With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
* Platform data for MT7981 was actually missing and is now added.
* Add support for Winbond W25N01KV 1Gbit chip.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board.
Add pre-built files to fix swig dependencies.
Specification:
- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
1 x 10/100/1000M Ethernet
1 x 10/100M Ethernet
- USB Host:
1 x USB3.0 Type A HOST
1 x USB2.0 OTG (40-pin pin-header)
- Wireless:
RTL8723DU/RTL8821CU
- Power Supply: Type-C 5V
Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Changes:
9dc0800 wireless-regdb: Update regulatory rules for Philippines (PH)
111ba89 wireless-regdb: Update regulatory rules for Egypt (EG) from March 2022 guidelines
ae1421f wireless-regdb: Update regulatory info for Türkiye (TR)
20e5b73 wireless-regdb: Update regulatory rules for Australia (AU) for June 2023
991b1ef wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
f429bd94f99e system-linux: switch to new ETHTOOL_xLINKSETTINGS API
Fixes AN announcement for speeds beyond 1 GBit/s.
Adds new UCI options for Ethernet devices:
- autoneg: switch on or off auto-negotiation
- pause: if set to 0, do not announce symmetric flow control capability
- asym_pause: if set to 0, do not announce asymmetric flow control
capability.
- rxpause: if set overrides AN and forces RX pause accordingly
- txpause: if set overrides AN and forces TX pause accordingly
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
db3934d2f740 scripts/netifd-wireless.sh: properly fix WPA3 Enterprise support
Support the following values for the different WPA3 Enterprise modes:
- wpa3-mixed: WPA3 Enterprise transitional mode
This supports EAP with both SHA1 and SHA-256, with optional MFP
- wpa3: WPA3 Enterprise only mode
This supports only SHA256 with mandatory MFP
- wpa3-192: WPA3 Enterprise with mandatory 192 bit support
This uses only GCMP-256 ciphers
Disable 192 bit support and GCMP-256 ciphers for the regular "wpa3" mode.
It seems that even leaving in optional 192 bit support breaks auth on some
clients, including iOS devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
WPA3 Enterprise-transitional requires optional MFP support and SHA1+SHA256
WPA3 Enterprise-only requires SHA1 support disabled and mandatory MFP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Arm platforms with the right hardware blocks (such as
GICv3.0+ interrupt controller and SMMU/IOMMU) are
able to use vfio-pci to pass through PCI devices
to a VM.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The vfio module only exposes the enable_unsafe_noiommu_mode parameter
if CONFIG_VFIO_NOIOMMU is enabled. When it isn't, the module
will complain about an unknown parameter:
vfio: unknown parameter 'enable_unsafe_noiommu_mode' ignored
As CONFIG_VFIO_NOIOMMU is disabled by the module package,
we can remove the module loading parameter.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Always enable built-in 2.5G PHY on MT7988 for now, so that it can be
used. In future it would be nice to be able to switch power and MDIO
access via address 0 at run-time in Linux, both, to be able to use
external PHYs at address 0 and to reduce power consumption on systems
not using the built-in 2.5G PHY.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.
To install this U-Boot build to the eMMC:
opkg install mmc-utils partx-utils
mmc bootpart enable 1 1 /dev/mmcblk0
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
partx -a /dev/mmcblk0
dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Compile-tested: all boards
Runtime-tested:
- Cortex-A8: pcDuino
- Cortex-A7: Bananapro, Bananapi M3
- Cortex-A53:Pine64+
Notes:
- binman tries to add firmware for the SCP (system control processor), which
we don't build, and is optional for the boot process on 64-bit. Disable this
via setting the SCP envvar to /dev/null. For further info, see [1] .
[1] https://github.com/u-boot/u-boot/blob/master/board/sunxi/README.sunxi64
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
vhost-net is used to accelerate traffic to virtualisation
guests that use the virtio-net network card in QEMU.
Generally it is invoked by specifying "vhost=on" to a
QEMU -netdev device:
qemu-system-aarch64 -nographic -M virt -cpu host \
--enable-kvm -bios u-boot.bin -smp 1 -m 2048 \
-drive file=openwrt-armsr-armv8.img,format=raw,index=0,media=disk \
-device "virtio-net,netdev=landev,disable-legacy=off,disable-modern=off" \
-netdev "tap,id=landev,helper=/usr/lib/qemu-bridge-helper --br=br-lan,vhost=on"
Signed-off-by: Mathew McBride <matt@traverse.com.au>
We have to move to use git clone as there are no newer tagged releases.
Changes:
604f8f5 Default CROSS_CM3 to arm-none-eabi- instead of armv7m-softfloat-eabi-
b9b9419 Tidy up license information
0290b2c wtmi: Fix typo
a10b8e9 Makefile: fix a53-firmware.bin generation (maximum size is not optimal)
f654082 wtmi: Add const qualifier to isr_vector
4a43a3b wtmi: Improve detection of ESPRESSObin boards with Topaz
189e629 wtmi: Improve detection of boards with insufficient MDIO pull-up
3dac4fe wtmi: Fix detection of Armada 3720 Devel Board
3ca4dfa Bump mox-imager commit
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
1de442d Convert floating point operations to integer operations
ce6770d Modify mv_ddr4_calibration_validate function body to match function header
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
a3e1c67 wtmi: Fix linker output sections
f65e3bf wtmi: Remove usage of non-existant string.h file and memcpy() function
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Recent envtools update to 2023.07.02 has introduced a breakage when trying
to parallel build with the following error:
/bin/sh: line 1: scripts/basic/fixdep: No such file or directory
Luckily it can easily be reproduced locally via a simple script so it was
not hard to bisect it down to upstream commit [1].
However, its not that commits fault, it just uncovered an issue with the
way we have been building envtools for a long time, maybe even from the
package introduction.
The issue is that we are trying to build envtools as one of the U-Boot
no-dot-config-targets but envtools was newer a valid target for it but
since we were creating the config headers that were not actually used it
was actually building all this time.
Since the blamed commit [1] a tool called printinitialenv is built and
now a proper config is actually required in order for prerequisites to
get built properly.
So, in order to properly fix this (Hopefully for good) lets stop pretending
that envtools are a valid no-dot-config-targets target and use the
tools-only defconfig which is meant exactly for just building the tools.
This will make a minimal config for the U-Boot sandbox target and then
envtools will build just fine in parallel mode (I tested with 32 threads).
We do hovewer need to override the ARCH passed by OpenWrt and set it to
sandbox as otherwise U-Boot will not find the required headers because the
ARCH is being overriden to an incorrect one.
[1] 40b77f2a3a
Fixes: 9db0330052 ("uboot-envtools: update to 2023.07.02")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
WED requires a bunch of additional reserved memory regions. As U-Boot's
LMB allocator defaults to a maximum of only 8 regions, this currently
makes using WED impossible.
Raise LMB_MAX_REGIONS to 64 just like for all other MediaTek boards
with a SoC supporting WED.
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When the STA is brought up, it is set to DISABLED before adding the bss to ucode,
so the first trigger to disable the AP is missed.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During the channel scanning process, the driver will continuously
switch channels. It seems that the full RF calibration step in
rt2800_config_channel() caused the channel scanning function to
timeout. To fix it, move the RF calibration to rt2800_enable_radio()
so that it is only executed once. This commit also includes some
coding format adjustments to follow the Linux recommended style.
Fixes: 2824fa6963 ("mac80211: rework MT7620 PA/LNA RF calibration")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
