If only AP mode is needed, this is currently the most space-efficient way to
provide support for WPA{2,3}-PSK, 802.11w and 802.11r.
openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin sizes:
4719426 bytes (with wpad-basic-wolfssl)
4457282 bytes (with hostapd-basic-wolfssl)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Ubiquiti EdgeRouter 4 is 4 port Octeon Cavium 7130 powered router.
It has internal power supply and needs c13 power cord.
There are three 10/100/1000 Mbps RJ45/Copper ports and
one 1000 Mbps SFP port connected directly to a SoC.
SoC:
Octeon Cavium 7130 (Cavium 3)
Clocked at 1000Mhz
Memory:
1 GiB (SK hynix H5TQ4G63CFR-RDC × 2)
DDR3, clocked at 533 Mhz (1066Mhz effective)
Flash:
- mtd:
8 MiB (Macronix MX25L6408EMI-12G)
used for uboot/eeprom
- emmc:
4 GiB (SanDisk SDIN7DP2-4G)
used for kernel+rootfs
Leds: 1x for power status (white/blue, controllable)
and 4x for ethernet and sfp ports (no control over them)
Buttons: 1x Reset (from SOC)
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1 (from SoC)
USB: 1x USB3.0 on front panel (from SoC)
MII: 1x QSGMII from SoC is used
PHY: 1x Vitesse VSC8504 of which 4x ports is used
All physical port numbers are properly mapped inside OS and
named by lanX instead of ethX.
There is also special purpose four(4) loopX ports available.
That loopX ports are currently hardcoded by linux kernel
and exact use case of them is currently unknown. We leave them
to the linux kernel and octeon board defaults.
All four (4) physical ports are connected to the same QSGMII.
vsc8504 is used for phys and only 4, 5, 6 and 7 phys are used.
Phy mapping:
- Phy5 is connected to physical eth0 port
- Phy6 is connected to physical eth1 port
- Phy7 is connected to physical eth2 port
- Phy4 is connected to physical eth3 port
Why this device needs external dts:
- faster boot time since need to initialize less device tree nodes.
- to add actual indication with LED about boot/failure/upgrade.
i.e. user could know when to enter failsafe mode or if upgrade is done
- reset button support so user can reset their device in case off failure
- sfp port indication in dmesg with information about sfp module
it also indicates when module inserted or removed
Octeon quirks:
- There is no port status available before it interface brought up
- SFP port can not be tied to actual phy due to octeon-ethernet state
and currently we can only get reports a about SFP state in dmesg
How to flash the firmware:
- copy openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin and
openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar to
USB flash drive that is formatted to vfat/fat32
- connect USB flash drive to edgerouter 4 front USB port
- connect serial cable using front RJ45 port (115200 baud, 8N1)
- connect power to cable to edgerouter 4
- connect terminal to the console to see uboot boot process
- interrupt boot by pressing button(s) on your keyboard to log in to the uboot
- detect usb connected flash drives by typing to the console:
usb start
- after drive is detected load initramfs+kernel to the memory by typing:
fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-4-initramfs-kernel.bin
- after initramfs+kernel is loaded to the memory load it by typing:
bootoctlinux 0 numcores=4 endbootargs mem=0
- boot process should finish and you will be greeted with console after pressing enter
- create directory to mount usb flash drive to by typing:
mkdir /tmp/sda
- mount flash drive to that directory by typing:
mount /dev/sda1 /tmp/sda
- flash firmware to router internal storage by typing:
sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-4-squashfs-sysupgrade.tar
- device will reboot and after it gets up you will have edgerouter 4 running openwrt
Reviewed-by: Johannes Kimmel <fff@bareminimum.eu>
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
adds patch to octeon ethernet driver that lets sgmii interface
device tree node to be disabled and that disabled interface
won't be unnecessarily initialized.
It solves the problem with octeon boards that have 8 sgmii or more ports
initialized but have nothing connected to them.
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
adds patch to octeon ethernet driver that to rename interface
name by label from device tree
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
adds support for vsc8504 phy.
patch have use on 5.4 kernel and has
to be dropped after since phy is supported by
CONFIG_MICROSEMI_PHY on newer LTS kernels.
Tested-by: Johannes Kimmel <fff@bareminimum.eu>
Signed-off-by: Roman Kuzmitskii <damex.pp@icloud.com>
Building gdb failed with CONFIG_BUILD_NLS enabled. Use nls.mk and
add the necessary dependencies for libintl and libiconv.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the default sysupgrade generation procedure provided
by the target. The previously generated images had the rootfs not
aligned to an eraseblock.
