9a509d4 ruleset.uc: consolidate ip and ip6 offload
21f311d ruleset.uc: don't trim newline before comment sign
f121383 tests: enable flow offloading in tests
550df40 tests: add test for unknown defaults option
47c5a5b tests: add test for deprecated rule option
69a89d6 tests: add test for unknown rule option
07579df fw4.uc: handle interface zone option
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Almost all targets have the fixed-phy feature built into the kernel.
One big exception is x86. This caused a problem with the upcoming
LAN78xx usb driver. Hence this patch breaks out the fixed-phy from
of_mdio (which didn't include the .ko) and puts into a separate
module.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
phy drivers for Microchip's LAN88xx PHYs.
This is needed for the "LAN7801" variant
of the upstream lan78xx usb ethernet driver.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
libdw depends on libfts.so when building with the musl-libc library, add
this missing dependency.
Fixes: 6835ea13f0 ("elfutils: update to 0.186")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Linux upstream commit 9370f2d05a
add load firmware file through request_firmware,this affect the
nanopi r2s and some USB adapters in kernel 5.10 with this error:
'r8152 4-1:1.0: unable to load firmware patch rtl_nic/rtl8153b-2.fw'
This patch split the USB NIC firmware files from r8169 firmware,
and adds r8152-firmware to r8152 driver.
Add kmod-usb-net-cdc-ncm to support RTL8156A and RTL8156B 2.5G ethernet
adapters supported since v5.13-rc1.
195aae321c
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Update busybox to 1.35.0
* refresh patches
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.35.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt configTARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in : change at "Options common to all shells" the symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
session tickets are a feature of TLSv1.2 and require less memory
and overhead on the server than does managing a session cache
Building mbedtls with support for session tickets will allow the
feature to be used with lighttpd-1.4.56 and later.
Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
Specifications:
- SoC: MT7621DAT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 128 MB NAND
- Ethernet: 5x 1GiE MT7530
- WiFi: MT7603/MT7613
- USB: 1x USB 3.0
This is another MT7621 device, very similar to other Linksys EA7300
series devices.
Installation:
Upload the generated factory.bin image via the stock web firmware
updater.
Reverting to factory firmware:
Like other EA7300 devices, this device has an A/B router configuration
to prevent bricking. Hard-resetting this device three (3) times will
put the device in failsafe (default) mode. At this point, flash the
OEM image to itself and reboot. This puts the router back into the 'B'
image and allows for a firmware upgrade.
Troubleshooting:
If the firmware will not boot, first restore the factory as described
above. This will then allow the factory.bin update to be applied
properly.
Signed-off-by: Nick McKinney <nick@ndmckinney.net>
CHECK_RUN_DIR=0 must be a part of MAKE_FLAGS, not MAKE_VARS, otherwise
it is not possible to compile mdadm on host without /run dir.
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
glibc version 2.34 does not provide versioned shared libraries any more,
it only provides shared libraries using the ABI version. Do not try to
copy them any more.
The functions from libpthread and librt were integrated into the main
binary, the libpthread.so and librt.so are only used for backwards
compatibility any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Provide uci-firewall via PROVIDES in both firewall and firewall4. This
will allow us to change the dependency of luci-app-firewall to
uci-firewall, making it possible to use it with either implementation.
Move CONFLICTS from firewall4 to firewall, to solve this recursive
dependency problem:
tmp/.config-package.in:307:error: recursive dependency detected!
tmp/.config-package.in:307: symbol PACKAGE_firewall is selected by PACKAGE_firewall4
tmp/.config-package.in:328: symbol PACKAGE_firewall4 depends on PACKAGE_firewall
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
4ead2a6 treewide: move executables to /sbin
9ebc2f4 fw4.uc: filter duplicates in fw4.set
85b74f3 treewide: support flow offloading
be3b4e6 treewide: support hardware flow offloading
38889b7 treewide: support set timeout
31c7550 fw4.uc: do not skip defaults with invalid option
334a127 fw4.uc: introduce DEPRECATED flag
7a0d38f fw4.uc: add _name as deprecated option
5e7ad3b fw4.uc: don't fail on unknown options
be5f4e3 fw4.uc: allow use of cidr in ipsets
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
The limitation of not being able to use iptables and nft nat at the same
time exists only in kernels before 4.18.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Jo-Philipp Wich <jo@mein.io>
ARC4 was used for WEP, which is not secure anymore. Therefor it is
disabled in the driver, but the code is not removed for now.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The lantiq AES hardware does not support the gcm algorithm. But it
can be implemented in the driver as a combination of the aes_ctr
algorithm and the xor plus gfmul operations for the hashing.
Due to the wrapping of the several algorithms and the inefficient
16 byte block by 16 byte block invokation in the kernel
implementations, this driver is about 3 times faster for the larger
block sizes.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
After adding xts and cbcmac the aes algorithm source had three sections
for setting the aes key to the hardware which are identical.
Method aes_set_key_hw was created which is now called from within the
spinlock secured control sections in methods ifx_deu_aes, ifx_deu_aes_xts
and aes_cbcmac_final_impl and reduces the size of ifxmips_aes.c.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Since commit 53b6783 hostapd is using the kernel api which includes the
cbcmac-aes shash algorithm. The kernels implementation is a wrapper around
the aes encryption algorithm, which encrypts block (16 bytes) by block.
When the ltq-deu driver is present, it uses hardware aes, but every 16 byte
encrypt requires setting the key. This is very inefficient and is a huge
overhead. Since the cbcmac-aes is simply a hash that uses the cbc aes
algorithm starting with an iv set to x'00' with an optional ecb aes
encryption of a possible last incomplete block that is padded with the
positional bytes of the last cbc encrypted block, this algorithm is now
added to the driver. Most of the code is derived from md5-hmac and
tailored for aes. Tested with the kernels crypto testmgr including extra
tests against the kernels generic ccm module implementation.
This patch also fixes the overallocation in the aes_ctx that is caused
by using u32 instead of u8 for the aes keys.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Remove the dependency on kernel 5.4 from the Makefile to allow the
driver to compile with kernel 5.10 or kernel versions higher than
5.4.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The lantiq AES hardware does not support the xts algorithm. Apart
from the cipher text stealing (XTS), the AES XTS implementation is
just an XOR with the IV, followed by AES ECB, followed by another
XOR with the IV and as such can be also implemented by using the
lantiq hardware's CBC AES implemention plus one additional XOR with
the IV in the driver. The output IV by CBC AES is also not usable
and the gfmul operation not supported by lantiq hardware. Both need
to be done in the driver too in addition to the IV treatment which is
the initial encryption by the other half of the input key and to
set the IV to the IV registers for every block.
In the generic kernel implementation, the block size for XTS is set
to 16 bytes, although the algorithm is designed to process any size
of input larger than 16 bytes. But since there is no way to
indicate a minimum input length, the block size is used. This leads
to certain issues when the skcipher walk functions are used, e.g.
processing less than block size bytes is not supported by calling
skcipher_walk_done.
The walksize is 2 AES blocks because otherwise for splitted input
or output data, less than blocksize is to be returned in some cases,
which cannot be processed. Another issue was that depending on
possible split of input/output data, just 16 bytes are returned while
less than 16 bytes were remaining, while cipher text stealing
requires 17 bytes or more for processing.
For example, if the input is 60 bytes and the walk is 48, then
processing 48 bytes leads to a return code of -EINVAL for
skcipher_walk_done. Therefor the processed counter is used to
figure out, when the actual cipher text stealing for the remaining
bytes less than blocksize needs to be applied.
Measured with cryptsetup benchmark, this XTS AES implementation is
about 19% faster than the kernels XTS implementation that uses the
hardware ECB AES (ca. 18.6 MiB/s vs. 15.8 MiB/s decryption 256b key).
