Commit Graph

1236 Commits

Author SHA1 Message Date
Lech Perczak
6fdeb48c1e ath79: support Ruckus ZoneFlex 7025
Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise
access point with built-in Ethernet switch, in an electrical outlet form factor.

Hardware highligts:
- CPU: Atheros AR7240 SoC at 400 MHz
- RAM: 64MB DDR2
- Flash: 16MB SPI-NOR
- Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio
- Ethernet: single Fast Ethernet port inside the electrical enclosure,
  coupled with internal LSA connector for direct wiring,
  four external Fast Ethernet ports on the lower side of the device.
- PoE: 802.3af PD input inside the electrical box.
  802.3af PSE output on the LAN4 port, capable of sourcing
  class 0 or class 2 devices, depending on power supply capacity.
- External 8P8C pass-through connectors on the back and right side of the device
- Standalone 48V power input on the side, through 2/1mm micro DC barrel jack

Serial console: 115200-8-N-1 on internal JP1 header.
Pinout:

---------- JP1
|5|4|3|2|1|
----------

Pin 1 is near the "H1" marking.
1 - RX
2 - n/c
3 - VCC (3.3V)
4 - GND
5 - TX

Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
  adapter, TFTP server,  and removing a single T10 screw,
  but with much less manual steps, and is generally recommended, being
  safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
  work on some rare versions of stock firmware. A more involved, and
  requires installing `mkenvimage` from u-boot-tools package if you
  choose to rebuild your own environment, but can be used without
  disassembly or removal from installation point, if you have the
  credentials.
  If for some reason, size of your sysupgrade image exceeds 13312kB,
  proceed with method [1]. For official images this is not likely to
  happen ever.

[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
   does not back-power the board, otherwise it will fail to boot.

1. Power-on the board. Then quickly connect serial converter to PC and
   hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
   you'll enter U-boot shell. Then skip to point 3.
   Connection parameters are 115200-8-N-1.

2. Allow the board to boot.  Press the reset button, so the board
   reboots into U-boot again and go back to point 1.

3. Set the "bootcmd" variable to disable the dual-boot feature of the
   system and ensure that uImage is loaded. This is critical step, and
   needs to be done only on initial installation.

   > setenv bootcmd "bootm 0x9f040000"
   > saveenv

4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:

   > setenv serverip 192.168.1.2
   > setenv ipaddr 192.168.1.1
   > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin
   > bootm 0x81000000

5. Optional, but highly recommended: back up contents of "firmware" partition:

   $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin

6. Copy over sysupgrade image, and perform actual installation. OpenWrt
   shall boot from flash afterwards:

   $ ssh root@192.168.1.1
   # sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin

[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
   it boots, hold the reset button near Ethernet connectors for 5
   seconds.

1. Connect the device to the network. It will acquire address over DHCP,
   so either find its address using list of DHCP leases by looking for
   label MAC address, or try finding it by scanning for SSH port:

   $ nmap 10.42.0.0/24 -p22

   From now on, we assume your computer has address 10.42.0.1 and the device
   has address 10.42.0.254.

2. Set up a TFTP server on your computer. We assume that TFTP server
   root is at /srv/tftp.

3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
   frmware is pretty ancient and requires enabling HMAC-MD5.

   $ ssh 10.42.0.254 \
   -o UserKnownHostsFile=/dev/null \
   -o StrictHostKeyCheking=no \
   -o MACs=hmac-md5

   Login. User is "super", password is "sp-admin".
   Now execute a hidden command:

   Ruckus

   It is case-sensitive. Copy and paste the following string,
   including quotes. There will be no output on the console for that.

   ";/bin/sh;"

   Hit "enter". The AP will respond with:

   grrrr
   OK

   Now execute another hidden command:

   !v54!

   At "What's your chow?" prompt just hit "enter".
   Congratulations, you should now be dropped to Busybox shell with root
   permissions.

4. Optional, but highly recommended: backup the flash contents before
   installation. At your PC ensure the device can write the firmware
   over TFTP:

   $ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
   $ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin

   Locate partitions for primary and secondary firmware image.
   NEVER blindly copy over MTD nodes, because MTD indices change
   depending on the currently active firmware, and all partitions are
   writable!

   # grep rcks_wlan /proc/mtd

   Copy over both images using TFTP, this will be useful in case you'd
   like to return to stock FW in future. Make sure to backup both, as
   OpenWrt uses bot firmwre partitions for storage!

   # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1
   # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1

   When the command finishes, copy over the dump to a safe place for
   storage.

   $ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/

5. Ensure the system is running from the BACKUP image, i.e. from
   rcks_wlan.bkup partition or "image 2". Otherwise the installation
   WILL fail, and you will need to access mtd0 device to write image
   which risks overwriting the bootloader, and so is not covered here
   and not supported.

   Switching to backup firmware can be achieved by executing a few
   consecutive reboots of the device, or by updating the stock firmware. The
   system will boot from the image it was not running from previously.
   Stock firmware available to update was conveniently dumped in point 4 :-)

6. Prepare U-boot environment image.
   Install u-boot-tools package. Alternatively, if you build your own
   images, OpenWrt provides mkenvimage in host staging directory as well.
   It is recommended to extract environment from the device, and modify
   it, rather then relying on defaults:

   $ sudo touch /srv/tftp/u-boot-env.bin
   $ sudo chmod 666 /srv/tftp/u-boot-env.bin

   On the device, find the MTD partition on which environment resides.
   Beware, it may change depending on currently active firmware image!

   # grep u-boot-env /proc/mtd

   Now, copy over the partition

   # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1

   Store the stock environment in a safe place:

   $ cp /srv/tftp/u-boot-env.bin ~/

   Extract the values from the dump:

   $ strings u-boot-env.bin | tee u-boot-env.txt

   Now clean up the debris at the end of output, you should end up with
   each variable defined once. After that, set the bootcmd variable like
   this:

   bootcmd=bootm 0x9f040000

   You should end up with something like this:

bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env)
mtdids=nor0=ar7100-nor0
bootdelay=2
filesize=52e000
fileaddr=81000000
ethact=eth0
stdin=serial
stdout=serial
stderr=serial
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=192.168.0.1
serverip=192.168.0.2
stderr=serial
ethact=eth0

   These are the defaults, you can use most likely just this as input to
   mkenvimage.

   Now, create environment image and copy it over to TFTP root:

   $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
   $ sudo cp u-boot-env.bin /srv/tftp

   This is the same image, gzipped and base64-encoded:

H4sICOLMEGMAA3UtYm9vdC1lbnYtbmV3LmJpbgDt0E1u00AUAGDfgm2XDUrTsUV/pTkFSxZoEk+o
lcQJtlNaLsURwU4FikDiBN+3eDNvLL/3Zt5/+vFuud8Pq10dp3V3EV4e1uFDGBXTQeq+9HG1b/v9
NsdheP0Y5mV5U4Vw0Y1f1/3wesix/3pM/dO6v2jaZojX/bJpr6dtsUzHuktDjm//FHl4SnXdxfAS
wmN4SWkMy+UYVqsx1PUYci52Q31I3dDHP5vU3ZUhXLX7LjxWN7eby+PVNNxsflfe3m8uu9Wm//xt
m9rFLjXtv6fLzfEwm5fVfdhc1mlI6342Pytzldvn2dS1qfs49Tjvd3qFOm/Ta6yKdbPNffM9x5sq
Ty805acL3Zfh5HTD1RDHJRT9WLGNfe6atJ2S/XE4y3LX/c6mSzZDs29P3edhmqXOz+1xF//s0y7H
t3GL5nDqWT5Ui/Gii7Aoi7HQ81jrcHZY/dXkfLLiJwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAD8
xy8jb4zOAAAEAA==

7. Perform actual installation. Copy over OpenWrt sysupgrade image to
   TFTP root:

   $ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp

   Now load both to the device over TFTP:

   # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
   # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1

   Verify checksums of both images to ensure the transfer over TFTP
   was completed:

   # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin

   And compare it against source images:

   $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin

   Locate MTD partition of the primary image:

   # grep rcks_wlan.main /proc/mtd

   Now, write the images in place. Write U-boot environment last, so
   unit still can boot from backup image, should power failure occur during
   this. Replace MTD placeholders with real MTD nodes:

   # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
   # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>

   Finally, reboot the device. The device should directly boot into
   OpenWrt. Look for the characteristic power LED blinking pattern.

   # reboot -f

   After unit boots, it should be available at the usual 192.168.1.1/24.

