a4355a6 firewall3: clean up the flow table detection logic
edd0dc5 firewall3: create a common helper to find strings in files
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The terminfo is required by the popular terminal multiplexer screen and
tmux, offer it by default as the size impact is minimal with 885 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The terminfo files were all in one row which is terrible to read.
Split them over multiple lines to improve readability.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The Pine64(+) and the SoPine64 baseboard has two USB ports. One of
these (the lower) is connected directly to a USB host, the other
one's (upper) PHY is shared with the separate OTG controller. In
order to get it working, MUSB support needs to be enabled.
As there are other targets which compile MUSB support into the kernel
and not package it into modules, the same is done here.
[ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364250] usb usb5: Product: MUSB HDRC host driver
[ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd
[ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto
[ 1.379891] hub 5-0:1.0: USB hub found
[ 1.383677] hub 5-0:1.0: 1 port detected
[...]
[ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 697.477180] usb 1-1: Product: USB Flash Disk
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This includes several improvements and fixes:
61db17e rules: fix device and chain usage for DSCP/MARK targets
7b844f4 zone: avoid duplicates in devices list
c2c72c6 firewall3: remove last remaining sprintf()
12f6f14 iptables: fix serializing multiple weekdays
00f27ab firewall3: fix duplicate defaults section detection
e8f2d8f ipsets: allow blank/commented lines with loadfile
8c2f9fa fw3: zones: limit zone names to 11 bytes
78d52a2 options: fix parsing of boolean attributes
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.
But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
There are only two lan ports and one wan port on Youku yk1
Fixes: e9baf8265b ("ramips: add support for Youku YK1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label
on the case, not LAN.
This patch fixes this issue.
Fixes: 50fdc0374b ("ath79: provide label MAC address")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.
The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The CONFIG_USERIO option is unset in multiple target configurations. On
the sunxi target it is activated. Move the kernel configuration option
to the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.
Fixes: 87046e87e2 ("kernel: add missing kernel config symbol")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bump to 5.10.26 reversed dependencies on IOMMU for CONFIG_VFIO thus
malta (at least) prompted for this new symbol.
Set it to 'false' in the default config. rockchip & X86 enable it in
target specific configs.
Thanks to Tony Ambardar for falling over this one
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This adds detection of the Sophos SG-105 and Sophos XG-105 models
and assignment of ethernet ports these models have to LAN/WAN.
Signed-off-by: Stan Grishin <stangri@melmac.net>
This version fixes 2 security vulnerabilities, among other changes:
- CVE-2021-3450: problem with verifying a certificate chain when using
the X509_V_FLAG_X509_STRICT flag.
- CVE-2021-3449: OpenSSL TLS server may crash if sent a maliciously
crafted renegotiation ClientHello message from a client.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
In commit 8c8496435a ("build: add GNU install to prerequisites") new
dependency was added, but addition to README was omitted.
Fixes: 8c8496435a ("build: add GNU install to prerequisites")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Building with MIPS16 was disabled in 2013 due to an issue with GCC TLS:
https://dev.archive.openwrt.org/ticket/13572. But after the problematic
GCC version was retired, this change wasn't revisited.
Re-enable MIPS16 builds to reduce average elfutils library sizes ~10%.
This was compile-tested on malta/mips32be and malta/mips32le, and linked
with iproute2 for run-testing. Package sizes follow:
Library MIPS16:=0 MIPS16:=1
------- --------- ---------
libelf1 43217 37492
libasm1 12481 11658
libdw1 229723 205793
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This became a bit of a tragedy, caused by a corner cases which wasn't
put into account during testing. DEFAULT_PACKAGES are defined in
target/linux/<target>/Makefile but also in
target/linux/<target>/<subtarget>/target.mk.
The latter was no longer imported when using DUMP=1, however not using
DUMP=1 while running the Makefile in target/linux/<target>/ caused duplicate
packages in the list.