The implementation was tested with the kernels crypto testmgr against
the kernels generic XTS AES implementation including extended tests.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The processing in the hmac algorithms depends on the status fields:
count, dbn and started. Not all were initialised in the init method
and after finishing the final method. Added missing fields to init
method and call init method after finishing final.
The memsets have the wrong size in the original driver and did not
clear everything and are not necessary. Since no memset is done in
the kernels generic implementation, memsets were removed.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Removing hash pointer in _hmac_setkey since its not needed and causes
a compiler warning.
Make the spinlock control sections shorter and move initializations
out of the control sections to free the spinlock faster for allowing
other threads to use the hash engine.
Minor improvements for indentation and removal of blanks and blank
lines in some areas.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Exceeding the temp array size was not checked and instead storage not
allocated by the driver was used/overwritten which in most cases
resulted in reboots. This patch implements processing the input to the
hash algorithm in tempsize chunks.
The _hmac_final methods were changed to _hmac_final_impl adding a
parameter that indicates intermediate or final processing. The started
variable was added to the context to indicate, if there is an
intermediate result in the context. For sha1_hmac the variable to store
the intermediate hash was added to the context too.
In order to avoid md5_hmac_final_impl being recursively called if the
padding of the input and the resulting last transform during the hmac
algorighms final processing causes the temp array to overflow and to
make sure that there is at least one block in the temp array when the
_hmac_final for final processing is called, the check for exceeding
the temp array in _hmac_transform was moved before copying the block
and incrementing dbn. dbn needs to be at least 1 at final processing
time to let the hash engine apply the opad operation.
To make the hash engine not apply the hmac algorithms final opad
operation, for intermediate processing the dbn in the control register
is set to a higher value than number of dbns are actually processed.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The hmac algorithms state, that keys larger than the key size should be
hashed with the underlying hash algorithms and then those hashes are to
be used as keys. This patch implements this. In order to avoid allocating
a descriptor during setkey, a shash_desc pointer is added to the context.
Another issue for multithreaded callers is the shared temp array.
The temp array is static and as such would be shared among multithreaded
callers, which obviously would neither work nor produce correct results.
The temp array (4k size) is moved to the context and since the size of
the context is limited, it can only be defined as pointer otherwise the
initialisation of the hash algorithm fails.
The allocations and freeing of both the temp and the desc pointer in the
context are done by implementing cra_init and cra_exit functions for
the hmac algorithms.
Also improved indentation in some areas.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Error ifxdeu-ctr-rfc3686(aes) (16) doesn't match generic impl (20) occurs
when running the cryptomgr extra tests that compare against the linux
kernels generic implementation.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The algorithms sha1, sha1_hmac and md5_hmac all use ENDI=1. The md5
algorithm uses ENDI=0 and the endian_swap methods to reverse the
endianess switch by using user CPU time, which is unnecessary overhead.
Danube and AR9 devices do not set endianess for SHA1, so is done for
MD5.
Furthermore the patch replaces endian_swap with le32_to_cpu for md5 and
md5 hmac algorithms and removes endian_swap for them.
The init functions initialize the algorithm in the hardware. The lock is
not used to write to the control register. If another thread calls
another hash algo before update or final, the result will be wrong.
Therefore move the algorithm init to the lock protected sections in the
transform or final methods.
Setting the hw key for the hmac algorithms is now done from within the
lock protected sections in their final methods. The lock protecting is
removed from the _hmac_setkey_hw functions.
In final for md5 and sha1 the lock section is removed, because all the
work was already done in transform (which is called from final). As such
only copying the hash to the output is required.
MD5 and MD5_HMAC produce 16 byte hashes (4 DWORDS) only, therefor
writing register D5R to the hash output is removed for MD5_HMAC.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
All hash algorithms use the same base IFX_HASH_CON to access the hash unit.
Parallel threads should not be able to call different hash algorithms and
therefor a global lock is required.
Fixed linker warning, that md5_hmac_init, md5_hmac_update and
md5_hmac_final are static export symbols. The export symbols are not
required, because the functions are exposed using shash_alg structure.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The functions ifx_deu_aes_cfg and ifx_deu_aes_ofb have been part of the
driver ever since. But the functions and definitions to make the
algorithms actually usable were missing.
This patch adds the neccessary code for aes_ofb and aes_cfb algorithms.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When running cryptomgr tests against the driver, there are several
occurences of different errors for even and uneven splitted data in the
underlying scatterlists for the ctr and ctr_rfc3686 algorithms which are
now fixed.
Fixed error in ctr_rfc3686_aes_decrypt function which was introduced with
the previous commit by using CRYPTO_DIR_ENCRYPT in the decrypt function.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When running cryptomgr tests against the driver, there are several
occurences of different errors for setkey of des and des3-ede
algorithms.
Those key checks are already implemented in the kernels des
implementation, so this is added as dependency and the kernel methods
are called. It also required adding the kernels des/des3 context
definitions to the des_ctx internal structure to be able to call the
kernel methods.
Fixed ifxdeu-des... setkey unexpectedly succeeded on test vector x;
expected_error=-22.
Fixed ifxdeu-des... setkey failed on test vector x; expected_error=0,
actual_error=-22.
Renamed des_ctx internal structure and des_encrypt/des_decrypt methods
because they are already defined in the kernel module.
Fixed wrong DES_xxx constant definitions in crypto_alg definition for
ifxdeu_des3_ede_alg.
Fixed method comment errors.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The <linux/cryptohash.h> was removed with Linux 5.8, because it only
contained the library implementation of SHA1, which was folded
into <crypto/sha.h>.
So switch this driver away from using <linux/cryptohash.h>.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Convert blkcipher to skcipher for the synchronous versions of AES,
DES and ARC4.
The Block Cipher API was depracated for a while and was removed with
Linux 5.5. So switch this driver to the skcipher API.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Some devices initialize AES during boot and AES works out of the box
and the correct endianess is set.
NDC means (No Danube Compatibility Mode) and the endianess setting has
no effect if its set to 0.
NDC 0: OFF ENDI bit cannot be written as in Danube
To make it work for other devices, the NDC control register needs to
be set to 1.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
OpenSSL with cryptdev support uses the data encryption unit (DEU) driver
for hard accelerated processing of ciphers/digests, if the flag
CRYPTO_ALG_KERN_DRIVER_ONLY is set.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Even if the minimum blocksize is set to 16 (AES_BLOCK_SIZE), the crypto
manager tests pass 499 bytes of data to the aes-ctr encryption, from
which only 496 bytes are actually encrypted.
Reading the comment regarding the minimum blocksize, it only states that
it's the "smallest possible unit which can be transformed with this
algorithm". Which doesn't necessarily mean, the data have to be a
multiple of the minimal blocksize.
All kernel hardware crypto driver enforce a minimum blocksize of 1,
which perfect fine works for the lantiq data encryption unit as well.
Lower the blocksize limit to 1, to process not padded data as well.
In AES for processing the remaining bytes, uninitialized pointers
were used.
This patch fixes using uninitialized pointers and wrong offsets.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
When handling non-aligned remaining data (not padded to 16 byte
[AES_BLOCK_SIZE]), a full 16 byte block is read from the input buffer
and written to the output buffer after en-/decryption.
While code already assumes that an input buffer could have less than 16
byte remaining, as it can be seen by the code zeroing the remaining
bytes till AES_BLOCK_SIZE, the full AES_BLOCK_SIZE is read.
An output buffer size of a multiple of AES_BLOCK_SIZE is expected but
never validated.
To get rid of the read/write behind buffer, use a temporary buffer when
dealing with not padded data and only write as much bytes to the output
as we read.
