Commit Graph

3750 Commits

Author SHA1 Message Date
Matthias Schiffer
d168c2cf81
ar71xx: Ubiquiti Airmax M: add relocate-kernel to invalidate cache
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.

As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-26 20:40:07 +02:00
Kevin Darbyshire-Bryant
9aa196e0f2 kernel: bump 4.9 to 4.9.96
Refresh patches, following required reworking:

ar71xx/patches-4.9/930-chipidea-pullup.patch
layerscape/patches-4.9/302-dts-support-layercape.patch
sunxi/patches-4.9/0052-stmmac-form-4-12.patch

Fixes for CVEs:
CVE-2018-1108
CVE-2018-1092

Tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Arjen de Korte <build+openwrt@de-korte.org>
2018-04-26 08:53:54 +02:00
Matthias Schiffer
e39847ea2f
ar71xx: increase kernel partition size for CPE/WBS 210/510
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-10 18:29:19 +02:00
Matthias Schiffer
5bfb344106
ar71xx: sysupgrade: improve CPE/WBS 210/510 validation, add new metadata offset
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-10 18:29:19 +02:00
Matthias Schiffer
d3f96fedec
ar71xx: increase kernel partition size for UniFi AP Pro and Outdoor+, enable devices again
Tested on UAP Outdoor+.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-10 15:27:39 +02:00
Matthias Schiffer
f8f6fa11c0
ar71xx: limit Ethernet speed of UBNT Airmax M (XM) devices to 100Mbit/s
Some Airmax devices can establish a Gigabit link even though the MAC only
supports 10/100 MBit/s, leading to broken connectivity. Prevent this from
happening by limiting the speed to 100MBit/s.

Fixes: FS#296
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-10 15:27:39 +02:00
Henryk Heisig
c0742307a1 ar71xx: add support for TP-Link Archer C60 v2
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction (web):

Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.

Flash instruction (recovery):

1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
   rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
   directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server
8. Wait ~30 second to complete recovery

Flash instruction (under U-Boot, using UART):

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-04-07 00:09:05 +02:00
Robert Marko
b834487203 ar71xx: add support for TP-Link TL-WR940N v6
Add support for TL-WR940N v6 board. It is pretty much the same as v5
except they only left WAN LED and removed other ones.

Installation: flash factory image through WEB UI or use TFTP.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-04-06 23:11:00 +02:00
Piotr Dymacz
6148c46556 ar71xx: drop kernel 4.4 support
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
Peng Zhang
bbc2e1d919 ar71xx: change brand name WHQX to Qxwlan
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
2018-04-06 23:11:00 +02:00
Piotr Dymacz
57c641ba6e ar71xx: rework chipidea controller support, add QCA9531
Rework (again) platform support for dual-role chipidea USB controller:

- include support for QCA9531
- use correct EHCI block size
- drop ar933x_usb_setup_ctrl_config() function
- simplify code after previous "register chipidea only in device mode"
  change (fa22714181)

Reworked patch was tested on devices with below QCA WiSOCs (signal/GPIO
name with required bootstrap state for USB bus 0 in device mode):

- AR9331  (GPIO13 pull-down)
- AR9342  (RGMII_TXD1/ETXD1 pull-up)
- AR9344  (GPIO20 pull-up)
- QCA9531 (GPIO13 pull-up)
- QCA9558 (GPIO13 pull-up)

The only way to select device mode for bus 0 is to change SOC bootstrap
configuration which is sampled only once, at hard reset. Likely, other
models, like QCA9556 or AR9341, should also support dual-role USB mode
but they were not tested.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
David Bauer
f8dbafb234
ar71xx: add model detection for UBNT AC-Mesh
This commit adds correct model detection for UniFi
AC-Mesh. Previously said device was incorrectly detected
as UniFi AC-Lite.

The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-04-05 15:28:56 +02:00
Nicolò Veronese
d265a8f2ca
ar71xx: Add support for D-Link DAP-1330 a1
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)

Flash instruction: use "factory" image directly in vendor GUI.

This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.

You can access vendor firmware over serial using:
- login: root
- password: linuxrocks

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2018-04-05 15:28:56 +02:00
Reto Schneider
58fe527931 ar71xx: Fix typo in wan LED color of gl-mifi
It was wrong from the beginning and the trigger for the wan led was
never set due to the typo.

Signed-off-by: Reto Schneider <code@reto-schneider.ch>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-04 09:27:18 +02:00
Felix Fietkau
d7ca4c6d3e ar71xx: fix ar934x usb controller resource conflict
Use the right size for the EHCI block

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-28 23:08:37 +02:00
Mathias Kresin
26a9f01fc6 ar71xx: fix Fritz 300e initramfs image
Create an initramfs that can be used with the EVA bootloader.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-18 22:22:38 +01:00
Koen Vandeputte
895ea64a76 kernel: bump 4.4 to 4.4.121
- Refreshed all patches
- Only compile-tested

Compile tested on: Gemini

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-03-17 22:15:38 +01:00
Koen Vandeputte
fa8e99c51d kernel: bump 4.9 to 4.9.87
- Refreshed all patches

Compile tested on: ar71xx
Runtime tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-03-17 22:15:38 +01:00
Arne Zachlod
d0988235dd
ar71xx: add support for Ubiquiti Litebeam M5
Specification:
- SoC: Atheros AR9342
- Flash: 8 MiB
- RAM: 64 MiB
- UART: 1x UART on PCB - 115200 8N1
- Ethernet: 1 x 100 Mbit with passive PoE (24V/0.2A)

Doesn't work:
* Flash via TFTP with Ubiquiti Uboot

Installation via vendor firmware:
- upload factory image via webinterface

Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2018-03-15 19:11:39 +01:00
Felix Fietkau
fa22714181 ar71xx: fix double registration of usb host mode devices, add usb client support for qca955x
Only register the chipidea usb device if the strapping option indicates
device mode. If not, use the regular ehci platform driver.

Add qca955x device mode support, tested on 8devices Rambutan.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-09 18:25:57 +01:00
Felix Fietkau
83ddc3bfc2 ar71xx: fix mii bus irq assignment
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-04 19:37:20 +01:00
Felix Fietkau
f62d2b9549 ar71xx: remove pdata->fifo_cfg*
The values are the same for all chipsets that use it

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-04 19:37:20 +01:00
Stijn Segers
e72b2464b1 kernel: bump 4.4 to 4.4.119
This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.

* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).

Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.

Compile-tested on: ar71xx & oxnas.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
2018-03-03 12:58:56 +01:00
Magnus Kroken
5af85dab22 kernel: bump 4.9 to 4.9.85
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
2018-03-03 12:58:55 +01:00
Felix Fietkau
36fb0697e2 ar71xx: fix build with ag71xx debugfs support enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-28 13:57:58 +01:00
Rosen Penev
810659a22c ag71xx: Move timestamp struct member outside of struct.
With this change, the timestamp variable is only used in ag71xx_check_dma_stuck. Small tx speedup.

Based on a Qualcomm commit. ag->timestamp = jiffies was not replaced with netif_trans_update(dev) because of this quote:

It should be noted that after this series several instances
of netif_trans_update() are useless (if they occur in
.ndo_start_xmit and driver doesn't set LLTX flag -- stack already
did an update).

From: http://lists.openwall.net/netdev/2016/05/03/87

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-28 12:46:02 +01:00
Felix Fietkau
a49f6565b3 kernel: m25p80: allow fallback from spi_flash_read to regular SPI transfer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-26 19:20:06 +01:00
Piotr Dymacz
8c64824576 ar71xx: add support for GainStrong Oolite V5.2
GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on
module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are
available on castellated pins.

Specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet (all ports available on castellated pins)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11)
- 3x U.FL
- 1x USB 2.0

The dedicated development board includes 5 FE ports, USB 2.0 port, two
buttons (one directly connected to SOC reset input), header with all
GPIOs and several LEDs.

Flash instruction:

Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to
flash OpenWrt firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
907d674910 ar71xx: rework GainStrong devices support
- combine support for Oolite/MiniBox V1.0 in single mach-*.c file
- fix model/board names
- include correct/full vendor name
- drop redundant package and factory image

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
12c7b22e4e ar71xx: base-files: cosmetic cleanups in 04_led_migration
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
338a9fe8ad ar71xx: base-files: drop comment from 02_network
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Sebastian Kinne
950b278c81 ar71xx: add support for AR9331 based Hak5 devices
This adds support for AR9331 based Hak5 penetration testing tools:

- WiFi Pineapple NANO
- LAN Turtle
- Packet Squirrel

WiFi Pineapple NANO specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: 1T1R AR9331 (built-in), 1T1R AR9271 (built-in via USB bus)
- Ethernet: 1x FE over USB (ASIX AX88772A)
- Ports: 2x RP-SMA for antennas, 1x USB 2.0 (host), 1x micro SD
- Power: USB 5 V, 1.5 A
- Other: status LED, reset button

LAN Turtle specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 1x FE (AR9331), 1x FE over USB (Realtek RTL8152B)
- Ports: 1x RJ45, version dependent: micro SD or 3G SIM slot
- Power: USB 5 V, 0.5 A
- Other: status LED, reset button (inside, on PCB)

Packet Squirrel specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 2x FE (AR9331)
- Ports: 2x RJ45, 1x USB 2.0
- Power: USB 5 V, 0.12 A
- Other: status LED, reset button, 4-way switch

Flash instructions for all 3 devices:

Original firmware is based on OpenWrt.
Use sysupgrade via SSH to flash.

