Disable compiling qca8081 PHY driver in favor of upstream to better
support it and add better control of attached LEDs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Completely disable dump_survey code on ARCH_BCM2835 to fix defined but not
used warning.
512b762ddb (commitcomment-137899352)
Fixes: 512b762ddb ("mac80211: brcm: disable dump_survey on Raspberry Pi")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Enabling this causes slow iwinfo calls on Raspberry Pi and LuCI slows down
when wireless is enabled.
Fixes: https://github.com/openwrt/openwrt/issues/14013
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch has been reverted in the Raspberry Pi linux repository.
Also refresh the rest of the patches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[rmilecki: port to 5.15]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
raspberrypi/firmware is about 40G, so getting the full history log isn't an
option.
There have been multiple improvements and also support for the RPi 5 has been
added.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel module for lp5562 LED driver.
The kmod-leds-lp5562 depends on kmod-leds-lp55xx-common.
Signed-off-by: CheWei Chien <chewei.chien@wnc.com.tw>
This reverts commit b7f9742da8.
There are several reports of regressions with this commit. Will be added
back once I've figured out and fixed the cause
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When hitting a timing window where ubus configuration calls are hitting hostapd
and wpa_supplicant simultaneously, they can deadlock waiting for each other.
Fix this by using a lock around the ubus calls.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Frequent crashes have been observed on MT7916 based platforms. While the
root of these crashes are currently unknown, they happen when decoding
rate information of connected STAs in AP mode. The rate-information is
associated with a band which is not available on the PHY.
Check for this condition in order to avoid crashing the whole system.
This patch should be removed once the roout cause has been found and
fixed.
Link: https://github.com/freifunk-gluon/gluon/issues/2980
Signed-off-by: David Bauer <mail@david-bauer.net>
Add modules.builtin.modinfo to the kernel package, to support presence
testing using module aliases and printing module details with 'modinfo'.
With related kmodloader changes this adds ~2 KB to compressed image sizes.
root@OpenWrt:/# modinfo unix
name: unix
filename: (builtin)
alias: net-pf-1
license: GPL
root@OpenWrt:/# modprobe net-pf-1 && echo SUCCESS || echo FAIL
SUCCESS
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add modules.builtin to the kernel package for improved handling of loadable
and builtin modules. As with other distros, this allows 'modprobe <module>'
to consistently return success for both loaded/built-in modules, a useful
feature for presence-testing.
Given OpenWrt's few built-in modules, this change and related kmodloader
support add ~1 KB to the compressed image size.
Using sch_fq_codel (builtin) and sch_cake (loadable) for example:
root@OpenWrt:/# modprobe sch_fq_codel && echo SUCCESS || echo FAIL
SUCCESS
root@OpenWrt:/# modprobe sch_cake && echo SUCCESS || echo FAIL
SUCCESS
root@OpenWrt:/# rmmod sch_fq_codel
module is builtin
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Fixes: openwrt#12420
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Detach of-mdio dependency from stmmac-core kmod to fix support for
x86_64 target. This target doesn't use OpenFirmware infrastructure and
stmmac-core for the dwmac-intel driver doesn't depends on it.
Add kmod-of-mdio to any other user of stmmac-core as it's not inherit
from stmmac-core anymore.
Fixes: #14209
Fixes: 4b4c940fbc ("x86: Add kmod-dwmac-intel")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move pcs-xpcs kmod from armsr modules.mk to generic modules package.
Also add additional dependency to x86_64 as stmmac-core it's now used
by x86_64 target and depends on this package.
Fixes: 4b4c940fbc ("x86: Add kmod-dwmac-intel")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Might be a typo in drv->txtstamp function:
+ phy_rxtstamp(ndev->phydev, skb, 0);
to
+ phy_txtstamp(ndev->phydev, skb, 0);
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Remove upstreamed patches:
* replace usage of the deprecated "pci-dma-compat.h" API (6c03b27)
* remove uaccess and get_fs calls from PCIe for Kenel >= 5.18 (1d0d08c)
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ISISC is the QCA codename for their Atheros switch family including
AR237, QCA8337 etc.
Since we have qca8k support in OpenWrt, there is no need to have SSDK
support for these switches, and boards that also have external switches
can just use qca8k.
Disable QCA803x PHY support as well, since all of those are supportable
via at803x driver.
Signed-off-by: Robert Marko <robimarko@gmail.com>
PTP and swconfig support in SSDK require kernel modifications we dont need
nor we want to support for now, so move the PTP and swconfig disablement
into general build options as they are not ipq807x specific.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Recent SSDK versions started also parsing the "SoC" variable to identify
the SoC along with the "CHIP_TYPE".