Signed-off-by: David Bauer <mail@david-bauer.net>
A lot of devices running OpenWrt x86 arch (32 or 64 bit) are either
"home-made routers" or devices that use PC class OEM components.
This commit enables OEM cards support on those devices by default.
Signed-off-by: Rafał Dzięgiel <rafostar.github@gmail.com>
[reformat commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove MDIO and I2C bitbangig support from the kernel.
These functionalities are currently not used by any board in the target.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes the name for the GMAC clock to gmac_clkin, as this is
the name of the clock provided by the rk3328-clk driver.
Without this commit, the GMAC will not work in TX direction.
Suggested-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
`mt7621_nfc_write_page_hwecc` may be called with `buf=NULL`, but
`mt7621_nfc_check_empty_page` always tries to read it.
That caused Oops:
`Unable to handle kernel paging request at virtual address 00000000`
Fixes: FS#3416
Signed-off-by: Anton Ryzhov <anton@ryzhov.me>
Latest netifd allows us to setup network bridges with implicit vlan
tagging. For this to work, we need to setup several additional uci
sections. This feature is particularly usefull for DSA tupe devices.
Add board.d and uci-defaults support for generating the sections.
Signed-off-by: John Crispin <john@phrozen.org>
Several Ubiquiti WA devices set up &wmac again in their DTS files,
although this is already done in ar9342_ubnt_wa.dtsi.
Fixes: fa3c2676ab ("ath79: Add support for Ubiquiti Nanostation AC")
Fixes: cf5a1abe46 ("ath79: define 2.4GHz radio for nanostation ac loco")
Fixes: 09804da80a ("ath79: define 2.4GHz radio for litebeam ac gen2")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ar9342 Ubiquiti WA devices appear to only have two different
network setups, based on the number of ethernet ports.
Create DTSI files for them to consolidate duplicate definitions.
Signed-off-by: Nick Hainke <vincent@systemli.org>
[rephrase commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In 4.14 the delays were not cleared, so setting "rgmii" as phy-mode
did not affect delays set by the bootloader. With 5.4 kernel the
situation changed and the ethernet interface stopped working.
"rgmii" requires rx and tx delays depending on the hardware circuit
and wiring. The mac or the phy can add these delays.
- "rgmii": delays are controlled by the mac
- "rgmii-id": delays are controlled by the phy
More Information in Linux Kernel Tree:
Documentation/devicetree/bindings/net/ethernet-controller.yaml
"rgmii" should be the preferred mode, which allows the mac layer to
turn off the dealys completely if they are not needed. However, the
delays are not set correctly, which causes the ethernet interface
to be broken. Just taking the ethernetpart from the litebeam ac gen2
will fix the issue.
Explained-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Nick Hainke <vincent@systemli.org>
da9746a libopkg: clean up handling of unresolved dependencies
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
The previous fix of a fix caused yet another problem leading to
`opkg show-upgradable` ending up in an infinite loop.
Fix that.
Fixes: 4a2b1ff7fb ("opkg: fix dependency resolution")
Reported-by: Huangbin Zhan <zhanhb88@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The previous commit broke opkg in a way that it would no longer
include dependencies when installing a package, effectively leading
to broken images and unusable systems.
Fix that by making sure dependencies are still going to be checked.
Also reduce size of struct abstract_pkg as suggested by @jow- while at
it.
Fixes: 1445d333aa ("opkg: bump to git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit introduces a new function `extra_command` to better format
the help text without having to calculate the indentation in every startup
script that wants to add a new command. So far it looks weird and is not
formatted correctly on some startup scripts.
After using the new `extra_command` wrapper the alignement looks correctly.
And if the indentation is not sufficient in the future, this can be
changed in the function extra_command at a central location.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
In kernel commit adf82accc5f5 ("netfilter: x_tables: merge ip and
ipv6 masquerade modules") the config symbols IP_NF_TARGET_MASQUERADE
and IP6_NF_TARGET_MASQUERADE have been demoted to simple backwards-
compat options for NETFILTER_XT_TARGET_MASQUERADE.
In netfilter.mk, this has already been updated in OpenWrt commit
d1592306cc ("netfilter.mk: use CONFIG_NETFILTER_XT_TARGET_MASQUERADE"),
having us use the new config symbol.