Signed-off-by: Sebastian Kinne <contact@sebkinne.com>
[squashed commits, combined and reworked mach files, aligned board
naming with general convention, fixed minor issues, tested on real
hardware, reworded commit subject and description]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Matti Laakso
2ea98fc39b ar71xx: fix 5 GHz Wi-Fi on NBG6716
Some NBG6716 do not have ath10k calibration data in flash, only in chip
OTP. To determine if flash has a valid calibration data, the first two
bytes telling the length of the calibration data are checked against the
requested length. If the lengths match, calibration data is valid and
read from flash.

Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
22ae9b742b ar71xx: YunCore AP90Q image supports also AP80Q
Vendor released new model (AP80Q) which is identical from hardware point
of view with already supported AP90Q. Include AP80Q in machine name.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
d6f187f938 ar71xx: add support for YunCore T830
YunCore T830 is a simple N300 router with 5-port FE switch, detachable
antennas and USB 2.0 port.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531), with ext. PA (SKY65174-21) and LNA
- two external, detachable antennas (RP-SMA)
- 1x USB 2.0
- 8x LED (7 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART and JTAG headers on PCB

Flash instruction:

1. First, gain root access to the device, following below steps:

- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to "Advanced" -> "Management" -> "System" and download backup of
  configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update "shadow" file and change
  hash of root password to something known.
- Repack the archive, rename it back to "bakfile.bin" and use to
  restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.

2. Then, install OpenWrt:

- Login over SSH and issue command:
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload "sysupgrade" image and install it (only if previous command
  succeeded) with command: "sysupgrade -n -F openwrt-...".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
e58e49bdbe ar71xx: add support for Samsung WAM250
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344. FCC ID: A3LWAM250.

Specification:

- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz (AR9344), with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)

Flash instruction:

This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.

You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).

1. Make sure that your device uses second (bootpart=2) image using
   command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
   latest vendor firmware (after the update, device should boot from
   second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
   wget, tftp or ftpget) to "/tmp" and issue below commands:

   mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
   mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
   fw_setenv bootpart
   fw_setenv bootcmd "bootm 0x9f070000"
   reboot

Revert to vendor firmware instruction:

1. Download vendor firmware to "/tmp" device and issue below commands:

   fw_setenv bootpart 1
   sysupgrade -n -F SS_BHUB_v2.2.05.bin

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
1b0e7a1453 ar71xx: fix COMFAST CF-E375AC support
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
650a5e993b ar71xx: add support for COMFAST CF-E385AC
COMFAST CF-E385AC is an AC2200 ceiling mount AP with PoE support, based
on Qualcomm/Atheros QCA9558 + QCA9984 + QCA8337N.

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 256 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet, with PoE support
- 3T3R 2.4 GHz (QCA9558), with external LNA and PA (SE2576L)
- 4T4R 5 GHz (QCA9984), with external FEM (SKY85728-11)
- 7x internal antennas
- 1x RGB LED (driven by GPIO)
- 1x button (reset)
- UART, LEDs/GPIO and USB headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
29d7c29046 ar71xx: remove unnecessary packages from COMFAST devices
swconfig and uboot-envtools packages are not required by any of the
supported COMFAST devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
106a56238f ar71xx: rename COMFAST CF-E355AC to CF-E355AC v1
There are now supported two versions of the CF-E355AC board which differ
in 802.11ac radio chip. Include version number in board, model, image
filename, etc., also for the v1.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
54b1be5f91 ar71xx: image: simplify Embedded Wireless definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
a679a45f0e ar71xx: image: generic: use simply expanded variables
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
3bc017fa3c ar71xx: image: generic: clean up trailing whitespace
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Ding Tengfei
e07014e70b ar71xx: add support for COMFAST CF-E355AC v2
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9886.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[updated kernel config for both boards]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Sven Eckelmann
b1d57dadb2 ar71xx: disable 40Mhz refclk for QCA953x
The "QCA9531 v2.0 802.11n 2x2 2.4 GHz Premium SOC for WLAN Platforms"
datasheet (80-Y7991-1 Rev. C - October 2014) doesn't specify support for a
40 Mhz reference clock. The register description for "Bootstrap Options"
(page 31) defines following states for the bit 4 (REF_CLK):

* 0 - CLK25 (default)
* 1 - (reserved)

Devices like the TP-Link CPE210 v2 has this bit set to 1 but is using a 25
Mhz reference clock. OpenWrt is still interpreted this bit as 40 Mhz and
then break the bootup of the system due to this incorrect interpretation.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[refreshed patches]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Peng Zhang
d8e6c3f6d9 ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB

WHQX E600G is based on Qualcomm QCA9531.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB

WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB

Important notice:

First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!

Flash instruction (using U-Boot CLI and tftp server):

1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
fc43e7a6e0 ar71xx: fix typos and indentation in Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Kyson Lok
bb1df2d75b ar71xx: include vendor name for GL iNet products
This patch include GL.iNet vendor name in the
machine name for GL.iNet vendor products.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
2018-02-22 18:53:22 +01:00
Kyson Lok
9dbfd8e9df ar71xx: uniform GL iNet products mach name
The mach name of GL AR150 and GL AR300 is inconsistent
with other products.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
2018-02-22 18:53:21 +01:00
Stijn Tintel
f621b53951 kernel: bump 4.9 to 4.9.82
Refresh patches.
Remove upstreamed patches:
- ar7/002-MIPS-AR7-ensure-the-port-type-s-FCR-value-is-used.patch
- backport/040-crypto-fix-typo-in-KPP-dependency-of-CRYPTO_ECDH.patch
Remove layerscape/819-Revert-dmaengine-dmatest-move-callback-wait-queue-to.patch,
it is superseded by upstream commit 297c7cc4b5651b174a62925b6c961085f04979fd.
Remove pending/650-pppoe_header_pad.patch, it is superseded by
upstream commit 1bd21b158e07e0b8c5a2ce832305a0ebfe42c480.
Update patches that no longer apply:
- ar71xx/004-register_gpio_driver_earlier.patch
- hack/204-module_strip.patch
- pending/493-ubi-set-ROOT_DEV-to-ubiblock-rootfs-if-unset.patch

Fixes CVE-2017-8824.

Compile-tested: ar71xx.
Runtime-tested: ar71xx.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-02-18 02:59:57 +01:00
Mathias Kresin
7a6de6d77a ar71xx: fix sysupgrade syntax error
Fix syntax error introduced with 188328111b ("treewide: move
nand_do_upgrade call to platform_do_upgrade").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-16 22:56:56 +01:00
Mathias Kresin
188328111b treewide: move nand_do_upgrade call to platform_do_upgrade
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").

Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-16 14:44:02 +01:00
Mathias Kresin
c4ac02ffca treewide: remove obsolete sysupgrade watchdog kill
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-16 14:44:02 +01:00
Julien Dusser
8dd455e3c4 ar71xx: add more registers to ar71x_regs.h
Add more registers and flags to ar71x_regs.h for QCA955x and QCA956x
SoCs. Values come from Qualcomm Atheros u-boot code.

Patches can be merged into
622-MIPS-ath79-add-more-register-defines-for-QCA956x-SoC.patch

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2018-02-13 11:20:58 +01:00
Karl Palsson
b2a5f7683b ar71xx: Add eTactica EG-200 support
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.

Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.

Flash instruction:
    Original firmware is based on OpenWrt.
    Use sysupgrade image directly in vendor GUI.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-02-13 10:01:53 +01:00
Henryk Heisig
a338491a30 ar71xx: add support for TP-Link RE355
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.

Specification:

720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB

Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-13 09:21:20 +01:00
Matthias Schiffer
355009ebe7
ar71xx: add missing config symbol ATH79_MACH_CF_E375AC
Fixes: bf66bb8c96 "ar71xx:add support for COMFAST CF-E375AC"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-02-11 18:41:25 +01:00
Ding Tengfei
bf66bb8c96 ar71xx:add support for COMFAST CF-E375AC
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.

Short specification:

    2x 10/100/1000 Mbps Ethernet, with PoE support
    128MB of RAM (DDR2)
    16 MB of FLASH
    3T3R 2.4 GHz, 802.11b/g/n
    2T2R 5 GHz, 802.11ac/n/a, wave 2
    built-in 5x 3 dBi antennas
    output power (max): 500 mW (27 dBm)
    1x RGB LED, 1x button
    built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
2018-02-11 16:20:24 +01:00
David Bauer
f17173f5a3 ar71xx: remove bs-partition ro-flag for UniFi AC
This removes the read-only flag from the bs (bootselect) partition
on UniFi AC devices. This allows to correct the indicator from which
partition the device is booting its kernel from.

