Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes U-Boot modifications affecting the OpenWrt
installation.
Partition Table
| dev | size | erasesize | name |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000 | "spi0.1" |
| mtd1 | 00100000 | 00040000 | "BL2" |
| mtd2 | 00080000 | 00040000 | "u-boot-env" |
| mtd3 | 00200000 | 00040000 | "Factory" |
| mtd4 | 001c0000 | 00040000 | "FIP" |
| mtd5 | 00040000 | 00040000 | "zloader" |
| mtd6 | 04000000 | 00040000 | "ubi" |
| mtd7 | 04000000 | 00040000 | "ubi2" |
| mtd8 | 15a80000 | 00040000 | "zyubi" |
The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914
Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones
MAC Address Table
-----------------
eth0/lan Factory 0x002a
eth1/wan Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz Factory 0x0004 + 1
Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V | RX | TX | KEY | GND |
+---+---+-------+-------+-------+-------+
|
+--- Don't connect
Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.
1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.
2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.
3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI
4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1 # unlock write
atsw # swap boot partition
atsr # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.
Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)
Not working
----------------
voip (missing drivers or proper zyxel platform software)
Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.
Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC
Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
(cherry picked from commit 1c05388ab0)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr
lan 40:9b:xx:xx:xx:3c devdata@0x3f $label
wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 0ffbef9317)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Remove unnecessary new lines in the dts.
2. Remove duplicate included file "gpio.h" in the device dts.
3. Add missing button labels "reset" and "wps".
4. Unify the format of the reg properties.
5. Add u-boot environment support.
6. Reduce spi clock frequency since the max value suggested by the
chip datasheet is only 25 MHz.
7. Add seama header fixup for DIR-859 A1. Without this header fixup,
u-boot checksum for kernel will fail after the first boot.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit e5d8739aa8)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The x86_64 UML target wants to include SSSE3 optimized
crypto code which lives under /arch/x86/crypto.
However, these are not built and this causes an error.
| ERROR: module '[...]/arch/x86/crypto/sha512-ssse3.ko' is missing.
| make[3]: *** [modules/crypto.mk:990: [...]/kmod-crypto-sha512_5.15.112-1_x86_64.ipk] Error 1
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 959563fb81)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
That was a workaround for OpenWrt generation of config files. This patch
was used to postpone returning from probe function until loading
firmware and calling register_wiphy().
All of that is not needed anymore thanks to the ieee80211 hotplug.d
script introduced in the commit 5f8f8a3661 ("base-files, mac80211,
broadcom-wl: wifi detection and configuration"). That takes care of
generating /etc/config/wireless entries even if wireless device appears
late in the booting process.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit bd26266314)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, SSDK is rather special in the sense that its not being built as
a proper out of tree module at all but rather like a userspace application
and that involves a lot of make magic which unfortunately broke with make
version 4.4 and newer.
Luckily QCA finally added a way to build SSDK as an out of tree module
and it uses the kernel buildsystem which makes it compile with make 4.4
as well.
So lets backport the support for it and switch to using it.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 957f1ee85e)
IGD is only useful when accelerating a VM guest that wants to direct
render to memory in the host's framebuffer, but since OpenWrt
typically runs on headless hardware, this serves no purpose.
Also build vfio with VFIO_NOIOMMU undefined (to get all of the code
enabled), but allow it to be enabled via boot-time modparams
settings (or at run-time via sysfs writes to
"/sys/module/vfio/parameters/enable_unsafe_noiommu_mode".
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
adds ForceCommand option. If the command is specified,
it forces users to execute the command when they log in.
Signed-off-by: Nozomi Miyamori <inspc43313@yahoo.co.jp>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
A missing '\' caused the remaining parameters not to be passed to make.
This fixes the following error:
| gcc -c [...] fiptool.c -o fiptool.o
| In file included from fiptool.h:16,
| from fiptool.c:19:
|fiptool_platform.h:19:11: fatal error: openssl/sha.h: No such file or directory
| 19 | # include <openssl/sha.h>
| | ^~~~~~~~~~~~~~~
|compilation terminated.
|make[3]: *** [Makefile:58: fiptool.o] Error 1
as the HOST_CFLAGS are no longer passed.
then, HOST_CFLAGS is specified as a command argument, this
is a specific problem of our built since appending these
needs the override directive.
Fixes: df28bfe03247 ("tfa-layerscape: Change to github and use the latest tag")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of tfa-layerscape has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
v2:
* restored ls1021a-afrdm board
* added platform defines to fiptool so ls-ddr-phy can be built
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of ppfe-firmware has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of fman-ucode has been changed from
codeuaurora to github. Also use the latest tag for Layerscape
Linux Development POC from NXP.
