Commit Graph

809 Commits

Author SHA1 Message Date
Sungbo Eo
aabdf6991c ramips: improve Samsung CY-SWR1100 support
This patch does the following:

- rename "devdata" flash partition and make it read-only
- switch from gpio-keys-polled to gpio-keys
- add missing power LED
- set correct PCI ID to compatible string in wifi node
- remove ralink,5ghz property in wifi node
- provide label MAC address

Rename devdata partition to devconf as indicated in the stock firmware
partition table:
00030000-00040000: "devdata"
00040000-00050000: "devconf"

Power LED can be controlled by SoC GPIO. Add it in the dts leds node.

RT3092L supports only bgn mode, so it is unnecessary to disable 5GHz band.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-13 16:03:42 +01:00
David Bauer
b16d76bf40 ramips: correct Netgear WNDR3700v5 button flag
This adjusts the GPIO state flag to ACTIVE_LOW as FCC pictures indicate
the base board is identical to the one of the R6220.

Fixes commit 3459013257 ("ramips: correct R6220 button flag")

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-10 20:57:16 +01:00
David Bauer
3459013257 ramips: correct R6220 button flag
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.

The GPIO status reads the following for no buttons pressed:

root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7   (                    |wps                 ) in  hi
gpio-8   (                    |wifi                ) in  hi
gpio-14  (                    |reset               ) in  hi

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-09 19:15:40 +01:00
Adrian Schmutzler
f098c612b6 ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3
This moves shared code of the named devices into a common DTSI.

Remove setting status="okay" for &gpio0 as it's not disabled in
mt7620a.dtsi.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:17:31 +01:00
Frederik Noe-Sdun
4a904b8b76 ramips: increase max SPI frequency to 50 MHz for EX3700/EX6130
Based on Macronix MX25L3205DM2I datasheet this is maximum
supported speed.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, improved commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:17:25 +01:00
Frederik Noe-Sdun
0cbd2c74d0 ramips: add support for Netgear EX6130
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the
device's web interface or via nmrpflash.

The device seems to use base PCB as EX3700/EX3800,
but supporting AC1200 using MT7612E.

MAC adresses:
5.0 GHz  0x8004  *:9a
2.4 GHz  0x4     *:9b
lan      0x28    *:9b
wan      0x2e    *:9c

Since this is a one-port device, although wan MAC address is
set in flash, it is not used in OpenWrt setup.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, extended commit message, tiny DTS style fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:16:14 +01:00
Adrian Schmutzler
a921945773 ramips: rename keys node formerly named button
For some devices, the keys node is named "button". Change name to
match the rest of the target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-07 17:13:18 +01:00
Adrian Schmutzler
c7842ceaaa ramips: reorganize DTSI files for Netgear R devices
This reorganizes DTSI files for the Netgear R devices in mt7621
(and the WNDR3700 v5). It creates a common DTSI for all R (sercomm)
devices and distributes the remaining code in r6220.dtsi to R6220
and WNDR3700 v5.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:43:04 +01:00
Sungbo Eo
62b1559b56 ramips: improve support for WeVO 11AC NAS and W2914NS v2
- remove WAN port index
- load WAN MAC address directly from the flash
- provide label MAC address
- increase flash's SPI frequency to 80MHz
- add mt76 led nodes to make WiFi LEDs work
- drop unnecessary pinmux groups

The factory partition scheme for MAC addresses (verified on both devices):
0x4   : WiFi 2.4GHz (label_mac-9)
0x28  : unused
0x2e  : WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-5)
0xe000: LAN (label_mac-1)
0xe006: unused

By improving flash speed,
`time dd if=/dev/mtdblock3 of=/dev/null bs=64k`
has been reduced from 14.51s to 3.11s.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-06 14:31:32 +01:00
Sungbo Eo
763914ef1b ramips: improve netis WF-2881 support
This patch does the following:

1. remove u-boot-env partition
   Stock bootloader saves env variables at 0x80000 in flash,
   and there is nothing stored at 0x30000.
   By merging the partition "u-boot-env" with "u-boot",
   the partition table becomes the same as used in stock firmware:
   00000000-00080000: "Bootloader"
   00080000-00100000: "Config"
   00100000-00140000: "Factory"
   00140000-07f80000: "Kernel"

2. fix LAN/WAN MAC addresses and provide label MAC address
   Ethernet MAC addresses are stored in factory partition at:
   0xe000: LAN (label_mac)
   0xe006: WAN (label_mac+1)

3. fix LAN port order
   WF-2881 LAN ports are in reverse order of switch ports.

