Replace pending 730-net-phy-at803x-fix-feature-detection.patch with
upstream version and move it to backport.
Refresh other related patch while moving it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upload proposed refreshed patches if the check fails.
This should help devs refresh the patches if they don't have access to a
buildroot.
Devs should ALWAYS refresh the patches before submitting and merging
commits.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch needs to be refreshed to apply cleanly.
Fixes: 998b973157 ("kernel: net: phy: realtek: improve RealTek 2.5G PHY driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: ESMT M15T4G16256A 512MB
Ethernet (Max Speed):
XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan
XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
WiFi:
XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R)
XDR6086/XDR6088:
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 4A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[Add uboot build, fit and sysupgrade support, fix RealTek PHYs]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build
for replacement loader for both TL-XDR6086 and TL-XDR6088. The only
difference at U-Boot level is the different filename requested via
TFTP, matching the corresponding OpenWrt build artifacts for each
device.
The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088
except for the wireless part. Also create a uboot for the TP-Link
TL-XDR4288.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[rebase to uboot 23.04, correct led and button]
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* use interface mode switching only when operating in C45 mode
Linux prevents switching the interface mode when using C22 MDIO,
hence use rate-adapter mode in case the PHY controlled via C22.
* use phy_read_paged where appropriate
* use existing generic inline functions to handle 10GbE advertisements
instead of redundantly defining register macros in realtek.c which
are not actually vendor-specific.
* make sure 10GbE advertisement is valid, preventing false-positive
warning "Downshift occurred from negotiated speed 2.5Gbps to actual
speed 1Gbps, check cabling!" with some link-partners using 1G mode.
* Support Link Down Power Saving Mode (ALDPS)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of use mac-address-ascii in nvmem_get_mac_address
function, move it into of_get_mac_addr_nvmem function to
support more devices.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The Config partition of some machines is special, and the openwrt script
cannot read the protest_lan_mac correctly. This problem can be solved by
reading the mac address (ascii) in dts.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix the network configuration according to the device tree.
Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Due to us keeping a patch around for years and never proposing it to
squashfs4 repository, we resulted in having the same squashfs4 version
but with different supported options. (openwrt patched -- upstream)
To workaround this problem, a non-standard option was required.
To not have surprise on tool bump, backport the patch and add the new
config option required to enable these extended non-standard options.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
U-Boot commit ea6fdc13595 ("dm: button: add support for linux_code in
button-gpio.c driver") makes it mandatory to specify linux,code for all
buttons. As that broke handling of the reset button in U-Boot with the
update to U-Boot 2023.04, add linux,code for all butons.
Reported-by: @DragonBluep
Fixes: 50f7c5af4a ("uboot-mediatek: update to v2023.04")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
According to SinoVoip up to 3A @ 3.3V are available for both
SFP modules together. Raise energy limit from 1W (default) to 3W,
however, be aware that using modules consuming more than 1W will
require active cooling!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
qrtr/ns.ko is now merged into qrtr/qrtr.ko, so drop the individual module packaging.
Fixes: f4989239cc ("kernel: bump 5.15 to 5.15.107")
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, mt7621/dap-x1860
upstream PR 408 improvements:
-Fix AMSDU packets unused
-Removed the ASMDU packets queue
-Add more info in the iw tool
-fix is_hw_crypto_enabled
-Optimization AMPDU_TX_OPERATIONAL (avoid a spinlock)
change to wongsyrone mod
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
`bzip2` is the standard executable for bzip2 compression
this includes development includes and both static and shared libs
(libbz2) which can be used by other packages
the initramfs generator offers the BZIP2 option but there was no
executable to support it, and worked only via side effect of having a
system-installed version of bzip2, which could be less predictable
Signed-off-by: Tony Butler <spudz76@gmail.com>
[ remove unintended change ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 394d7134ec.
The commit has unintentded change that cause compilation error with SDK
or LZO compression.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
QCA has finally sent a proper fixup for the 160MHz regression upstream,
so lets use the pending fix which also properly sets center frequency 2
in case 80+80 MHz is used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Requires: tools/libdeflate
fix consistency of executable to use
`$(STAGING_DIR_HOST)/bin/libdeflate-gzip`, and not system-installed ones
from the usual environment `PATH`;
this affects option `CONFIG_KERNEL_INITRAMFS_COMPRESSION_GZIP`
this may have worked in the past but only via side effect of having the
binaries on the host system (and whatever unpredictable version or
patchset those might be), and did not use the improved but totally
compatible libdeflate-gzip
Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Signed-off-by: Tony Butler <spudz76@gmail.com>
Requires: tools/bzip2
fix consistency of executable to use `$(STAGING_DIR_HOST)/bin/bzip2`, and
not system-installed ones from the usual environment `PATH`;
this affects option `CONFIG_KERNEL_INITRAMFS_COMPRESSION_BZIP2`
this may have worked in the past but only via side effect of having the
binaries on the host system (and whatever unpredictable version or
patchset those might be)
Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Signed-off-by: Tony Butler <spudz76@gmail.com>
`bzip2` is the standard executable for bzip2 compression
this includes development includes and both static and shared libs
(libbz2) which can be used by other packages
the initramfs generator offers the BZIP2 option but there was no
executable to support it, and worked only via side effect of having a
system-installed version of bzip2, which could be less predictable
Signed-off-by: Tony Butler <spudz76@gmail.com>
Instead of erasing the entire NAND partition holding the kernel during
every system upgrade and then flashing a Yaffs file system image
prepared using kernel2minor (not accounting for bad blocks in the
process), use the Yafut utility to replace the kernel executable on
MikroTik NAND devices, preserving the existing Yaffs file system
(including bad block information) on the partition holding the kernel.