Return to factory firmware:

1. Boot into OpenWrt initramfs as for initial installation. To do that
   without disassembly, you can write an initramfs image to the device
   using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
   fw_setenv bootcmd ""
3. Concatenate the firmware backups, if you took them during installation using method 2:

   $ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin

3. Write factory images downloaded from manufacturer website into
   fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
   before installation:

   # mtd write ruckus_zf7025_backup.bin /dev/mtd1

4. Reboot the system, it should load into factory firmware again.

Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
  partitions for storage using mtd-concat, and uImage format is used to
  actually boot the system, which rules out the dual-boot capability.
- The 2.4 GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
  OpenWrt by choice.
  It is controlled by data in the top 64kB of RAM which is unmapped,
  to avoid   the interference in the boot process and accidental
  switch to the inactive image, although boot script presence in
  form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
  however not much is available in terms of debugging facitilies.
  1. Login to the rkscli
  2. Execute hidden command "Ruckus"
  3. Copy and paste ";/bin/sh;" including quotes. This is required only
     once, the payload will be stored in writable filesystem.
  4. Execute hidden command "!v54!". Press Enter leaving empty reply for
     "What's your chow?" prompt.
  5. Busybox shell shall open.
  Source: https://alephsecurity.com/vulns/aleph-2019014

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-11-13 22:36:06 +01:00
Lech Perczak
a98fa04362 uboot-envtools: ath79: add support for Ubiquiti XM devices
Inspired by commit 9565c5726a, and by
facts that all Ubiquiti XM devices share flash layout, and images are
mostly compatible between all of them - enable uboot-envtools support for
whole XM line.

Build tested on: Ubiquiti Airrouter, Bullet-M (7240,7241), Nanobridge-M,
Nanostation-M (+ Loco), Picostation-M, Powerbridge-M, Rocket-M.
Runtime tested on: Ubiquiti Nanobridge M5 (XM).

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-11-13 22:36:06 +01:00
Mikhail Zhilkin
0cfd15552e ramips: add support for Rostelecom RT-SF-1
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
   Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
   firmware
6. Update firmware using web interface with the OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
    printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+------------+
| use | address    | example    |
+-----+------------+------------+
| LAN | label      | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g  | label + 2  | *:74, *:d4 |
| 5g  | label + 3  | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-13 21:51:22 +01:00
Weiping Yang
9945d05171 ipq40xx: add support for GL.iNet GL-A1300
Specifications:
SOC:		Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:		256 MiB
FLASH1:		4 MiB NOR
FLASH2:		128 MiB NAND
ETH:		Qualcomm QCA8075
WLAN1:		Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:		Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB:		1 x USB 3.0 port
Button:		1 x Reset button
Switch:		1 x Mode switch
LED:		1 x Blue LED + 1 x White LED

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2022-11-09 23:34:37 +01:00
Shiji Yang
f7f9203854 ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based
on Tenbay WR1800K. They have the same hardware circuits and u-boot.
SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile),
SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these
models run the same firmware.

Specifications:
 SOC:      MT7621 + MT7905 + MT7975
 ROM:      128 MiB
 RAM:      256 MiB
 LED:      status *3 R/G/B
 Button:   reset *1 + wps/mesh *1
 Ethernet:      lan *3 + wan *1 (10/100/1000Mbps)
 TTL Baudrate:  115200
 TFTP Server:   192.168.1.254
 TFTP IP:       192.168.1.28 or 192.168.1.160 (when envs is broken)

MAC Address:
 use        address               source
 label      30:xx:xx:xx:xx:62     wan
 lan        30:xx:xx:xx:xx:65     factory.0x8004
 wan        30:xx:xx:xx:xx:62     factory.0x8004 -3
 wlan2g     30:xx:xx:xx:xx:64     factory.0x0004
 wlan5g     32:xx:xx:xx:xx:64     factory.0x0004 set 7th bit

TFTP Installation (initramfs image only & recommend):
1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
   directory of the tftp server. (tftpd64 is a good choice for Windows)
3. Start the TFTP server, plug in the power supply, and wait for the
   system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin", we need
   it to back to stock firmware.
5. Use "fw_printenv" command to list envs.
   If "firmware_select=2" is observed then set u-boot enviroment:
   /# fw_setenv firmware_select 1
6. Apply sysupgrade.bin in OpenWrt LuCI.

Web UI Installation:
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs.
   If "firmware_select=2" is observed then set u-boot enviroment:
   /# fw_setenv firmware_select 1
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.

Recovery to stock firmware:
a. Upload "firmware.bin" to OpenWrt /tmp, then execute:
   /# mtd -r write /tmp/firmware.bin firmware
b. We can also write factory image "UploadBrush-bin.img" to firmware
   partition to recovery. Upload image file to /tmp, then execute:
   /# mtd erase firmware
   /# mtd -r write /tmp/UploadBrush-bin.img firmware

How to extract stock firmware image:
  Download stock firmware, then use openssl:
  openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \
  -out "firmware.tar.tgz" -k QiLunSmartWL

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 22:38:01 +01:00
Pawel Dembicki
d75ed3726d uboot-layerscape: adjust LS1012A-IOT config and env
In a254279a6c LS1012A-IOT kernel image was switched to FIT.

But u-boot config is lack of FIT and ext4 support.

This patch enables it.

It also fix envs, because for some reason this board need to use "loadaddr"
variable in brackets.

Fixes: 
Fixes: a254279a6c ("layerscape: Change to combined rootfs on sd images")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-05 21:12:03 +01:00
Sven Eckelmann
8d3e932b65 uboot-envtools: Fix format of autogenerated sectors
The sector number must be stored in hex. Otherwise, the number (like 16)
will be parsed as hex and any write to the partition will end up with an
error like:

  MTD erase error on /dev/mtd5: Invalid argument

Fixes: 9adfeccd84 ("uboot-envtools: Add support for IPQ806x AP148 and DB149")
Fixes: 54b275c8ed ("ipq40xx: add target")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@fungible.com>
2022-11-01 18:04:38 +01:00
Edward Chow
50f727b773 ath79: add support for Linksys EA4500 v3
Add support for the Linksys EA4500 v3 wireless router

Hardware
--------
SoC:    Qualcomm Atheros QCA9558
RAM:    128M DDR2 (Winbond W971GG6KB-25)
FLASH:  128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN:   QCA9558 3T3R 802.11 bgn
        QCA9580 3T3R 802.11 an
ETH:    Qualcomm Atheros QCA8337
UART:   115200 8n1, same as ea4500 v2
USB:	1 single USB 2.0 host port
BUTTON: Reset - WPS
LED:    1x system-LED
        LEDs besides the ethernet ports are controlled
        by the ethernet switch

MAC Address:
 use        address(sample 1)    source
 label      94:10:3e:xx:xx:6f   caldata@cal_macaddr
 lan        94:10:3e:xx:xx:6f   $label
 wan        94:10:3e:xx:xx:6f   $label
 WiFi4_2G   94:10:3e:xx:xx:70   caldata@cal_ath9k_soc
 WiFi4_5G   94:10:3e:xx:xx:71   caldata@cal_ath9k_pci

Installation from Serial Console
------------

1. Connect to the serial console. Power up the device and interrupt
   autoboot when prompted

2. Connect a TFTP server reachable at 192.168.1.0/24
   (e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
   initramfs image as "openwrt.bin"

3. To test OpenWrt only, go to step 4 and never execute step 5;
   To install, auto_recovery should be disabled first, and boot_part
   should be set to 1 if its current value is not.

   ath> setenv auto_recovery no
   ath> setenv boot_part 1
   ath> saveenv

4. Boot the initramfs image using U-Boot

   ath> setenv serverip 192.168.1.66
   ath> tftpboot 0x84000000 openwrt.bin
   ath> bootm

5. Copy the OpenWrt sysupgrade image to the device using scp and
   install it like a normal upgrade (with no need to keeping config
   since no config from "previous OpenWRT installation" could be kept
   at all)

   # sysupgrade -n /path/to/openwrt/sysupgrade.bin

Note: Like many other routers produced by Linksys, it has a dual
      firmware flash layout, but because I do not know how to handle
      it, I decide to disable it for more usable space. (That is why
      the "auto_recovery" above should be disabled before installing
      OpenWRT.) If someone is interested in generating factory
      firmware image capable to flash from stock firmware, as well as
      restoring the dual firmware layout, commented-out layout for the
      original secondary partitions left in the device tree may be a
      useful hint.