See also:
 - https://github.com/freifunk-gluon/gluon/issues/1301
 - https://bugs.lede-project.org/index.php?do=details&task_id=662

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-02-11 16:16:03 +01:00
Arne Zachlod
186aebf90a
ar71xx: Orders the names of the devices alphabetically.
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2018-02-11 00:08:25 +01:00
Felix Fietkau
798497c66e ar71xx: use global timestamp for hang check
Shrink the size of struct ag71xx_buf to 8 bytes, which improves cache
footprint

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Felix Fietkau
31e6016d2e ar71xx: only access device stats in tx handler if packets were processed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Felix Fietkau
890e7458b0 ar71xx: allocate rx/tx descriptor/buffers in one chunk
Reduces false sharing due to cache aliases

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Rosen Penev
4e03a742e0 ag71xx: Reorder ag71xx struct members for better cache performance
Qualcomm claims this improves the D-cache footprint. Origina commit message below:

From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Fri, 7 Jun 2013 10:57:28 -0500
Subject: [ag71xx] cluster/align structs for cache perf

Cluster the frequently used, per-packet structures in ag71xx near
to each other, and cacheline-align them.  Some other re-ordering
occurred to move "warmer" structures near the per-packet structures.

Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-05 10:16:25 +01:00
Felix Fietkau
cde71a543c build: replace uses of OpenWrt with $(VERSION_DIST)
This makes the distribution name more configurable.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:15:53 +01:00
Matthias Schiffer
0c719bfcaf
ar71xx: /lib/ar71xx.sh: add model detection for TP-Link TL-WR810N
Properly report the revision in /tmp/sysinfo/model.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-02-03 14:13:26 +01:00
Matthias Schiffer
3f7908d697
ar71xx-generic: enable ATH79_MACH_TL_WR841N_V8 machine
This machfile also contains the code for the TL-WR842N/ND v2, which is in
ar71xx-generic and not in ar71xx-tiny.

Fixes: 0cd5e85e7a "ar71xx: create new ar71xx/tiny subtarget for 4MB flash
devices"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-31 21:18:16 +01:00
Catrinel Catrinescu
4ba2dd130a ar71xx: add ew-balin platform from Embedded Wireless
Add the Embedded Wireless "Balin" platform
 SoC: QCA AR9344 or AR9350
 RAM: DDR2-RAM 64MBytes
 Flash: SPI-NOR 16MBytes
 WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
 Ethernet: 3 x 10/100 Mb/s
 USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
 PCI-Express: 1 x lane PCIe 1.2
 UART: 1 x Normal, 1 x High-Speed
 JTAG: 1 x EJTAG
 GPIO: 10 x Input/Output multiplexed

The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2018-01-25 16:50:08 +01:00
Matthias Schiffer
ad4232e3e9
ar71xx: add unaligned access hacks for VXLAN
Gives a ~5% performance gain.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-25 11:00:48 +01:00
Daniel Golle
059b2f5481 ar71xx: fix MikroTik rb-nor-flash-16M-ac image
commit e15c63a375
ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)

changed the existing rb-nor-flash-16M-ac image in a way that it would
now only support the rb-wapg-5hact2hnd.
The board show however rather be added to the existing boards in the
rb-nor-flash-16M image template.

Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-01-24 01:24:39 +01:00
Gabor Juhos
eb9e3651dd ar71xx: add support for the MikroTik RB911-2Hn/5Hn boards
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:

  https://mikrotik.com/product/RB911-2Hn
  https://mikrotik.com/product/RB911-5Hn

The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.

Specifications:
  * SoC: Atheros AR9344 (600MHz)
  * RAM: 64MiB
  * Storage: 16 MiB SPI NOR flash
  * Ethernet: 1x100M (Passive PoE in)
  * Wireless: AR9344 built-in wireless MAC, single chain
              802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)

Notes:
  * Older versions of these boards might be equipped with a NAND
    flash chip instead of the SPI NOR device. Those boards are not
    supported (yet).
  * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
    same hardware. Support for that can be added later with little
    effort probably.

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its ethernet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

5. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

7. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:45 +01:00
Gabor Juhos
a4320b3332 ar71xx: make leds-gpio usable with single-ended GPIOs
Add patches for the leds-gpio driver to make it usable with
open-drain and open-source kind of GPIO lines.

This type of functionality is required by various MikroTik boards.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:32 +01:00
Gabor Juhos
e379e60b17 ar71xx: mach-rbspi: return rb_info from rbspi_platform_setup
Modify the rbspi_platform_setup() function to return the pointer of the
rb_info structure. This allows board specific setup routines to access
the various fields of the information. It is useful for investigating
the hardware option bits for example.

Also update the board setup codes, to ensure that those handle the new
return value correctly.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:16 +01:00
Gabor Juhos
c7371cd1ee ar71xx: add definitions for RouterBOARD hardware option bits
Add bit definitions for the 'hardware options' tag which is used in
the MikroTik devices' hardware configurations. These values can be
used in board setup codes, to do different initialization sequences.
The values were obtained from the RouterOS 6.41-rc38 patches.

Additionally, introduce two helper functions what make the processing
of the hardware options easy.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:00 +01:00
Kevin Darbyshire-Bryant
a30370bbf1 kernel: bump 4.4 to 4.4.112
Refresh patches.
Remove upstreamed patches:

target/linux/generic/patches-4.4/030-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/patches-4.4/030-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch
target/linux/generic/patches-4.4/030-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/patches-4.4/030-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch

CVEs completely or partially addressed:

CVE-2017-5715
CVE-2017-5753
CVE-2017-17741
CVE-2017-1000410

Compile-tested: ar71xx Archer C7 v2
Run-tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-01-20 20:22:01 +01:00
Gabor Juhos
ec4e9a88ff ar71xx: drop mdio-gpio.h include from mach-om5pacv2.c
The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.

Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.

Compile tested only.

Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Gabor Juhos
fbd33c2b6c ar71xx: fix format of the 701-MIPS-ath79-add-routerboard-detection patches
Commit e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAP
G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff
format, the unchanged, contextual lines must be preceded by a space
character.

Refresh the patches with quilt to fix them.

Fixes: e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Gabor Juhos
508999d366 ar71xx: fix format of the 741-MIPS-ath79-add-PCI-for-QCA9556-SoC patches
The patches introduced in commit 20e68f6d39 ("ar71xx: kernel: enable
PCI on QCA9556 SoC") have non standard format. In unified diff format,
the unchanged, contextual lines must be preceded by a space character.

Refresh the patches with quilt to fix them.

Fixes: 20e68f6d39 ("ar71xx: kernel: enable PCI on QCA9556 SoC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Gabor Juhos
bc178f6b15 ar71xx: mach-rbspi: simplify reset button registration
The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.

Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
David Bauer
6c56e968c1 ar71xx: fix TP-Link Archer C7 v4 switch LEDs
Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-01-15 21:45:43 +01:00
Piotr Dymacz
030176e0e7 ar71xx: image: rework EnGenius ENS202EXT factory image
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 13:39:54 +01:00
Roger Pueyo Centelles
e15c63a375 ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.

See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9556
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
   · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
 - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
   PoE in

Working:
 - Board/system detection
 - Sysupgrade
 - Serial console
 - Ethernet
 - 2.4 GHz radio
 - 5 GHz radio
 - Reset button

Not working:
 - LEDs (added according to Mikrotik's GPL sources but not functional)

 Unsupported:
 - ZT2046Q SPI temperature and voltage sensor

Contributors: Giuseppe Tipaldi (@Ciusss89)
              Ricky (@rickydee)

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
2018-01-15 04:14:18 +01:00
Roger Pueyo Centelles
20e68f6d39 ar71xx: kernel: enable PCI on QCA9556 SoC
This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.

Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-01-15 04:14:18 +01:00
Piotr Dymacz
2e5252d346 ar71xx: add support for GL.iNet GL-AR750
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
6cf682e214 ar71xx: image: move Sitecom WLR-8100 from legacy to generic
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Davide Fioravanti
a85db951db ar71xx: fix Sitecom WLR-8100 support
This patch fixes Sitecom WLR-8100:

- mtd layout
- LAN and WAN MAC address setup
- 2.4 GHz Wi-Fi MAC address setup
- 5 GHz Wi-Fi support (calibration data, MAC address setup, missing
  ath10k-* packages)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[squashed commits, fixed whitespace issues, reworded commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
af8f0629df ar71xx: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.

Specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
1f06144cde ar71xx: add support for Teltonika RUT900
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.

There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.

This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector

Serial console pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:09:43 +01:00
Piotr Dymacz
4b0eebe9df ar71xx: add support for ALFA Network N5Q
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 21:30:16 +01:00
Piotr Dymacz
7f9f42d42e ar71xx: add support for ALFA Network AP91-5G
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB

Flash instruction:

Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz
ce6c7691ec ar71xx: base-files: cosmetic cleanups in preinit scripts
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz
9a867fcddf ar71xx: base-files: drop LED control from 05_set_iface_mac_ar71xx
There is no "dir-615-c1:green:wancpu" LED defined in mach-dir-615-c1.c

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz
71489bfa48 ar71xx: base-files: fix boards order in 05_set_preinit_iface_ar71xx
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Matthias Schiffer
0cd5e85e7a
ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices
This new subtarget sets the small_flash flag and removes unused kernel
configuration.

small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Matthias Schiffer
29d126b5c1
ar71xx/generic: add generic- prefix to vendor-specific image Makefile snippets
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Matthias Schiffer
3d365831b0
ar71xx: reorganize kernel configuration
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Matthias Schiffer
d04056e5ea
ar71xx: disable devicetree support
While we'd like to convert ar71xx to DT-based configuration
eventually, we aren't quite there yet, and shipping half-baked DT support
that is not used at all wastes precious space.

