Commit Graph

3754 Commits

Author SHA1 Message Date
Tomasz Maciej Nowak
8b4109c2b4 ar71xx: sysupgrade: accept ath79 combined-image
There is md5 sum of whole image embedded in combined-image header which
is checked on sysupgrade. The check will fail for ath79 images which
may have embedded metadata. This is because metadata are appended after
the combined image is created. To allow smooth transition from ar71xx to
ath79, strip metadata before calculating md5 sum for whole image.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-09-01 00:12:02 +02:00
Michal Cieslakiewicz
dddb43775f ar71xx: WNR2200: remove redundant GPIO for WLAN LED
Without this patch, an extra entry appears for AR9287 GPIO
that duplicates WLAN LED but in fact drives nothing:

gpiochip1: GPIOs 502-511, ath9k-phy0:
 gpio-502 (                    |netgear:blue:wlan   ) out hi
 gpio-503 (                    |netgear:amber:test  ) out hi
 gpio-504 (                    |netgear:green:power ) out lo
 gpio-505 (                    |rfkill              ) in  hi
 gpio-507 (                    |wps                 ) in  hi
 gpio-508 (                    |reset               ) in  hi
 gpio-510 (                    |ath9k-phy0          ) out hi <===!

The pin pointed above is default LED GPIO (8) for AR9287.
For WNR2200 it is not connected anywhere - pin 0 drives blue WLAN
LED instead - but initialization code is missing that information.

This fix calls ap9x_pci_setup_wmac_led_pin() function at device
setup, forcing WLAN LED pin to be 0 and removing redundant entry.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-08-31 12:08:23 +02:00
Koen Vandeputte
81d0da1186 ar71xx/ath79: ag71xx: dont fetch the same var again
tx_size was just declared above and set to BIT(tx->order)
Use the declaration instead, which could avoid a pointer deref

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e773838813 ar71xx: ag71xx: use base address value directly from the source
This brings the code more inline with the ath79 flavour

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
19ed799bdc ar71xx: ag71xx: make use of managed dev API simplifying code
Backport of a4eef43a12 ("ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev")
combined with the initial changes from John Crispin.

Simplifies the code a lot by using the Managed dev API.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
4d40c0edd4 ar71xx: ag71xx: replace ag71xx_get_phy_if_mode_name with phy_modes()
Backport of f73b2d64ed ("ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e18724b907 ar71xx: ag71xx: pass correct device pointer to dma
Backport of 4eaa3626a8 ("ath79: ag71xx: pass correct device pointer to dma functions")

While 4.14 does not contain the warnings,
it still makes sense to use the proper pointers here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
662922068d ar71xx/ath79: ag71xx: get ring_mask consistent
All other instances of this identical declaration fetch the
value directly from the ring_order.

Also do it here.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Koen Vandeputte
e10b163247 ar71xx: ag71xx: add missing register writes
These are added in ath79, but were not backported here

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-27 10:32:44 +02:00
Adrian Schmutzler
b133e466b0
treewide: convert WiFi caldata size and offset to hexadecimal
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.

Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:36:37 +02:00
Adrian Schmutzler
75bfc393ba treewide: convert MAC address location offsets to hexadecimal
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.

(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:10:12 +02:00
Koen Vandeputte
2a08bf3656 ar71xx: ag71xx: init rings with GFP_KERNEL
ar71xx got lost during final rebase ..

Fixes: b417a0c48d ("ar71xx/ath79: ag71xx: init rings with GFP_KERNEL")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-09 18:51:07 +02:00
Koen Vandeputte
6ced31c320 ar71xx/ath79: ag71xx: fix sleep in atomic
When enabling atomic-sleep-debugging options in the kernel,
following splat is seen when disabling the interface (which happens on boot):