Do not memcpy directly to the register, to make used of the endian swap
macro and to trigger the crypto start operator via the ID0R to trigger
the register. Since we might need an endian swap for the output in
future, use a temporary buffer for the output as well.
The issue could not be observed so far, since all caller of ifx_deu_aes
will ignore the padded (remaining) data. Considering that the minimum
blocksize for the algorithm is set to AES_BLOCK_SIZE, the behaviour
could be called expected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
The crypto algorithms are registered and available to the system before
the chip is actually powered on and the generic parameter for the DEU
behaviour set.
The issue can mainly be observed if the crypto manager tests are enabled
in the kernel config. The crypto manager test run directly after an
algorithm is registered.
Signed-off-by: Mathias Kresin <dev@kresin.me>
[fix commit title prefix]
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Compiling without fPIC causes linking issues for packages using liblua.
Add $(HOST_FPIC) to host builds for both lua and lua5.3.
Suggested-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Arch Linux users have encountered problems with packages that have a dependency on binutils. This error happens when libtool is doing:
libtool: relink: ...
So change PKG_FIXUP to "patch-libtool".
Fixes error in the form of:
libtool: install: error: relink `libctf.la' with the above command
before installing it
Upstream Bug:
https://sourceware.org/bugzilla/show_bug.cgi?id=28545
OpenWrt Bug:
https://bugs.openwrt.org/index.php?do=details&task_id=4149
Acked-by: John Audia <graysky@archlinux.us>
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is a bugfix release. Changelog:
*) Avoid loading of a dynamic engine twice.
*) Fixed building on Debian with kfreebsd kernels
*) Prioritise DANE TLSA issuer certs over peer certs
*) Fixed random API for MacOS prior to 10.12
Patches were refreshed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Recently the hostapd has undergone many changes. The patches were not refreshed.
Refreshed with
make package/hostapd/{clean,refresh}
Refreshed:
- 380-disable_ctrl_iface_mib.patch
- 600-ubus_support.patch
- 700-wifi-reload.patch
- 720-iface_max_num_sta.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is required to be able to use flow offloading on devices with
ifnames that start with a digit, like 6in4-wan6.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Chromium based web-browsers (version >58) checks x509v3 extended attributes.
If this check fails then chromium does not allow to click "Proceed to ...
(unsafe)" link. This patch add three x509v3 extended attributes to self-signed
certificate:
1. SAN (Subject Alternative Name) (DNS Name) = CN (common name)
2. Key Usage = Digital Signature, Non Repudiation, Key Encipherment
3. Extended Key Usage = TLS Web Server Authentication
SAN will be added only if CONFIG_WOLFSSL_ALT_NAMES=y
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
x509v3 SAN extension is required to generate a certificate compatible with
chromium-based web browsers (version >58)
It can be disabled via unsetting CONFIG_WOLFSSL_ALT_NAMES
Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in>
NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6282 (1.6 GHz)
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 1x USB 2.0
- 2x USB 3.0
- 2x SATA
- 3x button
- 5x leds
- serial on J5 connector accessible from rear panel
(115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!)
Installation by USB + serial:
- Copy initramfs image to fat32 usb drive
- Connect pendrive to USB 2.0 front socket
- Connect serial console
- Stop booting in u-boot
- Do:
usb reset
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Installation by TFTP + serial:
- Setup TFTP server and copy initramfs image
- Connect serial console
- Stop booting in u-boot
- Do:
setenv bootargs 'console=ttyS0,115200n8 earlyprintk'
setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.2
tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage
bootm 0x1200000
- copy sysupgrade image via ssh.
- run sysupgrade
Known issues:
- Power button and PHY INTn pin are connected to the same GPIO. It
causes that every network restart button is pressed in system.
As workaround, button is used as regular BTN_1.
For more info please look at file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Tested-by: Raylynn Knight <rayknight@me.com>
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds kernel module for Global Mixed-mode Technology Inc
G762 and G763 fan speed PWM controller chips.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The build fails when the openssl/sha.h header file is not installed on
the host system. Fix this by setting the HOSTCCFLAGS variable to the
OpenWrt HOST_CFLAGS variable, without setting this the include paths and
other modifications in the host flags done by OpenWrt will be ignored by
the build.
This fixes the following build problem:
gcc -c -D_GNU_SOURCE -D_XOPEN_SOURCE=700 -Wall -Werror -pedantic -std=c99 -O2 -I../../include/tools_share fiptool.c -o fiptool.o
In file included from fiptool.h:16,
from fiptool.c:19:
fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
19 | # include <openssl/sha.h>
| ^~~~~~~~~~~~~~~
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The build of the manpages needs the pandoc tool, this is not in the
minimal requirements of OpenWrt, just remove the build of the restool
manpage. This fixes the build on systems without pandoc like the OpenWrt build bots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Up to now the WPS script triggered WPS on the stations only if it
could not trigger it successfully on any hostapd instance.
In a Multi-AP context, there can be a need (to establish a new
wireless backhaul link) to trigger WPS on the stations, regardless of
whether there is already a hostapd instance configured or not. The
current script makes it impossible, as if hostapd is running and
configured, WPS would always be triggered on hostapd only.
To allow both possibilities, the following changes are made:
- Change the "pressed" action to "release", so that we can make use of
the "$SEEN" variables (to know for how long the button was pressed).
- If the button is pressed for less than 3 seconds, keep the original
behavior.
- If the button is pressed for 3 seconds or more, trigger WPS on the
stations, regardless of the status of any running hostapd instance.
- Add comments explaining both behaviors.
- While at it, replace the usage of '-a' with a '[] && []'
construct (see [1]).
This gives users a "fallback" mechanism to onboard a device to a
Multi-AP network, even if the device already has a configured hostapd
instance running.
[1]: https://github.com/koalaman/shellcheck/wiki/SC2166
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
this patch consolidates the amd64-microcode
(moved to linux-firmware.git, previously this was an extra
debian source package download), amdgpu and radeon firmwares
into a shared "amd" makefile.
With the upcoming 20211216 linux-firmware bump,
this will include a microcode update for ZEN 3 CPUs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Otherwise, connection setup may fail due to JSON parse error in netifd.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Updated commit description]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
PIN2 is used only to restrict changing of fixed dialling feature,
does not affect network registration. Therefore explicitly check for
PIN1 state during connection setup, which is required for network
registration.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Updated commit description]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This is needed to properly close the control channel.
Otherwise, on the next try the caps call may fail.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
We were missing (not using) the last sector of each partition,
compared with the output of gparted.
Signed-off-by: Javier Marcet <javier@marcet.info>
[moved the dot]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The http://www.us.tcpdump.org mirror will go offline soon, only use the
normal download URL.
Reported-by: Denis Ovsienko <denis@ovsienko.info>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The rtl8723bs firmware was removed and a symlink to the rtl8723bu
firmware was created like it is done in upstream linux-firmware.
The following OpenWrt packages are changing:
* amdgpu-firmware: Multiple updates and new files
* ar3k-firmware: Multiple updates and new files
* ath10k-firmware-qca6174: Updated ath10k/QCA6174/hw3.0/board-2.bin
* bnx2x-firmware: Added bnx2x-e1-7.13.21.0.fw, bnx2x-e1h-7.13.21.0.fw and bnx2x-e2-7.13.21.0.fw
* iwlwifi-firmware-iwl8260c: Updated iwlwifi-8000C-36.ucode
* iwlwifi-firmware-iwl8265: Updated iwlwifi-8265-36.ucode
* iwlwifi-firmware-iwl9000: Updated iwlwifi-9000-pu-b0-jf-b0-46.ucode
* iwlwifi-firmware-iwl9260: Updated iwlwifi-9260-th-b0-jf-b0-46.ucode
* r8169-firmware: Updated rtl8153c-1.fw
* rtl8723bs-firmware: removed
* rtl8723bu-firmware: Added rtlwifi/rtl8723bs_nic.bin symlink
* rtl8822ce-firmware: Updated rtw8822c_fw.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on: 1ac627024d ("kernel: ath10k-ct: provide a build variant for
small RAM devices")
Like described in the ath10k-ct-smallbuffers version, oom-killer gets
triggered frequently by devices with small RAM.