Installation from Web Interface
------------

1. Login to the router via its web interface (default password: admin)

2. Find the firmware update interface under "Connectivity/Basic"

3. Choose the OpenWrt factory image and click "Start"

4. If the router still boots into the stock firmware, it means that
   the OpenWrt factory image has been installed to the secondary
   partitions and failed to boot (since OpenWrt on EA4500 v3 does not
   support dual boot yet), and the router switched back to the stock
   firmware on the primary partitions. You have to install a stock
   firmware (e.g. 3.1.6.172023, downloadable from
   https://www.linksys.com/support-article?articleNum=148385 ) first
   (to the secondary partitions) , and after that, install OpenWrt
   factory image (to the primary partitions). After successful
   installation of OpenWrt, auto_recovery will be automatically
   disabled and router will only boot from the primary partitions.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-10-30 23:14:45 +01:00
Chukun Pan
641e4f2f04 mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128 MB
  RAM: K4A4G165WF-BCWE 512 MB
  Ethernet: 4x 10/100/1000 Mbps
  WiFi1: MT7976GN 2.4GHz ax 4x4
  WiFi2: MT7976AN 5GHz ax 4x4
  Button: Mesh, Reset

Flash instructions:
  1. Gain ssh and serial port access, see the link below:
     https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
  2. Use ssh or serial port to log in to the router, and
     execute the following command:
     nvram set boot_wait=on
     nvram set flag_boot_rootfs=0
     nvram set flag_boot_success=1
     nvram set flag_last_success=1
     nvram set flag_try_sys1_failed=8
     nvram set flag_try_sys2_failed=8
     nvram commit
  3. Set a static ip on the ethernet interface of your computer
     (e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
  4. Download the initramfs image, rename it to initramfs.bin,
     and host it with the tftp server.
  5. Interrupt U-Boot and run these commands:
     setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
     saveenv
     tftpboot initramfs.bin
     bootm
  6. After openwrt boots up, use scp or luci web
     to upload sysupgrade.bin to upgrade.

Revert to stock firmware:
  Restore mtdparts back to default, then use the
  vendor's recovery tool (Windows only).

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-30 14:30:22 +00:00
Nick Hainke
91fa5992bd uboot-envtools: update to 2022.10
Update to latest version.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-10-22 21:10:34 +02:00
Andre Heider
edbf9f156f
uboot-fritz4040: build FritzBox 7520 variant
Support was added as variant of 7530 (DEVICE_ALT0_*) in:
cb6f4be1 "ipq40xx: add support for FRITZ!Box 7520"

u-boot has a distinct config for it [0], built it.

[0] https://github.com/chunkeey/FritzBox-4040-UBOOT/pull/6

Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-10-20 17:42:06 +02:00
Petr Štetiar
0671e78a65 arm-trusted-firmware-sunxi: add package CPE ID
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.

Suggested-by: Steffen Pfendtner <s.pfendtner@ads-tec.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-19 21:40:23 +02:00
Daniel Golle
84b5b0f88c
uboot-envtools: mediatek/mt7622: don't rely on mapped rootfs
Similar to the implementation for the BPi-R3 use the same logic also
for determining the device to look for the U-Boot environment of the
BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-19 20:05:21 +01:00
Daniel Golle
f46355b4d7
uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed
Fix accessing the environment in case no OS is installed on the flash
media selected for boot as this is possible when booting initramfs.
In case of relying on the device specified to be mounted as rootfs to
be present, rather just use the kernel cmdline 'root' variable as a
hint to decide where to read/write the U-Boot environment.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-18 20:08:53 +01:00
Daniel Golle
537b423d9f
uboot-mediatek: update to U-Boot 2022.10
Remove patches adding support for MT7621 which have been merged upsteam.
Patches for MT7981 and MT7986 have been merged too, but not in time to
be included in the 2022.10 release, so we have to keep carrying them
until the 2023.01 release.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-18 20:08:35 +01:00
Robert Marko
b58f3c573d
arm-trusted-firmware-mvebu: add Methode eDPU support
Provide ATF support for Methode eDPU as well, this makes it easy for
OpenWrt users to update the included U-boot+ATF combo.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-17 15:42:50 +02:00
Robert Marko
1324fe468c
uboot-mvebu: add Methode eDPU support
Add support for building for Methode eDPU board, no patches are needed
as board has been upstreamed and is part of the 2022.10-rc releases.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-17 15:42:50 +02:00
Robert Marko
4f348a200b
uboot-mvebu: update to 2022.10
Update mvebu U-boot to 2022.10 to avoid backporting patches in order
to support Methode eDPU.

It also allows dropping existing patches as they are all backports.

Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs
Tested-by: Russell Morris <github@rkmorris.us> # espressobin-v3-v5-1gb-1cs
Tested-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [Turris Omnia]
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2022-10-17 15:42:30 +02:00
Chukun Pan
bb212092df
uboot-mediatek: fixes defconfig typo for UniFi 6 LR
CONFIG_CMD_MTDPART does not exist, fix it.

Fixes: e9ad412 ("uboot-mediatek: add build for Ubiquiti Networks UniFi 6 LR")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-11 14:34:11 +02:00
Chukun Pan
b3c81c9f21
uboot-mediatek: fixes defconfig typo for Linksys E8450
CONFIG_CMD_MTDPART does not exist, fix it.

Fixes: ed50004 ("uboot-mediatek: add support for Linksys E8450")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-11 14:34:07 +02:00
Josef Schlehofer
185541f50f uboot-mvebu: backport LibreSSL patches for older version of LibreSSL
If you would like to compile the newest version of U-boot together with the stable
OpenWrt version, which does not have LibreSSL >= 3.5, which was updated
in the master branch by commit 5451b03b7c
("tools/libressl: bump to v3.5.3"), then you need these two patches to
fix it. They are backported from U-boot repository.

This should be backported to stable OpenWrt versions.

Reported-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-10-02 20:22:54 +02:00
Josef Schlehofer
9c7472950b uboot-mvebu: backport patch to fix compilation on non glibc system
This issue was reported by @paper42, who is using Void Linux with musl
to compile OpenWrt and its packages and found out it is not possible to
compile U-boot for Turris Omnia (neither any other).

It fixes following output:
```
  HOSTCC  tools/kwboot
tools/kwboot.c: In function 'kwboot_tty_change_baudrate':
tools/kwboot.c:662:6: error: 'struct termios' has no member named 'c_ospeed'
  662 |   tio.c_ospeed = tio.c_ispeed = baudrate;
      |      ^
tools/kwboot.c:662:21: error: 'struct termios' has no member named 'c_ispeed'
  662 |   tio.c_ospeed = tio.c_ispeed = baudrate;
      |                     ^
tools/kwboot.c:690:31: error: 'struct termios' has no member named 'c_ospeed'
  690 |  if (!_is_within_tolerance(tio.c_ospeed, baudrate, 3))
      |                               ^
tools/kwboot.c:693:31: error: 'struct termios' has no member named 'c_ispeed'
  693 |  if (!_is_within_tolerance(tio.c_ispeed, baudrate, 3))
      |
```

Tested-by: Michal Vasilek <michal.vasilek@nic.cz>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-10-02 20:22:54 +02:00
Tomasz Maciej Nowak
100536bd37 arm-trusted-firmware-mvebu: stop cluttering Image Builder
All contents of staging_dir/image are included in Image Builder (IB) in
case some binary needs to be included in final image. But in case of
this package, all sources are stored there and those clutter the final
tarball of IB for no reason. Those sources are not used during image
creation and are just dead weight. To put it in perspective, the IB for
21.02.0 is 158 MiB, 22.03.0-rc6 is 366 MiB and snapshot is over 620 MiB!
To fix it, put them in package build directory, so they won't end up
included in IB tarball.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
2022-09-21 13:06:10 +02:00
Alexandru Gagniuc
01e2184c49 realtek: add support for TP-Link SG2210P
Add support for the TP-Link SG2210P switch. This is an RTL8380 based
switch with eight RJ-45 ports with 802.3af PoE, and two SFP ports.

This device shares the same board with the SG2008P and SG2008. To
model this, declare all the capabilities in the sg2xxx dtsi, and
disable unpopulated on the lower end models.

Specifications:
---------------
 - SoC:       Realtek RTL8380M
 - Flash:     32 MiB SPI flash (Vendor varies)
 - RAM:	      256 MiB (Vendor varies)
 - Ethernet:  8x 10/100/1000 Mbps with PoE (all ports)
              2x SFP ports
 - Buttons:   1x "Reset" button on front panel
 - Power:     53.5V DC barrel jack
 - UART:      1x serial header, unpopulated
 - PoE:       2x TI TPS23861 I2C PoE controller

Works:
------
  - (8) RJ-45 ethernet ports
  - (2) SFP ports (with caveats)
  - Switch functions
  - System LED

Not yet enabled:
----------------
  - Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
  - PoE LEDs

Enabling SFP ports:
-------------------

The SFP port control lines are hardwired, except for tx-disable. These
lines are controller by the RTL8231 in shift register mode. There is
no driver support for this yet.

However, to enable the lasers on SFP1 and SFP2 respectively:

    echo 0x0510ff00 > /sys/kernel/debug/rtl838x/led/led_p_en_ctrl
    echo      0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.26
    echo      0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.24

Install via serial console/tftp:
--------------------------------

The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.

The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.

Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWrt:

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"

Power on device, and stop boot by pressing any key.
Once the shell is active:
 1. Ground out the CLK (pin 16) of the ROM (U7)
 2. Select option "3. Start"
 3. Bootloader notes that "The kernel has been damaged!"
 4. Release CLK as sson as bootloader thinks image is corrupted.
 5. Bootloader enters automatic recovery -- details printed on console
 6. Watch as the bootloader flashes and boots OpenWrt.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[OpenWrt capitalisation in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-09-13 09:22:26 +02:00
Petr Štetiar
a575788b8f uboot-mediatek: fix extraneous right parens
Fixes following warning:

 Makefile:310: extraneous text after 'ifeq' directive

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-09-13 09:14:09 +02:00
Yoonji Park
c27279dc26 mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)

Installation:
- Flash recovery image with TFTP recovery

Revert to stock firmware:
- Flash stock firmware with TFTP recovery

TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1

Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
2022-09-12 01:43:49 +01:00
Michael Pratt
5df1b33298 ath79: add support for Senao Watchguard AP100
FCC ID: U2M-CAP2100AG

WatchGuard AP100 is an indoor wireless access point with
1 Gb ethernet port, dual-band but single-radio wireless,
internal antenna plates, and 802.3at PoE+

this board is a Senao device:
the hardware is equivalent to EnGenius EAP300 v2
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails

**Specification:**

  - AR9344 SOC          MIPS 74kc, 2.4 GHz AND 5 GHz WMAC, 2x2
  - AR8035-A EPHY       RGMII GbE with PoE+ IN
  - 25 MHz clock
  - 16 MB FLASH         mx25l12805d
  - 2x 64 MB RAM
  - UART console        J11, populated
  - GPIO watchdog       GPIO 16, 20 sec toggle
  - 2 antennas          5 dBi, internal omni-directional plates
  - 5 LEDs              power, eth0 link/data, 2G, 5G
  - 1 button            reset

**MAC addresses:**

  Label has no MAC
  Only one Vendor MAC address in flash at art 0x0

  eth0 ---- *:e5 art 0x0 -2
  phy0 ---- *:e5 art 0x0 -2

**Installation:**

  Method 1: OEM webpage

    use OEM webpage for firmware upgrade to upload factory.bin

  Method 2: root shell

    It may be necessary to use a Watchguard router to flash the image to the AP
    and / or to downgrade the software on the AP to access SSH
    For some Watchguard devices, serial console over UART is disabled.

  NOTE: DHCP is not enabled by default after flashing

**TFTP recovery:**

  reset button has no function at boot time
  only possible with modified uboot environment,
  (see commit message for Watchguard AP300)

**Return to OEM:**

  user should make backup of MTD partitions
  and write the backups back to mtd devices
  in order to revert to OEM reliably

  It may be possible to use sysupgrade
  with an OEM image as well...
  (not tested)

**OEM upgrade info:**

  The OEM upgrade script is at /etc/fwupgrade.sh

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

**Note on eth0 PLL-data:**

  The default Ethernet Configuration register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For AR934x series, the PLL registers for eth0
  can be see in the DTSI as 0x2c.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x1805002c 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

**Note on WatchGuard Magic string:**

  The OEM upgrade script is a modified version of
  the generic Senao sysupgrade script
  which is used on EnGenius devices.

  On WatchGuard boards produced by Senao,
  images are verified using a md5sum checksum of
  the upgrade image concatenated with a magic string.
  this checksum is then appended to the end of the final image.

  This variable does not apply to all the senao devices
  so set to null string as default

Tested-by: Steve Wheeler <stephenw10@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00
Michael Pratt
9f6e247854 ath79: add support for Senao WatchGuard AP200
FCC ID: U2M-CAP4200AG

WatchGuard AP200 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

this board is a Senao device:
the hardware is equivalent to EnGenius EAP600
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails

**Specification:**

  - AR9344 SOC		MIPS 74kc, 2.4 GHz WMAC, 2x2
  - AR9382 WLAN		PCI card 168c:0030, 5 GHz, 2x2, 26dBm
  - AR8035-A EPHY	RGMII GbE with PoE+ IN
  - 25 MHz clock
  - 16 MB FLASH		mx25l12805d
  - 2x 64 MB RAM
  - UART console        J11, populated
  - GPIO watchdog       GPIO 16, 20 sec toggle
  - 4 antennas          5 dBi, internal omni-directional plates
  - 5 LEDs              power, eth0 link/data, 2G, 5G
  - 1 button            reset

**MAC addresses:**

  Label has no MAC
  Only one Vendor MAC address in flash at art 0x0

  eth0 ---- *:be art 0x0 -2
  phy1 ---- *:bf art 0x0 -1
  phy0 ---- *:be art 0x0 -2

**Installation:**

  Method 1: OEM webpage

    use OEM webpage for firmware upgrade to upload factory.bin

  Method 2: root shell

    It may be necessary to use a Watchguard router to flash the image to the AP
    and / or to downgrade the software on the AP to access SSH
    For some Watchguard devices, serial console over UART is disabled.

  NOTE: DHCP is not enabled by default after flashing

**TFTP recovery:**

  reset button has no function at boot time
  only possible with modified uboot environment,
  (see commit message for Watchguard AP300)

**Return to OEM:**

  user should make backup of MTD partitions
  and write the backups back to mtd devices
  in order to revert to OEM reliably

  It may be possible to use sysupgrade
  with an OEM image as well...
  (not tested)

**OEM upgrade info:**

  The OEM upgrade script is at /etc/fwupgrade.sh

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

**Note on eth0 PLL-data:**

  The default Ethernet Configuration register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For AR934x series, the PLL registers for eth0
  can be see in the DTSI as 0x2c.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x1805002c 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

**Note on WatchGuard Magic string:**

  The OEM upgrade script is a modified version of
  the generic Senao sysupgrade script
  which is used on EnGenius devices.

  On WatchGuard boards produced by Senao,
  images are verified using a md5sum checksum of
  the upgrade image concatenated with a magic string.
  this checksum is then appended to the end of the final image.

  This variable does not apply to all the senao devices
  so set to null string as default

Tested-by: Steve Wheeler <stephenw10@gmail.com>
Tested-by: John Delaney <johnd@ankco.net>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00
Michael Pratt
146aaeafb7 ath79: add support for Senao WatchGuard AP300
FCC ID: Q6G-AP300

WatchGuard AP300 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails

**Specification:**

  - QCA9558 SOC		MIPS 74kc, 2.4 GHz WMAC, 3x3
  - QCA9880 WLAN	PCI card 168c:003c, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 32 MB FLASH		S25FL512S
  - 2x 64 MB RAM	NT5TU32M16
  - UART console	J10, populated
  - GPIO watchdog	GPIO 16, 20 sec toggle
  - 6 antennas		5 dBi, internal omni-directional plates
  - 5 LEDs		power, eth0 link/data, 2G, 5G
  - 1 button		reset

**MAC addresses:**

  MAC address labeled as ETH
  Only one Vendor MAC address in flash at art 0x0

  eth0 ETH  *:3c art 0x0
  phy1 ---- *:3d ---
  phy0 ---- *:3e ---

**Serial console access:**

  For this board, its not certain whether UART is possible
  it is likely that software is blocking console access

  the RX line on the board for UART is shorted to ground by resistor R176
  the resistors R175 and R176 are next to the UART RX pin at J10

  however console output is garbage even after this fix

**Installation:**

  Method 1: OEM webpage

    use OEM webpage for firmware upgrade to upload factory.bin

  Method 2: root shell access

    downgrade XTM firewall to v2.0.0.1
    downgrade AP300 firmware: v1.0.1
    remove / unpair AP from controller
    perform factory reset with reset button
    connect ethernet to a computer
    login to OEM webpage with default address / pass: wgwap
    enable SSHD in OEM webpage settings
    access root shell with SSH as user 'root'
    modify uboot environment to automatically try TFTP at boot time
    (see command below)

    rename initramfs-kernel.bin to test.bin
    load test.bin over TFTP (see TFTP recovery)
    (optionally backup all mtdblocks to have flash backup)
    perform a sysupgrade with sysupgrade.bin

  NOTE: DHCP is not enabled by default after flashing

**TFTP recovery:**

  server ip: 192.168.1.101

  reset button seems to do nothing at boot time...
  only possible with modified uboot environment,
  running this command in the root shell:

  fw_setenv bootcmd 'if ping 192.168.1.101; then tftp 0x82000000 test.bin && bootm 0x82000000; else bootm 0x9f0a0000; fi'

  and verify that it is correct with

  fw_printenv

  then, before boot, the device will attempt TFTP from 192.168.1.101
  looking for file 'test.bin'

  to return uboot environment to normal:

  fw_setenv bootcmd 'bootm 0x9f0a0000'

**Return to OEM:**

  user should make backup of MTD partitions
  and write the backups back to mtd devices
  in order to revert to OEM
  (see installation method 2)

  It may be possible to use sysupgrade
  with an OEM image as well...
  (not tested)

**OEM upgrade info:**

  The OEM upgrade script is at /etc/fwupgrade.sh

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

**Note on eth0 PLL-data:**

  The default Ethernet Configuration register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

**Note on WatchGuard Magic string:**

  The OEM upgrade script is a modified version of
  the generic Senao sysupgrade script
  which is used on EnGenius devices.

