This adds a missing ";;" in the switch-case in 11-ath10k-caldata.
Fixes: 4d36569b9c ("ath79: fix ath10k caldata extraction on some
D-Link DIR-842 C3 devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
According to forum threads [0][1] and a report on IRC by Doc-Saintly
some of those boards have calibration data in a different place. Only
one alternative location is known.
Without proper board calibration data (board.bin having all 0xff bytes)
ath10k firmware still tries to load but crashes on startup with a
confusing error message.
If you're applying this patch manually on your device do not forget to
remove /lib/firmware/ath10k/pre-cal-pci-0000:00:00.0.bin and reboot to
force caldata re-extraction.
[0] https://forum.openwrt.org/t/support-for-d-link-dir842-rev-c3/41654
[1] https://forum.openwrt.org/t/d-link-dir-842-cant-access-firmware-upload-form/65454
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
All targets that used mvsw61xx have switched to upstream mv88e6xxx DSA
driver, so it can be removed.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: maurerr <mariusd84@gmail.com>
mediatek frequently had mixed indent (tabs vs. spaces) in DTS files
and DTS file kernel patches (probably due to careless copy/paste).
The harmonizes these cases to tabs-only, as usual for DTS(I).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Improve the HDD LEDs used for disk activity:
- Use the trigger activity per ata channel
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
The GPIO base of MT7621 GPIO 0~31 is 480 on kernel 5.4
Fix the GPIO numbering.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: maurerr <mariusd84@gmail.com>
Update dropbear to latest stable 2.81; for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
Both bcm2709 and bcm2710 firmware can run on the same RaspberryPi
models, varying however in 32 and 64 Bit architectures. The model name
alone does not include the architecture information, which becomes
problematic if looking at a overview that only contains the names. By
adding a variant it is possible to tell the architecture.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
BusyBox ip already provides the required functionality and is enabled by default
in OpenWrt. This patch drops the ip dependency and makes the BusyBox ip required
dependencies explicit, allowing for a significant image size reduction.
openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin size:
4588354 bytes (with ip-tiny)
4457282 bytes (with BusyBox ip)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
Apple ships a broken make version with the Xcode command line tools.
Homebrew installs make as gmake by default in order to not collide with
Apple's version.
Exit with an error if the broken one is used accidentally
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: maurerr <mariusd84@gmail.com>
Update iproute2 to latest stable 5.9; for the changes see https://lwn.net/Articles/834755/
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Hauke Mehrtens <hauke@huake-m.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
This pci@40000000 node from upstream was dropped when the device
was converted from local DTS(I) files to kernel patches in [1] to
ensure that change was purely cosmetic.
However, the DK04.1 has a PCI-E slot by default, so let's keep
(i.e. not remove) the kernel definition now.
[1] c4beac9ea2 ("ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1")
Suggested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
A lot of patches are outdated versions of upstreamed patches and
drivers.
So lets pull in the upstreamed patches and reorder remaining ones.
This drops the unnecessary 721-dts-ipq4019-add-ethernet-essedma-node.patch
which adds nodes for not yet in OpenWrt IPQESS driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[do not touch 902-dts-ipq4019-ap-dk04.1.patch here]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
Define wildcard patterns for filtering in target/linux/generic/config-filter
Preparation for supporting newer kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: maurerr <mariusd84@gmail.com>
This will be used to filter out some autogenerated config values from
the kernel config files
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: maurerr <mariusd84@gmail.com>
This replaces the previous (deprecated) method of collecting symvers data
in $(PKG_BUILD_DIR)/Module.symvers, which does not work on newer kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: maurerr <mariusd84@gmail.com>
4a41135750d9 system-linux: only overwrite dev->present state on check_state for simple devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: maurerr <mariusd84@gmail.com>
MikroTik recently changed again the way they store wlan calibration data
on devices. Prior to this change, ERD calibration data for all available
radios was stored within a single identifier node ("tag" in RouterBoot
parlance).
Recent devices have been seen with calibration (and BDF) data stored in
separate identifiers within LZOR packing for each radio: this patch
addresses this by:
1) ensuring that both variants are properly supported,
2) preserving backward compatibility with existing data consumers,
3) allowing for more than 2 calibration blobs to be exposed via sysfs.
