In order to prepare OpenWrt support for other Acer W6 devices, this commit
moves all device tree components that are used by all Acer W6/W6e/W6d/W6m
routers from mt7986a-acer-predator-w6.dts to mt7986a-acer-w6-common.dtsi
(new file) and includes this dtsi file in mt7986a-acer-predator-w6.dts.
Minor changes had to be made to the device tree in order to improve clarity
and – notably – to reduce the number of dtc warnings:
- replace (obviously wrong) led@<N> gpio led entities by led-<N>
- remove unnecessary (default-state = "off") gpio led statements
- rename entity “memory” to “memory@0”
- add missing #address-cells and #address-size in /soc/mmc@11230000
- add missing #address-cells and #address-size in /soc/pcie@11280000
- introduce symbols “nvmem” and “swport0” in dtsi (referenced in dts)
The changes were checked with `diff -BEZbdtwy --suppress-common-lines ...`
(comparing two dts files created using old and new fdt-1 blobs again), see
https://github.com/openwrt/openwrt/pull/16861/#issuecomment-2455680020 .
This is the first of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ce3b36b3d5374709b9b091390cb9053657be17fa)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link CPE710-v2 is an outdoor wireless CPE for 5 GHz with one Ethernet
port based on the AP152 reference board. Compared to the CPE710-v1, the
only change observed in hardware is that the mdio address of the ethernet
physical changed from 0x4 to 0x0.
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate), based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO parabolic antenna
- Power, LAN, WLAN5G Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for around
30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5572e0196a93604716ec36ebb8db6737fc6677aa)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is done in preparation of adding support for the CPE710-v2,
which uses a similiar device tree.
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 832cc8ce04122ea726178687b5168187b2465f7f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.
Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"
Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.
Installation:
- Using the bootloader web server. Hold the reset button while turning
the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.
LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
(GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.
Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.
MAC addresses as verified by OEM firmware:
use address source
2g *:b0 factory 0x4 (label)
5g *:b1 factory 0x8004
LAN *:b2 factory 0x28
WAN *:b3 factory 0x2e
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Link: https://github.com/openwrt/openwrt/pull/16927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3a9752ea027b8969750c0dd7f89b6afc357dcffa)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5eb25dddb17fa3cf4958e91dfc9fc868c9eb03ac)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
New stm32 target introduces support for stm32mp1 based devices.
For now it includes an initial support of the STM32MP135F-DK device.
The specifications bellow only list supported features.
Specifications
--------------
SOC: STM32MP135FAF7
RAM: 512 MiB
Storage: SD Card
Ethernet: 2x 100 Mbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
Buttons: 1x Reset, 1x User (USER2)
USB: 4x 2.0 Type-A
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 851e7f77e424f24cda8531330f2d82ebc942c0a4)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These packages are needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e109831e07e398cc50839a30a1cf18c4436983f4)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The snd-usb-audio drivers uses media controller if media controller is set.
So add kmod-media-controller as dependency.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 109592524663ae8bbda47e4ad51a124153a1c903)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit bb3418f21f7b8fe0dcd335375d183dd2a81772bf)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b0adf5e0fdc0d4b449bced9191a95bf08124c1ac)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7bcc68ede36dcc66ec6cdb45c3201e0af0f90708)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6b9df468f05fefa21a8cbce2fdb2e59692b4d246)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e606366a2e018e0a3b25e3dd4b3a937bb53c70e1)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ff96bd84ce0bae633007cf0de82d69796cf3508a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This package contains nvram files for Murata's Wi-Fi/Bluetooth modules.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit be937952fdf8f78fb45ea001258074ddb45e0891)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All stm32 devices use BCM43430 Wi-Fi interface in SDIO mode.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 456e0aad97413816aee41e68b3d3cfdfadc2fd43)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add ATF for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 08dcb73c8d05aa774957422731bfed1b322648d7)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add U-Boot for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ac79ad0757764028a138d0138c8d9aa74420f9ed)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add OP-TEE for stm32 boards, with the first being STM32MP135F-DK.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit fae25d4001bcbae0bb1ce60b676bd421e97d78fc)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add a generic template include/optee-os.mk to build OP-TEE.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dedb90e8f82a179ad67b6eac3b6f8862b9183077)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)
These partitions weren't used:
firmware_backup
zrsave
config2
Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d8a9669093359d60f4d6f183b58a22f24cf01731)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit e52c57bb1b30375e0bcc5523db76a672a4a8b4a4 renamed all
network ports to match the faceplate of the Gowin 1U Rack
Mount Server and added the br-lan bridge for the eth* ports.
This commit adds the PoE port to the br-lan bridge and a
br-wan bridge for the two SFP ports so that all ports are
part of the default network configuration.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 75af6a0d736a696ca726cb44d813791858c29f0c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 3467ea905b40f0df87700a15b716b1f5a4efc955.