  On WatchGuard boards produced by Senao,
  images are verified using a md5sum checksum of
  the upgrade image concatenated with a magic string.
  this checksum is then appended to the end of the final image.

  This variable does not apply to all the senao devices
  so set to null string as default

Tested-by: Alessandro Kornowski <ak@wski.org>
Tested-by: John Wagner <john@wagner.us.org>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-09-11 21:54:00 +02:00
Lech Perczak
f1d112ee5a ath79: support Ruckus ZoneFlex 7321
Ruckus ZoneFlex 7321 is a dual-band, single radio 802.11n 2x2 MIMO enterprise
access point. It is very similar to its bigger brother, ZoneFlex 7372.

Hardware highligts:
- CPU: Atheros AR9342 SoC at 533 MHz
- RAM: 64MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi: AR9342 built-in dual-band 2x2 MIMO radio
- Ethernet: single Gigabit Ethernet port through AR8035 gigabit PHY
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on the 7321-U variant.

Serial console: 115200-8-N-1 on internal H1 header.
Pinout:

H1 ----------
   |1|x3|4|5|
   ----------

Pin 1 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX

JTAG: Connector H5, unpopulated, similar to MIPS eJTAG, standard,
but without the key in pin 12 and not every pin routed:

------- H5
|1 |2 |
-------
|3 |4 |
-------
|5 |6 |
-------
|7 |8 |
-------
|9 |10|
-------
|11|12|
-------
|13|14|
-------

3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected

Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
  adapter, TFTP server,  and removing a single T10 screw,
  but with much less manual steps, and is generally recommended, being
  safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
  work on some rare versions of stock firmware. A more involved, and
  requires installing `mkenvimage` from u-boot-tools package if you
  choose to rebuild your own environment, but can be used without
  disassembly or removal from installation point, if you have the
  credentials.
  If for some reason, size of your sysupgrade image exceeds 13312kB,
  proceed with method [1]. For official images this is not likely to
  happen ever.

[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
   does not back-power the board, otherwise it will fail to boot.

1. Power-on the board. Then quickly connect serial converter to PC and
   hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
   you'll enter U-boot shell. Then skip to point 3.
   Connection parameters are 115200-8-N-1.

2. Allow the board to boot.  Press the reset button, so the board
   reboots into U-boot again and go back to point 1.

3. Set the "bootcmd" variable to disable the dual-boot feature of the
   system and ensure that uImage is loaded. This is critical step, and
   needs to be done only on initial installation.

   > setenv bootcmd "bootm 0x9f040000"
   > saveenv

4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:

   > setenv serverip 192.168.1.2
   > setenv ipaddr 192.168.1.1
   > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7321-initramfs-kernel.bin
   > bootm 0x81000000

5. Optional, but highly recommended: back up contents of "firmware" partition:

   $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7321_fw1_backup.bin
   $ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7321_fw2_backup.bin

6. Copy over sysupgrade image, and perform actual installation. OpenWrt
   shall boot from flash afterwards:

   $ ssh root@192.168.1.1
   # sysupgrade -n openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin

[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
   it boots, hold the reset button near Ethernet connectors for 5
   seconds.

1. Connect the device to the network. It will acquire address over DHCP,
   so either find its address using list of DHCP leases by looking for
   label MAC address, or try finding it by scanning for SSH port:

   $ nmap 10.42.0.0/24 -p22

   From now on, we assume your computer has address 10.42.0.1 and the device
   has address 10.42.0.254.

2. Set up a TFTP server on your computer. We assume that TFTP server
   root is at /srv/tftp.

3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
   frmware is pretty ancient and requires enabling HMAC-MD5.

   $ ssh 10.42.0.254 \
   -o UserKnownHostsFile=/dev/null \
   -o StrictHostKeyCheking=no \
   -o MACs=hmac-md5

   Login. User is "super", password is "sp-admin".
   Now execute a hidden command:

   Ruckus

   It is case-sensitive. Copy and paste the following string,
   including quotes. There will be no output on the console for that.

   ";/bin/sh;"

   Hit "enter". The AP will respond with:

   grrrr
   OK

   Now execute another hidden command:

   !v54!

   At "What's your chow?" prompt just hit "enter".
   Congratulations, you should now be dropped to Busybox shell with root
   permissions.

4. Optional, but highly recommended: backup the flash contents before
   installation. At your PC ensure the device can write the firmware
   over TFTP:

   $ sudo touch /srv/tftp/ruckus_zf7321_firmware{1,2}.bin
   $ sudo chmod 666 /srv/tftp/ruckus_zf7321_firmware{1,2}.bin

   Locate partitions for primary and secondary firmware image.
   NEVER blindly copy over MTD nodes, because MTD indices change
   depending on the currently active firmware, and all partitions are
   writable!

   # grep rcks_wlan /proc/mtd

   Copy over both images using TFTP, this will be useful in case you'd
   like to return to stock FW in future. Make sure to backup both, as
   OpenWrt uses bot firmwre partitions for storage!

   # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7321_firmware1.bin -p 10.42.0.1
   # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7321_firmware2.bin -p 10.42.0.1

   When the command finishes, copy over the dump to a safe place for
   storage.

   $ cp /srv/tftp/ruckus_zf7321_firmware{1,2}.bin ~/

5. Ensure the system is running from the BACKUP image, i.e. from
   rcks_wlan.bkup partition or "image 2". Otherwise the installation
   WILL fail, and you will need to access mtd0 device to write image
   which risks overwriting the bootloader, and so is not covered here
   and not supported.

   Switching to backup firmware can be achieved by executing a few
   consecutive reboots of the device, or by updating the stock firmware. The
   system will boot from the image it was not running from previously.
   Stock firmware available to update was conveniently dumped in point 4 :-)

6. Prepare U-boot environment image.
   Install u-boot-tools package. Alternatively, if you build your own
   images, OpenWrt provides mkenvimage in host staging directory as well.
   It is recommended to extract environment from the device, and modify
   it, rather then relying on defaults:

   $ sudo touch /srv/tftp/u-boot-env.bin
   $ sudo chmod 666 /srv/tftp/u-boot-env.bin

   On the device, find the MTD partition on which environment resides.
   Beware, it may change depending on currently active firmware image!

   # grep u-boot-env /proc/mtd

   Now, copy over the partition

   # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1

   Store the stock environment in a safe place:

   $ cp /srv/tftp/u-boot-env.bin ~/

   Extract the values from the dump:

   $ strings u-boot-env.bin | tee u-boot-env.txt

   Now clean up the debris at the end of output, you should end up with
   each variable defined once. After that, set the bootcmd variable like
   this:

   bootcmd=bootm 0x9f040000

   You should end up with something like this:

bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
mtdids=nor0=ar7100-nor0
bootdelay=2
ethact=eth0
filesize=78a000
fileaddr=81000000
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=10.0.0.1
serverip=10.0.0.5
stdin=serial
stdout=serial
stderr=serial

   These are the defaults, you can use most likely just this as input to
   mkenvimage.

   Now, create environment image and copy it over to TFTP root:

   $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
   $ sudo cp u-boot-env.bin /srv/tftp

   This is the same image, gzipped and base64-encoded:

H4sIAAAAAAAAA+3QQW7TQBQAUF8EKRtQI6XtJDS0VJoN4gYcAE3iCbWS2MF2Sss1ORDYqVq6YMEB3rP0
Z/7Yf+aP3/56827VNP16X8Zx3E/Cw8dNuAqDYlxI7bcurpu6a3Y59v3jlzCbz5eLECbt8HbT9Y+HHLvv
x9TdbbpJVVd9vOxWVX05TotVOpZt6nN8qilyf5fKso3hIYTb8JDSEFarIazXQyjLIeRc7PvykNq+iy+T
1F7PQzivmzbcLpYftmfH87G56Wz+/v18sT1r19vu649dqi/2qaqns0W4utmelalPm27I/lac5/p+OluO
NZ+a1JaTz8M3/9hmtT0epmMjVdnF8djXLZx+TJl36TEuTlda93EYQrGpdrmrfuZ4fZPGHzjmp/vezMNJ
MV6n6qumPm06C+MRZb6vj/v4Mk/7HJ+6LarDqXweLsZnXnS5vc9tdXheWRbd0GIdh/Uq7cakOfavsty2
z1nxGwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAD+1x9eTkHLAAAEAA==

7. Perform actual installation. Copy over OpenWrt sysupgrade image to
   TFTP root:

   $ sudo cp openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin /srv/tftp

   Now load both to the device over TFTP:

   # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
   # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin -g 10.42.0.1

   Vverify checksums of both images to ensure the transfer over TFTP
   was completed:

   # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin

   And compare it against source images:

   $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin

   Locate MTD partition of the primary image:

   # grep rcks_wlan.main /proc/mtd

   Now, write the images in place. Write U-boot environment last, so
   unit still can boot from backup image, should power failure occur during
   this. Replace MTD placeholders with real MTD nodes:

   # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
   # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>

   Finally, reboot the device. The device should directly boot into
   OpenWrt. Look for the characteristic power LED blinking pattern.