However, enabling IP_NF_NAT or IP6_NF_NAT still makes the relevant
legacy options selectable, so we need to disable them in generic
config (and forget about them afterwards).
Since CONFIG_IP_NF_TARGET_MASQUERADE is already present there, this
just adds the missing CONFIG_IP6_NF_TARGET_MASQUERADE.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kernel has removed the symbols CONFIG_NF_NAT_IPV4 and
CONFIG_NF_NAT_IPV6 in favor of CONFIG_NF_NAT in commit
3bf195ae6037 ("netfilter: nat: merge nf_nat_ipv4,6 into nat core").
This drops the obsolete symbol CONFIG_NF_NAT_IPV6 from generic
config-5.4.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This partition isn't normally modified during boot process. Make it
read-only to prevent accidental overwrite.
If needed this can be overriden with installing kmod-mtd-rw; the same
way as for installing modified U-boot.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This partition isn't normally modified during boot process. Make it
read-only to prevent accidental overwrite.
If needed this can be overriden with installing kmod-mtd-rw; the same
way as for installing modified U-boot.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The mount point is "/tmp/boot", the path in the boot partition is
"/boot/grub/upgraded".
Origin of this mark b9c1cf16 ("x86: add preinit hook for bootloader
upgrade")
Fixes 32f675ca ("x86: fix grub-bios-setup fail during sysupgrade")
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140
Reported-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Recent versions (> 5.33) of `file` report liblto_plugin.so as
executable:
$ file liblto_plugin.so
liblto_plugin.so.0.0.0: ELF 64-bit LSB pie executable ...
Which then leads to improper packaging of the plugin, resulting in the
broken compiler:
configure: checking whether the C compiler works
mips-openwrt-linux-musl/bin/ld: liblto_plugin.so: error loading plugin: liblto_plugin.so: invalid ELF header
As the LTO compiler plugin library is incorrectly packaged as SDK
executable:
$ head -1 ~/staging_dir/toolchain...libexec/gcc/.../liblto_plugin.so
#!/usr/bin/env bash
Fix this by filtering out shared libraries from the patching.
Ref: https://bugzilla.redhat.com/show_bug.cgi?id=1296868
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's not possible to compile some applications which are using
`-Werror=missing-include-dirs` compiler flags with the SDK as some
target directories are missing in the SDK tarball:
cc1: error: staging_dir/target/usr/include: No such file or directory [-Werror=missing-include-dirs]
cc1: error: staging_dir/target/include: No such file or directory [-Werror=missing-include-dirs]
Fix this by adding the missing directories in the SDK.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Shallow copies are quite common on CI platforms nowadays, making REBOOT
tag unavailable, thus producing following confusing errors in the build
logs:
fatal: Invalid revision range ee53a240ac902dc83209008a2671e7fdcf55957a..HEAD
fatal: Invalid revision range ee53a240ac902dc83209008a2671e7fdcf55957a..0493d57e04774d47921a7d2014b567455d5dc16b
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The pistachio target uses a MIPS CPU with FPU and OpenWrt uses a
toolchain with hard FPU support. MIPS FPU support needs the FPU
emulation code in the kernel.
Fixes: ac5671f46c ("kernel: remove obsolete kernel version switches for 4.19")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of using the system zlib when the package is selected and using
the internal zlib if it is not selected in OpenWrt, just activate it
always. This should make the package more deterministic.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ARC specific gdb was removed some time ago.
Fixes: 969690b33c ("toolchain/gdb: Don't use gdb-arc")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of patching the tests out, just remove them with a configure
option.
No files were generates in the testsuite and unit-test directories.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gdb 10.1 adds many new features for example gdbserver support for
- ARC GNU/Linux
- RISC-V GNU/Linux
Removed this patch, because similar changes are now integrated upstream:
toolchain/gdb/patches/100-no_extern_inline.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This re-enables offloading features disabled by
commit 9da2b56760 ("ipq40xx: fix ethernet vlan double tagging").
Single-PHY devices use port-based VLANs on the switch, therefore no
S-TAG magic is involved here. Re-enabling these features restores
throughput back to 950 Mbit/s.
Reported-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: David Bauer <mail@david-bauer.net>
The Ubiquiti UniFi AP does not have a AHB connected radio but a PCI one.
Also the EEPROM ist only 0x440 bytes of length.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
The AT803X_PHY kernel config symbol is already enabled target-wide. SO
it does not have to be enabled for individual subtargets.
Signed-off-by: David Bauer <mail@david-bauer.net>