Specifically, before this patch, the driver would provide a single sysfs
file named /sys/firmware/mikrotik/hard_config/wlan_data that contained
whatever calibration data found on the device's flash. After this patch,
when executed on a device that uses the old style storage, this behavior
is unchanged, but when executed on a device that uses new style storage
(for either traditional "ERD" packing or "LZOR" packing), the driver
replaces that single file with a folder containing one or more files
each containing the data encoded within individual identifiers.
As far as OpenWRT is concerned, this means that for devices which are
known to exist with both styles of data storage, a suitable hotplug stub
could look like this for e.g. the second radio:
wdata="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wdata" ] && caldata_sysfsload_from_file "$wdata" 0x8000 0x2f20 ) || \
( [ -d "$wdata" ] && caldata_sysfsload_from_file "$wdata/data_2" 0x0 0x2f20 )
This patch has been tested with LZOR old and new style packing on ipq4019,
and with old style on ath79.
Tested-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Шебанов Алексей <admin@ublaze.ru>
Tested-by: Alen Opačić <subixonfire@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
Backport upstream commits that sync the local kernel header
copies in this library, with up to date copies. These updated
headers ensure that libnetfilter-log users can use current
kernel functionality such as requesting that conntrack
information be appended to nflog events sent to userspace via
the NFULNL_CFG_F_CONNTRACK flag. This functionality has been
available since kernel version 4.4
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
Running the updated checkpatch version with spelling.txt show that
spelling mistakes happen to everyone.
> /target/linux$ fd .*.patch | xargs ../../scripts/checkpatch.pl | rg spell
WARNING: 'usefull' may be misspelled - perhaps 'useful'?
WARNING: 'afecting' may be misspelled - perhaps 'affecting'?
WARNING: 'usefull' may be misspelled - perhaps 'useful'?
WARNING: 'afecting' may be misspelled - perhaps 'affecting'?
WARNING: 'begining' may be misspelled - perhaps 'beginning'?
WARNING: 'superflous' may be misspelled - perhaps 'superfluous'?
WARNING: 'multipe' may be misspelled - perhaps 'multiple'?
WARNING: 'recieves' may be misspelled - perhaps 'receives'?
WARNING: 'retreive' may be misspelled - perhaps 'retrieve'?
WARNING: 'tranfer' may be misspelled - perhaps 'transfer'?
WARNING: 'additonal' may be misspelled - perhaps 'additional'?
WARNING: 'accomodate' may be misspelled - perhaps 'accommodate'?
[...]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
Remove checks for device tree documentation as the OpenWrt tree comes
withouth the ./Documentation folder.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
Checkpatch grown in functionallity and we should make use of that. If
OpenWrt patches should be upstream material they should also be checked
based on upstream checkpatch.pl instead of 2013.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
CONFIG_EFI_VARS has been disabled in
64bit x86 target in 2018 by the following commit
b0a51dab8c
the same reasons apply to Generic target, so
now it's disabled here too.
Leaving it enabled is also blocking compile as
a new symbol was added
EFI_CUSTOM_SSDT_OVERLAYS
that depends from CONFIG_EFI_VARS
and the build system stops and waits for
user input on what to do about it.
The Legacy and Geode targets never
had any EFI_xxx configs enabled so they
don't have this issue
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
This adds support for RTL839x SoCs in the ethernet and switch
drivers of the rtl838x architecture.
Reviewed-by: Andreas Oberritter <obi@saftware.de>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
This change adds the configuration option to build and include
the nft_queue kernel module, which allows traffic to be queued up
to userspace from an nftables rule
Tested-by: Sébastien Delafond sdelafond@gmail.com
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
this patch fixes/improves follows:
- PATTERN_LEN is defined as a macro but unused
- redundant logic in count-up for "ptn"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
The source date epoch is the only reproducible date close to the actual
build date. It can be used for tooling like the firmware wizard to show
the image age.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
Make sure exit value of this script is zero. Or the file won't be deleted.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
On some systems I see the issue that crond dies after a few days.