That change is necessary for many community mesh networks which use
ath10k based devices with too little RAM. The -ct driver has been
proven unstable if used with 11s meshing and only wave2 chipsets are
supporting 11s. Freifunk Berlin is nowadays assembling its
firmware-based completely of vanilla OpenWRT with some package additions
which are made through the imagebuilder. Therefore we cannot take the
approach other freifunk communities have taken to maintain that patch
downstream [1]. Other communities consider these devices as broken and
that change would pretty much give those devices a second life [2].
[1] - 450b306e54
[2] - https://github.com/freifunk-gluon/gluon/issues/1988#issuecomment-619532909
Signed-off-by: Simon Polack <spolack+git@mailbox.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
The auto-ht option already kept HT and VHT support, but wasn't updated
to support HE (11ax).
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This device is based on NXP's QorIQ T2081QDS board, with a quad-core
dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5
ethernet interfaces, of which 3 are connected to the ethernet ports on
the front panel. The other 2 are internally connected to a Marvell
88E6171 switch; the other 5 ports of this switch are also connected to
the ethernet ports on the front panel.
Installation: write the sdcard image to an SD card. Stock U-Boot will
not boot, wait for it to fail then run these commands:
setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb
setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr'
saveenv
reset
The default U-Boot boot entry will now boot OpenWrt from the SD card.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add a new target named "qoriq", that will support boards using PowerPC
processors from NXP's QorIQ brand.
This doesn't actually add support for any board yet, so that
installation instructions can go in the commit message of the commit
that adds actual support for a board.
Using CONFIG_E6500_CPU here due to the kernel using -mcpu=powerpc64
rather than -mcpu=e5500 when selecting CONFIG_E5500_CPU. The only
difference between e5500 and e6500 is AltiVec support, and the kernel
checks for it at runtime. Musl will only check at runtime if AltiVec
support is disabled at compile-time, so we need to use e5500 in CPU_TYPE
to avoid SIGILL.
Math emulation (CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED) is required, as
neither e5500 nor e6500 implement fsqrt nor fsqrts, and musl hardcodes
sqrt and sqrtf to use these ASM instructions on PowerPC64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport an upstream patch to make libunwind build on ppc64, and add
powerpc64 to the dependencies.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
As of version 3.7, Nettle added PowerPC64 assembly for several
algorithms. Unfortunately, they cause build to fail due to ABI mismatch:
gcm-hash.o: ABI version 1 is not compatible with ABI version 2 output
Disable assembler when ppc64 and musl are used for now.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport an upstream patch that adds support for ELFv2 ABI on big endian
ppc64. As musl only supports ELFv2 ABI on ppc64 regardless of
endianness, this is required to be able to build OpenSSL for ppc64be.
Modify our targets patch to add linux-powerpc64-openwrt, which will use
the linux64v2 perlasm scheme. This will probably break the combination
ppc64 with glibc, but as we really only want to support musl, this
shouldn't be a problem.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Provide incoming BSS transition queries to ubus subscribers.
This allows external steering daemons to provide clients with
an optimal list of transition candidates.
This commit has no functional state in case no ubus subscriber is
present or it does not handle this ubus message.
To prevent hostapd from sending out a generic response by itself, a
subscribing daemon has to return a non-zero response code to hostapd.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport a patch to allow extending the ubus BSS-transition method
for specifying individual dialog tokens for BSS transition
management requests.
This is required for handling BSS transition queries in the future.
Signed-off-by: David Bauer <mail@david-bauer.net>
39b584b Revert "dhcpv6: add a minimum valid lifetime for IA_PD updates"
c9578e1 dhcpv6: add support for null IA_PD valid lifetime
ca43ea3 dhcpv6: add a minimum valid lifetime for IA_PD updates
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5ca5e0b netifd: allow disabling rule/rule6 config sections
8875960 interface-ip: add support for IPv6 prefix invalidation
e589c05 interface-ip: use metric when looking for a route
b54ffde main: fix hotplug script usage message
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This adds a new struct for storing statistics not (yet) tracked by
hostapd regarding RRM and WNM activity.
These statistics can be read using the get_status hostapd interface ubus
method.
Signed-off-by: David Bauer <mail@david-bauer.net>
Revert a commit to allow providing CFLAGS and LIBS from OpenWrt package
Makefile.
This downgrades the nl80211.h to kernel 5.15 and removes FILS_CRYPTO_OFFLOAD.
This is needed to make it compatible with our patched mac80211 from
kernel 5.15
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were backported from upstream before and are not
needed any more:
package/kernel/mac80211/patches/ath10k/081-ath10k-fix-module-load-regression-with-iram-recovery-feature.patch
package/kernel/mac80211/patches/ath10k/980-ath10k-fix-max-antenna-gain-unit.patch
package/kernel/mac80211/patches/build/010-headers-Add-devm_platform_get_and_ioremap_resource.patch
package/kernel/mac80211/patches/subsys/300-mac80211-drop-check-for-DONT_REORDER-in-__ieee80211_.patch
package/kernel/mac80211/patches/subsys/307-mac80211-do-not-access-the-IV-when-it-was-stripped.patch
package/kernel/mac80211/patches/subsys/308-mac80211-fix-radiotap-header-generation.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Just update PKG_VERSION/PKG_MIRROR_HASH since fman-ucode
of LSDK-21.08 had no changes.
Switched to AUTORELEASE for simplicity.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Update layerscape u-boot package to LSDK-21.08 and drop patches which
are no longer needed.
The new env variable 'fsl_bootcmd_mcinitcmd_set' is needed to protect
the configured bootcmd and mc_init values. See [1] for more
informations.
[1] b62c174e86
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
fdt* utils are needed by targets that use U-Boot FIT images for
sysupgrade. It includes all recent BCM4908 SoC routers as Broadcom
switched from CFE to U-Boot.
fdtget is required for extracting images (bootfs & rootfs) from
Broadcom's ITB. Extracted images can be then flashed to UBI volumes.
sysupgrade is core functionality so it needs dtc as part of base code
base.
Cc: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
update rtl8812au-ct driver to be ready for 5.15 Linux.
Signed-off-by: Janpieter Sollie <janpieter.sollie@edpnet.be>
[added commit message from PR with changes, added tag to subject]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The 'fils_dhcp' option can be set to '*' in order to autodetect the DHCP server
For proto=dhcp networks, the discovered dhcp server will be used
For all other networks, udhcpc is called to discover the address
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Among other things, this can be used to auto-configure the DHCP server
address for wireless APs using FILS, if the bridged interface is
configured to DHCP
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default CONFIG_BTRFS_FS_POSIX_ACL is disabled, it should be enabled
only when you enable CONFIG_FS_POSIX_ACL.
Right now, when you enable CONFIG_FS_POSIX_ACL it will enable
CONFIG_BTRFS_FS_POSIX_ACL, but it will be disabled once you install
kmod-btrfs. This should prevent it.
Btrfs has enabled by default ACL for mount option.
More details:
https://cateee.net/lkddb/web-lkddb/BTRFS_FS_POSIX_ACL.htmlhttps://btrfs.wiki.kernel.org/index.php/Manpage/btrfs(5)
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
The following command checks if a instance of a service is running.