4. fix WiFi LEDs
   mt76 led nodes are added to make WiFi LEDs work.
   On top of this, mt76 node names are changed to more generic ones,
   and compatible strings are also added.

5. fix pinmux groups
   uart3 and uart2 pins are used as button and led, but jtag pins are not.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-06 00:27:55 +01:00
Sungbo Eo
6ea5f7d44c ramips: fix MTK_SOC for RT3662 devices
rt3883.mk contains both RT3662 and RT3883 device profiles, but commit
6a104ac772 set MTK_SOC to rt3883 for all devices. This patch fixes it,
and renames dts files accordingly. And SoC compatible strings are also
appended in the dts.

Fixes: 6a104ac772 ("ramips/rt288x,rt3883: Name DTS files based on scheme")

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-04 15:22:54 +01:00
Kristian Evensen
5f108bbc58 ramips: add support for ZBT WE1026-H
This commit adds support for the ZBT WE1026-H, an outdoor AP with
support for adding an internal LTE modem. The detailed specs are:

* CPU: MT7620A
* 2x 10/100Mbps Ethernet (LAN port has passive PoE support).
* 16/32 MB Flash.
* 128/256 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slot (only USB2.0 bus).
* 1x SIM slot (standard size).
* 1x 2.4Ghz WIFI (rt2800).
* 1x button.
* 6x LEDS (4 GPIO-controlled).
* 1x micro-SD reader.

The following have been tested and working:
- Ethernet switch
- Wifi
- Mini-PCIe slot + SIM slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or ito recover the router,
you can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.

Notes:

* When binding the USB LED to a usbport, the LED is switched on all the
time due to the presence of an internal hub. Thus, it does not really
signal any USB-information.

* I only have the 32MB version and have only added support for this
device. However, the files are structured so that adding support for the
16MB version should be easy.

* Only the LAN port is accessible from the outside of the casing and LEDs
are not visible.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[rebased onto base-files split, minor style fixes, removed use of
USB led as power LED]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 15:10:22 +01:00
Kristian Evensen
a033f14fe9 ramips: update ZBT WE1026 DTS-files
This commit makes the following changes to the WE1026 DTS-files:

* The parts that are unique to the -5G-version (LED and 5GHz wifi)
are moved to a separate file, so that WE1026.dtsi can be referenced also
by the DTS for the -H version.
* Use the generic "flash"-name for the spi-nor node.
* Add label MAC.

All changes have been tested on the WE1026-5G-16M and work fine. I.e.,
the device works as before the DTS-changes.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Mathias Kresin <dev@kresin.me>
Acked-by: Alex Maclean <monkeh@monkeh.net>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
[minor style fixes, rebased onto base-files split, remove obsolete
gpio-keys comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 15:10:14 +01:00
Adrian Schmutzler
0975c35b83 ramips: add newline for ASUS RT-ACx5P DTSes
Those files are missing the newline at the end.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 00:23:35 +01:00
Paul Fertser
522d5ff428 ramips: add support for Xiaomi Mi Wi-Fi Router 3G v2
- CMIIT ID: 2019AP2581
- SoC:      MediaTek MT7621
- Flash:    16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM:      128MiB DDR3 (ESMT M15T1G1664A)
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0:    MT7603E 2.4GHz 802.11b/g/n
- WIFI1:    MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable "power" LED (two-coloured, yellow/blue)
            Non-programmable "internet" LED (shows WAN activity)
- Buttons:  Reset

INSTALLATION:

Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.

With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.

For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).

Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".

[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-10-27 12:25:56 +01:00
Adrian Schmutzler
1abb473cea ramips: remove phy0tpt trigger from RT-AC65P/RT-AC85P power LED
This patch removes a phy0tpt trigger from the power LED, which
seems to have been added by mistake.

WiFi LEDs using phy0radio and phy1radio triggers are present and
used correctly.