Tested on:
* NXP LS1046A-RDB
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of uboot-layerscape has been changed
from codeuaurora to github. Also use the latest tag for
Layerscape Linux Development POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1028A-RDB
* NXP LS1046A-RDB
V2: Remove ls1028ardb specifix fixups not needed with new uboot
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The default location of ls-rcw has been changed from codeuaurora
to github. The reason is that the old codeaurora source no longer
resolves. Also use the latest tag for Layerscape Linux Development
POC from NXP.
Tested on:
* NXP FRWY-LS1012A
* NXP LS1046A-RDB
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
(reset PKG_RELEASE, Mention that previous codeaurora source is
no longer available)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The getrandom syscall is not hanging at bootup any more if there is
not enough entropy. This was fixed upstream in 2018 in commit:
a9cf659e05
This OpenWrt patch is not needed any more.
This reverts commit e64463ebde ("util-linux: avoid using the getrandom syscall")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following error:
* check_data_file_clashes: Package taskset wants to install file build_dir/target-powerpc_8548_musl/root-mpc85xx/usr/bin/taskset
But that file is already provided by package * busybox
* opkg_install_cmd: Cannot install package taskset.
Fixes: 3c3d797c4d ("busybox: enable taskset by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes errors in the form of:
/Users/user/src/openwrt/openwrt/build_dir/hostpkg/json-c-0.16/json_util.c:63:35: error: a function declaration without a prototype is deprecated in all versions of C [-Werror,-Wstrict-prototypes]
const char *json_util_get_last_err()
^
void
1 error generated.
ninja: build stopped: subcommand failed.
Reported-by: Paul Spooren <mail@aparcar.org>
Suggested-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove upstramed patches:
- 100-configure.ac-fix-AC_ARG_WITH.patch
- 101-configure.ac-fix-cross-compilation.patch
Remove deprecated f2fstat tool:
https://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs-tools.git/commit/?id=77bf7ed29f1dd1341079913f3b36fc62f812c4f5
Changelog:
06c027a f2fs-tools: upgrade version 1.16.0
542cc57 fsck.f2fs: fix sanity check logic for cp_payload
a7df89e mkfs.f2fs: remove indentation
c82985a fsck.f2fs: don't call report_zone on normal partition
0ac168e f2fs-tools: relax zone size of power of 2
641be32 mkfs.f2fs: trim all the devices except the first one
3835fef f2fs-tools: fix # of total segments
5b08ca9 f2fs_io: support AES_256_HCTR2
ae3301c f2fs_io: Fix out of tree builds
ddbde27 fsck.f2fs: relocate chksum verification step during f2fs_do_mount()
77bf7ed f2fs-tools: Remove deprecated f2fstat
fb6575e Remove sg_write_buffer
1bb669e fsck.f2fs: avoid uncessary recalculation
ccd2361 fsck.f2fs: fix potential overflow of copying i_name
cd6b133 fsck.f2fs: add parentheses for SB_MASK
399600a dump.f2fs: remove unavailable option -g
3e6e178 f2fs-tools: define HAVE_CLOCK_GETTIME properly
907b972 f2fs-tools: support F2FS_IOC_START_ATOMIC_REPLACE
9ff70fb f2fs-tools: give less overprovisioning space
844f821 f2fs-tools: set host-aware zoned device similar to host-managed one
88ac76d fsck.f2fs: fix missing to assign c.zoned_model
8cbe34e fsck.f2fs: trigger repairing if filesystem has inconsistent errors
2f1dde2 fsck.f2fs: trigger repairing if filesystem was forced to stop
465159f fsck.f2fs: export valid image size
3486b62 mkfs.f2fs: update allocation policy for ro feature
bdd51e5 fsck.f2fs: fix __end_block_addr()
5a5e419 Always use sparse/sparse.h when building for Android
19f77c6 f2fs-tools: fix build error on lz4-1.9.4
986c1f1 Fix format strings in log messages
0d6acbe fsck.f2fs: use elapsed_time in checkpoint for period check
9b7a4c5 mkfs.f2fs: catch total_zones=0 instead of crashing
6148db3 f2fs-tools: use F2FS_BLKSIZE instead of PAGE_*_SIZE
f09c2b7 f2fs_io: support triggering filesystem GC via ioctl
32e7d27 configure.ac: fix cross compilation
65fe94e configure.ac: fix AC_ARG_WITH
6325cf7 Use F2FS_BLKSIZE as the size of struct f2fs_summary_block
c89be7a Use F2FS_BLKSIZE for dev_read_block() buffers
5317d18 Improve compile-time type checking for f2fs_report_zone()
92e2e52 Fix f2fs_report_zone()
648a491 Fix the struct f2fs_dentry_block definition
c964547 resize.f2fs: add option to manually specify new overprovision
a741438 fsck.f2fs: drop compression bit if inline_data is set
406b1c9 f2fs-tools: fix cannot get bdev information
9d0cb9e f2fs_io: add dsync option for write
a7b8b46 tools: fix file too large causing overflow
bddca6f dump.f2fs: add -I nid to dump inode by scan full disk
ebc3879 android_config: add time headers
c1144bf Check fallthrough in mount.h for Mac
bcb9929 avoid unnecessary function
7d902f4 Fix dependencies on linux/blkzoned.h when using Bionic.
