Commit Graph

44300 Commits

Author SHA1 Message Date
Adrian Schmutzler
9aa8f87d27 ar71xx: Add "info" partition for TP-Link Archer C7 v5
This adds the "info" MTD partition, as it is specified in the
ath79 DTS:
https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35

This is required to set the WAN MAC address, as it is build based
on the LAN MAC address, which in turn has to be read from the
"info" partition:
https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Petr Štetiar
02556d6365 ath79: Add WPS button to TP-Link Archer C7v5
This patch adds currently missing support for the WPS button on TP-Link
Archer C7v5.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Adrian Schmutzler
0a13f589c3 ath79: Correct MAC address for WAN interface of Archer A7/C7 v5
These devices share the network config with C7v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.

Based on: https://github.com/openwrt/openwrt/pull/1726

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Adrian Schmutzler
a5885ea407 ath79: Fix GPIO reset button on TP-Link Archer C7v5
The GPIO for the reset button for the Archer C7v5 changed from
ar71xx to ath79. An investigation based on tests revealed
that the A7v5 responds on "11", while the C7v5 responds on
"5" as set for ar71xx.

Thus, we just define this in the DTS files instead of in the
common DTSI.

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Adrian Schmutzler
6f354c4d32 ath79: Utilize new LED modes from diag.sh for Archer A7/C7 v5
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Adrian Schmutzler
9888f1b96c ath79: Consolidate LEDs in Archer A7/C7 v5 DTSI
Definition is split here without obvious reason. Just merge it
(and align order to that from C7 v4).

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Christian Mauderer
8a4dc6f48c ath79: add support for Ubiquiti airCube ISP
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal
2x2 MIMO antennas. It can be supplied via a USB connector or via PoE.
There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an
optional PoE passthrough from the first LAN port to the WAN port.

SoC:       Qualcomm / Atheros QCA9533-BL3A
RAM:       64 MB DDR2
Flash:     16 MB SPI NOR
Ethernet:  4x 10/100 Mbps (1 WAN + 3 LAN)
LEDS:      1x via a SPI controller (not yet supported)
Buttons:   1x Reset
Serial:    1x (only RX and TX); 115200 baud, 8N1

Missing points:
- LED not yet supported
- Factory upgrade via web IF or TFTP recovery not yet supported
  (Needs RSA signed images, for details see PR#1958)

The serial port is on a four pin connextor labeled J1 and located
between Ethernet and USB connector. The pinout is:
1. 3V3 (out)
2. Rx (in)
3. Tx (out)
4. GND

Upgrading via serial port / U-Boot:
- Connect the serial port via a level converter
- Power the system and stop U-Boot with pressing any key when `Hit any
  key to stop autoboot` is displayed. Note: Pressing space multiple
  times untill U-Boot reaches that location works well.
- Connect a PC with the IP 192.168.1.100 (or some other in that net)
  running a TFTP-Server to one of the LAN ports. Copy the sysupgrade
  image to the server.
- Set the U-Boot server IP with
    setenv serverip 192.168.1.100
- Load the flash image to RAM with
    tftpboot 0x81000000 sysupgrade.bin
- Erase the flash with
    erase 0x9f050000 0x9ffaffff
- Write the new flash content with
    cp 0x81000000 0x9f050000 ${filesize}
- Reset the device with
    reset

Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
[removed full stop in subject and added lockdown note to commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Markus Scheck
de2f888024 ath79: add support for OCEDO Ursus
SOC:   Qualcomm Atheros QCA9558
RAM:   128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED:   Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
       Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
       The Serial setting is 115200-8-N-1

INSTALLATION:

1. Serve an OpenWrt ramdisk image named "ursus.bin".
   Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
   the boot process.
3. Set the correct bootcmd with
   > setenv bootcmd run bootcmd_1
   > saveenv
4. Run
   > tftpboot 0x81000000 ursus.bin
   > bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.

Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
189aa1748b ath79: ag71xx: Enable tx hang workaround for the rest of ar724x SoCs
In ar71xx we check for stuck DMA on devices which fall in the is_ar724x
SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x).

In ath79 we're currently performing this check only for devices with
ar7240 SoC, so this patch tries to sync the dma stuck checking behavior
with what is being done in ar71xx.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
31ea08a64b ar71xx: ag71xx: Fix broken networking on some devices (FS#2177)
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.

Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
0f8cdc28af ar71xx: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
6009b3fd58 ar71xx: ubnt-m-xw: Fix factory image flashing using TFTP recovery
This is backport of the same functionality in ath79, from commit
 d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP
             recovery method")

Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:

 All future airOS versions will be signed in this way and not allow
 unsigned firmware to be loaded except via TFTP.

U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:

 Hit any key to stop autoboot:  0
 Setting default IP 192.168.1.20
 Starting TFTP server...
 Receiving file from 192.168.1.25:38438
 Received 4981148 bytes
 Firmware check failed! (1)

By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:

 Received 3801500 bytes
 Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44
 Setting U-Boot environment variables
 Un-Protected 1 sectors
 Erasing Flash.... done

Patch provided by AREDN[3] project, tested on Bullet M2 XW.

1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
d23222a96c imx6: Add support for Toradex Apalis family of CoMs
This patch adds support for the following computer on modules (CoM) from
Toradex[A]:

 Apalis iMX6 Quad 2GB IT - i.MX 6Quad 800MHz, 2GB DDR3, 4GB eMMC
                                             -40° to +85° C Temp
 Apalis iMX6 Quad 1GB    - i.MX 6Quad 1GHz,   1GB DDR3, 4GB eMMC
                                               0° to +70° C Temp
 Apalis iMX6 Dual 1GB IT - i.MX 6Dual 800MHz, 1GB DDR3, 4GB eMMC
                                             -40° to +85° C Temp
 Apalis iMX6 Dual 512MB  - i.MX 6Dual 1GHz, 512MB DDR3, 4GB eMMC
                                               0° to +70° C Temp

I've developed and tested it on Quad 2GB IT v1.1A and Dual 512MB v1.1A
CoMs, using Ixora[B] carrier board v1.0A, but it should hopefuly work on
Eval[C] board as well.

A. https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-freescale-imx-6
B. https://www.toradex.com/products/carrier-board/ixora-carrier-board
C. https://www.toradex.com/products/carrier-board/apalis-evaluation-board

Flashing/recovery instructions:

 1. Download and compile imx_loader for OpenWrt from
    https://github.com/ynezz/imx_loader

 2. Enter recovery mode as desribed in
    https://developer.toradex.com/knowledge-base/imx-recovery-mode

 3. Connect board via USB to the host computer, check that it's connected
    by lsusb:

    15a2:0054 Freescale Semiconductor, Inc. i.MX 6Dual/6Quad SystemOnChip
              in RecoveryMode

 4. Copy following OpenWrt images to imx_loader directory:
         SPL
         u-boot.img
         u-boot-with-spl.imx
         openwrt-imx6-apalis-recovery.scr
         openwrt-imx6-apalis-squashfs.combined.bin

 5. Run imx_usb in imx_loader directory

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
dc1a73984e imx6: image: Split imx6-sdcard image for reusability
I'm going to reuse the imx6-sdcard image commands for building of Apalis
eMMC images.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:03 +02:00
Petr Štetiar
adb0a420e5 uboot-envtools: imx6: Add support for Toradex Apalis board family
This patch is needed in order to be able to use fw_{set,print}env
commands.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:03 +02:00
Petr Štetiar
136001675e uboot-imx6: Add support for Toradex Apalis board family
This patch is needed in order to properly boot OpenWrt bootscript.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:03 +02:00
Hans Dedecker
8f1cbef12e glibc: update to latest 2.27 commit [BZ #22964]
de9d4aa353 ja_JP locale: Add entry for the new Japanese era [BZ #22964]

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-04-08 16:07:11 +02:00
Koen Vandeputte
8df12d76c6 kernel: bump 4.19 to 4.19.34
Refreshed all patches.