Cc: Birger Koblitz <mail@birger-koblitz.de>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 12:13:48 +01:00
Adrian Schmutzler
b6d53f1d02 ramips: remove redundant mtd-eeprom in mt76x8 DTS files
In mt7628an.dtsi, calibration data for wmac is already defined:
mediatek,mtd-eeprom = <&factory 0x0>;

Thus, this patch removes redundant entries of this property in
derived DTS files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 12:13:06 +01:00
Adrian Schmutzler
547720fb48 ramips: remove redundant mtd-mac-address for WiFi
When caldata locations are defined with mediatek,mtd-eeprom the
MAC address is automatically read from offset +4. Thus, specifying
that location explicitly is redundant.

This patch removes those redundant definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 12:12:50 +01:00
Gabor Varga
7c5f712e4f ramips: add support for Asus RT-AC65P
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.

On both routers the installation can be done also via SSH:

Note: The user/password for SSH is identical with the one used in the
Web-interface.

1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
 > scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
 > ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
 > mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
 > reboot

Changelog:

v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release

Signed-off-by: Gabor Varga <vargagab@gmail.com>
2019-10-24 22:58:02 +02:00
Adrian Schmutzler
4408723d42 ramips: remove RAM size from device name for UniElec devices
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.

Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:27:30 +02:00
Adrian Schmutzler
556ff09875 ramips/mt762x: convert devices to interrupt-driven gpio-keys
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.

While at it, add/remove newlines in keys and leds node where
necessary.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:19:32 +02:00
Adrian Schmutzler
e816c50993 ramips: fix whitespace issues in DTS files
This is the result of grepping/searching for several common
whitespace issues like double empty lines, leading spaces, etc.

This patch fixes them for the ramips target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:10:47 +02:00
Adrian Schmutzler
d1072096f4 ramips: fix WiFi MAC addresses for D-Link DIR-810L
So far, WiFi MAC addresses for this device have been set up from
caldata. However, this returns values which do not look like MAC
addresses. They also do not match stock firmware:

wlan0 (5.0): 00:11:22:00:17:D0 from 0x8004
wlan1 (2.4): 00:11:22:00:17:CD from 0x4 (and 0x2e)

It looks like the only valid MAC address on this device is at 0x28.

So, this patch changes setup to calculate addresses based on the
value at 0x28:

lan: *:0A (flash, label)
wan: *:0B (flash + 1)
wifi2: *:0A (flash)
wifi5: *:0C (flash + 2)

Thanks to Roger Pueyo Centelles <roger.pueyo@guifi.net> for
investigating this on his devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-15 23:31:13 +02:00
Davide Fioravanti
67d019ac94 ramips: enable LED VCC for Asus RT-AC51U
Previously only the power LED was working.
With this patch all leds except 5GHz are working.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[rephrased commit title, drop status property]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-06 21:28:49 +02:00
Adrian Schmutzler
400e56d22c ramips: apply consistent device name/compatible to ZBT-WE1026-5G
All Zbtlink ramips devices except the ZBT-WE1026-5G include the
zbt-/ZBT- prefix in their model name.

This changes ZBT-WE1026-5G to also follow that scheme.

The patch moves some block to keep alphatical order.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:08:20 +02:00
Adrian Schmutzler
b376818f97 ramips: harmonize device vendor Zbtlink
Spelling of Zbtlink varies across image definitions and DTS files.

This patch uses Zbtlink consistently and also updates the model
in DTS files to contain the vendor in all cases.

This patch is cosmetical, as there should be no dependencies on
device model name in ramips anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:08:20 +02:00
INAGAKI Hiroshi
12ab6ef5c3 ramips: add support for I-O DATA WNPR2600G
I-O DATA WNPR2600G is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Specification:

- SoC           : MediaTek MT7621A
- RAM           : DDR3 128 MiB
- Flash         : SPI-NOR 16 MiB
- WLAN          : 2.4/5 GHz 4T4R
  - 2.4 GHz     : MediaTek MT7615
  - 5 GHz       : MediaTek MT7615
- Ethernet      : 10/100/1000 Mbps
  - Switch      : MT7530 (SoC)
- LED/keys      : 4x/3x (2x buttons, 1x slide-switch)
- UART          : through-hole on PCB
  - J1: Vcc, RX, GND, TX from SoC side
  - 57600n8

Flash instruction using factory image:

1. Boot WNPR2600G normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-09-25 14:44:36 +08:00
Sungbo Eo
b7ec6659a1 ramips: add support for ipTIME A3
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-09-25 14:44:36 +08:00
Qi Jiang
93b6cc97ca ramips: add support for XiaoYu XY-C5
Hardware:
SoC:      MT7621A
Flash:    32 MiB
RAM:      512 MiB
Ethernet: built-in switch
USB:      1x USB3.0
SATA:     ASM1060, 1 SATA port

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.173.22
2. Download *-sysupgrade.bin image and rename it to firmware.img
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Turn on router,press the reset button and wait ~15 seconds
6. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
7. Wait ~3 minutes to complete recovery.

