Now that the issue with WED has been sorted out, re-add support for
multiple PPE to the mtk_eth_soc driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace Aquantia pending LEDs patch with upstream version.
Sadly net maintainers didn't like integrated solution hence we still
need to handle LED restore on reset with custom solution.
Link: https://github.com/openwrt/openwrt/pull/15797
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch for G761 PWM Fan controller support. This is used by
an ipq807x RAX120v2 and have an internal clock that was currently
unconfigured making the device not working.
Link: https://github.com/openwrt/openwrt/pull/15796
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream fix for incorrect ifdeffery and dependency of CONFIG_KEXEC,
which causes compilation errors with the following symbols:
CONFIG_CRASH_CORE=y
CONFIG_KEXEC_CORE=y
CONFIG_CRASH_DUMP=y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
QCA808x does not currently fill in the possible_interfaces.
This leads to Phylink not being aware that it supports 2500Base-X as well
so in cases where it is connected to a DSA switch like MV88E6393 it will
limit that port to phy-mode set in the DTS.
That means that if SGMII is used you are limited to 1G only while if
2500Base-X was set you are limited to 2.5G only.
Populating the possible_interfaces fixes this, so lets backport the patches
from kernel 6.9.
This also includes a backport of the Phylink PHY validation series from
kernel 6.8 that allows the use of possible_interfaces.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
Marvell Amethyst switches use a different SMI GPIO pin setup than other
switches, and since RB5009 uses Amethyst switch and its SMI bus to talk
to QCA8081 lets backport the required fix from kernel 6.9.
Link: https://github.com/openwrt/openwrt/pull/15765
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are some new commits, so refresh and update patches.
Some build warnings have been fixed upstream too.
Add backport target/linux/generic/backport-6.6/722-v6.10-dt-bindings-arm-qcom-ids-Add-SoC-ID-for-IPQ5321.patch.
Removed upstream:
[-] qca-ssdk/patches/101-hsl_phy-add-support-for-detection-PSGMII-PHY-mode.patch
[-] qca-ssdk/patches/201-fix-compile-warnings.patch
List of changes:
2024-04-16 -c451136b- qca-ssdk: strip MRPPE code
2024-06-05 -f455a820- [qca-ssdk]: fix enum-int-mismatch warnings
2024-05-31 -bbfc0fa9- Merge "[qca-ssdk]: update eee status of phydev"
2024-05-31 -adbe9dc5- Merge "[qca-ssdk]: support psgmii and uqsxgmii mode of kernel"
2024-05-31 -d06ca777- Merge "[qca-ssdk]: fix 5G issue with the AQR FW that use 5gbaser for 5G speed"
2024-05-31 -c6f539a5- Merge "qca-ssdk: support mrppe pktedit padding functions"
2024-04-29 -c321e2a9- qca-ssdk: support mrppe pktedit padding functions
2024-05-24 -ee6e201e- qca-ssdk: Fix the big endian compile error
2024-05-15 -8c116bb9- [qca-ssdk]: update eee status of phydev
2024-05-20 -f0341a2c- Merge "qca-ssdk: Enable igmp for PPE MINI profile"
2024-05-16 -44a0ce93- qca-ssdk: Enable igmp for PPE MINI profile
2024-05-15 -8b91bbf6- [qca-ssdk]: support psgmii and uqsxgmii mode of kernel
2024-05-14 -7eec1658- [qca-ssdk]: fix 5G issue with the AQR FW that use 5gbaser for 5G speed
2024-05-12 -b9f5ea0e- [qca-ssdk]: ethtool support, do not change wake-up timer when the requested timer is 0
2024-05-09 -5e2c15ed- Merge "[qca-ssdk]: remove check when mht clock enable"
2024-05-09 -a1563b90- Merge "[qca-ssdk] support new sku IPQ5321"
2024-04-23 -f04b7680- [qca-ssdk]: show unknown status when link down
2024-03-22 -33b91b30- [qca-ssdk]: remove check when mht clock enable
2024-04-29 -b6362f2b- Merge "qca-ssdk:fix bug in marina nptv6 iid cal"
2024-04-29 -097033ae- Merge "[qca-ssdk] support cypress uniphy0 connecting MHT switch port0"
2024-04-24 -d45560fd- qca-ssdk:fix bug in marina nptv6 iid cal
2024-04-24 -7d7a42af- qca-ssdk: enable policer counter on low memory profile
2024-04-18 -e36cf6ea- Merge "[qca-ssdk]: change portvlan egress mode initial value as untouched"
2024-04-18 -27817881- Merge "[qca-ssdk]: update the aqr phy supported ability"
2024-04-18 -5a3a693c- Merge "qca-ssdk:support marina nptv6"
2024-04-16 -129fe9b3- Merge "qca-ssdk: support tunnel fields and innner fields inverse"
2024-01-09 -fc8f6abd- qca-ssdk:support marina nptv6
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15771
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh patches as line numbers changed with newer upstream version
since original backport PR was opened.
