Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO
enterprise access point with two Gigabit Ethernet ports and PoE
support.
Hardware highlights:
- CPU: QCA9550 SoC at 720MHz
- RAM: 256MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: QCA9550-internal radio
- Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC
- Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY
- Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY
- PoE: input through Ethernet 1 port
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: SGM706 (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- eth1 = label MAC + 1
- radio0 (Wi-Fi 5GHz) = label MAC + 2
- radio1 (Wi-Fi 2.4GHz) = label MAC + 3
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script
"run ramboot". Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile
openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot
be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from
non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP5X30XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap5030dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues
-----------------------
- On initial power-up, the Huawei-modified bootloader suspends both
ethernet PHYs (it sets the "Power Down" bit in the MII control
register). Unfortunately, at the time of the initial port, the kernel
driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume
callback defined which would clear this bit. This makes the PHY unusable
since it remains suspended forever. This is why the backported kernel
patches in this commit are required which add this callback and for
completeness also a suspend callback.
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the CPU_CLK/4 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
[fixed 6.6 backport patch naming]
Signed-off-by: David Bauer <mail@david-bauer.net>
The uboot-envtools can automatically parse the dts 'u-boot,env'
compatible string. So the env config file is now useless.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
- use Makefile.perf to prevent overriding MAKEFLAGS
- fix path to PKG_CONFIG
- link libstdc++ statically (only used for demangling)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware blobs have all different licenses from the different
manufacturers of the binary blobs. This information is contained in the
upstream 'linux-firmware' repositroy.
This commit extends the package handling so that this information can be
added as an additional argument during packages generation.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Key features:
Allwinner H618 SoC (Quad core Cortex-A53)
1/1.5/2/4 GiB LPDDR4 DRAM
1 USB 2.0 type C port (Power + OTG)
1 USB 2.0 host port
1Gbps Ethernet port
Micro-HDMI port
MicroSD slot
Installation:
Write the image to SD Card with dd.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This version supports LPDDR4 DRAM of H618 SoC.
Runtime-tested:
Olimex Olinuxino Micro (A20)
Orange Pi Zero 3 (H618)
Pine64 SoPine (A64)
Tested-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Kernel 6.3 has introduced separate C45 read/write operations, and thus
split them out of the C22 operations completely so the old way of marking
C45 reads and writes via the register value does not work anymore.
This is causing SSDK to fail and find C45 only PHY-s such as Aquantia ones:
[ 22.187877] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 8, phy_id = 0x0 phytype doesn't match
[ 22.209924] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 0, phy_id = 0x0 phytype doesn't match
This in turn causes USXGMII MAC autoneg bit to not get set and then UNIPHY
autoneg will time out, causing the 10G ports not to work:
[ 37.292784] uniphy autoneg time out!
So, lets detect C45 reads and writes by the magic BIT(30) in the register
argument and if so call separate C45 mdiobus read/write functions.
Signed-off-by: Robert Marko <robimarko@gmail.com>
79f8cfa58ee7 ci: add github test workflow
428f40e7984f test commit fixing warnings
63058d1f81a5 ci: enable ujail builds
49ea930a862c utils: add key-value offset support to get_cmdline_val()
ca8c30208d5e inittab: fallback when multiple "console=" is detected
Required for the recent Elecom multiple console commits.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, both CI and local builds of wpa-supplicant will fail with:
/bin/sh: Argument list too long
Its happening as the argument list for mkdir in build.rules is too large
and over the MAX_ARG_STRLEN limit.
It seems that recent introduction of APK compatible version schema has
increased the argument size and thus pushed it over the limit uncovering
the issue.
Fixes: e8725a932e ("treewide: use APK compatible version schema")
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the change in version schema the downloaded files changed, too,
mostly the hash is now prefixed with a tilde `~` instead of a dash `-`.
Since each downloaded archive contains folder with the same name as the
archive, the checksum changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add imx8m support:
- add a cortexa53 subtarget to imx
- move ARCH and KERNELNAME to subtargets
- account for kernel modules that are not used for cortexa53
No device-specific targets or firmware images are created yet but all
imx8m* dtbs will be built.
enabling CONFIG_TARGET_ROOTFS_INITRAMFS results in
openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin which has been
successfully booted on an imx8mm-evk using the following:
u-boot=> tftpboot $fdt_addr_r image-imx8mm-evk.dtb && \
tftpboot $kernel_addr_r openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin && \
booti $kernel_addr_r - $fdt_addr_r
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Alexander reported following:
iwlwifi 0000:00:14.3: Detected crf-id 0x3617, cnv-id 0x20000302 wfpm id 0x80000000
iwlwifi 0000:00:14.3: PCI dev a0f0/0074, rev=0x351, rfid=0x10a100
iwlwifi 0000:00:14.3: Direct firmware load for iwlwifi-QuZ-a0-hr-b0-77.ucode failed with error -2
It seems, that as of the current date, the highest firmware API version
supported by Linux 6.8-rc7 is still 77.
Closes: #14771
Signed-off-by: Petr Štetiar <ynezz@true.cz>
3aa2b6b devices: add device id for MediaTek MT7601U
79a9615 devices: add device id for Realtek RTL8188CU and RTL8188FTV
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without this configuration it is not possible to run the radio using HE160 on channels 149-177.