Saves ~120KB before LZMA, ~33KB after LZMA.

Run-tested on TP-Link CPE510 and TL-WR841 v7.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-01-13 19:54:45 +01:00
Kevin Darbyshire-Bryant
efb375b579 kernel: bump 4.4 to 4.4.110
Refresh patches

Fixes:  CVE-2017-5754 aka Meltdown

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[fix typo in commit msg, conflict after 4.14 bump]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-10 00:11:39 +02:00
Kevin Darbyshire-Bryant
1d2590f838 kernel: bump 4.9 to 4.9.75
Refresh patches

Fixes:  CVE-2017-5754 aka Meltdown

Tested-on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[fix conflict after 4.14 bump]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-01-10 00:11:39 +02:00
David Bauer
daae09f1e5 ar71xx: fix Archer C7v4 5GHz MAC-address
The TP-Link firmware uses (primary_mac-1) as MAC-address
for the 5GHz WiFi. This applies the same behaviour to LEDE.

Currently, the MAC-address is retrieved from eth1, which
does not exist on the Archer C7 v4. As a result from this,
every C7 v4 with LEDE carries the same MAC-Address on the 5GHz WiFi.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-01-09 22:05:46 +01:00
Gabor Juhos
82cc439976 ar71xx: remove obsolete '< KERNEL_VERSION(4, 4, 0)' check
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:19 +01:00
Gabor Juhos
8f44c8086b ar71xx: remove obsolete '< KERNEL_VERSION(4, 2, 0)' check
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:18 +01:00
Gabor Juhos
7a4930b27c ar71xx: remove obsolete '< KERNEL_VERSION(3, 15, 0)' checks
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:18 +01:00
Gabor Juhos
99be4170cb ar71xx/mikrotik: disable TP-Link TL-WR810N v2 board support
It does not belongs to the MikroTik boards.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
7f7eb18455 ar71xx/mikrotik: disable unused MTD partitioning and split drivers
Reduces the compressed kernel size by ~2.5KB.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
660ee2d0f0 ar71xx/mikrotik: disable unused ethernet switch and phy drivers
Disable the drivers for the following ethernet switches:
  Realtek RTL8306
  Realtek RTL8366/8367
  Marvell 88E6060 (DSA)
  Marvell 88E6063 (DSA)

Also disable the phy driver for Marvell PHYs.

None of the supported RouterBOARDs are using any device
which needs these drivers.

Disable the DSA framework too, because it is not required
by the remaining switch drivers.

This reduces the compressed kernel size by ~20KB.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
b386b5727b ar71xx: fix Kconfig dependency of the 88E6063 switch DSA driver
The Marvell 88E6063 ethernet switch driver depends on the DSA
framework. Add a 'depends on NET_DSA' statement to its Kconfig
entry to state that explicitly.

Fixes the following Kconfig warning:

  warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6063) selects NET_DSA_TAG_TRAILER which has unmet direct dependencies (NET && NET_DSA)

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
09bb7105c2 ar71xx: sort kernel configurations
The symbols in some kernel configurations of the target are in
wrong order. Sort them with kconfig.pl.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 08:34:03 +01:00
Gabor Juhos
4045f15a21 ar71xx: fix compiler warnings in mdio-bitbang.c for 4.4
Building Linux 4.4 for ar71xx throws the following warnings in
drivers/net/phy/mdio-bitbang.c:

    CC      drivers/net/phy/mdio-bitbang.o
  In file included from include/linux/irqflags.h:14:0,
                   from drivers/net/phy/mdio-bitbang.c:20:
  drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_read':
  include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
    (void)(&__dummy == &__dummy2); \
                    ^
  include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
     typecheck(unsigned long, flags); \
     ^
  include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
     raw_local_irq_save(flags);   \
     ^
  drivers/net/phy/mdio-bitbang.c:162:2: note: in expansion of macro 'local_irq_save'
    local_irq_save(flags);
    ^
  include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
    (void)(&__dummy == &__dummy2); \
                    ^
  include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
     typecheck(unsigned long, flags); \
     ^
  include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
   #define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
                                         ^
  drivers/net/phy/mdio-bitbang.c:175:2: note: in expansion of macro 'local_irq_restore'
    local_irq_restore(flags);
    ^
  drivers/net/phy/mdio-bitbang.c:159:11: warning: unused variable 'i' [-Wunused-variable]
    int ret, i;
             ^
  In file included from include/linux/irqflags.h:14:0,
                   from drivers/net/phy/mdio-bitbang.c:20:
  drivers/net/phy/mdio-bitbang.c: In function 'mdiobb_write':
  include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
    (void)(&__dummy == &__dummy2); \
                    ^
  include/linux/irqflags.h:63:3: note: in expansion of macro 'typecheck'
     typecheck(unsigned long, flags); \
     ^
  include/linux/irqflags.h:124:3: note: in expansion of macro 'raw_local_irq_save'
     raw_local_irq_save(flags);   \
     ^
  drivers/net/phy/mdio-bitbang.c:185:2: note: in expansion of macro 'local_irq_save'
    local_irq_save(flags);
    ^
  include/linux/typecheck.h:11:18: warning: comparison of distinct pointer types lacks a cast
    (void)(&__dummy == &__dummy2); \
                    ^
  include/linux/irqflags.h:68:3: note: in expansion of macro 'typecheck'
     typecheck(unsigned long, flags); \
     ^
  include/linux/irqflags.h:126:39: note: in expansion of macro 'raw_local_irq_restore'
   #define local_irq_restore(flags) do { raw_local_irq_restore(flags); } while (0)
                                         ^
  drivers/net/phy/mdio-bitbang.c:200:2: note: in expansion of macro 'local_irq_restore'
    local_irq_restore(flags);
    ^

These are caused by the 900-mdio_bitbang_ignore_ta_value and
901-phy-mdio-bitbang-prevent-rescheduling-during-command patches.

The first patch removes some code but it does not remove the variable
which is used by the removed code only.

The second patch adds local_irq_{save,restore} calls. The type of the
argument of these calls must be 'unsigned long', but the patch defines
the variable as 'long'.

Fix both patches to silence the warnings.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-07 13:05:40 +01:00
Vittorio Gambaletta
d40a358136
ag71xx: Fix rx ring buffer stall on small packets flood on qca956x and qca953x.
Backported from Code Aurora QSDK

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2017-12-29 15:17:07 +01:00
Gabor Juhos
6456999731 ar71xx: spi-rb4xx: balance clk_prepare_enable() call
Commit c312cef223 ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call
with clk_prepare_enable() to meet the common clock framework requirements.
However it did not change the clk_disable() call in the error patch which
thus leads to imbalance.

Fix the code by using the correct counterpart of clk_prepare_enable() in both
places.

Fixes: c312cef223 ("ar71xx: spi-rb4xx fix.")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2017-12-24 09:03:01 +01:00
Roger Pueyo Centelles
82626cc145 ar71xx: add support for MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s)
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.

See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9558 (720 MHz)
 - RAM: 128 MB
 - Storage: 128 MB NAND
 - Wireless: external QCA9822 802.11a/ac 2x2:2
 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
 - SFP: 1x host

Working:
 - Board/system detection
 - NAND storage detection
 - Wireless
 - Ethernet
 - 1x user LED
 - Reset button
 - Sysupgrade

Untested:
 - SFP cage (probably not working)

Installation:
 - Boot initramfs image via TFTP and then flash sysupgrade image

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2017-12-21 17:06:54 +01:00
Roger Pueyo Centelles
9604f7d337 ar71xx: fix spelling in mach-rb922.c
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2017-12-21 17:06:54 +01:00
Roger Pueyo Centelles
8927446dae ar71xx: fix rb922gs_nand_scan_fixup()
Apply code from commits 9e1bc27e6d
(ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and
665bb27499 (ar71xx: fix invalid pointer
dereference in rb95x_nand_scan_fixup()) to RB92x devices too.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2017-12-21 17:06:54 +01:00
Hauke Mehrtens
f704b643b9 kernel: Update kernel 4.9 to 4.9.70
Runtime tested on lantiq.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-12-19 22:45:27 +01:00
Marty E. Plummer
7c03f97e84 ar71xx: fix lan ports on ens202ext
In the stock firmware both eth0 and eth1 are set to br-lan,
add this behavior to our images.

Fixes: FS#1084

Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
2017-12-18 09:10:12 +01:00
Gabor Juhos
665bb27499 ar71xx: fix invalid pointer dereference in rb95x_nand_scan_fixup()
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
chip->options causes an invalid pointer dereference (FS#1200).

Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.

Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2017-12-16 00:00:25 +01:00
Gabor Juhos
2ecc413107 ar71xx: fix invalid pointer dereference in c60_nand_scan_fixup()
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
the fields of the nand_chip structure causes an invalid pointer
dereference.

Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.

Compile tested only.

Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
2017-12-15 23:57:41 +01:00
kyson Lok
e776b6ed0b ar71xx: fix LED name typo for GL-AR300M
It shouldn't use double colon characters.

Signed-off-by: kyson Lok <kysonlok@gmail.com>
2017-12-15 23:50:21 +01:00
John Crispin
9f8d28285d Revert "ar71xx: TL-WR1043N v4/v5: add orange WAN LED support"
This reverts commit 256990cbc0.

this commit caused a compile error

"TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined.

Signed-off-by: John Crispin <john@phrozen.org>
2017-12-14 11:00:11 +01:00
Tim Thorpe
256990cbc0 ar71xx: TL-WR1043N v4/v5: add orange WAN LED support
Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and
v5. Minor format correction on a constant for consistency.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2017-12-14 09:29:31 +01:00
Henryk Heisig
85c1644a86 ar71xx: generate BR region-code factory image for TP-Link TL-WR940N
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-12-14 09:29:30 +01:00
João Chaínho
4d8a8c80d9 ar71xx: Fix switch port numbering on MIkrotik RB951Ui-2nD and RB493G
This patch fixes the switch port numbering on Mikrotik RB951Ui-2nD (hAP).
Also fixes the switch port numbering shown on LuCI for Mikrotik RB493G.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2017-12-14 09:29:30 +01:00
Jonas Gorski
eeeee885fb ar71xx: fix lzma-loader build with glibc
For an unknown reason gcc tries to link in crti.o when building with a
glibc toolchain (this does not happen with other targets). Prevent this
by telling gcc explicitly to not do that.

Fixes the following build error:

/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x18): relocation truncated to fit: R_MIPS_GOT16 against `__gmon_start__'
/home/jonas/git/lede/staging_dir/toolchain-mips_24kc_gcc-5.5.0_glibc/lib/gcc/mips-openwrt-linux-gnu/5.5.0/../../../../mips-openwrt-linux-gnu/lib/crti.o: In function `_init':
(.init+0x28): relocation truncated to fit: R_MIPS_CALL16 against `__gmon_start__'
collect2: error: ld returned 1 exit status

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-12-13 11:34:51 +01:00
Luis Araneda
575178e462 treewide: add only one device when appending to TARGET_DEVICES
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-12 18:47:26 +01:00
Gabor Juhos
e7b48fcfe1 ar71xx: fix board detection with newer RouterBOOT versions
Recent RouterBOOT version (at least version 3.41 on RB911G-5HPacD)
use "Board=" kernel parameter instead of "board=" to pass the board
name to the kernel. Due to this change the board detection code is
not working on the devices shipped with the new RouterBOOT version.
Because the kernel is unable to identify these boards they become
unusable despite that they are supported by the current code.

Update the prom_init code to convert the 'Board' kernel parameter to
'board'. After this change, the board detection works also with the
new RouterBOOT versions.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2017-12-12 17:05:25 +08:00
Mathias Kresin
0b8a1e75df ar71xx: remove nand_board_name platform override
The boardname isn't used any longer to find the subdirectory in the
sysupgrade tar archive, which makes this override useless.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-08 20:57:12 +01:00
Felix Fietkau
668eb70157 kernel: MIPS compile out no-op DMA mapping ops where possible
Slightly improves networking throughput on some devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-12-08 19:55:17 +01:00
Rosen Penev
1c2fdfbaf2 ag71xx: Reduce NAPI weight to 32.
Qualcomm claims this reduces cache misses. Original commit message below:

From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Tue, 11 Jun 2013 12:18:46 -0500
Subject: [ag71xx] reduce NAPI weight

In an attempt to increase our cache warmth, we are decreasing NAPI.
This increases the warmth of the reused SKBs.

Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-12-08 19:54:37 +01:00
Rosen Penev
524d103e7e Revert "ag71xx: Switch from driver to kernel macro for NAPI_WEIGHT."
The motivation for this was misguided. It turns out tuning the NAPI weight could be useful for testing purposes. Therefore reverting.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-12-08 19:54:34 +01:00
Zoltan HERPAI
7b5c989ab9 merge: targets: update image generation and targets
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2017-12-08 19:41:18 +01:00
David Bauer
5a8e9846af
ar71xx: C58/C59 fix LAN1 working incorrectly
This commit fixes LAN Port 1 not transferring data in case no
other LAN Port has active link-state on TP-Link Archer C58/C59.

Signed-off-by: David Bauer <mail@david-bauer.net>
2017-12-08 13:53:03 +01:00
Stijn Tintel
f997478655 kernel: bump 4.9 to 4.9.67
Refresh patches.
Remove upstreamed patches:
- generic/190-1-5-e1000e-Fix-error-path-in-link-detection.patch
- generic/190-3-5-e1000e-Fix-return-value-test.patch
- generic/190-4-5-e1000e-Separate-signaling-for-link-check-link-up.patch
- generic/190-5-5-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch
- ramips/0102-MIPS-ralink-Fix-MT7628-pinmux.patch
- ramips/0103-MIPS-ralink-Fix-typo-in-mt7628-pinmux-function
Update patches that no longer apply:
- layerscape/815-spi-support-layerscape.patch
- ramips/0099-pci-mt7620.patch

Compile-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64.
Runtime-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-12-07 01:41:09 +02:00
Rosen Penev
7a318bc1a1 kernel: Update kernel 4.4 to 4.4.100
Run-tested on ramips

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-11-25 19:48:39 +01:00
Koen Vandeputte
62ede4f783 kernel: bump 4.9 to 4.9.63
Refreshed all patches.

Removed upstreamed parts.

Compile-tested: cns3xxx, imx6, mvebu, layerscape
Run-tested: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-11-22 20:45:52 +01:00
Paul Wassi
e3c55dbe30 ar71xx: merge mach-files for TP-Link TL-WR802N v1 and v2
TP-Link TL-WR802N v1 and v2 are set up with almost same configuration in
the mach-files. Merge the mach-files of these devices.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Tim Thorpe
673793d753 ar71xx: add support for TP-Link TL-WR1043N v5
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option.

The software is more in line with the Archer series in that it uses a
nested bootloader scheme.

Specifications:

 - QCA9563 at 775 MHz
 - 64 MB RAM
 - 16 MB flash
 - 3 (non-detachable) Antennas / 450 Mbit
 - 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
 - reset and Wi-Fi buttons

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2017-11-14 22:36:46 +01:00
Paul Wassi
e202a8b9f6 ar71xx: add support for TP-Link TL-WA901ND v5
The TL-WA901ND v5 has the same hardware as v4, although the PCB has
a different layout. Installation from factory is done via TFTP.
(rename -factory image to wa901ndv4_tp_recovery.bin for tftp)

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Robert Marko
ac4a52b5c8 ar71xx: complete support for RB mAP 2nD
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD

Specifications:

- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port

This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.

Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.

Installation

1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
   - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
     server within the same subnet of the DHCP range
   - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
     of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 22:36:46 +01:00
Paul Wassi
d7adaceda3 ar71xx: fix network setup for UniFi
The Ubiquiti UniFi APs just have eth0. Until now, the setup script fell
through to the default case and configured the (not present) eth1 as
WAN with DHCP.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Robert Marko
3b15eb06c3 ar71xx: complete support for RB wAP 2nD
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD

Specifications:

- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)

This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.

Installation:

1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
   - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
     server within the same subnet of the DHCP range
   - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
     of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 22:36:46 +01:00
Paul Wassi
b23b0fb28b ar71xx: add support for TP-Link TL-WR810N v2
TP-Link TL-WR810N v2 is a compact Wi-Fi router with two Ethernet ports.

Specification:

- QCA9533 (650 MHz)
- 32 MB RAM
- 8 MB Flash
- 300 Mbps Wi-Fi 2.4 GHz
- 2x 10/100 Mbps Ethernet (eth0, eth1)
- UART on testpads on PCB
- 1x LED (GPIO-controlled)
- 1x reset/WPS button
- 1x slide-switch with 2 GPIO inputs

Flash instructions:

- Flash as regular firmware update in Web UI
- Default: 192.168.0.254 / admin / admin
- Select *-factory.bin

When holding reset button during power-up, U-Boot requests a file
'wr810nv1_tp_recovery.bin' from TFTP server at 192.168.0.66

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
c83bdd094e ar71xx: add support for Wallys DR342
Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342.

Short specification:

- 560/450/225 MHz (CPU/DDR/AHB)
- 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm
- 2x MMCX connectors
- miniPCIe connector with PCIe and USB 2.0 buses
- optional miniSIM slot
- 7x LED, 1x button
- UART, (E)JTAG and LED headers
- 1x DC jack for main power (12-56 V)

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
55c77b3d3c ar71xx: increase kernel partition size for TP-Link RE450 v1
This increases kernel partition size and fixes rootfs (file-system)
partition size on TP-Link RE450 v1. Also, while we are at it, switch
from statically defined kernel and rootfs partitions in kernel cmdline
to "tplink-fw" mtd splitter.