/etc/init.d/<service> running <instance>
In the variable `$@`, which is passed to the function
`service_running`, the first argument is always the `instance` which
should be checked. Because all other variables where removed from `$@`
with `shift`.
Before this change the first argument of `$@` was set to the `$service`
Variable. So the function does not work as expected. The `$service`
variable was always the instance which should be checked. This is not
what we want.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
71e08471ab56 mt76: eeprom: fix return code on corrected bit-flips
9a8fc6636d83 mt76: move sar_capa configuration in common code
7cdbea1dc82a mt76: only access ieee80211_hdr after mt76_insert_ccmp_hdr
678071ef7029 mt76: mt7615: clear mcu error interrupt status on mt7663
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adds generic support for sysupgrading on eMMC-based devices.
Provide function emmc_do_upgrade and emmc_copy_config to be used in
/lib/upgrade/platform.sh instead of redundantly implementing the same
logic over and over again.
Similar to generic sysupgrade on NAND, use environment variables
CI_KERNPART, CI_ROOTPART and newly introduce CI_DATAPART to indicate
GPT partition names to be used. On devices with more than one MMC
block device, CI_ROOTDEV can be used to specify the MMC device for
partition name lookups.
Also allow to select block devices directly using EMMC_KERN_DEV,
EMMC_ROOT_DEV and EMMC_DATA_DEV, as using GPT partition names is not
always an option (e.g. when forced to use MBR).
To easily handle writing kernel and rootfs make use of sysupgrade.tar
format convention which is also already used for generic NAND support.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
CC: TruongSinh Tran-Nguyen <i@truongsinh.pro>
a6451fea5a3d mt76: mt7615: improve wmm index allocation
1911486414dc mt76: mt7915: improve wmm index allocation
7998a41d1321 mt76: clear sta powersave flag after notifying driver
664475574438 mt76: mt7603: introduce SAR support
5c0da39c940b mt76: mt7915: introduce SAR support
77fc6c439a32 mt76: mt7603: improve reliability of tx powersave filtering
094b3d800835 firmware: update mt7663 rebb firmware to 20200904171623
25237b19bcc1 mt76: eeprom: tolerate corrected bit-flips
1463cb4c6ac2 mt76: mt7921: fix boolreturn.cocci warning
586bad6020f7 mt76: mt7921: use correct iftype data on 6GHz cap init
8ec95c910425 mt76: mt7921s: fix bus hang with wrong privilege
688e30c7d854 firmware: update mt7921 firmware to version 20211014
6fad970893dd mt76: fix key pointer overwrite in mt7921s_write_txwi/mt7663_usb_sdio_write_txwi
95acf972750c mt76: fix 802.3 RX fail by hdr_trans
3f402b0cf6c0 mt76: mt7921s: fix possible kernel crash due to invalid Rx count
929a03a8d65d mt76: connac: fix last_chan configuration in mt76_connac_mcu_rate_txpower_band
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch is a revert of the upstream patch to Debian's ca-certificate
commit 033d52259172 ("mozilla/certdata2pem.py: print a warning for expired certificates.")
The reason is, that this change broke builds with the popular
Ubuntu 20.04 LTS (focal) releases which are shipping with an
older version of the python3-cryptography package that is not
compatible.
|Traceback (most recent call last):
| File "certdata2pem.py", line 125, in <module>
| cert = x509.load_der_x509_certificate(obj['CKA_VALUE'])
|TypeError: load_der_x509_certificate() missing 1 required positional argument: 'backend'
|make[5]: *** [Makefile:6: all] Error 1
...or if the python3-cryptography was missing all together:
|Traceback (most recent call last):
| File "/certdata2pem.py", line 31, in <module>
| from cryptography import x509
|ModuleNotFoundError: No module named 'cryptography'
More concerns were raised by Jo-Philipp Wich:
"We don't want the build to depend on the local system time anyway.
Right now it seems to be just a warning but I could imagine that
eventually certs are simply omitted of found to be expired at
build time which would break reproducibility."
Link: <https://github.com/openwrt/openwrt/commit/7c99085bd697>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Reported-by: Shane Synan <digitalcircuit36939@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
When compiling with CONFIG_USE_RFKILL=y, the build fails and mentions that
dependency on kmod-rfkill is missing, which is correct [1]. Add this
dependency to the Makefile.
Depend on +USE_RFKILL and not PACKAGE_kmod-rfkill, because it forces
selection of kmod-rfkill package. Other combinations in DEPENDS like
USE_RFKILL:kmod-rfkill or (+)PACKAGE_kmod-rfkill:kmod-rfkill do not force
selection of kmod-rfkill package.
The kmod-rfkill package itself depends on USE_RFKILL, so with +USE_RFKILL
in kmod-cfg80211 package it is not possible to select wrong combination of
packages.
[1] https://linux-wireless.vger.kernel.narkive.com/m8JY9Iks/cfg80211-depends-on-rfkill-or-not
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
If spectral scan support is enabled then ath10k-ct will cause a NULL
pointer due to relay_open() being called with a const callback struct
which is only supported in kernel 5.11 and later.
So, simply check the kernel version and if 5.11 and newer use the const
callback struct, otherwise use the regular struct.
Fixes: 553a3ac ("ath10k-ct: use 5.15 version")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The configs/omap3_overo_defconfig file was removed from upstream U-Boot
in commit ed3294d6d1f9 ("arm: Remove overo board"). Remove it in OpenWrt
too. If someone needs this please add it also to upstream U-Boot.
This fixes the compile of the omap target.
Fixes: ffb807ec90 ("omap: update u-boot to 2021.07")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.
The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.
See https://teltonika-networks.com/product/rutx10 for more info.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256MB DDR3
SPI Flash 1: XTX XT25F128B (16MB, NOR)
SPI Flash 2: XTX XT26G02AWS (256MB, NAND)
Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
USB Hub: Genesys Logic GL852GT
Bluetooth: Qualcomm CSR8510 (A10U)
LED/GPIO controller: STM32F030 with custom firmware
Buttons: Reset button
Leds: Power (green, cannot be controlled)
WiFi 2.4G activity (green)
WiFi 5G activity (green)
MACs Details verified with the stock firmware:
eth0: Partition 0:CONFIG Offset: 0x0
eth1: = eth0 + 1
radio0 (2.4 GHz): = eth0 + 2
radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.
The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt
USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.
Flash instructions via stock web interface (sysupgrade based):
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
5. Open stock web interface at http://192.168.1.1
6. Set some password so the web interface is happy
7. Go to firmware upgrade settings
8. Choose
openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
9. Set 'Keep settings' to off
10. Click update, when warned that it is not a signed image proceed
Return to stock firmware:
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
Add back support for the TLC591xx series LEDs which are used in the
ipq806x-based Meraki Cryptid series devices.
This module previously existed for the mvebu platform but was removed
at commit f849c2c832 due to being enabled
in that platform's kernel config.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
Currently nand_upgrade_tar() will pass the kernel length
to nand_upgrade_prepare_ubi() in all cases except for when
the kernel is to be installed in a separate partition as a
binary with the MTD tool.
While this is fine for almost all cases newer MikroTik NAND
devices like hAP ac3 require the kernel to be installed as a
UBIFS packed UBI volume in its own partition.
So, since we have a custom recipe to use ubiformat to flash
the kernel in its partition it makes no sense for sysupgrade
to also install the kernel as a UBI volume in the "ubi"
partition as it only wastes space and will never be used.
So, simply check whether CI_KERNPART is set to "none" and
if so unset the "has_kernel" variable which will in turn
prevent the kernel length from being passed on and then
the kernel UBI volume wont be created for no usefull purpose.