Add Yafut to DEFAULT_PACKAGES for the ath79/mikrotik target, so that the
tool is included in the initramfs images created when building for
multiple profiles. However, exclude Yafut from the images built for
MikroTik devices with NOR flash as the tool is currently only meant to
be used on devices with NAND flash.
As this addresses the concerns for MikroTik NAND devices discussed in
commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images"),
re-enable building images for these devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images")
disabled building images for MikroTik devices with NAND flash due to a
less than satisfactory method used for updating the kernel on those
devices back then.
To address the problem, add support for updating the kernel on MikroTik
devices with NAND flash using a new tool, Yafut, which enables copying
files from/to Yaffs file systems even if the kernel does not have native
support for the Yaffs file system compiled in. Instead of erasing the
entire NAND partition holding the kernel during every system upgrade
(which is what the previously-used approach employing kernel2minor
involved), Yafut preserves the Yaffs filesystem present on that
partition and only replaces the kernel executable. This allows bad
block information to be preserved across sysupgrade runs and also
enables wear leveling on the NAND partition holding the kernel. Yafut
does not rely on kernel2minor in any way and intends to eventually
supersede the latter for NAND devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
MEMREAD is a new ioctl for MTD character devices that was first included
in Linux 6.1. It allows userspace applications to use the Linux
kernel's OOB autoplacement mechanism while reading data from NAND
devices. The Yafut tool needs this ioctl to do its job.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
The ramdisk used by sysupgrade on MikroTik devices currently includes
U-Boot fw_* files that are not necessary for performing a system upgrade
on that platform. The relevant lines were added to
target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh by commit
a66eee6336 ("ath79: add mikrotik subtarget"), likely because they also
existed in target/linux/ath79/nand/base-files/lib/upgrade/platform.sh,
where the platform_do_upgrade_mikrotik_nand() function moved by commit
a66eee6336 originally lived. However, these lines were added to
target/linux/ath79/nand/base-files/lib/upgrade/platform.sh by commit
55e6c903ae ("ath79: GL-AR300M: provide NAND support; increase to 4 MB
kernel"), which is not related to MikroTik devices in any way.
Remove the code adding unused U-Boot fw_* files to the ramdisk used by
sysupgrade on MikroTik devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Alter the Aruba AP-105 image generation process so OpenWrt can be loaded
with the vendor Aruba APBoot.
This works by prepending the OpenWrt LZMA loader to the uImage and
jumping directly to the loader. Aruba does not offer bootm on these
boards.
This approach keeps compatibility to devices which had their U-Boot
replaced. Both bootloaders can boot the same image.
The same modification is most likely also possible for the Aruba AP-175.
With this patch, new installations do not require replacing the
bootloader and can be performed from the serial console without opening
the case.
Installation
------------
1. Attach to the serial console of the AP-105.
Interrupt autoboot and change the U-Boot env.
$ setenv apb_rb_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66;
netget 0x84000000 ap105.bin; go 0x84000040"
$ setenv apb_fb_openwrt "cp.b 0xbf040000 0x84000000 0x10000;
go 0x84000040"
$ setenv bootcmd "run apb_fb_openwrt"
$ saveenv
2. Load the OpenWrt initramfs image on the device using TFTP.
Place the initramfs image as "ap105.bin" in the TFTP server
root directory, connect it to the AP and make the server reachable
at 192.168.1.66/24.
$ run apb_rb_openwrt
3. Once OpenWrt booted, transfer the sysupgrade image to the device
using scp and use sysupgrade to install the firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
In addition to standardizing LED names to match the rest of the systems, this
commit fixes a possibly erroneous pinout for LEDs in Comfast CF-E314N v2.
In particular, rssimediumhigh and rssihigh are moved from pins 13 and 14 to
14 and 16 respectively. In addition to working on a test device, this pinout
better matches the one set out in the prototype support patch for the device
in Github PR #1873.
Signed-off-by: Mark Onstid <turretkeeper@mail.com>
RA75 has 5 physical LEDs under 2 indicators, mixed with light pipes:
Indicator "System":
GPIO0: blue
GPIO2: amber
Indicator "Signal":
GPIO44: blue
GPIO37: amber
GPIO46: red
All except GPIO46 were already added by Jo Deisenhofer. GPIO46 is used for UART1 by
default, so it needs additional pin control change in devicetree to be operational.
Verified on my RA75.
Signed-off-by: Oleksandr Zharov <alex.zeed@gmail.com>
Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as
the board design is pretty much the already updated AP-303.
Run-tested on the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Import commit "ubi: Fix failure attaching when vid_hdr offset equals to
(sub)page size" which did not yet make it to stable upstream Linux trees.
Fixes: #12232Fixes: #12339
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
