Copy from the previously mapped block (in case it was remapped already)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 7d1e2be1605eda85e1a607a3d3ddefed1b961d3d)
Used by the mapping implementation to indicate that no backing block is
available
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit b4c7f8c5f7a2dab76fe90849e112c6bd8f80ab19)
Keep a separate source file per variant
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 601c7b4adb0f91005a8755bf9575c68ac623cc33)
Everywhere else the device is referred to as WS-AP3805i,
only the model name wrongly only said AP3805i.
Signed-off-by: Tom Herbers <mail@tomherbers.de>
(cherry picked from commit 7d6032f310058d7e9b96d7e1dc4d49c8232beff7)
Devices with SMALL_FLASH enabled have "SQUASHFS_BLOCK_SIZE=1024" in
their config. This significantly increases the cache memory required by
squashfs [0]. This commit enables low_mem leading to a much better
performance because the SQUASHFS_BLOCK_SIZE is reduced to 256.
Example Nanostation M5 (XM):
The image size increases by 128 KiB. However, the memory statisitcs look
much better:
Default tiny build:
------
MemTotal: 26020 kB
MemFree: 5648 kB
MemAvailable: 6112 kB
Buffers: 0 kB
Cached: 3044 kB
low_mem enabled:
-----
MemTotal: 26976 kB
MemFree: 6748 kB
MemAvailable: 11504 kB
Buffers: 0 kB
Cached: 7204 kB
[0] - 7e8af99cf5
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit f54ac98f8cec676761e5144ae06640b8007b4b04)
ath79 has was bumped to 5.10. With this, as with every kernel change,
the kernel has become larger. However, although the kernel gets bigger,
there are still enough flash resources. But the RAM reaches its capacity
limits. The tiny image comes with fewer kernel flags enabled and
fewer daemons.
Improves: 15aa53d7ee65 ("ath79: switch to Kernel 5.10")
Tested-by: Robert Foss <me@robertfoss.se>
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit f4415f7635164ec07ddc22f56df93555804b5767)
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit eed0a31b90e4feeb65f3b54853bd4db1f5bcd524)
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit eff4f8b2f0a2900c945c21c8183d1faa0ac35ec1)
The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface
corresponding to the non-existing port.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 149fc3a269b435483b31df03d6fd9679286cf9e7)
At some point after 21.02.3 and before 22.03.0, the size limits of the
Linksys RE6500 were reached and prevent booting from the 22.03.0 release
or builds of current SNAPSHOT. This patch allows builds of master to boot
again and has been tested on my device.
Fixes: #8577
Signed-off-by: Mark King <mark@vemek.co>
(cherry picked from commit bf5b1a53d4ff3f1d742f9ece1ab16555280417ec)
Watchdog and poe_passthrough gpios require the jtag disabled.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
(cherry picked from commit 2ad949b11dbaa4c634868d55a4452d5a558776bd)
- fix including modules.mk when a target is being replaced
- fix calling make targets from target/linux
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 3a8825ad6acbf18b2b472ace56be58868af78be7)
Backports Linux kernel patch [1] for kernel 5.10 where it applies cleanly.
This was tested on CZ.NIC Turris 1.1 router running OpenWrt 22.03
release.
