Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qusb_phy node looks for the following supply:
"vdd", "vdda-pll", "vdda-phy-dpdm"
And ssphy node looks for the following supply:
"vdda-phy", "vdda-pll"
So fix the usb regulator supply for RT-AX89X.
Fixes: 1306237 ("qualcommax: use PHY regulator for USB GPIO")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17290
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PHY can handle turning off the GPIOs when turning off all USB ports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17192
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17230
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.
Link: https://github.com/openwrt/openwrt/pull/17203
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linksys MR7350 is a 802.11ax Dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz
* RAM: 512MB of DDR3
* Storage: 256Mb NAND
* Ethernet: 5x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate
* LED-s:
* RGB system led
* USB blue led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition:
fw_printenv -n boot_part
- Change the partition:
fw_setenv boot_part 1
or
fw_setenv boot_part 2
depending on the current partition
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel
Co-Authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Co-Authored-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vladyslav Andreichykov <vladdrako007@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace regulator consumer is rather usefull so enable it for ipq60xx
as well and remove from ipq807x only kernel config.
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000 1.5GHz
RAM: NTCC256M16ER-EK 512MiB
Flash: W29N01HZSINA 128MiB
ETH: QCA8075 (3x LAN, 1x WAN)
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Power: DC 12V 1.5A
Button: Reset, Wps
USB: 1x 2.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
Its been a while since we added ipq60xx as source-only, it is now
quite usable so lets remove the source-only flag to start building
official images.
I also plan to merge additional popular boards rather soon.
Link: https://github.com/openwrt/openwrt/pull/17065
Signed-off-by: Robert Marko <robimarko@gmail.com>
These get dynamically set based on compiler version. Not relevant for
targets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol is no longer present.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
Alphabetically sort devices in platform.sh
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that despite NSS not being supported in OpenWrt the memory it
usually uses needs to be reserved anyway for stability reasons.
Link: https://github.com/openwrt/openwrt/pull/16928
Signed-off-by: Robert Marko <robimarko@gmail.com>
Before this commit, sysupgrade saved the settings backup data to
the area following rootfs even though the device has an actual
rootfs_data partition. The backup data was completely ignored on
the following boot, but since rootfs_data was not being cleared
during sysupgrade, the issue was not noticed earlier.
Note that this commit changes the filesystem of rootfs_data from
ext4 to F2FS (if OEM partitioning is used).
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16463
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 2200MHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: QCA8081 (10/100/1000/2.5GBASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2,
and 3 respectively. Be sure to crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.10.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap660hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: George Witt <george.witt@nltsproject.org>
Link: https://github.com/openwrt/openwrt/pull/15832
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cambium Networks XE3-4 is a tri-radio Wi-Fi 6/6E 4×4/2×2 AP.
Hardware:
Model: Cambium Networks XE3-4
CPU: IPQ6010/AP-CP01-C3, SoC Version: 1.0 @ 800 MHz
Memory: 1 GiB
Flash: 512 MiB Macronix MX30UF2G18AC + W25Q128FW
Ethernet: 1x 1 GbE (QCA8072)
1x 2.5 GbE (QCA8081)
Buttons: 1x Reset
Serial: TX, RX, GND
Baudrate: 115200
Radios: Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 2GHz
Qualcomm Atheros IPQ6018 802.11ax - 2x2 - 5GHz
Qualcomm Atheros QCN9074 802.11ax - 4x4 - 5GHz or 6GHz
BLE 4.1
Power: 32.0W 802.3bt5 PoE++
25.5W 802.3at with USB, BT disabled
Size: 215mm x 215mm
Ports: 1x USB 2.0
Antenna: 6 GHz: 6.29 dBi, Omni 30 dBm
5 GHz: 6.12 dBi, Omni 31 dBm
2.4 GHz: 4.85 dBi, Omni 29 dBm
LEDs: Multi-color status LEDs
Mounting: Wall, ceiling or T-bar
Installation: Serial connection
1. Open the AP to get access to the board. Connect RX, TX and GND.
2. Power on the AP, and short the CS pin of the SPI flash with
one of the APs GND pins.
3. Transfer the initramfs image with TFTP
(Default server IP is 192.168.0.120)
# tftpboot factory.ubi
4. Flash the rootfs partition
# flash rootfs
5. Reboot the AP
# reset
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15633
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Asus RT-AX89X BX revision.
