Backport qca8k fixes for big endian system (to make them working again)
and a patch fixing MDIO conflicts if other PHY are connected and mgmt
eth is used to control the switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch enabling assisted learning for qca8k to fix roaming issue
between BSS and BSS on the same L2 broadcast domain.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Symbol rtl8366_enable_vlan and rtl8366_reset_vlan are also present in
the DSA driver upstream and conflicts as they are EXPORTED.
Rename them to rtl8366_smi_enable_vlan and rtl8366_smi_reset_vlan to fix
the conflict. While at it also make them static and drop the
EXPORT_SYMBOL_GPL as they are not actually used by any other driver and
exporting them is useless.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport pending patch for multi CPU port support on QCA8K. 6.1 already
supports all the requiredt code to change a DSA master port so only this
patch fixing the driver is required.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport various QCA8K fixes patch merged upstream. Refresh any changed
patches due to backports.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
UARTs not used as boot console are currently broken on some MediaTek
targets due to register access depending on the bus clock being enabled.
Add patch to make sure this dependency is always met.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Since 5.15 doesnt have phylink_get_caps I had to modify the backport to
use the old mv88e6393x_phylink_validate instead.
I had to fixup one more instance of port_max_speed_mode as well that is not
present in 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Fix PSE port assignment for 3rd GMAC on MT7988 and make sure dma_addr
is always initialized to prevent potentially accessing uninitialized
stack memory in the error path.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit 5356462ce5.
Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.
It seemed that mtd OF_POPULATED hack resolved probing issues but
apparently not all of them. We got reports about reading MAC using NVMEM
not working and USB controllers not working.
Ref: #10232Fixes: #13412
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This symbol was added by commit 2e6f34faa7e0 ("Input: Add IBM Operation
Panel driver") to v6.1. It depends on I2C so it's available to limited
amount of targets. It needs to be specified thought to allow kernel
configuration.
For bcm53xx this fixes:
IBM Operation Panel driver (INPUT_IBM_PANEL) [N/m/?] (NEW)
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
These suboptions (PLATFORM, FSL_MC and MLX5_VFIO_PCI)
may be prompted for when VFIO is enabled, regardless of
architecture.
These are not related to the main vfio use case
(passthrough of PCIe devices)
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch was wrongly tagged as being part of Linux 6.0 even though it
was only committed with Linux 6.2 and hence needs to be backported for
Linux 6.1.
Fixes: fa79baf4a6 ("generic: copy backport, hack, pending patch and config from 5.15 to 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25: 00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
Backport patch adding support for LED PHY directly in PHY ops struct.
Add new PHYLIB_LEDS config and refresh patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 79af0593a3.
A hack adjusting fw_devlink value was added to workaround issue with
probing device drivers caused by of_platform_populate(). With upstream
mtd commit (the one adding OF_POPULATED) backported there is no need for
that hack anymore.
Ref: 3eebb91317 ("kernel: backport proper fix for mtd preventing devices probing")
Ref: #10232
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This change makes it possible to use the GPIO_OPEN_DRAIN /
GPIO_OPEN_SOURCE Flags when exporting GPIOs via dts.
We need to emulate the open-source or open-drain functionalities for the
initial value, because the used functions (gpiod_direction_output_raw)
do not take this into account.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Rename two patches which were only accepted in Linux 6.2, but were
marked as if they were accepted in Linux 6.1.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