I merged it by accident.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 52b6c9247997e51a97f13bb9e94749bc34e2d52e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Popular bpi-r3 pwm fans like this one
https://www.amazon.com/youyeetoo-Barebone-Fan-BPI-R3-Integrated/dp/B0CCCTY8PS
will not work properly with current openwrt-23.05/24.10 firmware.
Trying different pwm setting
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
At the moment we have following cooling levels:
cooling-levels = <255 96 0>;
for cpu-active-high, cpu-active-medium and cpu-active-low modes correspondingly.
Thus only cpu-active-high and cpu-active-low are usable. I think this is wrong.
This patch fixes cpu-active-medium settings for bpi-r3 board.
PS: I know, the patch is not ideal as it can break pwm fan for some users.
There are some peoples that use handmade cooling solutions, but:
* discussed cooler is the only 'official' pwm cooler for bpi-r3
available on the market.
* most peoples will use passive cooling available on the market or
the discussed cooler.
* the pwm-fan dts section was added before the official cooler
appears on the market.
Thus it should not be a lot of harm from this fix.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16974
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3467ea905b40f0df87700a15b716b1f5a4efc955)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 22664498ebdd47aad9b15f62edbcaadd851fd62c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bec8edb6d61eb74e8d7578749560cbb5040f307a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e9dd6da91661612d2330c2b633f3dd55b93218f8)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Now that omnia-eeprom is marked nonshared building the cortex-a9 mvebu
subtarget will fail with:
ERROR: unable to select packages:
omnia-eeprom (no such package):
required by: world[omnia-eeprom]
This is because omnia-eeprom depends on TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia
which will not be satisfied in buildbots since CONFIG_TARGET_ALL_PROFILES
and CONFIG_TARGET_PER_DEVICE_ROOTFS are set in which case
CONFIG_TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia is not set.
So, lets simply depend on the mvebu/cortex-a9 subtarget.
Fixes: 371e7bef4046 ("omnia-eeprom: Mark it nonshared")
Link: https://github.com/openwrt/openwrt/pull/17007
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 90de3b277b8e1d121b2f7023578979c6b616167f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CONFIG_FB_INTEL is now visible on x86 since i915 driver is packaged as kmod
now and it stops compilation, so add it to the generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 57daea682e1c6e6da91f92efed717159f9ffffb0)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The config_get_bool also works with on/off, yes/no, true/false.
Add 'main' section name. This will make it easier to change settings from uci.
Add a link to documentation.
Signed-off-by: Sergey Ponomarev <stokito@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15579
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 4511fa4b30f73185597990ce563bbf3f96385292)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These get dynamically set based on compiler version. Not relevant for
targets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cd92cbddf8c473507a9af290c99f2aef8c368784)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Move settings CONFIG_INTEL_MEI_GSC_PROXY, CONFIG_INTEL_MEI_HDCP
and CONFIG_INTEL_MEI_PXP to target generic.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16971
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 84665993d6beed8ac2b557f8d3e005a29e3fd09c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This tool was build in the phase 2 build, there the
TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia dependecy was probably
not meat. Mark it as non shared to build it together with the target
where this option is set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/16975
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 371e7bef4046fb3992ecfb92b5b741c22fa3ade6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Disable drm-i915 module for target x86/geode.
Fixes: 77cfe8f ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16977
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 226f74badd61fb1586dd3531835aeaa3bf6fe467)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 491121288eaa9d20f3db8215a4790e8f0ee1f8ca)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fe481c9c47d97ebde1bc3c959924f4f9227c6c16)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5583d2318966d5d5dcdbdec2e34b8815d3f6419a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
On aarch64 musl gcc 14.x compiler, trying compiling elfutils 0.192 with
lto option enabled will cause null-dereference error.
Example error message:
...
elf_compress.c: In function 'elf_compress':
elf_compress.c:675:26: error: potential null pointer dereference [-Werror=null-dereference]
675 | shdr->sh_flags |= SHF_COMPRESSED;
| ^
elf_compress_gnu.c: In function 'elf_compress_gnu':
elf_compress_gnu.c:127:25: error: potential null pointer dereference [-Werror=null-dereference]
127 | shdr->sh_size = new_size;
| ^ ^
...
This is a false postive warning but will abort compilation if gcc has
`-Werror` flag. This commit add a patch for this, see the bugzilla
report below.
This commit backports a series of patches to fix some errors.
Add patch:
- 007-add-libeu-symbols-to-libelf.patch
- 008-fix-autoconf-ENABLE_IMA_VERIFICATION.patch
- 009-fix-null-dereference-with-lto.patch
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=32311
Signed-off-by: Ryan Keane <the.ra2.ifv@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16886
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit afffcd09e5f15be53f327a80ee87d391312eb805)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since the start of the Realtek target OpenWrt works with RTL83XX as the
target architecture. Upstream is using MACH_REALTEK_RTL instead. To
simplify further development align that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 65964c42f8744ed8ca09448a155b99e3a99be283)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