Fixes: FS#1072.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
a4bb13e720 ar71xx: fix typo in Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
2eeb8ac271 ar71xx: image: fix typo in tp-link.mk
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Henryk Heisig
ca6002c0ef ar71xx: increase kernel partition size for some TP-Link boards
This patch increases kernel partition size and re-enables image
generation for below TP-Link boards:

- archer-c58-v1
- archer-c60-v1
- tl-wr902ac-v1
- tl-wr942n-v1

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[commit message and title reworded]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Felix Fietkau
645b163cfc ar71xx: fix regression in 74x164 initialization with 4.9
The memcpy of the init data relies on chip->registers to be initialized,
which only happens later in the code. Move this initialization further
down to make it work.
This was breaking PCIe/USB on some MikroTik RouterBoard devices.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-10 00:53:10 +01:00
Rosen Penev
e555153807 ag71xx: Switch from driver to kernel macro for NAPI_WEIGHT.
NAPI_POLL_WEIGHT was introduced in the kernel for exactly this purpose 5 years ago.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-11-06 16:39:41 +01:00
Felix Fietkau
c078386ae3 ar71xx: only use SPI NOR 4K sectors on smaller flash chips for mikrotik devices
On NOR based Mikrotik devices, 4K sectors significantly slow down
firmware flashing and jffs2 usage. On NAND based devices they may be
necessary to run rbcfg (the boot loader config is often on SPI NOR).

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-06 16:38:28 +01:00
Felix Fietkau
c08293893a kernel: add support for limiting 4K erase sector support based on flash chip size
Some targets need 4K sectors for small flash chips (e.g. some
routerboards, where the entire chip is just one "erase block"), whereas
on other devices 4K sectors lead to horrible flash erase/write
performance.

Set the default limit in the generic kernel configuration to 4 MiB to
ensure that all new platforms don't use 4K sectors for bigger flash
chips. On all existing targets use 16 MiB for now to avoid regressions.
They will be changed individually in follow-up commits.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-06 16:38:25 +01:00
Felix Fietkau
1c68fd6d75 ar71xx: fix section mismatch in TP-Link Archer C7 v4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-05 18:52:14 +01:00
Felix Fietkau
e0d58157d8 ar71xx: fix flash fast read on devices using multiple flash chips
Add a callback to allow the SPI driver to indicate which devices fast
flash read works on.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-05 18:52:12 +01:00
Florian Beier
c4c72a9a42 ar71xx: fix LED config for DIR-869 A1
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.

Behavior of the LED front after this patch is applied:

cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0   -> white LEDs are OFF
255 -> white LEDs are ON

cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0   -> orange LEDs are OFF
255 -> orange LEDs are ON

If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.

Signed-off-by: Florian Beier <beier.florian@gmail.com>
2017-11-03 20:04:52 +01:00
Mathias Kresin
f9311e4070 ar71xx: wzr-hp-ag300h: drop unused wmac led_pin settings
The GPIOs are used for defined LEDs and therefore are ignored/unset in
the ath9k driver since 192f0a3db8. The wireless led led trigger is
added in userspace since e20965811d, which makes the
ap9x_pci_setup_wmac_led_pin() superfluous.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-03 20:04:52 +01:00
Thibaut VARENE
dfa2930988 ar71xx: mach-rbspi: fix 74x164 support
The platform data was missing the num_registers element which is now
mandatory in linux 4.9

Without this patch, the gpio probing would fail with:
gpio gpiochip1: (74x164): tried to insert a GPIO chip with zero lines

Fixes: #1106

Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-11-03 20:04:51 +01:00
Henryk Heisig
e917e51bf9 ar71xx: fix board.bin used by QCA9886 in Archer C58/C59/C60
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-10-27 00:45:32 +02:00
Henryk Heisig
34958c8269 ar71xx: Archer C58/C59/C60 fix qca9886 wireless interface
This commit fix 5GHz wireless interface used in Archer C58/C59/C60v1
and set correctly MAC address on this interface.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-10-26 14:44:08 +02:00
Paul Wassi
080061c1ba ar71xx: fix LED names for GL-AR150
Add the respective colour to the LED's names for the GL-AR150 to be conform
to the kernel. Also add netdev triggers for the LAN and WAN LED.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-10-25 09:22:13 +02:00
Paul Wassi
9f7b897939 ar71xx: base-files: alphabetical reordering
Re-order the cases of base-files/* alphabetically.
Also merge some cases in diag.sh

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-10-25 09:22:13 +02:00
Felix Fietkau
b7ea14150f ar71xx: re-enable 4k sectors for the mikrotik subtargets
On RB91x (and possibly others), there is a small SPI flash to store boot
loader and configuration. It needs 4K sectors to be able to write the
configuration using rbcfg

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-24 13:24:05 +02:00
Felix Fietkau
7c09fa4a74 ar71xx: fix mikrotik routerboard nand driver issues with linux 4.9
The mtd device is now embedded inside the nand chip data structure

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-24 13:24:04 +02:00
Felix Fietkau
65da6f9ca1 ar71xx: fix secondary gpio controller base values
In 4.9, gpio count is rounded up to 32 due to the use of bgpio in the
ath79 gpio controller driver.
Fix base values in mach files to account for that

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-24 13:24:04 +02:00
Julien Dusser
8d9ff6b6f7 ar71xx: lzma loader use LTO
Change the Makefile to use LTO for better code optimisations. Gains are
very low, only 270 bytes saved, but it's only Makefile changes.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2017-10-24 13:24:04 +02:00
Julien Dusser
8c5702f2a0 ar71xx: fix lzma loader performance issues
Some bootloaders set a cache cohenrency to a very slow mode. Use code from
Linux kernel to set it to "Cacheable, noncoherent, write-back, write
allocate".

Perfomance impact is significant on TP-Link EAP245 board, kernel
decompression time fall from 33 seconds to less than 1.

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2017-10-24 13:24:04 +02:00
Hauke Mehrtens
f7a6fd3153 ar71xx: deactivate some boards with too small kernel partitions
This affects the following boards:
 * dr344
 * archer-c58-v1
 * archer-c60-v1
 * tl-wr902ac-v1
 * tl-wr942n-v1
 * ubnt-uap-pro
 * ubnt-unifi-outdoor-plus

The build fails for any of these boards because the resulting kernel
image will not fit into the kernel partition.

When CONFIG_KERNEL_KALLSYMS  is not set it could be that the kernel will
fit onto the board again, this is the case for release images.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-22 23:15:11 +02:00
Hauke Mehrtens
c84b7eaedd ar71xx: use kernel 4.9 by default
Kernel 4.9 support was added about 2 weeks ago and we haven't seen any
major regression so far. This patch was not ported to kernel 4.9, this
needs some additional work:
821-serial-core-add-support-for-boot-console-with-arbitr.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-22 15:22:51 +02:00
Felix Fietkau
9887afb1af ar71xx: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 16:14:19 +02:00
Felix Fietkau
2c9aff289e ar71xx: add support for Nokia WI2A-AC200i
Specifications:
 - SoC: Qualcomm QCA9558 (720 MHz)
 - RAM: 256MB
 - Storage: 1MB NOR, 128 MB NAND flash
 - Ethernet: 1x1000M

Installation:
 1. Connect to serial console on the board
 2. Boot initramfs image over u-boot
 3. Copy image to the device and run sysupgrade

Installation without serial console is not supported at this time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 12:27:42 +02:00
Felix Fietkau
3db529d5cc Revert "ar71xx: Add GRO support to ag71xx"
This reverts commit 13e5e47369.
This commit causes a severe regression in LAN->WAN routing performance
for several devices. This appears to be caused by the extra requirement
to validate the SKB checksum early in the rx path, which the ethernet
hardware does not do

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-17 16:03:11 +02:00
Robert Marko
443abb8ccd ar71xx: add support for Mikrotik RB750P-PBr2
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 4 PoE out)
- Outdoor use ready

This ethernet router is based on the same platform as the hEX PoE lite.

Installation

1. login to the Mikrotik WebUI to backup your licence keys
2. setup a DHCP/BOOTP Server with:
     * DHCP-Option 66 (TFTP server name) pointing to a local TFTP
       Server within the same subnet of the DHCP range
     * DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
       of the to be booted image
3. connect the port labled internet to your local network
4. keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
Server. Login as root/without password to the started LEDE via ssh
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
  * rbcfg set boot_protocol bootp
  * rbcfg set boot_device ethnand
  * rbcfg apply

Open Netinstall and reboot routerboard. Now netinstall sees routerboard
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-10-14 10:48:29 +02:00
Hauke Mehrtens
27f23bac8f ar71xx: fix section mismatches
Fix some section mismatches found with kernel 4.9.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-11 22:36:04 +02:00
Hauke Mehrtens
7bbf4117c6 ar71xx: Add kernel 4.9 support
This add support for kernel 4.9 to the ar71xx target.
It was compile tested with the generic, NAND and mikrotik subtarget.
Multiple members of the community tested it on their boards and did not
report any major problem so far.