As a solution, which should have been used from day 0, `make` runs in
target/linux/ without DUMP=1, resulting in no duplicate packages and all
inclusions from include/target.mk, linux/target/<target>/{Makefile,
<subtarget>/target.mk}
While at it, sort the list of default packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The commit "1bf2b3fe90 build,json: fixup missing arch_packages" fixes
the missing package architecture locally but runs $(TOPDIR)/Makefile
rather than a target specific one. While this works on local builds just
fine, it causes the buildbots to add garbage to the `arch_packages`
variable:
cd \"/builder/shared-workdir/build\"; git log --format=%h -1
toolchain > /builder/shared-workdir/build/tmp/.ver_check\ncmp -s
/builder/shared-workdir/build/tmp/.ver_check
/builder/shared-workdir/build/staging_dir/toolchain-x86_64_gcc-8.4.0_musl/stamp/.ver_check
|| { \\\n\trm -rf
/builder/shared-workdir/build/build_dir/target-x86_64_musl
/builder/shared-workdir/build/staging_dir/target-x86_64_musl
/builder/shared-workdir/build/staging_dir/toolchain-x86_64_gcc-8.4.0_musl
/builder/shared-workdir/build/build_dir/toolchain-x86_64_gcc-8.4.0_musl;
\\\n\tmkdir -p
/builder/shared-workdir/build/staging_dir/toolchain-x86_64_gcc-8.4.0_musl/stamp;
\\\n\tmv /builder/shared-workdir/build/tmp/.ver_check
/builder/shared-workdir/build/staging_dir/toolchain-x86_64_gcc-8.4.0_musl/stamp/.ver_check;
\\\n}\nx86_64
Only the last line contains the desired string.
Future investigation should check why the build system prints this to
stdout rather than stderr.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The recent removal of usbutils from core and replacement by hwdata in
packages has exposed hwdata's requirement for certain GNU options on
'install' (-T) Other packages (sqm-scripts) have openwrt specific
makefile sections to avoid GNU options but I suspect this is going to
get harder in the future.
Add GNU install as a prerequisite and link into
$STAGING_DIR/host/etc/bin as per similar GNU utils
This resolves an issue building under MacOS which would otherwise use a
non-GNU options aware version of 'install'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fixes issue openwrt/packages#14921, whereby inline ASM wasn't getting
built as PIC; look at gmp-6.2.1/mpn/x86/pentium/popcount.asm for
example:
ifdef(`PIC',`
...
for a routine that exists in both PIC and non-PIC versions.
Make sure that wherever $(FPIC) gets passed as a variable expansion
that it gets quoted where necessary (such as setting environment
variables in shell commands).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Fix 7f4c2b1 "build,json: fix duplicates in default_packages" which
removed duplicate default packages but also removed the package
architecture from the profiles.json.
If DUMP=1 is set, the `ARCH_PACKAGES` is no longer exported and
therefore empty. Fix this by running make twice, once with DUMP=1 and
once without.
Signed-off-by: Paul Spooren <mail@aparcar.org>
In case CONFIG_TARGET_MULTI_PROFILE is set, IMG_PREFIX cannot be
expanded. Use DEVICE_IMG_PREFIX instead and make sure it's defined.
Fixes: 8f89b1ab0f ("image: add 'append-image' build command")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It's helpful for accessing booting data (DTS, kernel, etc.). It has to
be used carefully as CFE's JFFS2 support is quite dumb. It doesn't
recognize deleted files and has problems handling 0 inode.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Populate the recovery and production partitions of the generated sdcard
image for the Bananapi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit 7ce1d9ce09 ("build: artifacts add dependency for built images")
now makes sure that sysupgrade and initramfs images are available at
the stage that artifacts are created.
Allow making use of that with a new build command 'append-image' to
be used in artifacts.
See the next commit for an example.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add possibility to use images and initramfs in artifacts.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
After backporting upstream ehci overcurrent patches we need to use spurious-oc
instead of ignore-oc.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch really annoys me, either it needs to go upstream or be
dropped, so it's going to be dropped here.
Checking drivers/platform/x86/pcengines-apuv2.c it also appears to be
incomplete since it mentions different dmi board names depending on bios
version.
/* APU2 w/ legacy BIOS < 4.0.8 */ is 'APU2'
/* APU2 w/ legacy BIOS >= 4.0.8 */ is 'apu2'
/* APU2 w/ mainline BIOS */ is 'PC Engines apu2'
So the patch, if applicable at all, only 'works' for legacy BIOS >=
4.0.8
My APU2 on mainline BIOS reboots fine without this patch. So let's see
if anyone screams and when they do question why legacy bios. If patch
DOES need to be re-introduced then it needs to go upstream first.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Straightforward refresh of patches using update_kernel.
Removed (reverse-applicable):
bmips/patches-5.10/010-v5.11-net-dsa-implement-a-central-TX-reallocation-procedur.patch
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Straightforward refresh of patches using update_kernel.
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
