.git;a=commitdiff;h=8382833a257b57b0d288be07d2d5e7af6c102869
110-no-cdefs.patch -
 https://sourceware.org/git/?p=elfutils.git;a=commitdiff;h=d390548df1942e98a1d836269a5e41ba52e121f1

Auto-refreshed:
006-Fix-build-on-aarch64-musl.patch
101-no-fts.patch

Manually updated and refreshed:
005-build_only_libs.patch
003-libintl-compatibility.patch
100-musl-compat.patch

Disabled _obstack_free check (via configure vars)

Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
2022-01-08 00:49:59 +01:00
Nick McKinney
e0a574d4b7 ramips: add support for Linksys EA6350 v4
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0

This is another MT7621 device, very similar to other Linksys EA7300
series devices.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Reverting to factory firmware:

Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking.  Hard-resetting this device three (3) times will
put the device in failsafe (default) mode.  At this point, flash the
OEM image to itself and reboot.  This puts the router back into the 'B'
image and allows for a firmware upgrade.

Troubleshooting:

If the firmware will not boot, first restore the factory as described
above.  This will then allow the factory.bin update to be applied
properly.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
2022-01-08 00:49:59 +01:00
Liangkuan Yang
bc7d36ba3a ramips: add support for RAISECOM MSG1500 X.00
RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router.
Apart from the general model, there are two ISP customized models:
China Mobile and China Telecom.

Specifications:

- SoC: Mediatek MT7621AT
- RAM: 256MiB DDR3
- Flash: 128MiB NAND
- Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN
  - Switch: MediaTek MT7530 (SoC)
- WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps)
- USB: 1 * USB 2.0 port
- Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button
- LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB
- UART: 1 * serial port header (4-pin)
- Power: DC 12V, 1A
  - Switch: 1 * POWER switch

MAC addresses as verified by vendor firmware:

use   address             source
LAN   C8:XX:XX:3A:XX:E7   Config   "protest_lan_mac"  ascii  (label)
WAN   C8:XX:XX:3A:XX:EA   Config   "protest_wan_mac"  ascii
5G    C8:XX:XX:3A:XX:E8   Factory  "0x4"              hex
2.4G  CA:XX:XX:4A:XX:E8   [not on flash]

The increment of the 4th byte for the 2.4g address appears to vary.
Reported cases:

       5g                 2.4g         increment
 C8:XX:XX:90:XX:C3  CA:XX:XX:C0:XX:C3  0x30
 C8:XX:XX:3A:XX:08  CA:XX:XX:4A:XX:08  0x10
 C8:XX:XX:3A:XX:E8  CA:XX:XX:4A:XX:E8  0x10

Since increment is inconsistent and there is no obvious pattern
in swapping bytes, and the 2.4g address has local bit set anyway,
it seems safer to use the LAN address with flipped byte here in
order to prevent collisions between OpenWrt devices and OEM devices
for this interface. This way we at least use an address as base
that is definitely owned by the device at hand.

Notes:

1. The vendor firmware allows you to connect to the router by telnet.
   (known version 1.0.0 can open telnet.)
   There is no official binary firmware available.
   Backup the important partitions data:
   "Bootloader", "Config", "Factory", and "firmware".
   Note that with the vendor firmware the memory is detected only 128MiB
   and the last 512KiB in NAND flash is not used.

2. The POWER LED is default on after press POWER switch.
   The WAN and LAN1 - 4 LEDs are wired to ethernet switch.
   The WPS LED is controlled by MT7615DN's GPIO.
   Currently there is no proper way to configure it.

3. At the time of adding support the wireless config needs to be set up
   by editing the wireless config file:

 * Setting the country code is mandatory, otherwise the router loses
   connectivity at the next reboot. This is mandatory and can be done
   from luci. After setting the country code the router boots correctly.
   A reset with the reset button will fix the issue and the user has to
   reconfigure.

 * This is minor since the 5g interface does not come up online although
   it is not set as disabled. 2 options here:

   1- Either run the "wifi" command. Can be added from LuCI in system -
      startup - local startup and just add wifi above "exit 0".

