Kernel 6.1 have renamed complete_and_exit to kthread_complete_and_exit.
This was just a rename and nothing is changed implementation wise.
Fix compilation error by using the new symbol name.
Fix compilation error:
In file included from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/osdep_service.h:41,
from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:32,
from /builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:22:
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c: In function 'rtw_cmd_thread':
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/include/osdep_service_linux.h:166:23: error: implicit declaration of function 'complete_and_exit' [-Werror=implicit-function-declaration]
166 | #define thread_exit() complete_and_exit(NULL, 0)
| ^~~~~~~~~~~~~~~~~
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:706:9: note: in expansion of macro 'thread_exit'
706 | thread_exit();
| ^~~~~~~~~~~
/builder/shared-workdir/build/sdk/build_dir/target-aarch64_cortex-a53_musl/linux-bcm27xx_bcm2710/rtl8812au-ct-2021-11-07-39df5596/core/rtw_cmd.c:708:1: error: control reaches end of non-void function [-Werror=return-type]
708 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Kernel 6.1 renamed and moved complete_and_exit to
kthread_complete_and_exit.
This was just a rename and nothing is changed implementation wise.
Update to the new symbol name to fix compilation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch adds basic TX power control for the MT7620 and limits its
maximum TX power. This can avoid the link speed decrease caused by
chip overheating.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
U-Boot complains that the overlayed DT needs relocation, so set
DEVICE_DTS_LOADADDR to have it relocated.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport merged patch fixing broken hwspinlock due to missing regmap
config for SFPB MMIO implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This drops a use of downstream "mac-address-increment".
Cc: Christian Svensson <blue@cmd.nu>
Cc: Tommy Nevtelen <tommy@nevtelen.com>
Cc: Viktor Ekmark <viktor@ekmark.se>
Cc: Daniel Wennberg <github@networkninja.se>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Svensson <blue@cmd.nu>
With upstream accepted "mac-base" binding there is no need for a
downstream "mac-address-ascii" workaround anymore.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[TP-Link EC330-G5u v1 - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
ChangeLog:
125b080 Release version 6.4.
5660918 update UAPI header copies
f493e63 netlink: fix duplex setting
b3e341c cmis: report LOL / LOS / Tx Fault
045d8db sff-8636: report LOL / LOS / Tx Fault
a6505f3 drop checks for macros provided in UAPI header copies
86c0c41 do not check for strtol() function
dd8e3ae actually check for C11 compiler
43e4d30 add local copies of macros from autoconf-archive
faa4700 drop check for big endian types
31b7b5e Require a compiler with support for C11 features
946d18b update UAPI header copies
eebf01f ethtool: Add support for configuring tx-push-buf-len
2782ea8 update UAPI header copies
Signed-off-by: Nick Hainke <vincent@systemli.org>
return ubnt_rocket-m and ubnt_powerbridge-m back to ath79-generic
They have enough RAM-ressources to not be considered as tiny.
This reverts the commit f4415f7635 partially
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
The duplicate sections are caused by a race condition at boot, when board.json
is not available. In that case, the final phy name cannot be resolved, and extra
sections referring to the path are created.
Fix this by making sure that wifi config is not being run before board.json
is created.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Changelog from quic:
Bug fixes, stability improvements from previous releases
are present. There are no backward comatibility issues
with this release.
Tested-by: Michał Kwiatek <michal@kwiatek.it> # Xiaomi AX3600
Signed-off-by: Michał Kwiatek <michal@kwiatek.it>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
the SDK's Makefile referenced the old file name.
Update it too.
Fixes: 2d5f7035cf ("sdk: rename README")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware information:
---------------------
- RTL8380 SoC
- 8 Gigabit RJ45 PoE ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
- PoE chips: Nuvoton M0516LDE + BCM59121
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc002)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '180'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
removed redundant eeprom partition nodes from
cn7130_ubnt_edgerouter-4.dts and cn7130_ubnt_edgerouter-6p.dts
as they are identically defined in cn7130_ubnt_edgerouter-e300.dtsi.