The ath79 MikroTik NAND target has been setting CI_KERNPART
to "none" for a while now altough that was not preventing
the kernel to be installed as UBI volume as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update ath10k-ct to get the upstream fix for
DFS support for VHT160 in the 5.15 based ath10k-ct.
(Switch from 5.10 to 5.15 surfaced the upstream regression.)
* refresh one patch
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Follow up to commit 565b62cca2. Managed to
hit the very same issue again while playing with the NOR SPL builds.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With cryptocpp in place we can now update past the point of dropping
the old tbb_linux binary and build it instead.
Hauke confirmed that this also allows this firmware to be built on
aarch64.
97f01f5 Wtpdownloader: Properly retrieve current tty options
a33ff86 Wtpdownloader: Set CREAD tty cflag
af461d2 Wtpdownloader: Fix stuck during opening UART tty device
38c2135 Makefile: Print error when specified CLOCKSPRESET is not valid
f014428 TBB: Remove out-of-dated x86-64 ELF binary tbb_linux
1b6cb50 TBB: Fix compilation with Crypto++ 5.6.5
d9fb291 TBB: Fix memory corruptions by calling correct delete[] operator
d575885 TBB: Fix initializing CCTIM object
b9e1c4e Wtpdownloader: Fix makefile
8f61591 Wtpdownloader: Fix building with gcc 11
eabea5f TBB: Fix building with gcc 11
Signed-off-by: Andre Heider <a.heider@gmail.com>
Based on the Build Instructions for Trusted-Firmware-A [1],
there is a required cryptopp [2].
In the past, it used 'tbb_linux' image tool binary, which seems to
be buggy, deprecated and removed from A3700-utils-marvell and it should
not be used anymore. That's why I removed 001-imagetool.patch, which is
no longer necessary.
[1] https://trustedfirmware-a.readthedocs.io/en/v2.5/plat/marvell/armada/build.html
[2] https://cryptopp.com/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
without this patch a3700-utils/tim/ddr/ddr_tool.verstr contains the OpenWrt commit ID.
this patch fix the mv_ddr version commit ID by using the global variable MV_DDR_COMMIT_ID.
Upon boot it now prints "mv_ddr-devel-g02e23dbc-d DDR4 16b 1GB 1CS".
Cc: Andre Heider <a.heider@gmail.com>
Signed-off-by: Kerma Gérald <gandalf@gk2.net>
We switched to mac80211 5.15 backport version.
Also switch ath10k-ct to 5.15 and drop the mac address patch
that got merged upstream.
Compile and tested on ipq806x Netgear R7800.
Also update the ath10k-ct to latest version to fix a typo
for the new version in the kernel log.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Add the beacon interval to hostapd status output. This allows external
services to discover the beacon interval for a specific VAP.
This way, external wireless management daemons can correctly calculate
fields containing TBTT value from absolute time-values.
Signed-off-by: David Bauer <mail@david-bauer.net>
If authentication fails repeatedly e.g. because of a weak signal, the link
can end up in blocked state. If one of the nodes tries to establish a link
again before it is unblocked on the other side, it will block the link to
that other side. The same happens on the other side when it unblocks the
link. In that scenario, the link never recovers on its own.
To fix this, allow restarting authentication even if the link is in blocked
state, but don't initiate the attempt until the blocked period is over.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some drivers that do their own sequence number allocation (e.g. ath9k, mwlwifi) rely
on being able to modify params->ssn on starting tx ampdu sessions.
This was broken by a change that modified it to use sta->tid_seq[tid] instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When procd-ujail is available, 1f78538387 runs hostapd as user
"network", with only limited additional capabilities (CAP_NET_ADMIN and
CAP_NET_RAW).
hostapd_cli (CONFIG_PACKAGE_hostapd-utils) communicates with hostapd
over a named UNIX-domain socket. hostapd_cli is responsible for creating
this socket at /tmp/wpa_ctrl_$pid_$counter. Since it typically runs as
root, this endpoint is normally created with uid root, gid root, mode
0755. As a result, hostapd running as uid network is able to receive
control messages sent through this interface, but is not able to respond
to them. If debug-level logging is enabled (CONFIG_WPA_MSG_MIN_PRIORITY
<= 2 at build, and log_level <= 2 in /etc/config/wireless wifi-device),
this message will appear from hostapd:
CTRL: sendto failed: Permission denied
As a fix, hostapd_cli should create the socket node in the filesystem
with uid network, gid network, mode 0770. This borrows the presently
Android-only strategy already in hostapd intended to solve the same
problem on Android.
If procd-ujail is not available and hostapd falls back to running as
root, it will still be able to read from and write to the socket even if
the node in the filesystem has been restricted to the network user and
group. This matches the logic in
package/network/services/hostapd/files/wpad.init, which sets the uid and
gid of /var/run/hostapd to network regardless of whether procd-ujail is
available.
As it appears that the "network" user and group are statically allocated
uid 101 and gid 101, respectively, per
package/base-files/files/etc/passwd and USERID in
package/network/services/hostapd/Makefile, this patch also uses a
constant 101 for the uid and gid.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
[refreshed patch]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix the return value, shell return codes should be 0 to indicate success
(i.e. mount point found), 1 should be failure (i.e. mount point not-found).
Fixes: ac4e8aa ("dnsmasq: fix more dnsmasq jail issues")
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Extend the hotplug.json ruleset to setup the common /dev/std{in,out,err}
symbolic links which are needed by some applications, e.g. nftables when
applying rulesets from stdin.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
8de12de system: add diskfree infos to ubus
bf3fe0e service: move jail parsing to end of instance parser
87b5836 procd: add full service shutdown prior to sysupgrade
01ac2c4 procd: service_stop_all: also kill inittab actions
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
5dd32475c859 mt76: mt7915: get rid of mt7915_mcu_set_fixed_rate routine
f5cfaaff3dd1 mt76: mt7921: drop offload_flags overwritten
f5ad840ca5c0 mt76: mt7615: fix possible deadlock while mt7615_register_ext_phy()
29a8a08827b1 mt76: mt7921: fix MT7921E reset failure
f44685f2faee mt76: mt7915: fix return condition in mt7915_tm_reg_backup_restore()
ae8e02ddd2b0 mt76: mt7915: fix SMPS operation fail
e814e15716b0 mt76: reverse the first fragmented frame to 802.11
c9bca3ed9566 mt76: mt7915: fix NULL pointer dereference in mt7915_get_phy_mode
dd054b7e16e7 mt76: only set rx radiotap flag from within decoder functions
f1520c9bb332 mt76: mt7915: add default calibrated data support
0c489ea2865a mt76: testmode: add support to set MAC
91c5da3d0a7c mt76: mt7921: add support for PCIe ID 0x0608/0x0616
ca39b4bbc227 mt76: debugfs: fix queue reporting for mt76-usb
00b6f497e2e8 mt76: mt7921: introduce 160 MHz channel bandwidth support
c1574466c733 mt76: fix possible OOB issue in mt76_calculate_default_rate
9680a17b0aed mt76: mt7921: fix possible NULL pointer dereference in mt7921_mac_write_txwi
78fc0dcdcef0 mt76: connac: fix a theoretical NULL pointer dereference in mt76_connac_get_phy_mode
05953e7d6fe7 mt76: mt7615: remove dead code in get_omac_idx
39f6c37127c1 mt76: connac: remove PHY_MODE_AX_6G configuration in mt76_connac_get_phy_mode
526591b203f3 mt76: do not pass the received frame with decryption error
256789bb400f mt76: fix the wiphy's available antennas to the correct value
fa187f5cf068 mt76: fix timestamp check in tx_status
11ebf11a3587 mt76: mt7915: fix the wrong SMPS mode
8c69b815ee7f mt76: mt7921: honor mt76_connac_mcu_set_rate_txpower return value in mt7921_config
bc6798f729f9 mt76: move sar utilities to mt76-core module
b1d0ad2e74fe mt76: mt76x02: introduce SAR support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allows to avoid rpath hacks with at least softethervpn.