274abbb Remove unnecessary config.h
8c97ab3 libzone: remove duplicate header
adcec10 Support zoned device if libc exists
efc2bc7 mkfs.f2fs: fix typo
3034a41 mkfs.f2fs: split unused parameter
dd8d8e5 f2fs-tools: do not use SG_IO in Android
4f216e6 f2fs-tools: move android_config before defining them
48c5dbb f2fscrypt: adjust config file first
4b55459 android_config: add missing uuid library
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes the build of util-linux on powerpc and arc. Both CPU
architectures were not supported here in addition to the missing MIPS
support.
Fixes: 628a410ed1 ("util-linux: update to 2.39")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update to umdns HEAD to include latest enhancements for browse method
filtering, return of TXT records as an array, dumping IPv4/6 as an
array, and including the interface name in a browse reply.
Signed-off-by: Mark Baker <mark@vpost.net>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x, mt7621, x86_64
Add support for the FriendlyARM NanoPi R2C.
Manually generated of-platdata files to avoid swig dependency.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Instead of adding these common variables again and again simply create a
shared set for each SoC.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The Linux gpio-keys driver bindings allow for GPIO attached or interrupt
attached keys. Currently if an interrupt attached key is encountered
gpio_keys_button_probe() will fail due to not being able to get a gpio
descriptor:
gpio-keys: probe of gpio-keys failed with error -2
Skip the failure in the case of interrupt attached keys to resolve this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
5.15 is the first version to come with ksmbd. Use it instead of the
module as the linux one is better maintained.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This kernel config symbol is a shared library used for both CIFS and the
in-tree SMB_SERVER.
Split it out into kmod-fs-smbfs-common from kmod-fs-cifs, and depend on
it, so that later in-tree ksmbd may also depend on it.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
The BDFs for the:
Aruba AP-365
Devolo Magic 2 WiFi next
Edgecore ECW5410
Edgecore OAP100
Extreme Networks WS-AP3915i
GL.iNet GL-A1300
GL.iNet GL-AP1300
GL.iNet GL-S1300
Linksys EA8300
Linksys WHW03v2
Nokia Wi4A AC400i
P&W R619AC
Pakedge WR-1
Qxwlan E2600AC C1
Sony NCP-HG100/Cellular
Teltonika RUTX10
ZTE MF18A
were upstreamed to the ath10k-firmware repository
and landed in linux-firmware.git.
Furthermore the BDFs for the:
8devices Habanero
8devices Jalapeno
Qxwlan E2600AC C2
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
TOZED TL70-C is an LTE CAT6 cellular modem based on UNISOC SL8563. UNISOC
was formerly called Spreadtrum hence the manufacturer name detected on the
modem is spreadtrum.
The connect and disconnect commands bring up and down the usb0 interface.
They are Base64 encoded as that's what the AT command accepts. The modem
can do up to 4 APNs by bringing the USB interfaces, usb0 to usb3, up.
Setting the USB interfaces up:
connmanctl ndisdial AT^NDISDUN="usb0",1,1
connmanctl ndisdial AT^NDISDUN="usb1",1,2
connmanctl ndisdial AT^NDISDUN="usb2",1,3
connmanctl ndisdial AT^NDISDUN="usb3",1,4
Setting the USB interfaces down:
connmanctl ndisdial AT^NDISDUN="usb0",0,1
connmanctl ndisdial AT^NDISDUN="usb1",0,2
connmanctl ndisdial AT^NDISDUN="usb2",0,3
connmanctl ndisdial AT^NDISDUN="usb3",0,4
Co-developed-by: Andre Cruz <me@1conan.com>
Signed-off-by: Andre Cruz <me@1conan.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
add description for medion usb lte webstick
Signed-off-by: Joe Cooper <highjagger+github@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
8f78aff2cb68 ubus: support multiple call return values
51f4dba67313 ucode: also link libresolv if ns_initparse() is not found
5c7d07773a59 uci: fix ctx.commit() without arguments
5163867269fc Merge pull request #148 from jow-/uci-fix-commit
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
With the update of selinux no package depends anymore on pcre in the
base repository. Move it to packages feed.