Removed:
- 030-PCI-dwc-skip-MSI-init-if-MSIs-have-been-explicitly-d.patch

Altered:
- 366-netfilter-nf_flow_table-clean-up-and-fix-dst-handlin.patch
- 650-netfilter-add-xt_OFFLOAD-target.patch
- 662-remove_pfifo_fast.patch
- 332-arc-add-OWRTDTB-section.patch
- 100-clocksource-drivers-arch_timer-Workaround-for-Allwin.patch
- 702-phy_add_aneg_done_function.patch

New symbols:
- ARC_IRQ_NO_AUTOSAVE
- SUN50I_ERRATUM_UNKNOWN1

Compile-tested: cns3xxx, imx6, sunxi
Runtime-tested: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 14:53:39 +02:00
Koen Vandeputte
5387bc9cbb kernel: bump 4.14 to 4.14.111
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 14:53:39 +02:00
Koen Vandeputte
1138e0f887 kernel: bump 4.9 to 4.9.168
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 14:53:39 +02:00
Koen Vandeputte
5eac37624f kernel: bump 4.14 to 4.14.110
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 12:07:28 +02:00
Koen Vandeputte
6fe9127a56 kernel: bump 4.9 to 4.9.167
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 12:07:28 +02:00
Hans Dedecker
80568e5854 dropbear: bump to 2019.78
Fix dbclient regression in 2019.77. After exiting the terminal would be left
in a bad state. Reported by Ryan Woodsmall

drop patch applied upstream:
	010-tty-modes-werent-reset-for-client.patch

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-04-07 20:32:55 +02:00
Stijn Tintel
310e2764a8 ubox: bump to git HEAD
5130fa4 kmodloader: fix and optimize loading of failed modules

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-04-07 19:37:18 +03:00
Tomasz Maciej Nowak
f0be038897 tools: cbootimage: depend on automake
Fix missing aclocal reported by buildbot.

Fixes: 8595bb0 ("tools: add cbootimage for tegra")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-07 15:25:28 +02:00
Christian Lamparter
7f3facfce2 firmware-utils: fix nec-enc build on older architectures
This patch enable gnu99 mode for the nec-enc utility which
fixes the following build-breaking errors on some older
architectures.

nec-enc.c: In function ‘xor_data’:
nec-enc.c:34:2: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
  for (int i = 0; i < len; i++) {
  ^~~
nec-enc.c:34:2: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
nec-enc.c: In function ‘main’:
nec-enc.c:101:3: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
   for (int i = 0; i < n; i++) {
   ^~~

Spotted-By: Buildbot
Fixes: fac27643f0 ("firmware-utils: add nec-enc")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-04-06 20:29:35 +02:00
Kip Porterfield
b812a7fa68 ramips: correct DTS for Belkin F9K1109v1 to include switch definition
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.

Fixes: 017ec068e3 (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2019-04-06 19:14:06 +02:00
INAGAKI Hiroshi
643fcfc8d6 ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
2019-04-06 19:14:06 +02:00
INAGAKI Hiroshi
fac27643f0 firmware-utils: add nec-enc
nec-enc provides firmware encoding/decoding with model specific key
for NEC devices.

known devices:

  - Aterm WF1200CR
  - Aterm WG1200CR
  - Aterm WG2600HS

usage:

  nec-enc -i infile -o outfile -k key

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch fixes, marked usage as noreturn, added static function,
moved buf* from stack to the global data segment]
2019-04-06 19:14:06 +02:00
Chuanhong Guo
d80a1c6e2c ramips: backport mt7621-spi from linux-next-20190329
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.

Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-04-06 19:14:06 +02:00
Eneas U de Queiroz
8252511dc0 build: remove sgid permission from tar
Otherwise tar will keep the sgid bit when running
from a sgid-set directory, resulting in a different
file being generated.

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message, removed DMARC]
2019-04-06 19:14:06 +02:00
Michael Heimpold
32a6c252db wpan-tools: clean up Makefile
When we only call the default, we do not need to define it explicitly.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-04-06 19:14:06 +02:00
Michael Heimpold
007e947976 fconfig: cleanup Makefile
We do not need to define an empty Build/Configure since
the default checks for existing ./configure and does nothing
in case nothing is found.

Similar for Build/Compile: we can remove the definition
when we only call the default.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2019-04-06 19:14:06 +02:00
Rosen Penev
46dc4e206d tools/xz: Compile with PIC to fix linking errors
I made a similar change to this here:
https://github.com/openwrt/packages/pull/8159

However, it turns out this did not fix the problem as the problem has to
do with tools/xz and not the xz package. The error is the same and causes
linking errors as can be seen above.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2019-04-06 19:14:06 +02:00
Adrian Schmutzler
0eef05fb36 ath79: Utilize tplink-safeloader definition
Currently, tplink-safeloader definition is only used a base for
another common definition.