   2- Or add the serialize option in the wireless config file as shown
      below. This one would work and bring both interfaces automatically
      at every boot:

      config wifi-device 'radio0'
          option serialize '1'

      config wifi-device 'radio1'
          option serialize '1'

Flash instructions using initramfs image:

1. Press POWER switch to power down if the router is running.

2. Connect PC to one of LAN ports, and set
   static IP address to "10.10.10.2", netmask to "255.255.255.0",
   and gateway to "10.10.10.1" manually on the PC.

3. Push and hold the WIFI button, and then power up the router.
   After about 10s (or you can call the recovery page, see "4" below)
   you can release the WIFI button.
   There is no clear indication when the router
   is entering or has entered into "RAISECOM Router Recovery Mode".

4. Call the recovery page for the router at "http://10.10.10.1".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   Click "Choose File" to select initramfs image, then click "Upload".

5. If image is uploaded successfully, you will see the page display
   "Device is upgrading the firmware... %".
   Keep an eye on the "WARNING!! tip" of the recovery page.
   When the page display "Upgrade Successfully",
   you can set IP address as "automatically obtain".

6. After the rebooting (PC should automatically obtain an IP address),
   open the SSH connection, then download the sysupgrade image
   to the router and perform sysupgrade with it.

Flash back to vendor firmware:

 See "Flash instructions 1 - 5" above.
 The only difference is that in step 4
 you should select the vendor firmware which you backup.

Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
2022-01-08 00:49:59 +01:00
Rodrigo Araujo
766733e172 ramips: add support for Joowin WR758AC V1 and V2
This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2
devices.

Both have the same wall AP/repeater form factor and differ only
in the 5Ghz chipset (V1 has MT7662, V2 has MT7663).

OpenWrt developers forum page:
https://forum.openwrt.org/t/87355

Specifications:

 - CPU: MediaTek MT7628AN (580MHz)
 - Flash: 8MB
 - RAM: 64MB DDR2
 - 2.4 GHz: 802.11b/g/n (MT7603)
 - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663)
 - Antennas: 4x external single band antennas
 - LAN: 1x 10/100M
 - LED: Wifi 3x blue. Programmable
 - Button: WPS

MAC addresses as verified by OEM firmware:

use address source
LAN *:83 factory 0xe000
2g *:85 factory 0x4
5g *:86 factory 0x8004

How to install:
1- Setup a TFTP server on a machine with IP address 192.168.1.10/24
2- Name the image as `firmware_auto.bin` and place it on the root of the
TFTP server
3- Connect the device via Ethernet, it should pick and flash the image

Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
2022-01-08 00:49:59 +01:00
Sergey V. Lobanov
04e6434c62 utils/mdadm: fix build on hosts without /run dir
CHECK_RUN_DIR=0 must be a part of MAKE_FLAGS, not MAKE_VARS, otherwise
it is not possible to compile mdadm on host without /run dir.

Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
2022-01-08 00:49:59 +01:00
Matthew Hagan
033b6cef94 kernel: enhance multicast routing support
Certain utilities, such as smcroute [1], require additional multicast
routing options to be enabled, otherwise they will not function
correctly. Enable these relevant dependancies when IPv4 and/or IPv6
multicast routing are enabled.

[1] https://github.com/troglobit/smcroute/blob/master/README.md#linux-requirements

This increases the uncompressed kernel size on MIPS 24kc by 8KBytes
and the compressed kernel size by 1.8KBytes.

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2022-01-08 00:48:39 +01:00
Rui Salvaterra
536f051b97 kernel: bump 5.10 to 5.10.90
Add and enable a new kconfig knob to disable unprivileged eBPF by default.

Patches automatically rebased.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-01-07 22:30:40 +01:00
John Audia
9f08557649 kernel: bump 5.4 to 5.4.170
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-07 22:30:40 +01:00
Hauke Mehrtens
77df120bc8 toolchain: glibc: Enable --enable-bind-now
Enable --enable-bind-now when CONFIG_PKG_RELRO_FULL is set. This option
is activated by default. This will enable full RELRO protection.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-07 22:30:40 +01:00
Hauke Mehrtens
1b251d36ef toolchain: glibc: Increase minimum kernel version to 5.4
Increase the minimum kernel version needed by the glibc compiled for
OpenWrt to version 5.4. With this setting the glibc build will remove
all code needed to support older kernel versions.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-07 22:30:40 +01:00
Hauke Mehrtens
e708bf76d5 toolchain: glibc: Update to version 2.34
glibc version 2.34 does not provide versioned shared libraries any more,
it only provides shared libraries using the ABI version. Do not try to
copy them any more.