Signed-off-by: Nick Hainke <vincent@systemli.org>
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Fixes error in the form of:
restripe.c: In function 'restore_stripes':
restripe.c:758:43: error: 'off64_t' undeclared (first use in this function); did you mean 'off_t'?
758 | (off64_t)read_offset) {
| ^~~~~~~
| off_t
restripe.c:758:43: note: each undeclared identifier is reported only once for each function it appears in
restripe.c:758:51: error: expected ')' before 'read_offset'
758 | (off64_t)read_offset) {
| ^~~~~~~~~~~
| )
restripe.c:757:36: note: to match this '('
757 | if (lseek64(source, read_offset, 0) !=
| ^
make[3]: *** [Makefile:193: restripe.o] Error 1
Fixes: fff878c5bc ("toolchain/musl: update to 1.2.4")
Signed-off-by: Nick Hainke <vincent@systemli.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces so
just having _GNU_SOURCE defined is not enough anymore.
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Fixes: fff878c5bc ("toolchain/musl: update to 1.2.4")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The firmware file for mt7601u (MediaTek MT7601U Wireless MACs) has
been moved to the mediatek/ folder by commit
8451c2b1 mt76xx: Move the old Mediatek WiFi firmware to mediatek
Address this by updating the location of the firmware file in our
linux-firmware Makefile generating the mt7601u-firmware package.
All other MediaTek Wi-Fi firmware files are supplied by OpenWrt's
own repository rather than being taken from linux-firmware.
Fixes: d53fe5d9ce ("linux-firmware: update to 20230515")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces so
just having _GNU_SOURCE defined is not enough anymore.
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Running autoreconf or autogen.sh is causing
the gettext-runtime subdirectory to have a configure script
that looks for and attempts to link to an external libunistring.
However, the macros and symbols for supporting that configuration
are not present in this subdirectory yet.
This results in some host machines to not build the
included libunistring objects for libgrt,
but at the same time, also not input the proper flag to the linker
for linking to an external library when it is found or even when
explicitly setting configuration to use a prefix for libunistring,
resulting in the common linking failure "undefined reference".
Some similar (and old...) upstream commits do the same thing,
but only for gettext-tools and libgettextpo.
Ref: ae943bcc1 ("Link with libunistring, if it exists.") # gettext.git
Ref: 61e21a72f ("Avoid link error in programs that use libgettextpo.") # gettext.git
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Add libunistring in order to link to gettext
and other packages directly
instead of the built-in substitute for it.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Fix compilation warning for unused variable for vr9.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c: In function 'mailbox_irq_handler':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c:560:9: error: unused variable 'i' [-Werror=unused-variable]
560 | int i;
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix multiple compilation warning for fallthrough and unused functions.
Fix compilation warning:
home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_VRX_TestParametersFeUpdate':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:3359:17: error: unused variable 'nMsgId' [-Werror=unused-variable]
3359 | DSL_uint16_t nMsgId = EVT_PMD_TESTPARAMSGET;
| ^~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:8310:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
8310 | bPreFail = DSL_TRUE;
| ~~~~~~~~~^~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:8316:7: note: here
8316 | case DSL_LINESTATE_EXCEPTION:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c:2328:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2328 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c:2331:4: note: here
2331 | case DSL_PM_RESET_TOTAL:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c: In function 'DSL_ModuleCleanup':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c:1266:13: error: assignment to 'dev_t' {aka 'unsigned int'} from 'void *' makes integer from pointer without a cast [-Werror=int-conversion]
1266 | dsl_devt = NULL;
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c: At top level:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c:1178:13: error: 'DSL_DRV_NlSendMsg' defined but not used [-Werror=unused-function]
1178 | static void DSL_DRV_NlSendMsg(DSL_char_t* pMsg)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_msg_vrx.c:2459:20: error: 'DSL_DRV_VRX_SpreadArray' defined but not used [-Werror=unused-function]
2459 | static DSL_Error_t DSL_DRV_VRX_SpreadArray(
| ^~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning related to stack limit.
Fix compilation warning:
/builder/shared-workdir/build/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-vectoring-2019-05-20-4fa7ac30/src/vectoring/ifxmips_vectoring.c: In function 'proc_write_dbg':
/builder/shared-workdir/build/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-vectoring-2019-05-20-4fa7ac30/src/vectoring/ifxmips_vectoring.c:369:1: error: the frame size of 2088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
369 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz
RAM: 2x Winbond W9751G6KB-25 (128 MiB)
FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB)
WIFI1: Atheros AR9550 5.0GHz (SoC)
WIFI2: Atheros AR9582-AR1A 2.4GHz
WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz
PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN)
LED: 1x Power-LED, 1 x RGB Tricolor-LED
INPUT: One Reset Button
UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8
(VCC, RX, TX, GND - VCC is closest to the boot set jumper
under the console pins.)