WARNING: Only the BX revision boards (So B1, B2 etc) are supported because
AX revision boards use IPQ8074 v1 SoC which is unsupported.
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53 @ 2.2GHz
* RAM: 1024MB
* Storage: 256MB SLC NAND (Macronix MX30UF2G18AC)
* Ethernet:
* 5x 1G RJ45 ports via QCA8337 switch
* 3x 1G RJ45 ports via internal switch (QCA8075 PHY)
* 1x 10G RJ45 via internal switch (AQR113C PHY)
* 1x 10G SFP+ slot via internal switch
* WLAN:
* 2.4GHz 4x4
* 5GHz 8x8
* 8 external antennas
* USB: 2x USB 3.0 Type-A
* Buttons:
* Power switch
* WPS
* Reset
* Wireless ON/OFF
* LED ON/OFF
LED-s:
* Power
* Wi-Fi
* WAN
* 10G
* SFP+
Power:
* 19.5V via DC jack
Installation instructions:
--------------------------
1. Flash temporary OpenWrt initramfs:
* Flash openwrt-qualcommax-ipq807x-asus_rt-ax89x-initramfs-factory.trx
via the stock firmware.
Administration -> Firmware Upgrade -> Manual Firmware update (Upload)
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
2. Sysupgrade from OpenWrt initramfs:
* Copy openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin to
/tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin of
the running initramfs image.
* Simply sysupgrade -n /tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin
After flashing the device will reboot with OpenWrt initramfs and it can
be accesed via any of the LAN ports via SSH with the usual OpenWrt
default credentials.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X has an external QCA8337 switch that has built-in
internal ethernet PHY-s that are supported by the QCA83XX PHY driver so
lets enable it.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X has an Qualcomm QCA8337 switch used to provide additional
1G copper ports, so lets enable qca8k in order to utilize DSA instead of
relying on SSDK for it.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Asus RT-AX89X is using GPIO bitbanged MDIO on newer HW revisions, so lets
enable it in kernel config.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that newer SSDK is now expecting the switch node to be a subnode
of "ess-instance" node which also contains "num_devices" as the number of
switches as you can also have external switches connected.
Asus RT-AX89X is even more peculiar as its bootloader has a hardcoded path
to enable if on that revision there is an AQR113 connected to port 6 of the
switch.
So, lets move the current switch node under ess-instance as otherwise it
seems that SSDK is having some issues parsing the UNIPHY mode properly as
I am getting the following:
[ 6.981404] _adpt_hppe_instance1_mode_get[3275]:ERROR:port 6 doesn't support port_interface_mode 9
Which should not happen as that port has the mode set to 13.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Exclude additional initramfs image for Netgear RAX120v2 when no
initramfs image are compiled to fix build error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix RAX120v2 PWM Fan controller wrong definition by using a non-existant
kmod and using the wrong compatible for it enabling an external clock
while actually the device use an internal one.
Link: https://github.com/openwrt/openwrt/pull/15796
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Now that SSDK has been updated to use in-kernel SMEM ID-s to identify
the SoC its running on instead of relying on the downstream socinfo.h
header we can move the read_ipq_soc_version_major() function directly to
cpr3-util.c as its the only user of anything from the header and drop it.
Link: https://github.com/openwrt/openwrt/pull/15786
Signed-off-by: Robert Marko <robimarko@gmail.com>
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property
Used git grep -E $'\tgpio = <' to make the changes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions for SXK80
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15732
Signed-off-by: Robert Marko <robimarko@gmail.com>
This router has two rootfs partitions and dualboot is used.
Vendor firmware may swap the rootfs partition location, u-boot append
'ubi.mtd=rootfs' in the end of cmdline. Since we use fixed-partitions,
force boot from the first rootfs partition to avoid boot failure.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15700
Signed-off-by: Robert Marko <robimarko@gmail.com>
The wifi radios on wax620 and wax630 got a random mac
address on boot. So fix this by using ath11k_patch_mac
and give a static mac address from label-mac-device.
Tested and working on wax620 and wax630.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15597
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15580
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)
Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
- 2.4 GHz: Qualcomm QCN5024 4x4
- 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
- Power: (Green and red)
- Front: (Blue, green, red and white)
* Buttons:
- 1x Soft reset
- 1x Sync/WPS
* Power: 12V DC Jack
Installation instructions (Telnet):
-----------------------------------
*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate
1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:
`fw_setenv bootcmd 'env default -a; saveenv; reset'`
5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.