[   10.892878] eth0: link down
[   10.896788] BUG: sleeping function called from invalid context at net/core/dev.c:5563
[   10.904730] in_atomic(): 1, irqs_disabled(): 1, pid: 425, name: ip
[   10.911004] 2 locks held by ip/425:
[   10.914539]  #0:  (rtnl_mutex){....}, at: [<80377474>] rtnetlink_rcv_msg+0x2d8/0x380
[   10.922441]  #1:  (&(&ag->lock)->rlock){....}, at: [<80330158>] ag71xx_hw_disable+0x24/0x94
[   10.930976] CPU: 0 PID: 425 Comm: ip Not tainted 4.14.136 #0
[   10.936716] Stack : 805e0000 80589228 80557404 876998ec 80610000 80610000 87cdcafc 805b5327
[   10.945233]         80551534 000001a9 8061386c 87699ccc 87cfb180 00000001 876998a0 84f70903
[   10.953751]         00000000 00000000 80b00000 8769979c 6a7407fa 00000000 00000007 00000000
[   10.962270]         000000b7 16d0954a 000000b6 00000000 80000000 87cb658c 87cb65b0 00000001
[   10.970787]         8046f97c 87699ccc 87cfb180 87ff2810 00000003 802ce724 0806e098 80610000
[   10.979306]         ...
[   10.981797] Call Trace:
[   10.984287] [<8006cb0c>] show_stack+0x58/0x100
[   10.988814] [<800aab34>] ___might_sleep+0x100/0x120
[   10.993774] [<8035c434>] napi_disable+0x30/0xd8
[   10.998377] [<80330198>] ag71xx_hw_disable+0x64/0x94
[   11.003418] [<8033069c>] ag71xx_stop+0x24/0x38
[   11.007959] [<80359e30>] __dev_close_many+0xcc/0x104
[   11.013009] [<80362eac>] __dev_change_flags+0xc8/0x1ac
[   11.018227] [<80362fb8>] dev_change_flags+0x28/0x70
[   11.023182] [<80376890>] do_setlink+0x31c/0x91c
[   11.027786] [<80379360>] rtnl_newlink+0x3ec/0x7f8
[   11.032563] [<80377498>] rtnetlink_rcv_msg+0x2fc/0x380
[   11.037799] [<8039a734>] netlink_rcv_skb+0xd4/0x178
[   11.042754] [<80399d10>] netlink_unicast+0x168/0x250
[   11.047796] [<8039a2d4>] netlink_sendmsg+0x3d8/0x434
[   11.052841] [<8033f0e4>] ___sys_sendmsg+0x1dc/0x290
[   11.057794] [<80340140>] __sys_sendmsg+0x54/0x84
[   11.062495] [<8007212c>] syscall_common+0x34/0x58

This is caused by calling napi_disable() while holding the spinlock.

Fix it by omitting the spinlock, which is not required here
Extensively tested on GL-MiFi, RB-912 and RB-922 hardware

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-09 18:30:41 +02:00
Adrian Schmutzler
8d83a4f545 tplink-safeloader: increase kernel partition for CPE/WBSx10v1
This is a preparation for ath79 support of the CPE210/CPE510 v1.
Kernel size is chosen equal to the latest update for CPE610 v1.

This also updates the partition size in ar71xx target, so code
remains consistent if someone looks up the device. Since CPE210,
CPE510, WBS210 and WBS510 (all v1) share the same partition
layout definition, and are on deprecated target anyway, this
changes them all at once.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-07 18:04:03 +02:00
Leon M. George
c070662980 ar71xx: wpj531: fix SIG1/RSS1 LED GPIO
In commit 6c937df749 ("ar71xx: wpj531: fix GPIOs for LED") wrong GPIO
13 for SIG1/RSS1 LED was commited, the correct GPIO number for this LED
is 12.

It's listed in "Hardware Guide - wpj531 7A06 (02/07/2019)" as GPIO12/RSS1
on the LED header and same GPIO 12 is used in the vendor's SDK as well.

Fixes: 6c937df749 ("ar71xx: wpj531: fix GPIOs for LED")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit subject/message facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-08-04 22:37:15 +02:00
David Bauer
cb49e46a8a ar71xx: fix HiveAP 121 PLL for 1000M
The Aerohive HiveAP 121 has the wrong PLL value set for Gigabit speeds,
leading to packet-loss. 10M and 100M work fine.

This commit sets the Gigabit Ethernet PLL value to the correct value,
fixing packet loss.

Confirmed with iperf and floodping.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-01 21:27:47 +02:00
Koen Vandeputte
845b2a1cfe ar71xx: really fix Mikrotik board detection
commit e09da0169a ("ar71xx: fix Mikrotik board detection")
was generated based on testing a rb-912 board, on which detection failed.

Testing on more hardware shows something fun:

machine	: MikroTik RouterBOARD 922UAGS-5HPacD
machine	: Mikrotik RouterBOARD 912UAG-5HPnD

Both lowercase and uppercase are used.
So ensure we support both now ..

Fixes: e09da0169a ("ar71xx: fix Mikrotik board detection")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-08-01 12:10:02 +02:00
Koen Vandeputte
1d2b2e744e ar71xx: fix nand init issues on some rb2011 devices
While flashing lots of RB2011 devices, I noticed that
some of them refused to boot properly, failing over the NAND parameters.

Checking in detail shows that some device seem to use another NAND flash
which only support standard 2048-byte pages, without 512-byte subpage support.

This commit disables usage of these small subpage completely.

Advantages:
- Both NAND's with(out) subpage support are working now
- The nand speed increases a bit (measured roughly 1%) in typical usecases

Disadvantages:
- The maximum storage capacity decreases by ~0.2%
as small changes can consume a full page (2048 bytes) now.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-07-31 16:53:41 +02:00
Koen Vandeputte
e09da0169a ar71xx: fix Mikrotik board detection
Fix a typo in the machine type being extracted from /proc/cpuinfo
which causes all Mikrotik board to be undetected properly.