This patch adjusts tplink-safeloader so it can be actually used
for some targets in generic-tp-link.mk.

This patch is cosmetic except for the order of
"check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged
for the tplink_re350k-v1 .

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with
tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's
extra IMAGE/sysupgrade.bin rule]
2019-04-06 19:14:06 +02:00
Rosen Penev
2a8175a7ac kernel: Add RIPEMD160 module
After getting rid of cryptsetup's heavy openssl dependency, there is now
the problem of missing RIPEMD160 support. RIPEMD160 is used for True/Vera
crypt volumes as well as old LUKS1 ones.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2019-04-06 19:14:06 +02:00
David Bauer
b19c48dc34 ramips: enable R6120 USB power
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-06 19:14:06 +02:00
Michael Gray
5198258d10 tools: tplink-safeloader: add C7v5 KR Support
The added entry originates from TP-Links latest Archer C7 v5 KR firmware.

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2019-04-06 19:14:06 +02:00
Tomasz Maciej Nowak
bac2c4d2fb ath79: engenius epg5000: add leds migration script
With transition from ar71xx to ath79 some of devices change their naming
of LEDs. When upgrading from ar71xx target images this will require the
user to adjust previously working configuration. This commit adds
migration script which can be used to rename old names to new ones.
With this previously working configuration will be automatically
adjusted, wihtout user intervention.

This commit adds migration case for EnGenius EPG5000, the wireless LEDs
names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to
epg5000:blue:wlan2g and epg5000:blue:wlan5g.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 19:14:05 +02:00
Tomasz Maciej Nowak
afef17e24d base-files: add leds migration
Currently leds migration scripts in ar71xx and lantiq share a lot of
logic and introducing leds migration to another target would mean
copying this code, again. Therefore add common logic to library in
base-files package.

Suggested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 19:14:05 +02:00
Zhao Yu
32689e93c4 ramips: add support for Youku YK-L2
Hardware spec:

CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0

Flashing instructions:

Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692

to get the bootloader and unlock firmware.

0. upgrade your router with the telnet firmware via the
   firmware upgrade page on the webui.

1. telnet 192.168.11.1 from your PC

2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
   it to the /tmp directory of the router.

3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader

4. turn off the power

5. Push the reset button while turning on the router and
   wait until LED start blinking (~10sec.)

6. Connect Ethernet port and goto http://192.168.1.1.

7. Upload the firmware to firmware restore page in webui.

Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
2019-04-06 19:13:49 +02:00
Jason A. Donenfeld
549d44736a wireguard: bump to 0.0.20190406
* allowedips: initialize list head when removing intermediate nodes

Fix for an important regression in removing allowed IPs from the last
snapshot. We have new test cases to catch these in the future as well.

* tools: warn if an AllowedIP has a nonzero host part

If you try to run `wg set wg0 peer ... allowed-ips 192.168.1.82/24`, wg(8)
will now print a warning. Even though we mask this automatically down to
192.168.1.0/24, usually when people specify it like this, it's a mistake.

* wg-quick: add 'strip' subcommand

The new strip subcommand prints the config file to stdout after stripping
it of all wg-quick-specific options. This enables tricks such as:
`wg addconf $DEV <(wg-quick strip $DEV)`.

* tools: avoid unneccessary next_peer assignments in sort_peers()

Small C optimization the compiler was probably already doing.

* peerlookup: rename from hashtables
* allowedips: do not use __always_inline
* device: use skb accessor functions where possible

Suggested tweaks from Dave Miller.

* blake2s: simplify
* blake2s: remove outlen parameter from final

The blake2s implementation has been simplified, since we don't use any of the
fancy tree hashing parameters or the like. We also no longer separate the
output length at initialization time from the output length at finalization
time.

* global: the _bh variety of rcu helpers have been unified
* compat: nf_nat_core.h was removed upstream
* compat: backport skb_mark_not_on_list

The usual assortment of compat fixes for Linux 5.1.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2019-04-06 17:26:47 +02:00
Daniel Engberg
6c22545225 target/octeon: Add Linux 4.19 support
This commit adds support for Linux 4.19 kernel, various cleanups
listed below.