   # reboot -f

   After unit boots, it should be available at the usual 192.168.1.1/24.

Return to factory firmware:

1. Boot into OpenWrt initramfs as for initial installation. To do that
   without disassembly, you can write an initramfs image to the device
   using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
   fw_setenv bootcmd ""
3. Write factory images downloaded from manufacturer website into
   fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
   before installation:
   mtd write ruckus_zf7321_fw1_backup.bin /dev/mtd1
   mtd write ruckus_zf7321_fw2_backup.bin /dev/mtd5
4. Reboot the system, it should load into factory firmware again.

Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
  partitions for storage using mtd-concat, and uImage format is used to
  actually boot the system, which rules out the dual-boot capability.
- The 5GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
  OpenWrt by choice.
  It is controlled by data in the top 64kB of RAM which is unmapped,
  to avoid   the interference in the boot process and accidental
  switch to the inactive image, although boot script presence in
  form of "bootcmd" variable should prevent this entirely.
- U-boot disables JTAG when starting. To re-enable it, you need to
  execute the following command before booting:
  mw.l 1804006c 40
  And also you need to disable the reset button in device tree if you
  intend to debug Linux, because reset button on GPIO0 shares the TCK
  pin.
- On some versions of stock firmware, it is possible to obtain root shell,
  however not much is available in terms of debugging facitilies.
  1. Login to the rkscli
  2. Execute hidden command "Ruckus"
  3. Copy and paste ";/bin/sh;" including quotes. This is required only
     once, the payload will be stored in writable filesystem.
  4. Execute hidden command "!v54!". Press Enter leaving empty reply for
     "What's your chow?" prompt.
  5. Busybox shell shall open.
  Source: https://alephsecurity.com/vulns/aleph-2019014

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-09-11 01:36:25 +02:00
Lech Perczak
59cb4dc91d ath79: support Ruckus ZoneFlex 7372
Ruckus ZoneFlex 7372 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise
access point.

Ruckus ZoneFlex 7352 is also supported, lacking the 5GHz radio part.

Hardware highligts:
- CPU: Atheros AR9344 SoC at 560 MHz
- RAM: 128MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: AR9344 built-in 2x2 MIMO radio
- Wi-Fi 5Ghz: AR9582 2x2 MIMO radio (Only in ZF7372)
- Antennas:
  - Separate internal active antennas with beamforming support on both
    bands with 7 elements per band, each controlled by 74LV164 GPIO
    expanders, attached to GPIOs of each radio.
  - Two dual-band external RP-SMA antenna connections on "7372-E"
    variant.
- Ethernet 1: single Gigabit Ethernet port through AR8035 gigabit PHY
- Ethernet 2: single Fast Ethernet port through AR9344 built-in switch
- PoE: input through Gigabit port
- Standalone 12V/1A power input
- USB: optional single USB 2.0 host port on "-U" variants.

The same image should support:
- ZoneFlex 7372E (variant with external antennas, without beamforming
  capability)
- ZoneFlex 7352 (single-band, 2.4GHz-only variant).

which are based on same baseboard (codename St. Bernard),
with different populated components.

Serial console: 115200-8-N-1 on internal H1 header.
Pinout:

H1
---
|5|
---
|4|
---
|3|
---
|x|
---
|1|
---

Pin 5 is near the "H1" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX

JTAG: Connector H2, similar to MIPS eJTAG, standard,
but without the key in pin 12 and not every pin routed:

------- H2
|1 |2 |
-------
|3 |4 |
-------
|5 |6 |
-------
|7 |8 |
-------
|9 |10|
-------
|11|12|
-------
|13|14|
-------

3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected

Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
  adapter, TFTP server,  and removing a single T10 screw,
  but with much less manual steps, and is generally recommended, being
  safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
  work on some rare versions of stock firmware. A more involved, and
  requires installing `mkenvimage` from u-boot-tools package if you
  choose to rebuild your own environment, but can be used without
  disassembly or removal from installation point, if you have the
  credentials.
  If for some reason, size of your sysupgrade image exceeds 13312kB,
  proceed with method [1]. For official images this is not likely to
  happen ever.

[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
   does not back-power the board, otherwise it will fail to boot.

1. Power-on the board. Then quickly connect serial converter to PC and
   hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
   you'll enter U-boot shell. Then skip to point 3.
   Connection parameters are 115200-8-N-1.

2. Allow the board to boot.  Press the reset button, so the board
   reboots into U-boot again and go back to point 1.

3. Set the "bootcmd" variable to disable the dual-boot feature of the
   system and ensure that uImage is loaded. This is critical step, and
   needs to be done only on initial installation.

   > setenv bootcmd "bootm 0x9f040000"
   > saveenv

4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:

   > setenv serverip 192.168.1.2
   > setenv ipaddr 192.168.1.1
   > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7372-initramfs-kernel.bin
   > bootm 0x81000000

5. Optional, but highly recommended: back up contents of "firmware" partition:

   $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7372_fw1_backup.bin
   $ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7372_fw2_backup.bin

6. Copy over sysupgrade image, and perform actual installation. OpenWrt
   shall boot from flash afterwards:

   $ ssh root@192.168.1.1
   # sysupgrade -n openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin

[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
   it boots, hold the reset button near Ethernet connectors for 5
   seconds.

1. Connect the device to the network. It will acquire address over DHCP,
   so either find its address using list of DHCP leases by looking for
   label MAC address, or try finding it by scanning for SSH port:

   $ nmap 10.42.0.0/24 -p22

   From now on, we assume your computer has address 10.42.0.1 and the device
   has address 10.42.0.254.

2. Set up a TFTP server on your computer. We assume that TFTP server
   root is at /srv/tftp.

3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
   frmware is pretty ancient and requires enabling HMAC-MD5.

   $ ssh 10.42.0.254 \
   -o UserKnownHostsFile=/dev/null \
   -o StrictHostKeyCheking=no \
   -o MACs=hmac-md5

   Login. User is "super", password is "sp-admin".
   Now execute a hidden command:

   Ruckus

   It is case-sensitive. Copy and paste the following string,
   including quotes. There will be no output on the console for that.

   ";/bin/sh;"

   Hit "enter". The AP will respond with:

   grrrr
   OK

   Now execute another hidden command:

   !v54!

   At "What's your chow?" prompt just hit "enter".
   Congratulations, you should now be dropped to Busybox shell with root
   permissions.

4. Optional, but highly recommended: backup the flash contents before
   installation. At your PC ensure the device can write the firmware
   over TFTP:

   $ sudo touch /srv/tftp/ruckus_zf7372_firmware{1,2}.bin
   $ sudo chmod 666 /srv/tftp/ruckus_zf7372_firmware{1,2}.bin

   Locate partitions for primary and secondary firmware image.
   NEVER blindly copy over MTD nodes, because MTD indices change
   depending on the currently active firmware, and all partitions are
   writable!

   # grep rcks_wlan /proc/mtd

   Copy over both images using TFTP, this will be useful in case you'd
   like to return to stock FW in future. Make sure to backup both, as
   OpenWrt uses bot firmwre partitions for storage!

   # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7372_firmware1.bin -p 10.42.0.1
   # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7372_firmware2.bin -p 10.42.0.1

   When the command finishes, copy over the dump to a safe place for
   storage.

   $ cp /srv/tftp/ruckus_zf7372_firmware{1,2}.bin ~/

5. Ensure the system is running from the BACKUP image, i.e. from
   rcks_wlan.bkup partition or "image 2". Otherwise the installation
   WILL fail, and you will need to access mtd0 device to write image
   which risks overwriting the bootloader, and so is not covered here
   and not supported.

   Switching to backup firmware can be achieved by executing a few
   consecutive reboots of the device, or by updating the stock firmware. The
   system will boot from the image it was not running from previously.
   Stock firmware available to update was conveniently dumped in point 4 :-)

6. Prepare U-boot environment image.
   Install u-boot-tools package. Alternatively, if you build your own
   images, OpenWrt provides mkenvimage in host staging directory as well.
   It is recommended to extract environment from the device, and modify
   it, rather then relying on defaults:

   $ sudo touch /srv/tftp/u-boot-env.bin
   $ sudo chmod 666 /srv/tftp/u-boot-env.bin

   On the device, find the MTD partition on which environment resides.
   Beware, it may change depending on currently active firmware image!