Fixes: #14906
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
The carl9170_tx_release() function sometimes triggers a fortified-memset
warning in my randconfig builds:
In file included from include/linux/string.h:254,
from drivers/net/wireless/ath/carl9170/tx.c:40:
In function 'fortify_memset_chk',
inlined from 'carl9170_tx_release' at drivers/net/wireless/ath/carl9170/tx.c:283:2,
inlined from 'kref_put' at include/linux/kref.h:65:3,
inlined from 'carl9170_tx_put_skb' at drivers/net/wireless/ath/carl9170/tx.c:342:9:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
Kees previously tried to avoid this by using memset_after(), but it seems
this does not fully address the problem. I noticed that the memset_after()
here is done on a different part of the union (status) than the original
cast was from (rate_driver_data), which may confuse the compiler.
Unfortunately, the memset_after() trick does not work on driver_rates[]
because that is part of an anonymous struct, and I could not get
struct_group() to do this either. Using two separate memset() calls
on the two members does address the warning though.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
enable support for RK35xx in kmod-ata-ahci-platform kernel module
Suggested-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Different from OPKG, APK uses a deterministic version schema which chips
the version into chunks and compares them individually. This enforces a
certain schema which was previously entirely flexible.
- Releases are added at the very and end prefixed with an `r` like
`1.2.3-r3`.
- Hashes are prefixed with a `~` like `1.2.3~abc123`.
- Dates become semantic versions, like `2024.04.01`
- Extra tags are possible like `_git`, `_alpha` and more.
For full details see the APK test list:
https://gitlab.alpinelinux.org/alpine/apk-tools/-/blob/master/test/version.data
Signed-off-by: Paul Spooren <mail@aparcar.org>
Since 6.5 netdev_rx_queue was moved out of netdevice.h so include the new
header since that is where it lives now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update the deprecated license information from GPL-2.0 to GPL-2.0-only
as written in the COPYING file of the linux source tree.
Also add the 'COPYING' file to the PKG_LICENSE_FILES variable.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The lincense information for the packages mac80211 are missing.
This commit adds the missing information.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add support for Xiaomi Redmi AX6S to be used as a second-stage
UBI loader.
The defconfig/env is minimal: Boot fit from UBI. If that failed,
load and boot initramfs image from TFTP.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
PKG_MIRROR_HASH was accidentally generated with already APK-adapted
version string in the filename. That can't work (yet). Regenerate and
hash the file with the currently used version scheme to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
e91ed40 ubus: assume that the service iface can be NULL
4094a3c interface: remove unused peer field
8a0c9db interface: add missing cache cleanup on interface free
3b341f4 add the ability to announce additional hostnames
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure /etc/umdns/ is accessiable for the umdns process if it
exists and umdns is run with umdns.@umdns[0].jail='1'.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
That new version seems to work more stable including mesh.
On version 2.4.0.1-01746 rproc was immediately crashing if mesh was
active.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
a903d3169193 wifi: mt76: mt7921: fix a potential association failure upon resuming
eb0d0ce344f3 wifi: mt76: mt7921: fix suspend issue on MediaTek COB platform
841bf82e9958 wifi: mt76: fix the issue of missing txpwr settings from ch153 to ch177
ce7ccc540168 wifi: mt76: Remove redundant assignment to variable tidno
a238df940d6f wifi: mt76: mt7915: initialize rssi on adding stations
46c7d1849dbd wifi: mt76: replace skb_put with skb_put_zero
b5640b3153c7 wifi: mt76: fix tx packet loss when scanning on DBDC
7b054e5cb3af wifi: mt76: mt7915: fix mcu command format for mt7915 tx stats
3f27a64a8010 wifi: mt76: mt7915: fix bogus Tx/Rx airtime duration values
4f681a8fbc91 wifi: mt76: mt7915: fix HE PHY capabilities IE for station mode
8ede229eb8b5 wifi: mt76: mt7915: only set MT76_MCU_RESET for the main phy
2330781b8c5f wifi: mt76: mt7996: only set MT76_MCU_RESET for the main phy
e5fb6995e7eb wifi: mt76: mt7915: add support for disabling in-band discovery
b4a917417c85 wifi: mt76: mt7915: add mt7986, mt7916 and mt7981 pre-calibration
2135e201e7a9 mt76: mt7915: add fallback in case of missing precal data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Build and package driver for MediaTek PCIe 5G WWAN modem T7xx device
available in Linux 6.1 and 6.6 as kmod-mtk-t7xx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Using := doesn't fly well when including other variables. In fact this
would cause the variable to be empty and break cloning of the git repo.
Fix: "c354c069b3 uci: fix Makefile formatting"
Signed-off-by: Paul Spooren <mail@aparcar.org>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6281 @1GHz
- 128Mb RAM
- 256Mb NAND
- 1x GbE LAN (Marvell 88E1116)
- 1x USB 2.0
- 2x SATA
- PCF8563 RTC
- LM75 sensor
- TC654 PWM fan controller
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b ./u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 netgear_stora-u-boot.kwb
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-netgear_stora-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
The fan is controlled in 3 stages by a script running every minute
from cron, measuring the CPU temperature.
Snippets taken from bodhi <mibodhi@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add a separate bit in struct ieee80211_tx_info to indicate airtime tracked
as broadcast/multicast. This avoids a race condition where airtime from
stations that were just removed wasn't getting subtracted from the total
PHY airtime.
Fixes: 95e633efbd ("mac80211: add AQL support for broadcast/multicast packets")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
drm-amdgpu and drm-radeon require drm-exec and/or drm-suballoc-helper in
6.6, so since we have them packaged separately include them when required.
Fixes: 5b08b56007 ("kernel: modules: video: adapt for kernel 6.6")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linux 6.4 has split out the previously AMDGPU specific suballocation
helper into a generic one and it has its own symbol now.
So, lets package it as a separate helper as AMDGPU still requires it
for 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