Drop 170-cisco-hack.patch as these devices never seems to have been
supported.

Unset kernel symbols:

* CONFIG_CAVIUM_CN63XXP1=y
  No supported hardware uses CN63XXP1 and it causes "slight decrease in
  performance"
  Source: https://cateee.net/lkddb/web-lkddb/CAVIUM_CN63XXP1.html

* CONFIG_USB_OCTEON_EHCI=y
  CONFIG_USB_OCTEON_OHCI=y
  Deprecated
  Source: https://cateee.net/lkddb/web-lkddb/USB_OCTEON_EHCI.html
  https://cateee.net/lkddb/web-lkddb/USB_OCTEON_OHCI.html

Removed kernel symbols:

* # CONFIG_ARCH_HIBERNATION_POSSIBLE=y
* CONFIG_ARCH_SUSPEND_POSSIBLE=y
  These are not in if you do a vanilla config of a MIPS Octeon kernel
  and I can't find any references about support on this platform.

* # CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
* CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
  No need to have this in by default, not defined in most other targets

* CONFIG_CRASH_CORE=y
  Can't find any documentation why this should be enabled by default

* CONFIG_DEBUG_INFO=y
  Set by https://github.com/openwrt/openwrt/blob/master/config/Config-kernel.in#L134

* CONFIG_DEBUG_SPINLOCK=y
  No need to have this in by default

* CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120
  Already set by default
  Source: https://cateee.net/lkddb/web-lkddb/DEFAULT_HUNG_TASK_TIMEOUT.html

* CONFIG_DETECT_HUNG_TASK=y
  No need to have this in by default, not defined in most other targets

* CONFIG_HAVE_DEBUG_KMEMLEAK=y
  No need to have this in by default, not defined in most other targets

* CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
  No need to have this in by default

* CONFIG_HAVE_IDE=y
  None of the supported devices have IDE

* CONFIG_HZ=250
* # CONFIG_HZ_100 is not set
* CONFIG_HZ_250=y
  This is broken with generic config

* CONFIG_KALLSYMS=y
  No need to have this in by default, not defined in most other targets

* CONFIG_KEXEC=y
* CONFIG_KEXEC_CORE=y
  No need to have this in by default, not defined in most other targets

* CONFIG_HAVE_KVM=y
  No need to have this in by default

* CONFIG_SCHED_DEBUG=y
  No need to have this in by default, not defined in most other targets

* CONFIG_SYSFS_DEPRECATED=y
  Deprecated symbol
  Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED.html

* CONFIG_SYSFS_DEPRECATED_V2=y
  Discouraged usage in general
  Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED_V2.html

* CONFIG_UNINLINE_SPIN_UNLOCK=y
  No need to have this in by default, not defined in most other targets
  Source: https://github.com/openSUSE/kernel/blob/master/lib/Kconfig.debug#L1137

* CONFIG_ZLIB_INFLATE=y
  No need to have this in by default, not defined in most other targets

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
2e5a0b81ec mvebu: sysupgrade: sdcard: keep user added partitons
Currently sysupgrade overwrites whole disk and destroys partitions added
by user. Sync the sysupgrade code with the one present in x86 target to
remedy this behaviour.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
4e8345ff68 mvebu: base-files: autodetect upgrade device
Since some boards could be also booted from other mediums than SD card,
lets make the upgrade block device autodetected.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
727c3df5bb mvebu: shrink amount of packages and reorganize them
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
55b4ff7f73 mvebu: use ext4 for clearfog image bootfs
This will allow to drop additional packages and shrink image size.

Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
910eb994eb mvebu: make bootfs size for sdcard image configurable
Let's take this oportunity to implement boot-part and rootfs-part feature
flags.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Luis Araneda
78a3c51985 zynq: replace storage related configs by packages
Select build-in packages by default and remove the
associated kernel configs

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2019-04-06 16:31:10 +02:00
Luis Araneda
3db12da7cd zynq: replace CAN kconfig options by device packages
The options are managed on a generic way by the can
kmod packages

Additionally, select can packages only for devices that
currently has CAN enabled, which is only the ZC702

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2019-04-06 16:31:10 +02:00