This lead to sysupgrade issues and probably some others too.

Fixes: acf2b6c888 ("ar71xx: base-files: fix board detect on new MikroTik devices")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-07-29 10:13:45 +02:00
Tomislav Požega
65762cdd22 ar71xx: fix WLAN LED names for Archer C7
Update WLAN LED colour identifier for both interfaces on Archer C7

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-07-25 07:48:10 +02:00
Tomislav Požega
a73934fc9a ar71xx: fix system LED names on Archer C5/C7
Move system LED board definitions of Archer C5/C7 to reflect
actual system LED colour used

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-07-25 07:48:10 +02:00
Tomislav Požega
c79c001b59 ar71xx: Archer C7 v1 LED names and RFKILL fixes
All leds on these boards are green. v1 has RFKILL GPIO 23 for production
units (it had GPIO 13 only for test phase units, and these are rather
very rare to find). As for the previous attempt to fix this and revert
due to WDR boards have blue leds, it was wrong: WDR board does not use
common setup (false).

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-07-25 07:48:10 +02:00
Tomislav Požega
fd5aa19480 ar71xx: update qca-usb-quirks patch
Base address for USB0 has changed from 0x18116c94 on AR934X
to 0x18116d94 on QCA9558. CP Typo remained for years here...

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
2019-07-25 07:48:10 +02:00
Rafał Miłecki
1cbe0d659c treewide: sysupgrade: get rid of platform_nand_pre_upgrade()
1) nand_do_upgrade() is always called by a target code
2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade()

It means there is no need for the platform_nand_pre_upgrade() callback
at all. All code that was present there could bo moved & simplly called
by a target right before the nand_do_upgrade().

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-22 14:27:37 +02:00
Rafał Miłecki
8b4bc7abe0 treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-17 08:05:38 +02:00
Rafał Miłecki
20452a8db9 ar71xx: get rid of platform_pre_upgrade()
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.

This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-16 19:02:49 +02:00
Etienne Champetier
2a7519e29d ar71xx: enable SGMII fixup on Mikrotik wAP AC
fixes intermittent loss of connectivity on 1Gbit port, with log message:
> 803x_aneg_done: SGMII link is not ok

Thanks to David Bauer for pointing me in the right direction.
I just had to figure out the right bus_id, which you find in this log:
> ag71xx ag71xx.1: connected to PHY at gpio-1:00 [uid=004dd074,
  driver=Atheros 8031 ethernet]

Fixes FS#2236

Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
[Wrapped commit message - Fixed whitespace erors]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-16 16:54:50 +02:00
W. Michael Petullo
8c7d6c47a7 ar71xx: fix ath79/rb4xx IRQ initialization on kernel 4.14
Apply the same approach as in commit 3b53d6fdbc ("ar71xx: fix pci irq
init on kernel 4.14") to fix IRQ initialization for ath79-based chipsets
on rb4xx.

Ref: PR#2182
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: W. Michael Petullo <mike@flyn.org>
[commit ref fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-03 07:45:00 +02:00
Koen Vandeputte
4589f23943 kernel: bump 4.14 to 4.14.129
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-24 16:36:30 +02:00
Koen Vandeputte
1e3487b359 kernel: bump 4.14 to 4.14.127
Refreshed all patches.

Fixes:

- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-18 14:47:53 +02:00
Petr Štetiar
016d1eb1f9 ar71xx: make target source-only
Lets make it really explicit, that we should now focus only on ath79 in
order to make it ready for next release, where ar71xx is going to be
removed for good.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-17 09:42:37 +02:00
Henryk Heisig
acf2b6c888 ar71xx: base-files: fix board detect on new MikroTik devices
Move all MikroTik devices to new function to increase script execution
speed.

Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:

 Old machine name: MikroTik RouterBOARD 951Ui-2nD
 New:              MikroTik RouterBOARD RB951Ui-2nD

So this patch should fix it for all currently supported MikroTik boards.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-17 09:42:37 +02:00
Koen Vandeputte
a7e68927d0 kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)
Refreshed all patches.

This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297

Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch

Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-12 15:04:09 +02:00
Petr Štetiar
971d358579 ar71xx: ag71xx: update ethtool support
Remove references to broken and mostly deprecated phy_ethtool_ioctl, use
new {s,g}et_link_ksettings and add nway_reset which was previously
handled in phy_ethtool_ioctl.