The functions from libpthread and librt were integrated into the main
binary, the libpthread.so and librt.so are only used for backwards
compatibility any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-01-07 22:30:40 +01:00
Stijn Tintel
4d1f133561 firewall4: bump to git HEAD
main.uc: fix device gathering

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-01-06 21:30:14 +02:00
Jo-Philipp Wich
7881dce7d8 firewall4: fix syntax error in dependency spec
Fixes: ae60af8572 ("firewall4: order DEPENDS alphabetically")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-01-06 16:58:06 +01:00
Stijn Tintel
53b87a7a28 firewall/firewall4: provide uci-firewall
Provide uci-firewall via PROVIDES in both firewall and firewall4. This
will allow us to change the dependency of luci-app-firewall to
uci-firewall, making it possible to use it with either implementation.

Move CONFLICTS from firewall4 to firewall, to solve this recursive
dependency problem:

tmp/.config-package.in:307:error: recursive dependency detected!
tmp/.config-package.in:307:     symbol PACKAGE_firewall is selected by PACKAGE_firewall4
tmp/.config-package.in:328:     symbol PACKAGE_firewall4 depends on PACKAGE_firewall

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2022-01-06 14:54:50 +02:00
Stijn Tintel
3ec25a657d firewall4: bump to git HEAD
4ead2a6 treewide: move executables to /sbin
 9ebc2f4 fw4.uc: filter duplicates in fw4.set
 85b74f3 treewide: support flow offloading
 be3b4e6 treewide: support hardware flow offloading
 38889b7 treewide: support set timeout
 31c7550 fw4.uc: do not skip defaults with invalid option
 334a127 fw4.uc: introduce DEPRECATED flag
 7a0d38f fw4.uc: add _name as deprecated option
 5e7ad3b fw4.uc: don't fail on unknown options
 be5f4e3 fw4.uc: allow use of cidr in ipsets