--with-pic is needed as it's not default with static libraries, only
shared ones.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
cce5e35 vlist: define vlist_for_each_element_safe
This is change affects only a macro in headers and hence it is not
required to bump ABI_VERSION.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
68961a555e42 ubus: drop dnsmasq check for dns_result method
1ca3e26b8169 bpf: refactor code to support explicit opt-in for bulk+prio detection
3f0acf039f41 bpf: move flow prio/bulk detection config into a separate data structure
bc54c97e3333 map, bpf: create a separate map for configured dscp classes
46cf3eae2d99 bpf: fix bulk flow detaction
88f1db7dd611 bpf: fix priority flow detection
b5dec7874373 bpf: remove access to skb->gso_size
e728a319a9a5 interface: unify status, always include ifname, ingress, egress
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BTF pointer data has a different size on 32 vs 64 bit targets,
and while the generated eBPF code works, the BTF data fails to validate
on mismatch
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since sqm-scripts and qos-scripts packages are in the same category as qosify,
the firsts being in the Base System category, I find it understandable to move
the latter to Base System instead of network section.
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
On systems using brmcfmac (e.g. Raspberry Pi Zero W) without this fix,
the final setup-call:
iw dev wlan0 ibss join ...
fails with returncode 161 and message:
"command failed: Not supported (-95)"
So this patch calls an explicit:
iw dev wlan0 set type ibss
just prior to the 'ibss join' command.
I have tested several ath9k and mt76xx devices
with different revisions: this patch does not harm.
please also apply to stable branch.
Signed-off-by: Bastian Bittorf <bb@npl.de>
Update Telekom Speedport W921V firmware download URL.
Contained TAPI and VDSL firmware blobs are identical.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
19aae94 [build: avoid rebuilds of unset VARIANT packages] builds
packages defined without a VARIANT only once, using the first VARIANT
defined in the Makefile.
This caused problems with wpa-cli, as it is only built for variants that
include supplicant support, and the first VARIANT defined may not build
it.
The same happens to hostapd-utils, which is not built for
supplicant-only variants.
To circumvent this, set VARIANT=* for both packages so that they get
built for every defined variant. This should not cause spurious
rebuilds, since tey are not a dependency of any other package defined in
this Makefile.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
On lantiq a lot of stuff expects to be loaded to and executed at
0x80002000, including our own second stage bootloader.
For all build u-boots, the initial stack pointer is at 0x80008000. After
loading data to 0x80002000, every further stack operation corrupts the
loaded code.
Set the initial stack pointer to 0x80002000, to not overwrite code
loaded in memory. A stack of 0x2000 bytes has been proven as enough in
all done tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
On danube we only have 0x6800 bytes of usable SRAM. Everything behind
can't be written to and a SPL u-boot locks up during boot.
Since it's a hard to debug issue and took me more than two years to fix
it, I consider it worth to include fix albeit SPL u-boots are not build
in OpenWrt.
I faced the issue while trying to shrink the u-boot to 64K since some
boards only have an u-boot partition of that size from the days
ifx-uboot was used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With gcc10 the variables are placed more tightly to each other, which
uncovers a long existing bug in the lantiq DMA code. It can be observed
when using tftpboot with the filename parameter, which gets reset during
the tftpboot execution.
NetRxPackets[] points to cache line size aligned addresses. In
ltq_eth_rx_packet_align() the address NetRxPackets[] points to is
increased by LTQ_ETH_IP_ALIGN and the resulting not cache aligned
address is used further on. While doing so, the length/size is never
updated.
The "not cache aligned address" + len/size for a cache aligned address
is passed to invalidate_dcache_range(). Hence, invalidate_dcache_range()
invalidates the next 32 bit as well, which flashes the BootFile variable
as well.
variable BootFile is at address: 0x83ffe12c
NetRxPackets[] points to 0x83ffdb20 (len is 0x600)
data points to: 0x83ffdb22 (len is 0x600)
ltq_dma_dcache_inv: 0x83ffdb22 (for len 0x600)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffe120 (size: 32)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffdb40 (Bootfile: a.bin)
...
invalidate_dcache_range: 0x83ffe100 to 0x83ffe120 (Bootfile: a.bin)
invalidate_dcache_range: 0x83ffe120 to 0x83ffe140 (Bootfile: )
In ltq_dma_tx_map() and ltq_dma_rx_map() the start address passed to
ltq_dma_dcache_wb_inv() is incorrect. By considering the offset, the
start address passed to flush_dcache_range() is always aligned to 32, 64
or 128 bytes dependent on configured DMA burst size.
Fixes: FS#4113
Signed-off-by: Mathias Kresin <dev@kresin.me>
At least since gcc 7.3.0 (OpenWrt 18.06) lwr/lwl are used in the
assembly of LzmaProps_Decode. While the decission made by the compiler
looks perfect fine, it triggers some obscure hang on lantiq danube-s
v1.5 with MX29LV640EB NOR flash chips.
Only if the offset 1 is used, the hang can be observed. Using any other
offset works fine:
lwl s0,0(a1) - s0 == 0x6d000080
lwl s0,1(a1) - hangs
lwl s0,2(a1) - s0 == 0x0080xxxx
lwl s0,3(a1) - s0 == 0x80xxxxxx
It isn't clear whether it is a limitation of the flash chip, the EBU or
something else.
Force 8bit reads to prevent gcc optimizing the read with lwr/lwl
instructions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
eb0a3ee fw4.uc: Do not quote port ranges
c5a8e3e tests: adapt test to new ICMP print logic
Also start using $(AUTORELEASE)
Signed-off-by: Paul Spooren <mail@aparcar.org>
Simply reading /proc/*/stat as a space-separated string will not work
as the process name may itself contain spaces. Hence we must match on
the '(' and ')' characters around the process name and can then handle
the remaining string as space-separated values.
This fixes shell error messages which have been popping up the console
due to spaces in process names being interpreted as field separators.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The nl80211_set_wiphy() function was changed between kernel 5.11 and
5.12 to take the rdev->wiphy lock which should be freed at the end
again. The 500-mac80211_configure_antenna_gain.patch added some code
which just returned in some cases without unlocking. This resulted in a
deadlock with brcmfmac.
This patch fixes this by also jumping to the out label in case we want
to leave the function.
This fixes a hanging system when brcmfmac is in use. I do not know why
we do not see this with other driver.