Especially the NAND part received some changes to adapt to the new
kernel APIs. The serial driver hack used for the Arduino Yun was not
ported because the kernel changed there a lot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-11 22:32:39 +02:00
Kevin Darbyshire-Bryant
e77fa68f1f kernel: bump 4.4 to 4.4.91
Refresh patches.

Compile-tested for: ar71xx Archer C7 v2
Run-tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2017-10-08 20:51:03 +03:00
Andrey Jr. Melnikov
2cb8f0a4cf ar71xx: Fix NULL pointer dereferece in at803x_link_change_notify()
Check pdata pointer before use to avoid OOPS if dev_get_platdata() return
NULL.

Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
2017-10-07 23:19:15 +02:00
Mathias Kresin
1c4a116a30 ar71xx: add rssileds to WA850RE v1 image
A default rssileds config exists for the TP-Link WA850RE v1 but the
rssiled package is not included by default.

The compressed 17.01.3 image size increases by 3302 bytes which should
be tolerable even for a 4MB flash board.

Fixes: FS#1043

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-07 20:15:03 +02:00
Catrinel Catrinescu
b9c31c44d7 ar71xx: update LED definitions for embedded wireless dorin
Evaluation board 2.2 uses a different status LED pin
The other removed LEDs were never present

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-07 09:20:41 +02:00
Catrinel Catrinescu
cd4b60c329 ar71xx: ew-dorin target moved from legacy to generic
Embedded Wireless Dorin platform moved from legacy to generic

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2017-10-07 09:20:04 +02:00
Felix Fietkau
00ea16557d ar71xx: rework chipidea usb controller patch
Handle AR9344 as well. Disable the EHCI platform device when device mode
is active, to avoid resource conflicts.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2017-10-07 09:18:40 +02:00
Felix Fietkau
f4a6daa5da ar71xx: unify CONFIG_CMDLINE
Booting from jffs2 directly is no longer supported, use
rootfstype=squashfs consistently for all subtargets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-09-28 22:45:39 +02:00
Matthias Schiffer
53839da46e
ar71xx: fix MAC addresses on TP-Link TL-WR1043ND v4
The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.

Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-09-11 19:47:19 +02:00
Rosen Penev
13e5e47369 ar71xx: Add GRO support to ag71xx
On a TL-WN710N, this patch increases iperf performance from ~92.5 to ~93.5 mbps. Keep in mind the WN710N is a 100mbps device. I expect greater numbers from gigabit devices.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-09-11 17:12:42 +02:00
Enrique Giraldo
b8b410fba3 ar71xx: add metadata to wpj344 and wpj558 images
This adds metadata to wpj344 and wpj558 images to prevent loading
firmware of wpj344 into wpj558 and vice versa. This until now was
possible and break the units and had to be recovered from the uboot.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
2017-09-10 22:15:04 +02:00
Enrique Giraldo
71067e3b79 ar71xx: wpj558: remove unused eth1 device and fix MAC address
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
2017-09-10 22:15:04 +02:00
Enrique Giraldo
fefdb1e0b9 ar71xx: add support for COMFAST CF-E355AC
COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9882.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 64MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
[whitespace fixes, ac radio caldata offset fix]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:15:03 +02:00
Piotr Dymacz
90d8c0f0a2 ar71xx: add support for GL.iNet GL-USB150
GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:14:43 +02:00
Daniel Gonzalez Cabanelas
3c97bad0c2 ar71xx: WNDR4300: use the switch LED trigger on the WAN port
The WAN port on the Netgear WNDR4300 router has two LEDs,
amber and green. Use the switch LED trigger to behave as the
rest of the LAN HW controlled LEDs
- Green: 1 Gbps
- Amber: 100/10 Mbps

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2017-09-05 08:43:39 +02:00
Kuang Rufan
69323a0c07 ar71xx: add support for TL-WR1041N(v2) LAN/WAN LEDs.
1. Add support to LAN/WAN LEDs attached to ar8327.
2. Fix the problem that LAN/WAN LEDs does not blink in hardware (auto)
   mode when connected to 10M/100M ethernet.

Signed-off-by: Kuang Rufan <master@a1983.com.cn>
2017-09-04 12:48:23 +02:00
Kevin Darbyshire-Bryant
3435de8c16 kernel: update 4.4 to 4.4.85
Refresh patches

Compile & run tested: ar71xx - Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2017-08-31 19:14:52 +02:00
João Chaínho
61027e3430 ar71xx: fix switch port numbering on RB750r2 and RB750UPr2
This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite).
Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them.

Signed-off-by: João Chaínho <joaochainho@gmail.com>
2017-08-31 19:14:52 +02:00
Hauke Mehrtens
39e8ab17d5 kernel: update kernel 4.4 to version 4.4.79
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-07-28 22:46:26 +02:00
Piotr Dymacz
2ad2946777 ar71xx: image: use tplink-v1-header in place of mktplinkfw-kernel
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
f08f754993 build: move mktplinkfw-combined command to image-commands.mk
We will need "mktplinkfw-combined" command also in the "ramips" target
for new MediaTek based TP-Link devices, with "safeloader" image type.

Also, rename the command to "tplink-v1-header", use "VERSION_DIST"
variable instead of "OpenWrt" and allow passing additional parameters.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
b3cb0e7588 firmware-utils: mktplinkfw: rework combined image option
We use combined option in "mktplinkfw" tool for generating initramfs
kernel images and header for kernel inside "safeloader" image type (in
fact, only for TL-WR1043ND v4 at this moment).

There is also "mktplinkfw-kernel" tool, a stripped-down version, used
only for generating "simple" header, for safeloader image types.

This changes how "mktplinkfw" handles combined images (which then will
allow us to drop the stripped-down version of the tool):

- drop "ignore size" command line option (it was used only for combined
  images anyway)
- don't require "flash layout id" for combined images (we don't need and
  shouldn't limit size of the initramfs kernel and for kernels inside
  safeloader images, the "tplink-safeloader" tool does the size check)
- require kernel address and entry point in command line parameters for
  combined images (consequence of previous point)
- don't include md5 sum and firmware length values in header (they are
  needed only for update from vendor GUI and are ingored in case of
  initramfs and "tplink-safeloader" images)
- drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed

Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to
match introduced changes in "mktplinkfw" tool.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:29:50 +02:00
Piotr Dymacz
0c6165d21a ar71xx: add support for ALFA Network AP121F
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB

Flash instruction (under U-Boot web recovery mode):

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
   wait for first blink of all LEDs (indicates network setup), then keep
   button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:13:55 +02:00
Milan Krstić
4c1ce83548 ag71xx: add support for port mirroring
This exposes hardware port mirroring in ag71xx driver (e.g. TL-WR841ND) via
swconfig API.

Signed-off-by: Milan Krstić <milan.krstic@gmail.com>
2017-07-21 08:10:38 +02:00
Sergey Ryazanov
bf5d86543a ar71xx: use the RB912UAG-{2, 5}HPnD Power LED for diag
The Power LED of RB912UAG-{2,5}HPnD boards can be controlled by sofware,
so use it for diag purposes and make the User LED free for other tasks.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-07-20 19:10:29 +02:00
Sergey Ryazanov
6cad8ee0bd ar71xx: keep the RouterBOARD Power LED in On state
It is quite unexpected behaviour when the Power LED switches off as soon
as the kernel starts booting. So set the default state to 'Keep' for
the Power LEDs of all RouterBOARDs (e.g. RB91x, SXT Lite series, etc.).

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[switch the default state to keep instead of on]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-20 19:10:29 +02:00
Mathias Kresin
e4e984f2a0 treewide: use only board_name function to get name
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.

The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
e0b9ec8e96 treewide: drop target board_name functions
They are not used any longer.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
f12a32630f treewide: use the generic board_name function
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
ac3e05c5d7 treewide: populate boardname and model earlier
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.

Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Alexander Couzens
8c96eb2fdb
ar71xx/image: change unifi UBNT_CHIP to ar7240
Verified by OEM firmware images which contains the same
chip.

Tested-by: Andreas Bräu <ab@andi95.de>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-07-13 23:56:24 +02:00
Matthias Schiffer
16222a1010
ar71xx: set US region code for TP-Link TL-WR710N v1 image
Non-US versions of the TP-Link TL-WR710N v1 don't have a region code so
far, so we can just set US unconditionally.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-12 21:30:08 +02:00
Matthias Schiffer
438dcbfe74
base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.