Flashing instructions:
Depending on the installed firmware, there are vastly different
methods to flash a MR18. These have been documented on:
<https://openwrt.org/toh/meraki/mr18>
Tip:
Use an initramfs from a previous release and then use sysupgrade
to get to the later releases. This is because the initramfs can
no longer be built by the build-bots due to its size (>8 MiB).
Note on that:
Upgrades from AR71XX releases are possible, but they will
require the force sysupgrade option ( -F ).
Please backup your MR18's configuration before starting the
update. The reason here is that a lot of development happend
since AR71XX got removed, so I do advise to use the ( -n )
option for sysupgrade as well. This will cause the device
to drop the old AR71xx configuration and make a new
configurations from scratch.
Note on LEDs:
The LEDs has changed since AR71XX. The white LED is now used during
the boot and when upgrading instead of the green tricolor LED. The
technical reason is that currently the RGB-LED is brought up later
by a userspace daemon.
(added warning note about odm-caldata partition. remove initramfs -
it's too big to be built by the bots. MerakiNAND -> meraki-header.
sort nu801's targets)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
d4f56f0e6971 add support for handling traffic to/from the bridge device
3ea579064c00 nl: add separate socket for netlink commands
4ec5a51c6d01 nl: fetch packet stats for offloaded flows
0319fd080bf5 add support for configuring a fixed output port for a bridge member port
5b730f0c2cf5 bridger-bpf: fix build on older kernels
00af6c6e8350 nl: process IFLA_MASTER in any nl events, but skip wireless events
a2794f95756e bridger-bpf: add bpf_skb_pull_data call
6974093eb036 nl: rework vlan code to use the iflink API
d0f79a16c749 nl: do not attempt to enable flow offload on older kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allowing the (kernel) packet priority to be set through UCI.
This makes it straightforward to set some VLAN priority for DHCP
requests through a simple egress qos map. (Avoiding the need for
firewall matching and marking through iptables, which prevents using
flow offloading).
(Such priority tag is a hard requirement for some ISPs, such as Orange
in France).
Depends on: https://github.com/openwrt/odhcp6c/pull/74
Signed-off-by: Pacien TRAN-GIRARD <pacien.trangirard@pacien.net>
We only use 5.15 kernel. So remove all those unnecessary symbols
referencing 5.10 or 5.15 kernel.
Can be found with:
git grep -E 'LINUX_5_1(0|5)'
Note that we remove the dependency from "sound-soc-chipdip-dac" instead
of removing the complete kernel package. The 5.15 version bump forgot to
delete the "@LINUX_5_10" dependency. The kernel package is still needed
in 5.15 kernel.
Signed-off-by: Nick Hainke <vincent@systemli.org>
We removed 5.10 kernel, so remove also the patch that only affects 5.10
kernels.
Manually refresh:
- 0005-SSDK-config-add-kernel-5.15.patch
- 0010-QSDK-config-Avoid-Werror-heroics.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fix compilation warning from ret not handled from copy_from_user and
missing fallthrough.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c: In function 'vmmc_BBD_WhiteListedCmdWr':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c:1012:16: error: this statement may fall through [-Werror=implicit-fallthrough=]
1012 | if (IFX_TRUE == pCh->pParent->bSlicSupportsIdleMode)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c:1028:7: note: here
1028 | case VMMC_WL_SDD_RING_CFG:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c: In function 'VMMC_Dev_Spec_Ioctl':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:111:15: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
111 | copy_from_user (p_arg, (IFX_uint8_t*)ioarg, sizeof(arg));\
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:475:7: note: in expansion of macro 'ON_IOCTL'
475 | ON_IOCTL((VMMC_CHANNEL *) pLLDummyCh,
| ^~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:113:15: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
113 | copy_to_user ((IFX_uint8_t*)ioarg, p_arg, sizeof(arg));\
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:475:7: note: in expansion of macro 'ON_IOCTL'
475 | ON_IOCTL((VMMC_CHANNEL *) pLLDummyCh,
| ^~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for switch fallthrough and
copy_to_user ret not handled.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c: In function 'ifx_tapi_dial_OnTimer':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c:318:38: error: this statement may fall through [-Werror=implicit-fallthrough=]
318 | pTapiDialData->nHookChanges = 0;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c:322:7: note: here
322 | case TAPI_HOOK_STATE_DIAL_L_VAL:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c: In function 'IFX_TAPI_Event_Dispatch_ProcessCtx':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c:1546:30: error: this statement may fall through [-Werror=implicit-fallthrough=]
1546 | pEvent->ch = IFX_TAPI_DEVICE_CH_NUMBER;
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c:1548:16: note: here
1548 | case IFX_TAPI_ERRSRC_LL_CH:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c: In function 'TAPI_IoctlDev':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:705:19: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
705 | copy_to_user ((IFX_void_t*)ioarg, p_tmp, sizeof(IFX_TAPI_CAP_t));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c: In function 'TAPI_IoctlCh':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:1553:14: error: this statement may fall through [-Werror=implicit-fallthrough=]
1553 | ret = TAPI_statusNotSupported;
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:1555:7: note: here
1555 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_fsm_alert_exec':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2037:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2037 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2039:7: note: here
2039 | case 1:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2053:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2053 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2055:7: note: here
2055 | case 2:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2070:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2070 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2072:7: note: here