Fixes: a5c095c453 ("generic: 6.6: replace (broken) downstream patch with upstream solution")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Our downstream patch "net/core: add optional threading for backlog processing"
has been broken with the switch to Linux 6.6.
Replace it by backporting the now available upstream solution.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15592
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Partially revert commit 98ddfbc56a ("generic: 6.6: backport upstream
commits for mtk_eth_soc") as the commit breaks WED. A better solution to
assign PPE units in case of WED has still to be found.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport an upstream Linux fix to prevent BPF kfunc functions from being
removed during linker optimization when building BTF-enabled vmlinux.
The telltale sign of this occurring is build log warnings (e.g. mips64el):
BTFIDS vmlinux
WARN: resolve_btfids: unresolved symbol bpf_verify_pkcs7_signature
WARN: resolve_btfids: unresolved symbol bpf_lookup_user_key
WARN: resolve_btfids: unresolved symbol bpf_lookup_system_key
WARN: resolve_btfids: unresolved symbol bpf_key_put
WARN: resolve_btfids: unresolved symbol bpf_iter_task_next
WARN: resolve_btfids: unresolved symbol bpf_iter_css_task_new
WARN: resolve_btfids: unresolved symbol bpf_get_file_xattr
WARN: resolve_btfids: unresolved symbol bpf_ct_insert_entry
NM System.map
SORTTAB vmlinux
Link: https://lore.kernel.org/bpf/ZlkoM6%2FPSxVcGM6X@kodidev-ubuntu/
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15697
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport commit fixing detection of SFP modules which has been broken
since Linux 6.4 for some modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In preparation to update to upcoming Linux 6.6.33 move accepted patches
from mediatek target to backport folder, so moving to newer Linux 6.6
releases becomes easier and also other patches on top can be applied
more easily.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch merged upstream for rgmii-id support in stmmac-ipq806x.
This is needed for some device that directly connets PHY to the gmac
port and require rgmii-id phy-modes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport driver from upcoming Linux 6.10 and put a pending fix on top
to make sure the netdev trigger offloading behaves as expected.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches for the MT7530 DSA driver from net-next tree:
cae425cb43fe net: dsa: allow DSA switch drivers to provide their own phylink mac ops
dd0c9855b413 net: dsa: introduce dsa_phylink_to_port()
7c5e37d7ee78 net: dsa: mt7530: simplify core operations
868ff5f4944a net: dsa: mt7530-mdio: read PHY address of switch from device tree
2c606d138518 net: dsa: mt7530: fix port mirroring for MT7988 SoC switch
d59cf049c837 net: dsa: mt7530: fix mirroring frames received on local port
62d6d91db98a net: dsa: mt7530: provide own phylink MAC operations
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport lots upstream changes, many of them fixes, for the mt7530 DSA
driver, similar to how it was done for Linux 6.1 in the previous commit.
The remaining differences compared to the upstream driver are only
the 'slave' -> 'user', 'master' -> 'conduit' language change in DSA
and the rename of 'struct ethtool_eee' to 'struct ethtool_keee' as
well as tree-wide replacement of ethtool_sprintf with ethtool_puts,
all of them do not have any functional impact.
Apart from some minor bug fixes and style improvements the switch
should now behave more conformant when it comes to link-local frames,
and we will again be able to cleanly pick patches from upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 6.6 added dynamic SWIOTLB allocation, but with it also started
allocating 64MB of the SWIOTLB bounce buffer by default which is quite a
lot of memory on most OpenWrt devices.
Luckily in kernel 6.7 arm64 received an optimization that reduces that
default size to 1MB per 1GB of RAM if certain criteria was met.
So in order to reclaim back 63MB of RAM which brought some ipq807x devices
close to OOM under load lets backport the upstream commit.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO
enterprise access point with two Gigabit Ethernet ports and PoE
support.
Hardware highlights:
- CPU: QCA9550 SoC at 720MHz
- RAM: 256MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: QCA9550-internal radio
- Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC
- Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY
- Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY
- PoE: input through Ethernet 1 port
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: SGM706 (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- eth1 = label MAC + 1
- radio0 (Wi-Fi 5GHz) = label MAC + 2
- radio1 (Wi-Fi 2.4GHz) = label MAC + 3
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script
"run ramboot". Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile
openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot
be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from
non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP5X30XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap5030dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues
-----------------------
- On initial power-up, the Huawei-modified bootloader suspends both
ethernet PHYs (it sets the "Power Down" bit in the MII control
register). Unfortunately, at the time of the initial port, the kernel
driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume
callback defined which would clear this bit. This makes the PHY unusable
since it remains suspended forever. This is why the backported kernel
patches in this commit are required which add this callback and for
completeness also a suspend callback.
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the CPU_CLK/4 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
[fixed 6.6 backport patch naming]
Signed-off-by: David Bauer <mail@david-bauer.net>
It's required to support NAND controllers with WP pin on boards that
don't have it connected to NAND chip.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Also backport most recent MHI modem additions to Linux 6.6.
Adds support for generic SDX75-based modems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