Cc: John Crispin <john@phrozen.org>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=1982
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Petr Štetiar
eafe0611d9 ar71xx: ag71xx: remove unused SIOCETHTOOL ioctl handling
This ioctl is currently routed through generic interface code:

  dev_ioctl
    dev_ethtool
      __ethtool_get_link_ksettings
        phy_ethtool_ioctl

Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:12:30 +02:00
Koen Vandeputte
8f6fd53db9 kernel: bump 4.14 to 4.14.122
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-03 12:40:53 +02:00
Alexander Couzens
8357b8131c
ar71xx: wr940 v4/v6: correct lan interface mac address
The vendor firmware only uses two mac addresses, the mac address on the
label and the label + 1. While checking multiple devices, all labels have
even mac addresses. Concluding only 2 address are assigned to a device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2019-05-21 14:53:45 +02:00
Petr Štetiar
73b21559ce ar71xx: set mib-poll-interval on devices with ar8xxx switch
Commit "generic: ar8216: add mib_poll_interval switch attribute" sets
mib-poll-interval as disabled by default (was set to 2s), so it makes
switch LEDs trigger disfunctional on devices which don't have
mib-poll-interval set.

So this patch sets mib-poll-interval to 500ms on devices which are using
ar8xxx switch LEDs trigger, as the same value was set for built in
switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch").

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-05-20 21:19:48 +02:00
Adrian Schmutzler
f32e05c541 ar71xx: Fix network setup for TP-Link Archer C25 v1
Network for the Archer C25 v1 is set up without switch for no
obvious reason. The LED setup is even done switch-based.

This patch changes network setup so a switch is created.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-15 13:34:24 +02:00
Koen Vandeputte
09050b6fe2 kernel: bump 4.14 to 4.14.118
Refreshed all patches.

Remove upstreamed:
- 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch

Altered:
- 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
Joachim Fünfer
edf1d6264b ar71xx: fix failsafe interface for TL-WR940nv6
Switches failsafe mode interface from WAN to LAN ports.

Tested on TL-WR940Nv6.0 and TL-WR940Nv6.1

Signed-off-by: Joachim Fünfer <joachim.fuenfer@stusta.net>
2019-05-05 21:11:01 +02:00
Rosy Song
3b4c44aa8b ar71xx: mute script error in ar922x-led-fix script
This commit fixes following script error in syslog:

 cat: can't open '/sys/devices/platform/ehci-platform/usb1/1-1/1-1.2/1-1.2:1.4/ieee80211/phy*/name': No such file or directory
 sh: add: unknown operand
 sh: add: unknown operand

Signed-off-by: Rosy Song <rosysong@rosinson.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[commit subject and message tweaks]
2019-05-05 21:11:01 +02:00
Koen Vandeputte
b765f4be40 kernel: bump 4.14 to 4.14.114
Refreshed all patches.

Altered patches:
- 150-bridge_allow_receiption_on_disabled_port.patch
- 201-extra_optimization.patch

Remove upstreamed:
- 022-0006-crypto-crypto4xx-properly-set-IV-after-de-and-encryp.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-02 12:59:26 +02:00
Koen Vandeputte
e40050d104 ar71xx: add support for Mikrotik RouterBOARD 2011UiAS-2HnD r2
This board got a new hardware revision, without any change in functionality.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-23 13:22:31 +02:00
Koen Vandeputte
da5bd73d70 kernel: bump 4.14 to 4.14.112
Refreshed all patches.

New symbol:
- CONFIG_LDISC_AUTOLOAD

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-22 21:15:17 +02:00
Adrian Schmutzler
93d23aced2 ar71xx: Correct MAC address for WAN interface of Archer C7 v5
This device shares the network config with v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.

Based on: https://github.com/openwrt/openwrt/pull/1726

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:05 +02:00
Adrian Schmutzler
9aa8f87d27 ar71xx: Add "info" partition for TP-Link Archer C7 v5
This adds the "info" MTD partition, as it is specified in the
ath79 DTS:
https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35

This is required to set the WAN MAC address, as it is build based
on the LAN MAC address, which in turn has to be read from the
"info" partition:
https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Petr Štetiar
31ea08a64b ar71xx: ag71xx: Fix broken networking on some devices (FS#2177)
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.

Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
0f8cdc28af ar71xx: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
6009b3fd58 ar71xx: ubnt-m-xw: Fix factory image flashing using TFTP recovery
This is backport of the same functionality in ath79, from commit
 d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP
             recovery method")

Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:

 All future airOS versions will be signed in this way and not allow
 unsigned firmware to be loaded except via TFTP.

U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:

 Hit any key to stop autoboot:  0
 Setting default IP 192.168.1.20
 Starting TFTP server...
 Receiving file from 192.168.1.25:38438
 Received 4981148 bytes
 Firmware check failed! (1)

By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:

 Received 3801500 bytes
 Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44
 Setting U-Boot environment variables
 Un-Protected 1 sectors
 Erasing Flash.... done

Patch provided by AREDN[3] project, tested on Bullet M2 XW.

1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00