   # grep u-boot-env /proc/mtd

   Now, copy over the partition

   # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1

   Store the stock environment in a safe place:

   $ cp /srv/tftp/u-boot-env.bin ~/

   Extract the values from the dump:

   $ strings u-boot-env.bin | tee u-boot-env.txt

   Now clean up the debris at the end of output, you should end up with
   each variable defined once. After that, set the bootcmd variable like
   this:

   bootcmd=bootm 0x9f040000

   You should end up with something like this:

bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
bootdelay=2
mtdids=nor0=ar7100-nor0
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
ethact=eth0
filesize=1000000
fileaddr=81000000
ipaddr=192.168.0.7
serverip=192.168.0.51
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
stdin=serial
stdout=serial
stderr=serial

   These are the defaults, you can use most likely just this as input to
   mkenvimage.

   Now, create environment image and copy it over to TFTP root:

   $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
   $ sudo cp u-boot-env.bin /srv/tftp

   This is the same image, gzipped and base64-encoded:

H4sIAAAAAAAAA+3QTW7TQBQAYB+AQ2TZSGk6Tpv+SbNBrNhyADSJHWolsYPtlJaDcAWOCXaqQhdIXOD7
Fm/ee+MZ+/nHu58fV03Tr/dFHNf9JDzdbcJVGGRjI7Vfurhu6q7ZlbHvnz+FWZ4vFyFM2mF30/XPhzJ2
X4+pe9h0k6qu+njRrar6YkyzVToWberL+HImK/uHVBRtDE8h3IenlIawWg1hvR5CUQyhLE/vLcpdeo6L
bN8XVdHFumlDTO1NHsL5mI/9Q2r7Lv5J3uzeL5bX27Pj+XjRdJZfXuaL7Vm73nafv+1SPd+nqp7OFuHq
dntWpD5tuqH6e+K8rB+ns+V45n2T2mLyYXjmH9estsfD9DTSuo/DErJNtSu76vswbjg5NU4D3752qsOp
zu8W8/z6dh7mN1lXto9lWx3eNJd5Ng5V9VVTn2afnSYuysf6uI9/8rQv48s3Z93wn+o4XFWl3Vg0x/5N
Vbbta5X9AgAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAAAAAAAID/+Q2Z/B7cAAAEAA==

7. Perform actual installation. Copy over OpenWrt sysupgrade image to
   TFTP root:

   $ sudo cp openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin /srv/tftp

   Now load both to the device over TFTP:

   # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
   # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin -g 10.42.0.1

   Verify checksums of both images to ensure the transfer over TFTP
   was completed:

   # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin

   And compare it against source images:

   $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin

   Locate MTD partition of the primary image:

   # grep rcks_wlan.main /proc/mtd

   Now, write the images in place. Write U-boot environment last, so
   unit still can boot from backup image, should power failure occur during
   this. Replace MTD placeholders with real MTD nodes:

   # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
   # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>

   Finally, reboot the device. The device should directly boot into
   OpenWrt. Look for the characteristic power LED blinking pattern.

   # reboot -f

   After unit boots, it should be available at the usual 192.168.1.1/24.

Return to factory firmware:

1. Boot into OpenWrt initramfs as for initial installation. To do that
   without disassembly, you can write an initramfs image to the device
   using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
   fw_setenv bootcmd ""
3. Write factory images downloaded from manufacturer website into
   fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
   before installation:
   mtd write ruckus_zf7372_fw1_backup.bin /dev/mtd1
   mtd write ruckus_zf7372_fw2_backup.bin /dev/mtd5
4. Reboot the system, it should load into factory firmware again.

Quirks and known issues:
- This is first device in ath79 target to support link state reporting
  on FE port attached trough the built-in switch.
- Flash layout is changed from the factory, to use both firmware image
  partitions for storage using mtd-concat, and uImage format is used to
  actually boot the system, which rules out the dual-boot capability.
  The 5GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
  OpenWrt by choice.
  It is controlled by data in the top 64kB of RAM which is unmapped,
  to avoid   the interference in the boot process and accidental
  switch to the inactive image, although boot script presence in
  form of "bootcmd" variable should prevent this entirely.
- U-boot disables JTAG when starting. To re-enable it, you need to
  execute the following command before booting:
  mw.l 1804006c 40
  And also you need to disable the reset button in device tree if you
  intend to debug Linux, because reset button on GPIO0 shares the TCK
  pin.
- On some versions of stock firmware, it is possible to obtain root shell,
  however not much is available in terms of debugging facitilies.
  1. Login to the rkscli
  2. Execute hidden command "Ruckus"
  3. Copy and paste ";/bin/sh;" including quotes. This is required only
     once, the payload will be stored in writable filesystem.
  4. Execute hidden command "!v54!". Press Enter leaving empty reply for
     "What's your chow?" prompt.
  5. Busybox shell shall open.
  Source: https://alephsecurity.com/vulns/aleph-2019014
- Stock firmware has beamforming functionality, known as BeamFlex,
  using active multi-segment antennas on both bands - controlled by
  RF analog switches, driven by a pair of 74LV164 shift registers.
  Shift registers used for each radio are connected to GPIO14 (clock)
  and GPIO15 of the respective chip.
  They are mapped as generic GPIOs in OpenWrt - in stock firmware,
  they were most likely handled directly by radio firmware,
  given the real-time nature of their control.
  Lack of this support in OpenWrt causes the antennas to behave as
  ordinary omnidirectional antennas, and does not affect throughput in
  normal conditions, but GPIOs are available to tinker with nonetheless.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-09-11 01:36:25 +02:00
Rosen Penev
f4eef5f2a1 ramips: add support for Linksys E7350
Linksys E7350 is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specifications:
- SoC: MT7621 (880MHz, 2 Cores)
- RAM: 256 MB
- Flash: 128 MB NAND
- Wi-Fi:
  - MT7915D: 2.4/5 GHz (DBDC)
- Ethernet: 5x 1GiE MT7530
- USB: 1x USB 3.0
- UART: J4 (57600 baud)
  - Pinout: [3V3] (TXD) (RXD) (blank) (GND)

Notes:
* This device has a dual-boot partition scheme, but this firmware works
  only on boot partition 1.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-09-11 01:30:11 +02:00
Rosen Penev
26a6a6a60b ramips: add support for Belkin RT1800
Belkin RT1800 is an 802.11ax (Wi-Fi 6) router, based on MediaTek
MT7621A.

Specifications:
- SoC: MT7621 (880MHz, 2 Cores)
- RAM: 256 MB
- Flash: 128 MB NAND
- Wi-Fi:
  - MT7915D: 2.4/5 GHz (DBDC)
- Ethernet: 5x 1GiE MT7530
- USB: 1x USB 3.0
- UART: J4 (57600 baud)
  - Pinout: [3V3] (TXD) (RXD) (blank) (GND)

Notes:
* This device has a dual-boot partition scheme, but this firmware works
  only on boot partition 1.

Installation:

Upload the generated factory.bin image via the stock web firmware
updater.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-09-11 01:30:11 +02:00
Andrey Butirsky
5806914794 ramips: add support for Kroks Rt-Cse SIM Injector DS
Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958:
https://kroks.ru/search/?text=1958
See Kroks OpenWrt fork for support of other models:
https://github.com/kroks-free/openwrt

Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 5x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- USB: 1x
- SIM-reader: 2x (driven by a dedicated chip with it's own firmware)
- Buttons: reset
- LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.)

Flashing:
- sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254
- U-Boot launches a WEB server if Reset button is held during power up,
  IP: 192.168.1.1

MAC addresses as verified by OEM firmware:
vendor   OpenWrt   source
LAN      eth0      factory 0x4 (label)
2g       wlan0     label

Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-09-11 01:30:11 +02:00
Andrey Butirsky
0a79c77a4e ramips: add support for Kroks Rt-Pot mXw DS RSIM router
Aka "Kroks KNdRt31R19".
Ported from v19.07.8 of OpenWrt fork:
see https://github.com/kroks-free/openwrt
for support of other models.

Device specs:
- CPU: MediaTek MT7628AN
- Flash: 16MB SPI NOR
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- mPCIe: 1x (usually equipped with an LTE modem by vendor)
- Buttons: reset
- LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status

Flashing:
- sysupgrade image via stock firmware WEB interface.
- U-Boot launches a WEB server if Reset button is held during power up.
Server IP: 192.168.1.1

SIM card switching:
The device supports up to 4 SIM cards - 2 locally on board and 2 on
remote SIM-injector.
By default, 1-st local SIM is active.
To switch to e.g. 1-st remote SIM:
echo 0 > /sys/class/gpio/modem1power/value
echo 0 > /sys/class/gpio/modem1sim1/value
echo 1 > /sys/class/gpio/modem1rsim1/value
echo 1 > /sys/class/gpio/modem1power/value

MAC addresses as verified by OEM firmware:
vendor   OpenWrt   source
LAN      eth0      factory 0x4 (label)
2g       wlan0     label

Signed-off-by: Kroks <dev@kroks.ru>
[butirsky@gmail.com: port to master; drop dts-v1]
Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-09-11 01:30:11 +02:00
Andreas Böhler
5f8c86e654 realtek: add support for TP-Link SG2452P v4 aka T1600G-52PS v4
This is an RTL8393-based switch with 802.3af on all 48 ports.