Simply letting procd respawn the process is a simple safety-net.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: maurerr <mariusd84@gmail.com>
5c36293f06 resolv: Serialize processing in resolv/tst-resolv-txnid-collision
2dfa659a66 resolv: Handle transaction ID collisions in parallel queries (bug 26600)
05c025abca support: Provide a way to clear the RA bit in DNS server responses
f688bcd83d support: Provide a way to reorder responses within the DNS test server
eba0ce6058 Remove __warndecl
5337b2af4b Remove __warn_memset_zero_len [BZ #25399]
c6e794640c aarch64: Add unwind information to _start (bug 26853)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
Add support for the following devices:
- Xiaomi Mi Wi-Fi Router 3G v2
- Xiaomi Mi Router 4A Gigabit Edition
Signed-off-by: Antonis Kanouras <antonis@metadosis.eu>
[add explicit case for 4A, bump PKG_RELEASE,
improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
This device has previously been supported by the image
for Xiaomi Mi Router 3G v2. Since this is not obvious, the
4A is marketed as a new major revision and it also seems to
have a different bootloader, this will be both more tidy and
more helpful for the users.
Apart from that, note that there also is a 100M version of
the device that uses mt7628 platform, so a specifically named
image will also prevent confusion in this area.
Specifications:
- SoC: MediaTek MT7621
- Flash: 16 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable "power" LED (two-coloured, yellow/blue)
Non-programmable "internet" LED (shows WAN activity)
- Buttons: Reset
Installation:
Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".
Vendor firmware won't accept any serial input until "uart_en" is
set to "1".
Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:
To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'
Then run 'nvram commit' to make the changes permanent.
Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:
'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
--output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
The restool is for Layerscape DPAA2 platforms which are
ARMv8 platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
E600G v2 based on Qualcomm/Atheros QCA9531
Specification:
- 650/600/200 MHz (CPU/DDR/AHB)
- 128/64 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz
- 2 x 10/100 Mbps Ethernet(RJ45)
- 1 x MiniPCI-e
- 1 x SIM (3G/4G)
- 5 x LED , 1 x Button(SW2-Reset Buttun), 1 x power input
- UART(J100) header on PCB(115200 8N1)
E600GAC v2 based on Qualcomm/Atheros QCA9531 + QCA9887
Specification:
- 650/600/200 MHz (CPU/DDR/AHB)
- 128/64 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz
- 1T1R 5 GHz
- 2 x 10/100 Mbps Ethernet(RJ45)
- 6 x LED (one three-color led), 2 x Button(SW2-Reset Buttun),1 x power input
- UART (J100)header on PCB(115200 8N1)
Flash instruction:
1.Using tftp mode with UART connection and original OpenWrt image
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "openwrt-ath79-generic-xxx-squashfs-sysupgrade.bin"
to "firmware.bin" and place it in tftp server directory.
- Connect PC with one of LAN ports, power up the router and press
key "Enter" to access U-Boot CLI.
- Use the following commands to update the device to OpenWrt:
run lfw
- After that the device will reboot and boot to OpenWrt.
- Wait until all LEDs stops flashing and use the router.
2.Using httpd mode with Web UI connection and original OpenWrt image
- Configure PC with static IP 192.168.1.xxx(2-255) and tftp server.
- Connect PC with one of LAN ports,press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
leds flashing.
- Open your browser and enter 192.168.1.1,You will see the upgrade
interface, select "openwrt-ath79-generic-xxx-squashfs-
sysupgrade.bin" and click the upgrade button.
- After that the device will reboot and boot to OpenWrt.
- Wait until all LEDs stops flashing and use the router.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[rearrange in generic.mk, fix one case in 04_led_migration, update
commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
The file lacks executable permissions, which makes it not being applied
during the first boot.
While at it, drop unneeded include.
Signed-off-by: Piotr Jurkiewicz <piotr.jerzy.jurkiewicz@gmail.com>
[do not touch board name handling, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: maurerr <mariusd84@gmail.com>
* noise: take lock when removing handshake entry from table
This is a defense in depth patch backported from upstream to account for any
future issues with list node lifecycles.
* netns: check that route_me_harder packets use the right sk
A test for an issue that goes back to before Linux's git history began. I've
fixed this upstream, but it doesn't look possible to put it into the compat
layer, as it's a core networking problem. But we still test for it in the
netns test and warn on broken kernels.
* qemu: drop build support for rhel 8.2
We now test 8.3+.
* compat: SYM_FUNC_{START,END} were backported to 5.4
* qemu: bump default testing version
The real motivation for this version bump: 5.4.76 made a change that broke our
compat layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: maurerr <mariusd84@gmail.com>