2072 | default:
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_prepare_data':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1501:13: error: this statement may fall through [-Werror=implicit-fallthrough=]
1501 | if (IFX_TAPI_CID_HM_ONHOOK == pTxData->txHookMode)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1509:7: note: here
1509 | default:
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1531:16: error: this statement may fall through [-Werror=implicit-fallthrough=]
1531 | if (IFX_TAPI_CID_STD_KPN_DTMF_FSK != pConfData->nStandard)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1535:10: note: here
1535 | case IFX_TAPI_CID_GEN_TYPE_FSK:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_lookup_transparent':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1425:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
1425 | cidfsk_set_tx_time (pTxData, &pConfData->TapiCidFskConf);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1427:7: note: here
1427 | case IFX_TAPI_CID_GEN_TYPE_DTMF:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'TAPI_Phone_CID_Stop_Tx':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3445:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
3445 | switch (pTxData->nAlertType)
| ^~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3461:7: note: here
3461 | case TAPI_CID_STATE_ACK:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3463:13: error: this statement may fall through [-Werror=implicit-fallthrough=]
3463 | if (ptr_chk(pDrvCtx->SIG.DTMFD_Override, ""))
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3472:7: note: here
3472 | case TAPI_CID_STATE_SENDING:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'TAPI_Phone_Get_CidRxData':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:4060:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
4060 | if (IFX_Fifo_isEmpty(&(pCidRx->TapiCidRxFifo)))
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:4069:4: note: here
4069 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning caused by copy_from_user ret not handled.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ltq_atm.c: In function 'ppe_ioctl':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ltq_atm.c:341:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
341 | copy_from_user(&mib_vcc, arg, sizeof(mib_vcc));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning from missing fallthrough
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c: In function 'DSL_DRV_AutobootControlSet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c:2648:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
2648 | if (pContext->bAutobootThreadStarted)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c:2656:13: note: here
2656 | case DSL_AUTOBOOT_CTRL_STOP_PD:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2358:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2358 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2361:4: note: here
2361 | case DSL_PM_RESET_TOTAL:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2365:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2365 | if (ResetType == DSL_PM_RESET_TOTAL)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2368:4: note: here
2368 | case DSL_PM_RESET_HISTORY_SHOWTIME:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c:8883:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
8883 | bPreFail = DSL_TRUE;
| ~~~~~~~~~^~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c:8889:7: note: here
8889 | case DSL_LINESTATE_EXCEPTION:
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for some debugfs entry defined but
unused.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:969:12: error: 'proc_read_genconf' defined but not used [-Werror=unused-function]
969 | static int proc_read_genconf(char *page, char **start, off_t off, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:942:12: error: 'proc_write_wanmib' defined but not used [-Werror=unused-function]
942 | static int proc_write_wanmib(struct file *file, const char *buf, unsigned long count, void *data)
| ^~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:910:12: error: 'proc_read_wanmib' defined but not used [-Werror=unused-function]
910 | static int proc_read_wanmib(char *page, char **start, off_t off, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:892:12: error: 'proc_read_version' defined but not used [-Werror=unused-function]
892 | static int proc_read_version(char *buf, char **start, off_t offset, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:1164:19: error: 'stricmp' defined but not used [-Werror=unused-function]
1164 | static INLINE int stricmp(const char *p1, const char *p2)
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning due to not handled switch
fallthrough, stack limit and compilation warning in g997 module.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2277:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2277 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2280:4: note: here
2280 | case DSL_PM_RESET_TOTAL:
| ^~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2284:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2284 | if (ResetType == DSL_PM_RESET_TOTAL)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2287:4: note: here
2287 | case DSL_PM_RESET_HISTORY_SHOWTIME:
| ^~~~
cc1: all warnings being treated as errors
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c:3189:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
3189 | if (nErrCode != DSL_SUCCESS)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c:3197:13: note: here
3197 | case DSL_LINESTATE_IDLE:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c: In function 'DSL_DRV_DEV_G997_PowerManagementStateForcedTrigger':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c:2532:52: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
2532 | else if (((nVal >> 4) & 0x15) == 0x9)
| ^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c: In function 'DSL_DRV_DEV_G997_DeltHlogGet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c:2108:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
2108 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add multiple patch to make the package compilable again.