Before:
- In /var/log/messages:
```
[ 16.392988] lm90 0-004c: cannot request IRQ 48
[ 16.398280] lm90: probe of 0-004c failed with error -22
```
- Sensors does not work:
```
root@turris:~# sensors
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
```
After:
```
root@turris:/# sensors
sa56004-i2c-0-4c
Adapter: MPC adapter (i2c@3000)
temp1: +44.0°C (low = +0.0°C, high = +70.0°C)
(crit = +85.0°C, hyst = +75.0°C)
temp2: +73.8°C (low = +0.0°C, high = +70.0°C) ALARM (HIGH)
(crit = +85.0°C, hyst = +75.0°C)
```
[1] https://lore.kernel.org/linux-gpio/20220906105431.30911-1-pali@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 2f496c34b6dfbedbfbff8d2ade5d629f096e40bd)
(c&p commit ID from openwrt's master)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Broadcom's U-Boot contains environment data blocks. They need to be
found (offsets aren't predefined) to access env variables.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 137149847d0f374515f38952ce0986b03a97f2e4)
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb85 ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a78f ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a1192 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 117f41ee95ec445dce5ab9332bc27a6311747c0d)
Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[directly include v3 of the patchset submitted upstream]
(cherry picked from commit 31a6605de04218e1c04bd5c2436c24d7d1c07506)
(cherry picked from commit e785ca05e9f0502894772f5df92192b816ba5d7c)
(cherry picked from commit 412fcf3d4400f84551f3ead0514834c62d94a251)
The RGB LED of the UniFi 6 LR v1 doesn't work when using the Openwrt-
built U-Boot. This is because the vendor loader resets the ledbar
controller while our U-Boot doesn't care.
Add reset-gpio so the ledbar driver in Linux will always reset the
ledbar controller.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0b5cf952cf5b70d3af2424d05b15ce2730a3dc11)
Hardware
--------
- SoC: MediaTek MT7621AT with 128 MiB RAM and 32 MiB Flash
- Wi-Fi: MediaTek MT7603 (b/g/n, 2x2) and MediaTek MT7615 (ac, 4x4)
- Bluetooth: CSR8811 (internal USB, install kmod-bluetooth)
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Update the bootloader environment.
$ fw_setenv devmode TRUE
$ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr);
fdt rm /signature; bootubnt"
$ fw_setenv bootcmd "run boot_openwrt"
3. Transfer the OpenWrt sysupgrade image to the device using SCP.
4. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
5. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4
6. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock6
$ dd if=openwrt.bin of=/dev/mtdblock7
7. Reboot the device. It should boot into OpenWrt.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 820f0c07c544652c1c53a45262a481ac5dbe139b)
The patch adding support for LEDs connected to a reset controller did
not apply any more, refresh it on top of current master.
Fixes: 53fc987b2552 ("generic: move ledbar driver from mediatek target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 76fc277917fc847892dbbf525aea9f90a035d296)
This moves the ledbar driver to generic, to be also used by the ramips target.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 53fc987b25524c28525313347f0e2e5653dce43c)
The LEDs connected to the MCU are so-called smart LEDs and their signal is
daisy-chained. Because of this, the MCU needs to be told how many LEDs are
connected. It also means the LEDs could be individually controlled, if the MCU
has a command for this.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 76198e8f09a607c6aca2621f59d7a4cd7f6653e3)
During GPIO initialization the pin state flips and triggers a reset of
the ledbar MCU. It needs to be moved through an initialization sequence
before working correctly.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 013a956f086dc5d88f6e9cbd852ed4d900d436e0)
Some versions of the ledbar MCU have a reset pin. It needs to be
correctly initialized or we might keep the MCU in reset state.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 84e4bbf5f049cdb862eb25c446bd6973ed4238aa)
There are commands that return more than one byte of response.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 7c852e7df50e370b26b060c96c3cc4491cee88eb)
Or the comparison against a signed char is always true, because the
literal 0xaa is treated as an unsigned int, to which the signed char is
casted during comparison. 0xaa is above the positive values of a signed
char and negative signed char values result in values larger than 0xaa
when casted to unsigned int.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit e9a22ce2535c4a0faf83d5595304fe0e2c7bd1b2)
The read response is in the i2c_response variable. Also use %hhx format,
because we're dealing with a single char.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit c4f9f9b44c82ffeacd9d3c00ba07171c35831337)
It's already set to output with GPIOD_OUT_LOW.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit a188356484f434c72ea536d91d7f93f59c562eb5)
The polarity of the signal is set in the device dts.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
(cherry picked from commit 56c2d15587dfe5285f1cf3bfb236c827bc446465)
Janusz Dziedzic reported a typo introduced by a recent commit. Fix it.