Specifications:
---------------
 * SoC:       Realtek RTL8393M
 * Flash:     32 MiB SPI flash
 * RAM:       256 MiB
 * Ethernet:  48x 10/100/1000 Mbps with PoE+
 * Buttons:   1x "Reset" button, 1x "Speed" button
 * UART:      1x serial header, unpopulated
 * PoE:       12x TI TPS23861 I2C PoE controller, 384W PoE budget
 * SFP:       4 SFP ports

Works:
------
  - (48) RJ-45 ethernet ports
  - Switch functions
  - Buttons
  - All LEDs on front panel except port LEDs
  - Fan monitoring and basic control

Not yet enabled:
----------------
  - PoE - ICs are not in AUTO mode, so the kernel driver is not usable
  - Port LEDs
  - SFP cages

Install via web interface:
-------------------------

Not supported at this time.

Install via serial console/tftp:
--------------------------------

The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.

Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. To install OpenWRT:

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"

Power on device, and stop boot by pressing any key.
Once the shell is active:
 1. Ground out the CLK (pin 16) of the ROM (U6)
 2. Select option "3. Start"
 3. Bootloader notes that "The kernel has been damaged!"
 4. Release CLK as soon as bootloader thinks image is corrupted.
 5. Bootloader enters automatic recovery -- details printed on console
 6. Watch as the bootloader flashes and boots OpenWRT.

Blind install via tftp:
-----------------------

This method works when it's not feasible to install a serial header.

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"
 3. Watch network traffic (tcpdump or wireshark works)
 4. Power on the device.
 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6)
 6. When 192.168.0.30 makes tftp requests, release pin 16
 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-09-10 22:13:52 +02:00
Daniel Golle
f7dbdcfa54 mediatek: filogic: use WPS button instead of RST on BPi-R3
The GPIO used for the RST button is also used for PCIe-CLKREQ signal.
Hence it cannot be used as button signal if PCIe is also used.
Wire up WPS button to serve as KEY_RESTART in Linux and "reset" button
in U-Boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-10 19:20:26 +01:00
Tomasz Maciej Nowak
80baffd2aa ipq40xx: add support for Pakedge WR-1
Pakedge WR-1 is a dual-band wireless router.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 5x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
LEDS: 8x (3 GPIO controlled, 5 connected to switch)
Buttons: 1x GPIO controlled
UART: pin header J5
      1. 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Rename initramfs image to:
   openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb
   and copy it to USB flash drive with FAT32 file system.
2. Connect USB flash drive to the router and apply power while pressing
   reset button. Hold the button, on the lates bootloader version, when
   Power and WiFi-5 LEDs will start blinking release it. For the older
   bootloader holding it for 15 seconds should suffice.
3. Now the router boots the initramfs image, at some point (close to one
   minute) the Power LED will start blinking, when stops, router is fully
   booted.
4. Connect to one of LAN ports and use SSH to open the shell at
   192.168.1.1.
5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if,
   at some point, You want to go back to original firmware. The firmware
   provided by manufacturer on its site is encrypted and U-Boot accepts
   only decrypted factory images, so there's no way to restore original
   firmware.
6. If the backup is prepared, transfer the sysupgrade image to the router
   and use 'sysupgrade' command to flash it.
7. After successful flashing router will reboot. At some point the Power
   LED will start blinking, wait till it stops, then router is ready for
   configuration.

Additional information
U-Boot command line is password protected. Password is unknown.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2022-09-07 21:21:38 +02:00
Daniel Golle
292146fda6 arm-trusted-firmware-tools: update to v2.7
Update host build of fiptool and use the new python sptool.py instead
of the previous sptool executable.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-09-07 04:22:40 +01:00
Nick Hainke
f1b5ed3143 uboot-envtools: update to 2022.07
Update to latest version.

Remove upstreamed patches:
- 100-fw_env-make-flash_io-take-buffer-as-an-argument.patch
- 101-fw_env-simplify-logic-code-paths-in-the-fw_env_open.patch
- 102-fw_env-add-fallback-to-Linux-s-NVMEM-based-access.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-09-02 23:13:53 +02:00
Claudiu Beznea
e9f12931e6 at91bootstrap: use sdmmc0 as booting media for sama5d27_som1_ek
Commit 0b7c66c ("at91bootstrap: add sama5d27_som1_eksd1_uboot as
default defconfig") changed default booting media for sama5d27_som1_ek
board w/o any reason. Changed it back to sdmmc0 as it is for all the
other Microchip supported distributions for this board (Buildroot,
Yocto Project). The initial commit cannot be cleanly reverted.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-09-02 20:43:51 +02:00
Claudiu Beznea
9a49788008 uboot-at91: use sdmmc0 as booting media for sama5d27_som1_ek
Commit adc69fe (""uboot-at91: changed som1 ek default defconfigs")
changed the booting media to sdmmc1 as default booting w/o any reason.
The Microchip releases for the rest of supported distributions (Buildroot,
Yocto Project) uses sdmmc0 as default booting media for this board.
Thus change it back to sdmmc0. With this remove references to sdmmc1
config. The initial commit cannot be cleanly reverted.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-09-02 20:43:51 +02:00
Daniel Golle
11a6021866 arm-trusted-firmware-mediatek: update to sources of 2022-08-31
Drop downstream patches which have been replaced with equivalent
upstream changes.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-31 21:10:39 +01:00
Daniel Golle
0ea329fec4 uboot-mediatek: replace patches with updated versions
Weijie Gao has submitted an updated version of the patchset adding
support for MT7986 and MT7981 to U-Boot. Use that v2 patchset.

Changes of v2:
- Add cpu driver for print_cpuinfo()
- Fix NULL pointer dereference in mtk_image
  (was already fixed in OpenWrt)
- Fix coding style
- Minor changes

https://patchwork.ozlabs.org/project/uboot/list/?series=316148

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-31 14:02:45 +01:00
Daniel Golle
38f7e932a5 uboot-envtools: add support for Bananapi BPi-R3
Create new mediatek_filogic file and add entries for environment on
MMC, UBI and NOR for the Bananapi BPi-R3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-30 13:36:28 +01:00
Daniel Golle
c2bc1bd99a uboot-mediatek: add support for Bananapi BPi-R3
The Bananapi BPi-R3 board can boot from eMMC, SD card, SPI-NAND and
SPI-NOR, depending on the position of switches controlling the BOOTSEL
bootstrap pins as we as hard-wired chip-select lines. The position of the
chip-select switch SW6 decides whether either SD card or eMMC can be
accessed, SW5 selects either SPI-NAND or SPI-NOR.

Generate U-Boot for all 4 boot options. The SD card version allows
installation to SPI-NAND and SPI-NOR (eMMC cannot be accessed
simultanously with the SD card), the SPI-NAND version allows installation
to eMMC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-30 13:36:28 +01:00
Daniel Golle
0a18456ffc uboot-mediatek: no compression means IH_COMP_NONE
Treat missing compression node in FIT image as IH_COMP_NONE.
This is implicentely already happening in most places, but for now
was still triggering an annoying warning about initramfs compression
being obsolete despite compression note being absent.
Fix this.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-28 20:33:15 +01:00
Daniel Golle
20eee0d6cb uboot-mediatek: mt7986: add generic reset button support
Allow resetting environment to default values when defined button
exists in device tree.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-28 20:33:15 +01:00
Daniel Golle
85581cc89a uboot-mediatek: mt7986: support PSTORE/ramoops
Assign reserved memory for PSTORE/ramoops for the MT7986 SoC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-28 20:33:15 +01:00
Daniel Golle
d3a337a592 uboot-mediatek: additions from MTK SDK
* updated SNAND/SNFI driver brings support for MT7981
 * add support for MediaTek NAND Memory bad Block Management (NMBM)
   (not used for any boards atm, but could be useful in future)
 * wire up NMBM support for MT7622, MT7629, MT7981 and MT7986
 * replace some local patches with updated version from SDK
 * bring some legacy precompiler symbols which haven't been converted
   into Kconfig symbols in U-Boot 2022.07, remove when bumbping to
   U-Boot 2022.10:
   100-28-include-configs-mt7986-h-from-SDK.patch

Source: https://github.com/mtk-openwrt/u-boot
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-08-28 20:33:15 +01:00