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2022-01-06 14:54:43 +02:00
Stijn Tintel
ae60af8572 firewall4: order DEPENDS alphabetically
Add some line breaks while at at, to improve readability.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2022-01-06 14:54:06 +02:00
Stijn Tintel
3d4acc34bb firewall4: drop kmod-ipt-nat from CONFLICTS
The limitation of not being able to use iptables and nft nat at the same
time exists only in kernels before 4.18.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
2022-01-06 14:53:47 +02:00
Daniel Kestrel
b61d756b6c ltq-deu: disable arc4 algorithm
ARC4 was used for WEP, which is not secure anymore. Therefor it is
disabled in the driver, but the code is not removed for now.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:15 +01:00
Daniel Kestrel
fc4d88cf73 ltq-deu: add aes_gcm algorithm
The lantiq AES hardware does not support the gcm algorithm. But it
can be implemented in the driver as a combination of the aes_ctr
algorithm and the xor plus gfmul operations for the hashing.
Due to the wrapping of the several algorithms and the inefficient
16 byte block by 16 byte block invokation in the kernel
implementations, this driver is about 3 times faster for the larger
block sizes.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:15 +01:00
Daniel Kestrel
973e28f248 ltq-deu: change PKG_RELEASE to AUTORELEASE
As per suggestion by adschm, PKG_RELEASE is set to AUTORELEASE.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:15 +01:00
Daniel Kestrel
a0d6b09c36 ltq-deu: remove redundant code for setting the key in aes
After adding xts and cbcmac the aes algorithm source had three sections
for setting the aes key to the hardware which are identical.
Method aes_set_key_hw was created which is now called from within the
spinlock secured control sections in methods ifx_deu_aes, ifx_deu_aes_xts
and aes_cbcmac_final_impl and reduces the size of ifxmips_aes.c.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:15 +01:00
Daniel Kestrel
79efaa7f8f ltq-deu: add shash cbcmac-aes algorithm to the driver
Since commit 53b6783 hostapd is using the kernel api which includes the
cbcmac-aes shash algorithm. The kernels implementation is a wrapper around
the aes encryption algorithm, which encrypts block (16 bytes) by block.
When the ltq-deu driver is present, it uses hardware aes, but every 16 byte
encrypt requires setting the key. This is very inefficient and is a huge
overhead. Since the cbcmac-aes is simply a hash that uses the cbc aes
algorithm starting with an iv set to x'00' with an optional ecb aes
encryption of a possible last incomplete block that is padded with the
positional bytes of the last cbc encrypted block, this algorithm is now
added to the driver. Most of the code is derived from md5-hmac and
tailored for aes. Tested with the kernels crypto testmgr including extra
tests against the kernels generic ccm module implementation.
This patch also fixes the overallocation in the aes_ctx that is caused
by using u32 instead of u8 for the aes keys.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:15 +01:00
Daniel Kestrel
f8e5c6080c ltq-deu: remove driver disablement for kernel 5.4 and above
Remove the dependency on kernel 5.4 from the Makefile to allow the
driver to compile with kernel 5.10 or kernel versions higher than
5.4.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:15 +01:00
Daniel Kestrel
43422deed3 ltq-deu: add aes_xts algorithm
The lantiq AES hardware does not support the xts algorithm. Apart
from the cipher text stealing (XTS), the AES XTS implementation is
just an XOR with the IV, followed by AES ECB, followed by another
XOR with the IV and as such can be also implemented by using the
lantiq hardware's CBC AES implemention plus one additional XOR with
the IV in the driver. The output IV by CBC AES is also not usable
and the gfmul operation not supported by lantiq hardware. Both need
to be done in the driver too in addition to the IV treatment which is
the initial encryption by the other half of the input key and to
set the IV to the IV registers for every block.
In the generic kernel implementation, the block size for XTS is set
to 16 bytes, although the algorithm is designed to process any size
of input larger than 16 bytes. But since there is no way to
indicate a minimum input length, the block size is used. This leads
to certain issues when the skcipher walk functions are used, e.g.
processing less than block size bytes is not supported by calling
skcipher_walk_done.
The walksize is 2 AES blocks because otherwise for splitted input
or output data, less than blocksize is to be returned in some cases,
which cannot be processed. Another issue was that depending on
possible split of input/output data, just 16 bytes are returned while
less than 16 bytes were remaining, while cipher text stealing
requires 17 bytes or more for processing.
For example, if the input is 60 bytes and the walk is 48, then
processing 48 bytes leads to a return code of -EINVAL for
skcipher_walk_done. Therefor the processed counter is used to
figure out, when the actual cipher text stealing for the remaining
bytes less than blocksize needs to be applied.
Measured with cryptsetup benchmark, this XTS AES implementation is
about 19% faster than the kernels XTS implementation that uses the
hardware ECB AES (ca. 18.6 MiB/s vs. 15.8 MiB/s decryption 256b key).
The implementation was tested with the kernels crypto testmgr against
the kernels generic XTS AES implementation including extended tests.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:08 +01:00
Daniel Kestrel
006fee0dad ltq-deu: update initialisations for hmac algorithms
The processing in the hmac algorithms depends on the status fields:
count, dbn and started. Not all were initialised in the init method
and after finishing the final method. Added missing fields to init
method and call init method after finishing final.
The memsets have the wrong size in the original driver and did not
clear everything and are not necessary. Since no memset is done in
the kernels generic implementation, memsets were removed.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:05 +01:00