Fixes: 50c892d67b ("mediatek: bpi-r64: make initramfs/recovery optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 007c8809c1e888748af70c1b878f4d0105fe7531)
Only include recovery image in SD card image generated for the
BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS
This allows to build images larger than 32 MB (the limit for
initramfs/recovery image) by deselecting initramfs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 50c892d67bb4af90861be9fbb6831c2eeb62de11)
Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.
Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired
to GPIO 3 or 4 and the wiring is currently unknown.
Set ethyellow-orange to display link state and activity of the ethyellow
interface for GB-PC2.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 2a6ef7f53d7b96e4ee0200196c28ed6b0a7c8465)
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit b77217d916ba48accbdb46589e6e5e3a9972c44e)
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 837fd23c80b22c566b40181a28630ac29af8f96e)
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit e8a62a1e6040de71bdcb1be1a1c30c064acbc059)
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit e0753c5d5cef5b03c60601364188afb262ccd02e)
Backport upstream solution that permits to declare nvmem cells with
dynamic partition defined by special parser.
This provide an OF node for NVMEM and connect it to the defined dynamic
partition.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1a9ee367343edce263f82cc91a49d796c9d45ea3)
Add the aliases sections required to detect LEDs specific to OpenWrt
boot / update indication for the NanoPi R4S.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1588069612f5db0720cbb942a6f8787878c223c3)
Ensure the MAC address for all NanoPi R4S boards is assigned unique for
each board.
FriendlyElec ship two versions of the R4S: The standard as well as the
enterprise edition with only the enterprise edition including the EEPROM
chip that stores the unique MAC address.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S in case the EEPROM chip is not
present by generating the board MAC from the SD card CID.
[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R4S#Differences_Between_R4S_Standard_Version_.26_R4S_Enterprise_Version
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b5675f500daff3ef3f904e53a5566aa7dc09b786)
The previous fixup was incomplete, and the offsets for the
queue and crc_error cpu_tag bitfields were still wrong on
RTL839x.
Fixes: 545c6113c93b ("realtek: fix RTL838x receive tag decoding")
Suggested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Add LTE packages required for operating the LTE modem optionally shipped
with the GL-AP1300.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c7c350922668e262068c9301b75434d7bb4b8d10)
Add support for the ZTE MF281 battery-powered WiFi router.
Hardware
--------
SoC: Qualcomm Atheros QCA9563
RAM: 128M DDR2
FLASH: 2M SPI-NOR (GigaDevice GD25Q16)
128M SPI-NAND (GigaDevice)
WLAN: QCA9563 2T2R 802.11 abgn
QCA9886 2T2R 802.11 nac
WWAN: ASRMicro ASR1826
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1
Unpopulated connector next to SIM slot
(SIM) GND - RX - TX - 3V3
Don't connect 3V3
BUTTON: Reset - WPS
LED: 1x debug-LED (internal)
LEDs on front of the device are controlled
using the modem CPU and can not be controlled
by OpenWrt
Installation
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.1.66 to the ethernet port.
Serve the OpenWrt initramfs image as "speedbox-2.bin"
3. Boot the initramfs image using U-Boot
$ setenv serverip 192.168.1.66
$ setenv ipaddr 192.168.1.154
$ tftpboot 0x84000000 speedbox-2.bin
$ bootm
4. Copy the OpenWrt factory image to the device using scp and write to
the NAND flash
$ mtd write /path/to/openwrt/factory.bin firmware
WWAN
----
The WWAN card can be used with OpenWrt. Example configuration for
connection with a unauthenticated dual-stack APN:
network.lte=interface
network.lte.proto='ncm'
network.lte.device='/dev/ttyACM0'
network.lte.pdptype='IPV4V6'
network.lte.apn='internet.telekom'
network.lte.ipv6='auto'
network.lte.delay='10'
The WWAN card is running a modified version of OpenWrt and handles
power-management as well as the LED controller (AW9523). A root shell
can be acquired by installing adb using opkg and executing "adb shell".
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1e1695f959e678868bb7911d059b847f38fc9cf4)