The kernel returns very useful debug details when setting these OpenWrt
configuration options:
CONFIG_KERNEL_DETECT_HUNG_TASK=y
CONFIG_KERNEL_PROVE_LOCKING=y
Fixes: FS#4122
Fixes: b96c2569ac ("mac80211: Update to version 5.12.19-1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
from https://git.kernel.org/pub/scm/network/iproute2/iproute2.git
changes since 5.14.0:
ad3a118f rdma: Fix SRQ resource tracking information json
7a235a10 man: devlink-port: fix pfnum for devlink port add
229eaba5 uapi: pickup fix for xfrm ABI breakage
a500c5ac lib/bpf: fix map-in-map creation without prepopulation
7c032cac man: devlink-port: remove extra .br
04ee8e6f man: devlink-port: fix style
14802d84 man: devlink-port: fix the devlink port add synopsis
897772a7 cmd: use spaces instead of tabs for usage indentation
e7a98a96 mptcp: unbreak JSON endpoint list
2f5825cb lib: bpf_legacy: fix bpffs mount when /sys/fs/bpf exists
d756c08a tc/f_flower: fix port range parsing
92e32f77 uapi: updates from 5.15-rc1
e7e0e2ce iptuntap: fix multi-queue flag display
deef844b man: ip-link: remove double of
a3272b93 configure: restore backward compatibility
ceba5930 tree-wide: fix some typos found by Lintian
7a705242 ip: remove leftovers from IPX and DECnet
8ab1834e uapi: update headers from 5.15 merge
6d0d35ba ip/bond: add lacp active support
926ad641 Update kernel headers
c730bd0b ip/tunnel: always print all known attributes
df8912ed ipioam6: use print_nl instead of print_null
7e7270bb tc/skbmod: Introduce SKBMOD_F_ECN option
86c596ed IOAM man8
2d83c710 New IOAM6 encap type for routes
f0b3808a Add, show, link, remove IOAM namespaces and schemas
acbdef93 Import ioam6 uapi headers
2d6fa30b Update kernel headers
508ad89c ipneigh: add support to print brief output of neigh cache in tabular format
* update patch 170-ip_tiny.patch to accomodate ioam.
Signed-off-by: Russell Senior <russell@personaltelco.net>
0750f2b4d329 README: dnsmasq integration is complete
8e48d0b0cbba bpf: add initial support for splitting map dscp value into ingress and egress
bfc2cafe2a8c map: add support for defining aliases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We can't use booleans, since we're not including stdbool.h. Use integers
instead.
Fixes: 0b79e7c01e ("dnsmasq: generate the dns object name dynamically")
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
dnsmasq may call hotplug.dhcp, hotplug.neigh and hotplug.tftp.
Only the first two callees were listed in the ACL, so add missing
hotplug.tftp.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
9d1431e jail: allow passing environment variable to procd jailed process
Fixes dnsmasq in ujail which needs USER_SCRIPT env variable to be
passed to jailed process.
Reported-by: Bastian Bittorf <bb@npl.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When __ieee80211_select_queue is called, skb->cb has not been cleared yet,
which means that info->control.flags can contain garbage.
In some cases this leads to IEEE80211_TX_CTRL_DONT_REORDER being set, causing
packets marked for other queues to randomly end up in BE instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1fdf2a3 Fix kernel panic due to device deletion (#29)
e7b48d1 add the mutex lock for create/delete/config/insert nat46 devices to fix nat46 module crash issues. (#28)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
A set of tags can be specified for --dhcp-host option to restrict the
assignment to the requests which match all the tags.
Example usage:
config vendorclass
option networkid 'udhcp'
option vendorclass 'udhcp'
config host
option mac '*:*:*:*:*:*'
list match_tag 'switch.10'
list match_tag 'udhcp'
option ip '192.168.25.10'
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Now that wildcard matching is supported, this makes it easier for packages
to supply their own qosify rules
Signed-off-by: Felix Fietkau <nbd@nbd.name>
737970946bc0 map: default to fnmatch matching for dns patterns. support regex via leading /
b56b112e62e2 ubus: fix crash caused by missing static keyword
3a420e272c18 qosify: support wildcards in classifier filenames
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When installing additional rpcd modules, a restart of rpcd is required.
This often confuses users as even after installing rpcd-mod-rpcsys the
relevant ubus objects are still missing until rpcd has been reloaded
(or the system has been rebooted, obviously).
Let rpcd-mod-* reload rpcd as post-install action.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2ca7352543da map: make a helper function for freeing entries
411432ec853b map: add support for adding dns regex patterns
14803cb559d8 ubus: remove unused enum
a0740172eda6 ubus: add api for providing dns lookup results for dns regex rules
406fbf478e87 ubus: add support for dynamically adding dns based rules
5fc91183d60a README: mention dns regex entries
3ed8c3eb1a3b README: document mapping file syntax
91ce2e77d302 map: introduce low effort codepoint from RFC8622
5ff14acca0e7 interface: enable NAT on interfaces by default
e70f70e496d7 README: fix typo
f25ded617478 README: fix another typo
675238bc2ce5 loader: always reinitialize programs
010eea0d98c3 map: improve timeout handling of IP entries
7ef54a7f04a0 map: add DF codepoint
6f7fbe698555 map: increase active timeout to 300
60e06a579a13 qosify-bpf: inline check_flow() to ensure that it is jited
f5ae89e8d869 ubus: subscribe to dnsmasq.dns for dns lookup results
Signed-off-by: Felix Fietkau <nbd@nbd.name>
With "getting WIFI MAC from NVMEM" working on ath79 on 5.10,
the next logical step I think is to utilize nvmem subsystem
to also get the calibration data from there.
This will tremendously speed up the wifi bring-up, since
we no longer need the userspace helper for the simple
devices that can just load them from there.
included with this patch is a package/mac80211/refresh.
Tested on: WNDR3700v2, TP-Link Archer C7v2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
e303ba8 uqmi: update code generator
7880de8 uqmi: sync data from libqmi project
d647f8d uqmi: add more diagnostics commands
6f95626 uim: add --uim-get-sim-state
Use newly introduce --uim-get-sim-state command to query PIN status
from modems which require using uim instead of dms command for that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
20bf958 session: use uloop_timeout_remaining64
d11ffe9 session: use blobmsg_get_u64 for RPC_DUMP_EXPIRES
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Support for libsanitizer on MIPS 32 and MIPSEL 32 was added with GCC 9.
MIPS 64 and ARC are still not supported.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This version has some improvements for musl.
This version works fine for me on MIPS 32 BE without MIPS16 even on musl.
The additional patch is needed to make valgrind use the correct syscall
numbers for new syscalls like clock_gettime64. The MIPS architecture
uses special syscall ranges which are different from most other systems.
The patch is pending upstream: https://bugs.kde.org/show_bug.cgi?id=444781
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This implements the mapping recommendations from RFC8325, with an
update from RFC8622. This ensures that DSCP marked packets are properly
sorted into WMM classes.
The map can be disabled by setting iw_qos_map_set to something invalid
like 'none'
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Subtarget-specific files under 'uboot-envtools' package are supported
since 6f3a05ebb0 ("uboot-envtools: support uci-default config also per
subtargets").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
It relies on a custom ax_code_coverage.m4 file included with strace.
Unfortunately, this conflicts with the one included with
autoconf-macros. Instead of creating a huge patch to fix it, just remove
the variable as code coverage is not used here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Build the tc-mod-iptables before the tc-tiny and tc-full packages.
This avoids unnecessary package rebuild when calling make back to back.
Before this change, tc-mod-iptables will be built after the main tc
binary packages.
Both tc-tiny and tc-full depend on tc-mod-ipables. If make is called
after the packages are already built, it will check the timestamps of
both packages, and will rebuild the main binaries, since the module
package will be newer than the tc package.
Calling BuildPackage,mod-iptables first ensures that its variant gets
built before the other packages' variants.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Set the different libf2fs packages's VARIANT, so that the right settings
will be used by each different variant, if they are both being built.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Package hostapd-common is a dependency of every other package defined in
hostpad Makefile. It is currently built next to the bottom of that
Makefile's package list.
If you run make back to back, then check-compile will compare the
hostapd-common timestamp to the variant being compiled, to decide if the
varint needs to be rebuilt or not. Since the hostapd-conf package is
built towards the end of the list, it will be newer than most of the
variants, causing unnecessary package rebuilds.
Move it to the top, so that its timestamp will be older than dependent
packages, avoiding unnecessary rebuild of every selected variant.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
19fd7fc libfstools: make sure file is closed on error
d390744 libfstools: use uevent instead of relying on custom kernel patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