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(integrated eeprom referenced node in the .dtsi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MAC addresses should be read from 3rd MTD partition,
but only two MTD partitions are populated.
To fix it, a partitions node has to surround the partition
nodes in device tree.
Tested with Edgerouter 6P
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(fixed checkpatch complains)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
LEDs on Edgerouter 6P didn't work correctly:
blue /white LED swapped, on/off state inverted
Fixed in device tree:
swap the GPIO ports for power:blue and power:white LEDs
change LED activity from LOW to HIGH
Tested on Edgerouter 6P
Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
This is the first commit to introduce the base for the N821 board used
in Cisco vEdge 1000.
This commit does not include the custom CPLD drivers but rather
everything else that is already present in the upstream kernel.
This results in an image that boots, but e.g. the SFP ports are not
usable.
Hardware:
- CPU: Cavium Networks CN6130, 4 cores @ 1.0 GHz
- Flash:
- 16 MiB SPI NOR presented as 2x8 MiB for A/B boot recovery
- 8192 MiB eMMC
- RAM: 4096 MiB
- Ethernet 1Gbit ports: 1x
- Ethernet SFP ports: 8x
- USB ports: 2x 3.0 Type-A on front panel
- Serial: Two, one internal and one external
- JTAG: Yes
- LED count: 18x
- Button count: 1x
- GPIOs: 1x
- Power: 2x redundant DC 12V barrel plug
- Extra: Slot for SD card on front
See the OpenWrt wiki for more hardware details.
Installation:
- Flash squashfs to /dev/sda2 and put kernel on /dev/sda1.
- Update uboot's bootcmd environment variable to match.
Full installation guide will be added to OpenWrt wiki when sysupgrade
support is added.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Tommy Nevtelen <tommy@nevtelen.com>
Tested-by: Viktor Ekmark <viktor@ekmark.se>
Tested-by: Daniel Wennberg <github@networkninja.se>
For the N821 platform we need to load the AT24 EEPROM driver before
everything else in order for the MAC address to be available at
driver initialization time.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Instead of loading the whole image into the memory when generating the
sha256 sum, we load the file in chunks and update the hash incrementally
to avoid MemoryError in python. Also remove a stray empty line.
Fixes: #13056
Signed-off-by: Adones Pitogo <pitogo.adones@gmail.com>
(mention empty line removal, adds Fixes from PR)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
'help' target fails not finding a file, so follow up on a change[2] made
as a fix for main README[1].
1. d0113711a3 ("README: port to 21st century")
2. 751486b31f ("build: fix README.md reference after rename")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Some device recipes remove default target packages. If user tries to add
them back they will be ignored, since packages list is processed in one
go. Process the device recipe packages first and do user ones later, so
additions won't get filtered out.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
There is no need to use reference if original node it specified in
exactly the same file. This is a minor cleanup simplifying DTS code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
DT binding for MAC cells in fixed layout was upstream approved and
accepted. Add support for it. This can replace quite some of our
downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The PHY of the wan2 port on MQmaker WiTi is wired to the second MAC of the
SoC. Rename the wan interface to wan1 and define it under the switch node,
effectively disabling the PHY muxing of the MT7530 switch's phy4.
Define the PHY of the wan2 port and adjust the gmac1 node accordingly. Now
that the PHY muxing feature is not being used anymore, the wan2 port can be
used to achieve 2 Gbps total bandwidth to the CPU.
Tested-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Rename GB-PC1 to GnuBee GB-PC1, and GB-PC2 to GnuBee GB-PC2. Let's not make
naming exceptions because of marketing whims.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Add the __extension__ mark before #include_next in strings.h
to avoid a compiler error when -pedantic is enabled.
This has been done for all other headers in the past.
Signed-off-by: Matthias Van Parys <matthias.vanparys@softathome.com>
DT overlays do not need relocation in order to be applied, so drop
defining the load address for dtbos.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