Aside from some fixup of obvius wrong code, some real fix were needed.
This fix any compilation warning found on compiling the package on
bcm47xx. (omitted since they are too much)
The real problem of this package was the missing MODULE_LICENSE now
mandatory even without WERROR. Set to Proprietary.
And the big blocker is that Broadcom provided an object file targetting
an old kernel version.
The module on modprobe try to find the symbol printk but printk was
dropped and replaced to _printk.
To handle this change we use objcopy tool to rename the symbol to the
new name permitting a correct modprobe and creation of .ko
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning on 64bit systems.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/fwcmd.c: In function 'mwl_fwcmd_get_fw_core_dump':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/fwcmd.c:3608:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
3608 | (const void *)((u32)pcmd +
| ^
In file included from ./include/linux/device.h:15,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/device.h:3,
from ./include/linux/dma-mapping.h:7,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/dma-mapping.h:3,
from ./include/linux/skbuff.h:31,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/etherdevice.h:3,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:20:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c: In function 'pcie_tx_init_ndp':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:38: error: format '%d' expects argument of type 'int', but argument 3 has type 'long unsigned int' [-Werror=format=]
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:17: note: in expansion of macro 'wiphy_err'
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:67: note: format string is defined here
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ~^
| |
| int
| %ld
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:38: error: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Werror=format=]
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:17: note: in expansion of macro 'wiphy_err'
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:71: note: format string is defined here
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ~^
| |
| int
| %ld
CC [M] /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.o
In file included from ./include/linux/device.h:15,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/device.h:3,
from ./include/linux/dma-mapping.h:7,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/dma-mapping.h:3,
from ./include/linux/skbuff.h:31,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/etherdevice.h:3,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:19:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c: In function 'pcie_bf_mimo_ctrl_decode':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:1325:37: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
1325 | filename, (unsigned int)fp_data);
| ^
./include/linux/dev_printk.h:110:37: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:1324:17: note: in expansion of macro 'wiphy_err'
1324 | wiphy_err(priv->hw->wiphy, "Error opening %s! %x\n",
| ^~~~~~~~~
cc1: all warnings being treated as errors
make[4]: *** [scripts/Makefile.build:289: /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.o] Error 1
make[4]: *** Waiting for unfinished jobs....
cc1: all warnings being treated as errors
make[4]: *** [scripts/Makefile.build:289: /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.o] Error 1
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.c: In function 'mwl_debugfs_regrdwr_read':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.c:1335:43: error: format '%d' expects argument of type 'int', but argument 4 has type 'ssize_t' {aka 'long int'} [-Werror=format=]
1335 | "error: %d(%u 0x%08x 0x%08x)\n",
| ~^
| |
| int
| %ld
1336 | ret, priv->reg_type, priv->reg_offset,
| ~~~
| |
| ssize_t {aka long int}
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Alloc MIB struct dynamically instead to fix compilation warning for
stack limit.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_chromium/vrx518_tc_drv-ugw_8.5.2.10/dcdp/ptm_tc.c: In function 'ptm_tc_get_stats':
/__w/openwrt/openwrt/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_chromium/vrx518_tc_drv-ugw_8.5.2.10/dcdp/ptm_tc.c:463:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
463 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for atm_tc module.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/vrx518_tc_drv-ugw_8.5.2.10/dcdp/atm_tc.c: In function 'print_datetime':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/vrx518_tc_drv-ugw_8.5.2.10/dcdp/atm_tc.c:768:32: error: argument to 'sizeof' in 'snprintf' call is the same expression as the destination; did you mean to provide an explicit length? [-Werror=sizeof-pointer-memaccess]
768 | snprintf(buffer, sizeof(buffer), "%s.%06d", tmbuf, (int)datetime->tv_nsec / 1000);
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop set_fs and get_fs since they are not present in kernel > 5.13.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c: In function 'dev_wlc_ioctl':
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:121:14: error: implicit declaration of function 'get_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
121 | fs = get_fs();
| ^~~~~~
| sget_fc
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:121:14: error: incompatible types when assigning to type 'mm_segment_t' from type 'int'
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:122:9: error: implicit declaration of function 'set_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
122 | set_fs(KERNEL_DS);
| ^~~~~~
| sget_fc
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:122:16: error: 'KERNEL_DS' undeclared (first use in this function); did you mean 'KERNFS_NS'?