Signed-off-by: Qi Jiang <rushx@live.cn>
[squash commits, add label-mac-device, fix sign-off style]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-09-25 14:44:36 +08:00
Nick Briggs
3df3bb0dae ramips: add support for EnGenius ESR600
The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit
Ethernet switch, a gigabit Ethernet WAN port and a USB port.

Specification:

- Bootloader:	U-Boot
- SoC:		MediaTek MT7620A (600 MHz)
- Flash:	16MB, Macronix MX25L12845E
- RAM:		64MB, Nanya NT5TU32M16DG-AC
- Serial:	115200 baud, no header, 3.3V
  		J2: Vcc (arrow), Gnd, Tx, Rx
- USB:		USB 2, 5V
- Ethernet:	5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327
- WiFi0:	5 GHz 802.11 b/g/n Ralink RT5592N
  		300 Mb/s, 2T2R
- WiFi1:	2.4 GHz 802.11 b/g/n integrated
  		300 Mb/s, 2T2R
- Antennas:	2 per radio, internal
- LEDs:		1 programmable power (amber)
  		2 programable radio (blue)
		1 programable WPS-5G (blue)
		1 non-programable WAN activity (blue)
		1 unconfigured WPS-2.4G (amber)
- Buttons:	GPIO: Reset, WPS

Installation:

Use the OEM web interface to install the ...-factory.dlf image.
Use the OpenWRT ...-sysupgrade.bin image for future upgrades.

The J2 serial port can be accessed either by soldering in a header,
standard 0.1" spacing, or by using pogo-pins against the back side.

As configured by the OEM, the U-Boot boot delay is short, however quickly
typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP"
prompt.  The TFTP client is configured by default with
     client:   192.168.99.9
     server:   192.168.99.8
     filename: uImageESR600
It will load an OpenWRT initramfs kernel with this method.

Known issues:

1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational.
LAN1 and LAN2 do not appear to power up. This issue is also present
in the Lava LR25G001.

2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED,
is not configured in the Device Tree specification.

3) The blue WAN activity LED is not configured in the Device Tree
specification as this causes the AR8327 switch to fail to initialize.

Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com>
[merge conflict in 02_network]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Daniel Danzberger
10c5d3dd5f ramips: mt7621: Add new device AsiaRF AP7621-NV1
SoC:    Mediatek MT7621A
CPU:    4x 880Mhz
Cache:  32 KB I-Cache and 32 KB D-Cach
        256 KB L2 Cache (shared by Dual-Core)
RAM:    DDR3 512MB 16bits BUS
FLASH:  16MB
Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN)
POE:    (1x PD, 2x PSE)
USB:    1x 3.0
PCI:    3x Mini PCIe (3 USB2.0 + 2 x UIM interface)
GPS:    Quectel L70B
SIM:    2 Slots
BTN:    Reset
LED:    - Power
        - Ethernet
        - Wifi
        - USB
UART:  UART is present as Pads with throughholes on the PCB.
       They are located on left side.
       3.3V - RX - GND - TX / 57600-8N1
       3.3V is the square pad

Installation
------------
The stock image is a modified openwrt and can be overflashed via sysupgrade -F

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
[merge conflict in mt7621.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Birger Koblitz
fde8e2e035 ramips: add support for Asus RT-AC85P
SoC:	MediaTek MT7621AT dual-core @ 880MHz
RAM:	256M (Winbond W632GG6KB-1)
FLASH:	128MB (Macronix MX30LF1G18AC-TI)
WiFi:	- 2.4GHz MediaTek MT7615N bgn
	- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x USB 3.1 (Gen 1)
BTN:	Reset, WPS
LED:	- Power (blue)
	- 5Ghz (blue)
	- 2.4GHz (blue)
	- Internet (blue)
	- 4x LAN (blue)
	(LAN/WAN leds are not controllable by GPIOs)
UART: 	UART is present as Pads marked J4 on the PCB.
	3.3V - TX - RX - GND / 57600-8N1
	3.3V is the square pad
MAC:	The MAC address on the router-label matches the MAC of
	the 2.4 GHz WiFi.
	LAN and WAN MAC are identical: MAC_LABEL+4
	5 GHz WiFi MAC: also MAC_LABEL+4