6. Run the following command:
`fw_printenv`
It should look similar to the below:
```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```
**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**
7. Run the following command:
`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`
(This should match what's in the bootcmd variable displayed in step 6)
8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```
9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.
10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1
11. Once OpenWrt has booted, update the bootcmd using the following command:
`fw_setenv bootcmd 'run wrtboot'`
12. Flash the sysupgrade image
13. It should boot into OpenWrt
References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip
Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that on Spectrum SAX1V1K QCA8081 is being brought out of reset
too quickly and thus causing it to get stuck in an invalid autoneg
register configuration mode.
Setting an deasset delay seems to fix this, so lets set it.
Fixes: #15493
Link: https://github.com/openwrt/openwrt/pull/15541
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define common Linksys MX device for MX4200v1/v2 and MX5300.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove gpio16 from the default NAND pinctrl configuration
as its unused and only needed for LCD.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
There was no config in the uboot-envtools package, so there is no
generated /etc/fw_env.config for the fw_printenv and fw_setenv utils.
Since uboot-envtools 2024.01, there is a way to make these utils work
without /etc/fw_env.config if the DT has an env partition with the prop.:
compatible = "u-boot,env";
So, this commit adds the prop. above to the appsblenv:0 partition
in the yuncore ax880 DTS file.
Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15305
Signed-off-by: Robert Marko <robimarko@gmail.com>
ipq60xx bootcount script include /lib/functions that produce warning
when the script is enabled on image compilation. This script is already
included by /etc/rc.common hence it's not needed.
While at it also fix the format of the switch case.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
For this particualar device we get random MAC's for Wifi on each (re-)boot.
This is because art partition/pre caldata do not contain valid MAC addresses.
As we have now a new/better approach with ath11k_patch_mac we can use it for
this device too.
I'm using this approach for like two weeks and its working flawlessly.
Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
qualcommax: IPQ807x: ZyXEL NBG7815: Fix random Wifi MAC
Changing order to 3/phy0/5G-1, 2/phy1/2G, 4/phy2/5G-2.
Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
Use ath11k_patch_mac and ath11k_set_macflag functions for RAX120v2 (pre-caldata does not contain valid MAC addresses)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Use ath11k_patch_mac, ath11k_remove_regdomain and ath11k_set_macflag functions for MX4200
(only v2 variant requires MAC patching)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Spectrum SAX1V1K is a AX WIFI router with 3 1G and 1 2.5G ports.
The router is provided to Spectrum customers.
It is OEM of Askey RT5010W
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923
It continues the original work by @MeisterLone to get this device supported.
Specifications:
```
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 2048MB of DDR3
• Storage: 1024MB eMMC
• Ethernet: 3x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
• 2.4GHz: Qualcomm QCN5024 4x4 802.11b/g/n/ax 1174 Mbps PHY rate
• 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• LED: 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x reset
• Power: 12V DC jack
```
Notes:
```
• This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
• Installation can be done by serial connection only.
• A poulated serial header is onboard
https://forum.openwrt.org/t/spectrum-sax1v1k-askey-rt5010w-openwrt-support/149923/6
• RX/TX is working, u-boot bootwait is active, secure boot is enabled.
```
Installation Instructions:
**Most part of the installation is performed from an initramfs image.**
Boot initramfs : Using serial connection
1. Boot up the device and wait till it displays "VERIFY_IB: Success. verify IB ok"
2. Once that message appears,
login with username 'root'
password serial number of your router in uppercase.
3. Use vi to paste the 'open.sh' script from @MeisterLone github on your device
https://github.com/MeisterLone/Askey-RT5010W-D187-REV6/blob/master/Patch/open.sh
4. chmod 755 open.sh
5. ./open.sh
6. Set your ip to 192.168.0.1
7. Run a TFTP server and host the initramfs image on the TFTP server and name it "recovery.img"
8. Reboot device. On boot it will try TFTP.
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Flash firmware: sysupgrade
# sysupgrade -n -v /tmp/openwrt_sysupgrade.bin
4. Set U-boot env variable: bootcmd
# fw_setenv bootcmd "run fix_uboot; run setup_and_boot"
5. Reboot the device
# reboot
6. Once device is booted, residue of previous firmware will prevent openwrt to work properly.
Factory Reset is MUST required
# Once serial console is displaying to login, hold reset button for 10 sec
7. Now everything should be operational.
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Connor Yoon <j_connor@taliaent.com>