122 | set_fs(KERNEL_DS);
| ^~~~~~~~~
| KERNFS_NS
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning related to if clause not guarding in
wl_iw.c
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c: In function 'wl_iw_set_freq':
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:393:9: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
393 | if (fwrq->m > 4000 && fwrq->m < 5000)
| ^~
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:396:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'if'
396 | chan = wf_mhz2channel(fwrq->m, sf);
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for copy_from_user ret value not handled.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c: In function 'DSL_BSP_FWDownload':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c:1623:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1623 | copy_from_user ((char *) &img_hdr_tmp, buf, sizeof (img_hdr_tmp));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c:1701:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1701 | copy_from_user (mem_ptr, buf + nRead, nCopy);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If CPTCFG_BRCMFMAC_SDIO is not used brcmf_of_fwnames is defined but not
used in the case of CONFIG_OF not compiled.
Restrict brcmf_of_fwnames only with CPTCFG_BRCMFMAC_SDIO selected.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.h:16:1: error: 'brcmf_of_fwnames' defined but not used [-Werror=unused-function]
16 | brcmf_of_fwnames(struct device *dev, u32 *map_count)
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for debug level read.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/ath10k-ct-regular/ath10k-ct-2022-05-13-f808496f/ath10k-5.15/debug.c: In function 'ath10k_read_debug_level': /__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/ath10k-ct-regular/ath10k-ct-2022-05-13-f808496f/ath10k-5.15/debug.c:1388:1: error: the frame size of 1440 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
1388 | }
| ^
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Handle error from copy_to_user in read_file_eeprom.
Fix compilarion warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/ath/ath9k/debug.c: In function 'read_file_eeprom':
/__w/openwrt/openwrt/openwrt/build_dir/target-x86_64-openwrt-linux-musl_musl/linux-x86_64/backports-6.1.24/drivers/net/wireless/ath/ath9k/debug.c:1451:17: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1451 | copy_to_user(user_buf, from, bytes);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
4c5beee get rid of VLA on the stack, and fix the resulting error of a too large stack frame
80dda1d Fix LAN->WAN ping failure with over MTU size on outgoing interface
Commit 4c5beee as a side effect fix a compilation warning with
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c: In function 'nat46_remove':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c:260:9: error: ISO C90 forbids variable length array 'config_remove' [-Werror=vla]
260 | char config_remove[buflen];
| ^~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-malta_be/nat46-2022-03-30-95ca1c3b/nat46/modules/nat46-netdev.c:280:17: error: ISO C90 forbids variable length array 'config' [-Werror=vla]
280 | char config[buflen];
| ^~~~
cc1: all warnings being treated as errors
Also this now require nf_defrag_ipv6 as a new dependency.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The index.json file lies next to Packages index files and contains a
json dict with the package architecture and a dict of package names and
versions.
This can be used for downstream project to know what packages in which
versions are available.
Signed-off-by: Paul Spooren <mail@aparcar.org>
When using OpenWRT with DSA and 'lan' ports, we could get an empty
`next_eth`. This is of course not desirable, as this causes `sh: out of
range` errors when trying to determine which one would be greater.
It turns out, that we don't even need this check at all because, when
looking for all existin eth*s on a system, and take the highest index
and then iterate a set of devices and rename to eth${highest_index+n},
it is guaranteed that there will be no conflict.
Fixes: b688bf83f9 ("base-files: rename ethernet devs on known boards")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Hardware specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 16 MB (Macronix MX25L12835FM2I-10G)
- RAM: 128 MB (Nanya NT5CC64M16GP-DI)
- WLAN 2.4 GHz: 2x2 MediaTek MT7603EN
- WLAN 5 GHz: 2x2 MediaTek MT7615N
- Ethernet: 1x 10/100/1000 Mbps
- LED: Power, Wifi, WPS
- Button: Reset, WPS
- UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port)
Serial console @ 57600,8n1
Flash instructions:
Connect to serial console and start up the device. As the bootloader got
locked you need to type in a password to unlock U-Boot access.
When you see the following output on the console:
relocate_code Pointer at: 87f1c000
type in the super secure password:
1234567890
Then select TFTP boot from RAM by selecting option 1 in the boot menu.
As Linksys decided to leave out a basic TFTP configuration you need to
set server- & client ip as well as the image filename the device will
search for. You need to use the initramfs openwrt image for the TFTP
boot process.
Once openwrt has booted up, upload the sysupgrade image via scp and run
sysupgrade as normal.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Kmod-mhi-pci-generic supports Qualcomm modems over PCIe bus. On targets
without PCI support, this package is empty. Symbol CONFIG_MHI_BUS_PCI_GENERIC
depends on CONFIG_PCI.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