The list of binaries is also slightly cleaned up and duplicates are
removed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:26:32 +02:00
Piotr Dymacz
9d07d2dc56 ar71xx: image: simplify Meraki MR16 device definition
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:46:53 +02:00
Enrique Giraldo
afcf5f69be ar71xx: fix upgrade platform check for Compex WPJ558
The magic number was wrong and always marked the images as invalid.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
2017-07-09 23:46:30 +02:00
Piotr Dymacz
befc763ed1 ar71xx: support LED in TP-Link TL-WR902AC RJ45 socket
TP-Link TL-WR902AC has another one, tiny LED inside RJ45 socket which is
attached to GPIO15. Add support for it, use it as a "lan" LED and rename
old one to "internet". Also, fix uci option name for "lan" LED in system
configuration ("wan" -> "lan").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:44:20 +02:00
Piotr Dymacz
42c8bbb69b ar71xx: verify TP-Link TL-WR902AC sysupgrade image
Until we enable requirement for metadata in sysupgrade images under
ar71xx target, this prevents users from using wrong image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:43:46 +02:00
Henryk Heisig
096a604df0 ar71xx: add metadata to some TP-Link images
This commit adds metadata to TP-Link sysupgrade images
created by tplink-safeloader with uImage kernel header.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-07-09 22:45:59 +02:00
Piotr Dymacz
cf23547e57 ar71xx: fix TPLINK_BOARD_ID for Archer C58 and TL-WA855RE
Rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID for two ommited devices.

Fixes: 7d6c63d ("build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 15:09:52 +02:00
Qian Zheng
a08ec9a54d ar71xx: fix Netgear WNDR3700 v4 switch port mapping
Signed-off-by: Qian Zheng <sotux82@gmail.com>
2017-07-04 11:42:33 +02:00
Piotr Dymacz
6165e4aab0 ar71xx: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

Root access over serial line in vendor firmware: root/sohoadmin.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
0a2e4204db ar71xx: generic: enable CONFIG_MTD_SPLIT_TPLINK_FW
We can use "tplink-fw" mtd splitter for TP-Link devices which use kernel
with TP-Link header embedded inside "safeloader" image type and thus get
rid of statically defined "kernel" and "rootfs" partitions in cmdline.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
43ae7dcdd4 ar71xx: refresh and cleanup mikrotik subtarget kernel config
Refresh mikrotik subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
f67ad17d19 ar71xx: refresh and cleanup nand subtarget kernel config
Refresh nand subtarget kernel config and enable kernel support for
boards which belong to this subtarget only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Piotr Dymacz
cc9b9c5885 ar71xx: refresh and cleanup target kernel config
Refresh target kernel config and disable kernel support for all boards
which belong to nand and mikrotik subtargets only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Jo-Philipp Wich
28cb6ed949 ar71xx: fix typo in network defaults
Commit 9fec39a (ar71xx: add support for TP-Link TL-WA855RE v1) introduced a
typo in 02_network, fix it by removing the stray paren.

Reported-by: Henryk Heisig <hyniu@o2.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-06-29 18:04:29 +02:00
Piotr Dymacz
a73471dea7 ar71xx: image: specify TPLINK_HWID for TP-Link RE450
TPLINK_HWID hasn't been specified for TP-Link RE450 since the begin.
As we don't want to break sysupgrade (all existing LEDE release images
for this board have TPLINK_HWID set to 0x0), set it explicitly to 0x0.

Fixes FS#852

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:46:08 +02:00
Piotr Dymacz
7d6c63d875 build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
ad8c315812 ar71xx: fix switch port mapping for TP-Link TL-WR74xN/D series
Fixes FS#843

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Henryk Heisig
b05c7193fd ar71xx: add support for TP-Link Archer C58 v1
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-06-29 10:37:36 +02:00
Federico Cappon
9fec39a033 ar71xx: add support for TP-Link TL-WA855RE v1
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Federico Cappon <dududede371@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
656ed7544f ar71xx: fix EnGenius ENS202EXT mtd definition
Use statically defined sizes for kernel and rootfs mtd partitions.
Vendor upgrade script writes both firmware parts independently which
ends up in a gap between kernel and rootfs images. This results in
incorrectly calculated rootfs_data start offset.

Also, fix IMAGE_SIZE, DEVICE_PACKAGES and drop redundant KERNEL
definition.

Fixes FS#835

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Camille Bilodeau
bb46b635df ar71xx: move Arduino Yun to generic building code
Migrate Arduino Yun from legacy to generic building code.

Note: the mtd partitioning is changed to adopt the LEDE default
partitioning. It allows to have a kernel bigger than 1280k. It is
necessary as kernel > 4.4 with default LEDE configuration grows
bigger.

To use the new partitioning, you need to update your U-Boot env in
advance:

setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
saveenv

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Camille Bilodeau
2fa58a8d7c ar71xx: remove Arduino Yun 8 MiB prototype
The Arduino Yun has 16 MiB flash. Early prototype boards with 8 MiB were
not available for sell:

https://blog.arduino.cc/2013/08/21/updating-about-arduino-yun-and-arduino-robot/

Signed-off-by: Camille Bilodeau <camille.bilodeau@protonmail.com>
2017-06-29 10:37:36 +02:00
Leon M. George
3e12ca2355 ar71xx: wpj344: set MAC on wan
Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-06-29 10:37:36 +02:00
Leon M. George
98c5a71dfd ar71xx: wpj344: remove unused eth1 device
Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-06-29 10:37:36 +02:00
Leon M. George
c777fd8a7e ar71xx: wpj344: read MAC addresses from u-boot mtd
This way, the assigned addresses match those on the barcode labels.
Otherwise, the addresses appear to vary on boot.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-06-29 10:37:36 +02:00
Stijn Tintel
880f73c327 kernel: cleanup CONFIG_SCHED_HRTICK
Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the
generic config in b47fd76563.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-29 04:46:59 +02:00
Stijn Tintel
f80963d4d1 kernel: update kernel 4.4 to 4.4.74
Refresh patches.
Compile-tested on ar71xx.
Runtime-tested on ar71xx.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-27 07:42:50 +02:00
Alexander Couzens
d98cafc7b6
ar71xx/images/senao: fix reproducible issue using tar
Use deterministic sorting
Use numeric owner/group
Set uid/gid to 0

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-25 12:14:26 +02:00
Alexander Couzens
d6331d5583 ar71xx/image: make tar calls reproducible
Use --mtime when SOURCE_DATE_EPOCH is set.
Use gzip -n9z instead of tar z to remove
timestamp in gzip header.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2017-06-25 12:11:41 +02:00
Mathias Kresin
e7cd6f5d66 ar71xx: add AVM FRITZ!WLAN Repeater 300E support
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
0605b15be4 ar71xx: add AR724x PCIe init fixes
Add upstream send AR724x PCIe patches to get the PCIe controller out of
reset during driver init.

The AVM Fritz 300E bootloader doesn't take care of releasing the
different PCIe controller related resets which causes an endless hang
as soon as either the PCIE Reset register (0x180f0018) or the PCI
Application Control register (0x180f0000) is read from.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Piotr Dymacz
3ff31586eb ar71xx: image: simplify TP-Link devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
8b556fb056 ar71xx: image: fix TP-Link TL-WR710N v2/v2.1 BOARDNAME
All TP-Link TL-WR710N versions share the same machine code.

This has been working since the beginning as we don't use double-quotes
to protect spaces inside command line values. Thus, kernel interprets
'board=TL-WR710N v2' as 'board=TL-WR710N' and separate parameter 'v2'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
7efe0cd83d ar71xx: image: tp-link.mk: keep devices in alphabetical order
Keep TP-Link devices definitions in alphabetical order whenever it's
possible. Also group together similar devices or devices from the same
series.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
a41f38e61d ar71xx: base-files: cleanups in 10-ar922x-led-fix
Fix code style, indentation and leading/trailing whitespaces in:
/etc/hotplug.d/net/10-ar922x-led-fix

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Piotr Dymacz
b73cb365d5 ar71xx: base-files: cleanups in 11-ath10k-caldata
Fix code style and boards alphabetical order in:
/etc/hotplug.d/firmware/11-ath10k-caldata

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Ludwig Thomeczek
b4711dbad3 ar71xx: add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[minor code style fixes, boards alphabetical order fixes,
reworked commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00
Serg Studzinskii
b7cc661615 ar71xx: add support for TP-Link TL-WR942N v1
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*

* Serial console is disabled in OEM non-beta firmwares and corresponding
  GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
  production (non-beta) U-Boot and firmware.

Currently not working:

1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
   by some U-Boot versions.

Flash instruction under vendor GUI:

1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.

FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):

1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
   it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
   turns on.

Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):

1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
   tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
   erase 0x9f020000 +$filesize
   cp.b 0x81000000 0x9f020000 $filesize
   reset

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
641af0c39d ar71xx: move WRTnode2Q to generic build target
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
636ae9e9a0 ar71xx: image: simplify Ubiquiti devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
01aa23acf7 ar71xx: image: mikrotik: shorten DEVICE_TITLE
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
7bc5571d14 ar71xx: image: use simply expanded variables
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:17 +02:00
Piotr Dymacz
80136e57a4 ar71xx: image: update GL.iNet boards DEVICE_TITLE
Use "GL.iNet" as vendor name (based on information from the vendor, this
is registered name of the company) and align model names with official
website.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:31:25 +02:00
Piotr Dymacz
93198b8335 ar71xx: image: fix 8devices boards DEVICE_TITLE
Be consistent with DEVICE_TITLE syntax and use vendor + board names.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:30:05 +02:00
Piotr Dymacz
bd92a6cf57 ar71xx: image: drop unused mtdlayouts from legacy.mk
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00
Piotr Dymacz
708cc2bd3c ar71xx: image: cosmetic: drop redundant empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:22:46 +02:00