Daniel Kestrel
6ade9d1dda ltq-deu: remove compiler warning and shorten locked sections
Removing hash pointer in _hmac_setkey since its not needed and causes
a compiler warning.
Make the spinlock control sections shorter and move initializations
out of the control sections to free the spinlock faster for allowing
other threads to use the hash engine.
Minor improvements for indentation and removal of blanks and blank
lines in some areas.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:23:02 +01:00
Daniel Kestrel
0470b05b56 ltq-deu: fix temp size exceed in hmac algorithms
Exceeding the temp array size was not checked and instead storage not
allocated by the driver was used/overwritten which in most cases
resulted in reboots. This patch implements processing the input to the
hash algorithm in tempsize chunks.
The _hmac_final methods were changed to _hmac_final_impl adding a
parameter that indicates intermediate or final processing. The started
variable was added to the context to indicate, if there is an
intermediate result in the context. For sha1_hmac the variable to store
the intermediate hash was added to the context too.
In order to avoid md5_hmac_final_impl being recursively called if the
padding of the input and the resulting last transform during the hmac
algorighms final processing causes the temp array to overflow and to
make sure that there is at least one block in the temp array when the
_hmac_final for final processing is called, the check for exceeding
the temp array in _hmac_transform was moved before copying the block
and incrementing dbn. dbn needs to be at least 1 at final processing
time to let the hash engine apply the opad operation.
To make the hash engine not apply the hmac algorithms final opad
operation, for intermediate processing the dbn in the control register
is set to a higher value than number of dbns are actually processed.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:22:59 +01:00
Daniel Kestrel
85383b3112 ltq-deu: fix setkey errors and static shared temp for hmac algos
The hmac algorithms state, that keys larger than the key size should be
hashed with the underlying hash algorithms and then those hashes are to
be used as keys. This patch implements this. In order to avoid allocating
a descriptor during setkey, a shash_desc pointer is added to the context.
Another issue for multithreaded callers is the shared temp array.
The temp array is static and as such would be shared among multithreaded
callers, which obviously would neither work nor produce correct results.
The temp array (4k size) is moved to the context and since the size of
the context is limited, it can only be defined as pointer otherwise the
initialisation of the hash algorithm fails.
The allocations and freeing of both the temp and the desc pointer in the
context are done by implementing cra_init and cra_exit functions for
the hmac algorithms.
Also improved indentation in some areas.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:22:57 +01:00
Daniel Kestrel
9cb1875d2f ltq-deu: fix ifxdeu-ctr-rfc3686(aes) not matching generic impl
Error ifxdeu-ctr-rfc3686(aes) (16) doesn't match generic impl (20) occurs
when running the cryptomgr extra tests that compare against the linux
kernels generic implementation.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:22:53 +01:00
Daniel Kestrel
34a3eaf07f ltq-deu: changes for hash multithread callers and md5 endianess
The algorithms sha1, sha1_hmac and md5_hmac all use ENDI=1. The md5
algorithm uses ENDI=0 and the endian_swap methods to reverse the
endianess switch by using user CPU time, which is unnecessary overhead.
Danube and AR9 devices do not set endianess for SHA1, so is done for
MD5.
Furthermore the patch replaces endian_swap with le32_to_cpu for md5 and
md5 hmac algorithms and removes endian_swap for them.
The init functions initialize the algorithm in the hardware. The lock is
not used to write to the control register. If another thread calls
another hash algo before update or final, the result will be wrong.
Therefore move the algorithm init to the lock protected sections in the
transform or final methods.
Setting the hw key for the hmac algorithms is now done from within the
lock protected sections in their final methods. The lock protecting is
removed from the _hmac_setkey_hw functions.
In final for md5 and sha1 the lock section is removed, because all the
work was already done in transform (which is called from final). As such
only copying the hash to the output is required.
MD5 and MD5_HMAC produce 16 byte hashes (4 DWORDS) only, therefor
writing register D5R to the hash output is removed for MD5_HMAC.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:22:50 +01:00
Daniel Kestrel
87a19c9345 ltq-deu: make deu hash lock global and remove md5_hmac_ exports
All hash algorithms use the same base IFX_HASH_CON to access the hash unit.
Parallel threads should not be able to call different hash algorithms and
therefor a global lock is required.
Fixed linker warning, that md5_hmac_init, md5_hmac_update and
md5_hmac_final are static export symbols. The export symbols are not
required, because the functions are exposed using shash_alg structure.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:22:48 +01:00
Daniel Kestrel
536dc6f164 ltq-deu: add aes_ofb and aes_cfb algorithms
The functions ifx_deu_aes_cfg and ifx_deu_aes_ofb have been part of the
driver ever since. But the functions and definitions to make the
algorithms actually usable were missing.
This patch adds the neccessary code for aes_ofb and aes_cfb algorithms.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:22:45 +01:00
Daniel Kestrel
cd01d41c77 ltq-deu: fix cryptomgr test errors for aes
When running cryptomgr tests against the driver, there are several
occurences of different errors for even and uneven splitted data in the
underlying scatterlists for the ctr and ctr_rfc3686 algorithms which are
now fixed.
Fixed error in ctr_rfc3686_aes_decrypt function which was introduced with
the previous commit by using CRYPTO_DIR_ENCRYPT in the decrypt function.

Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
2022-01-06 00:22:42 +01:00