We are not passing "SoC" currently and this leads to components we dont
need like MHT (New 2.5G quad port switch) being compiled and then unused,
so lets just pass the "SoC" as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTW88 PCI/USB driver uses the same firmware,
so add firmware dependencies.
Also CI report that:
Package kmod-rtw88-usb is missing dependencies for the following libraries:
usbcore.ko
This commit fixes it.
Fixes: 3538a19 ("mac80211: split rtw88 configuration for each supported chip")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Commit 947b44d ("ipq807x: fix wrong define for LAN and WAN ess mask")
started fixing wrong switch_lan_bmp that defined lan there weren't
actually present. This displayed a fragility in the malibu phy init code
in qca-ssdk.
Add patch to fix this. Also update each DTS with the new required
property if needed.
The new binding malibu_phy_start_addr is required with devices that
place the malibu first PHY referring port1 on a different PHY addres
than 0. The most common configuration is 0 but some device (for example
Qnap 301W) place the malibu PHY at an offset to address 16.
Refer to ipq8074-ess dtsi for extensive description on how to derive
this value.
Quoting the patch detailed description:
The usage of first_phy_addr is EXTREMELY FRAGILE and results
in dangerous results if the OEM (or anyone that by chance try to
implement things in a logical manner) deviates from the default values
from the "magical template".
To be in more details. With QSDK 12.4, some tweaks were done to improve
autoneg and now on every call of port status, the phydev is tried to
add. This resulted in the call and log spam of an error with ports that
are actually not present on the system with qsdk reporting phydev is
NULL. This itself is not an error and printing the error is correct.
What is actually an error from ages is setting generic bitmap reporting
presence of port that are actually not present. This is very common on
OEM where the switch_lan_bmp is always a variant of 0x1e (that on bitmap
results in PORT1 PORT2 PORT3 PORT4 present) or 0x3e (PORT1 PORT2 PORT3
PORT4 PORT5). Reality is that many device are used as AP with one LAN
port or one WAN port. (or even exotic configuration with PORT1 not
present and PORT2 PORT3 PORT4 present (Xiaomi 3600)
With this finding one can say... ok nice, then lets update the DT and
set the correct bitmap...
Again world is a bad place and reality is that this cause wonderful
regression in some case of by extreme luck the first ever connected
port working and the rest of the switch dead.
The problem has been bisected to all the device that doesn't have the
PORT1 declared in any of the bitmap.
With this prefaction in mind, on to the REAL problem.
malibu_phy_hw_init FOR SOME REASON, set a global variable first_phy_addr
to the first detected PHY addr that coincidentally is always PORT1.
PORT1 addr is 0x0. The entire code in malibu_phy use this variable to
derive the phy addrs in some function.
Declaring a bitmap where the PORT1 is missing (or worse PORT4 the only
one connected) result in first_phy_addr set to 1 or whatever phy addr is
detected first setting wrong value all over the init stage.
To fix this, introduce a new binding malibu_first_phy_addr to manually
declare the first phy that the malibu PHY driver should use and permit
to detach it from port bmp detection. The legacy detection is kept for
compatibility reason.
Fixes: #13945
Fixes: 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com> # Qnap 301W
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 8cce00bc9d.
The confusion was real and this change cause regression on other
advanced devices that makes actual use of the first_phy_addr value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some local patches have been sent to upstream and they are slightly
different from the upstream version. So it's better to replace them
to avoid conflicts with the new mac80211 backport driver. The
different parts have been merged into patch 996.
This commit also includes some additional fixes:
* Fix watchdog function.
* Improve MT7620 register initialization.
* Introduce DMA busy watchdog for rt2800.
P.S.
Sometimes rt2800 series chips may fall into a DMA busy state. The
tx queues become very slow and the client cannot connect to the AP.
Usually, We can see a lot of hostapd warnings at this point:
'hostapd: IEEE 802.11: did not acknowledge authentication response'
The DMA busy watchdog can help the driver automatically recover
from this abnormal state. By the way, setting higer 'cell_density'
and disabling 'disassoc_low_ack' can significantly reduce the
probability of the DMA busy.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Kernel 6.1 has introduced support for RTW8822BU network adapter, which
is an USB variant of the rtw8822b 802.11ac chipset family.
Build and install the corresponding module in the rtw88 package
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Current rtw88 build configuration builds modules for all chips supported by
rtw88 driver family. This brings the following issues:
- adding a chip with a different bus is not convenient (all chips currently
depends on PCI)
- some features requirements are not relevant for all chips in family (eg
802.11AC is enforced but RTW88-8723DE is only a 802.11b/g/n chip)
Remove those constraints/issues by adding one module build option per
supported chip, and add intermediate options to properly cascade
dependencies.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
ath9k-htc USB-based adapters also support 5/10MHz channel bandwidth.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