Installation
------------
Via U-Boot tftpd:
Switch on device, within 2s press reset button and keep pressed
until power LED starts blinking slowly.
Upload factory image via tftp put, the router's ip is 192.168.1.1
and expects the client on 192.168.1.75.

The images also work on the Asus RT-AC65P models as tested by Gabor.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Gabor Varga <vargagab@gmail.com>
[fixed Asus -> ASUS in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Birger Koblitz
f285e8634c ramips: add support for Edimax RG21S
SoC:	MediaTek MT7621AT dual-core @ 880MHz
RAM:	256M (Nanya NT5CC128M)
FLASH:	16MB (Macronix MX25L12835F)
WiFi:	- 2.4GHz MediaTek MT7615N bgn
	- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB:	No
BTN:	Reset, WPS
LED:	4 red LEDs, indistinguishable when casing closed
UART: 	UART is present as Pads marked J1 on the PCB.
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the OEM web-interface
(by default:http://192.168.1.1)
The sysupgrade image can be installed via TFTP from
the U-Boot bootloader. Connect ethernet port 2.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[flash node rename, EDIMAX -> Edimax, complete device model name]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Adrian Schmutzler
7140394903 ramips: provide label MAC address
This patch adds the label MAC address for several devices in
ramips.

Some devices require setting the MAC address in 02_network:

For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- cudy,wr1000
- dlink,dir-615-d
- dlink,dir-615-h1
- dlink,dir-860l-b1
- glinet,gl-mt300a
- glinet,gl-mt300n
- glinet,gl-mt750
- vocore,vocore2
- vocore,vocore2-lite
- zbtlink,zbt-we1326
- zbtlink,zbt-wg3526

For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- dlink,dir-510l
- dlink,dwr-116-a1
- dlink,dwr-118-a1
- dlink,dwr-118-a2
- dlink,dwr-921-c1
- dlink,dwr-922-e2
- all hiwifi devices
- lava,lr-25g001
- xiaomi,mir3p

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-19 23:43:27 +02:00
Daniel Golle
6364e03736 ramips: only add spidev node in for WrtNode2R (and not for 2P)
Only the 2R version got the STM32 uC connected as 2nd SPI device.
Hence move the spidev node from mt7628an_wrtnode_wrtnode2.dtsi to
mt7628an_wrtnode_wrtnode2r.dts.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-09-15 20:18:39 +02:00
Roger Pueyo Centelles
e667d6f46b ramips: enable external amplifier for D-Link DIR-810L
The 2.4 GHz radio had very poor signal reception (-89 dBm for an AP
sitting 5 m away). By enabling the external amplifier, received signal
has improved to -50 dBm for the same AP.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-09-10 22:43:37 +08:00
Adrian Schmutzler
869a0183b9 ramips: fix MAC address setup for Newifi Y1 and Y1S
So far, MAC address setup for those devices has been using local
addresses although additional MAC addresses are available on flash.

On device, we found the following situation:
position   Y1     Y1S
0x4        *:d4   *:e4
0x8004     *:d6   *:e8
0x28       *:d4   *:e4
0x2e       *:d7   *:eb

Since 0x4 and 0x28 yield the same address, the former was set for
&ethernet in DTS. However, the typical location on this
architecture is 0x28, so this patch changes that.

For further setup in 02_network, the local bit for lan_mac is
removed, so the address from &ethernet is used at all. For wan_mac,
instead of calculating an address with local bit set, this patch
exploits the previously unused address in 0x2e.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-07 21:41:44 +08:00
Adrian Schmutzler
6640e1c368 ramips: clean and improve MAC address setup in 02_network
This patch removes unnecessary MAC address setup statements in
ramips' 02_network by doing several optimizations:

1. For the following devices, lan_mac was set up with
   mtd_get_mac_binary although the same address was set in DTS.
   The lan_mac statement is removed in 02_network, but
   wan_mac is kept:
   - mercury,mac1200r-v2
   - phicomm,k2g
   - skylab,skw92a
   - wiznet,wizfi630a

2. For the following devices, wan_mac was set up with
   mtd_get_mac_binary although the same address was set in DTS.
   The wan_mac statement is removed in 02_network, no
   lan_mac is present:
   - buffalo,whr-g300n
   - glinet,gl-mt300n-v2
   - zyxel,keenetic-start

3. For the following device, lan_mac and wan_mac were set up
   with mtd_get_mac_binary to the same address as set in DTS.
   Both statements are removed in 02_network:
   - buffalo,whr-600d

4. For some devices, it was possible to move setup from 02_network
   to DTS by introducing previously missing mtd_mac_address:
   - buffalo,whr-1166d
   - buffalo,whr-300hp2
   - buffalo,wsr-600dhp
   - ohyeah,oy-0001
   - planex,vr500

5. For one device, mtd_mac_address was just wrong and overwritten
   by 02_network. Put the correct value in DTS and remove redundant
   statement in 02_network:
   - asus,rt-ac57u

6. For one device, MAC address defined in DTS is exchanged together
   with lan_mac/wan_mac setup in 02_network, so that cases in
   02_network can be merged:
   - phicomm,k2p

For some devices, an empty case has to be used to prevent them
from falling into the default case and have
WAN address = eth0 address + 1 set to them.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-07 21:41:44 +08:00
Chuanhong Guo
7a21c85f70 ramips: improve support for Xiaomi Miwifi Nano
This patch does the following things:
1. mark u-boot-env writable
2. add bootcount support
   Currently, u-boot has a flag_boot_success env variable to reset.
   Also reset it in our firmware to follow the behavior in vendor's
   firmware.
3. disable usb support
   This router doesn't have usb port at all.
4. increase spi clock to 40MHz
5. fix pinmux groups

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-09-04 19:26:01 +08:00
Christoph Krapp
6cea9688af ramips: add support for Netgear R6260 and R6850
As Netgear uses the same image for R6260, R6350 & R6850
we can merge device tree files and generate separate
images for each device.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add missing WiFi compatible string, fix network
configuration]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
Christoph Krapp
9861fa7aba ramips: add mt7615e support to Netgear R6350
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-08-31 10:31:00 +02:00
David Bauer
fa46c9b208 ramips: use phy trigger for various Netgear boards
This commit switches the default trigger for the WiFi LED from a netdev
trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED
to work, even when the wireless interface is not named "wlan0" without
modifiying the LED settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
Zhenjian Zhang
fb3574f123 ramips: add support for ADSLR G7
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N

Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.

Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
[fix mac location]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-08-24 08:55:33 +08:00
Sungbo Eo
2678ba9093 ramips: add support for ipTIME A604M
ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 5x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-08-17 23:52:34 +08:00
Felix Fietkau
7ec092e641 Revert faulty tree push
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-08-12 12:27:06 +02:00
Felix Fietkau
085141dc5b ramips: add preliminary support for WIO ONE
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-08-12 11:43:39 +02:00
Felix Fietkau
b1db6d0539 ramips: add preliminary support for SGE AP-MTKH7-0006 developer board
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-08-12 11:43:39 +02:00
Davide Fioravanti
0891358e4b ramips: fix lan and wan mac addresses for Cudy WR1000
Lan and Wan addresses are swapped compared to the original firmware.
This patch fixes this problem

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2019-08-11 23:16:03 +02:00
Adrian Schmutzler
da0de5e007 ramips: fix LED labels not updated during device name changes
In commit d93969a13a ("ramips: Improve compatible for TP-Link
Archer devices") and subsequent ones, names of several devices
in ramips have been changed.
Since LED names are frequently invoked by $boardname, this has
broken LED setup in 01_leds, as $boardname and prefix in DTS
do not match anymore.

This patch updates device name prefixes for LEDs in DTS files,
and provides a migration script.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-10 00:32:28 +02:00
Ozgur Can Leonard
d7c082ba4f ramips: add kmod-mt7615e to Xiaomi Mi Router 3 Pro images
Now that the mt76/mt7615e driver is in Openwrt, might as well use it.

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
2019-08-10 00:32:28 +02:00