The clocks for SPI busses were named wrongly which resulted in the
spi-mt65xx driver not requesting them. This has apparently been
worked around by marking the clocks required for SPI0 which is used
for SPI-NOR and SPI-NAND flash chips as critical.
Fix the device tree for all 3 generic SPI host controllers and no
longer mark clocks as critical.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b173ab730)
Fix in commit 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:
ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.
Fixes: 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16809
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.58..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
It should be debounce-interval, as with the others.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16802
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit ec8f647d16, as with the
current kernel version, the change actually causes the same bug it once
may have fixed -- that is, the leds are now again reversed.
I suspect this was due to a switch to a newer kernel version between when
the patch was submitted and now reversing the order of the interfaces, so
that eth0 / the LAN interface is also the interface used for PoE, and eth1
/ the WAN interface is the non-PoE interface.
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16779
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop removal of firewall4 package for I2SE Duckbill device.
With OPKG the firewall4 package was installed anyway as it's a
dependency of luci-app-firewall and was silently installed again later
in such condition. Drop it to fix support for APK.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop removal of firewall4 package for Synology DS213j device.
With OPKG the firewall4 package was installed anyway as it's a
dependency of luci-app-firewall and was silently installed again later
in such condition. Drop it to fix support for APK.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
RouterBOOT v7 on NOR devices no longer accepts the YAFFS kernel ELF
method of booting. It will accept an NPK image named bootimage.
Adjust mtdsplit_minor to accept this second possible boot file name.
Use the conservative value of 127 for YAFFS max name length (used when
YAFFS compiled with unicode support) vs 255.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/16780
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduced with Linux 6.7, in commit:
5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the MiNOR mtdsplit driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
This mtdsplit parser makes a very limited check of the first YAFFS
header. For example, this will not match expectations when initially booting
an initramfs image with OEM on MTD.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Acked-by: Thibaut VARENE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/16780
Signed-off-by: Robert Marko <robimarko@gmail.com>
It does the same thing minus a few dmesg prints.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16788
Signed-off-by: Robert Marko <robimarko@gmail.com>
The WiFi chips are actually on PCIe1 and PCIe2, PCIe0 is empty. Fix the
assignment so that WiFi works properly again.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/16807
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop limitation on depending on only armv8 for armsr target as those
module should support both 32 and 64 bits systems.
Only thunderx-net actually require 64 bit systems.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop fmc and fmc-eth-config package as they were never actually
submitted to openwrt mainline and they don't exist around.
They are probably part of NXP SDK and were added due to copy-paste
errors.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add the '~' prefix to package that needs to skip installation as they
are meta-package just to download and compile firmware package for the
final firmware.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop kmod-i2c-ralink from ASUS RP-AC56 as it was wrongly added. Such
kmod is not supported on mt7621 as i2c is handled by the mediatek driver
and not bay the ralink downstream one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix wrong package device list that is trying to remove deprecated
packages. Replace with new variant where possible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop ipq-wifi-teltonika_rutx from Teltonika RUTX50, the board file was
merged upstream but the ipq package was never dropped from
DEVICE_PACKAGES list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop kmod-ledtrig-default-on and kmod-ledtrig-netdev as the kmod were
dropped and are now enabled by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This GPIO is pulled down by the onboard MCU when the power button
is pressed for 5 seconds, indicating a user-initiated shutdown.
Refresh patches at the same time.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Although Zyxel XGS1210 devices are not yet officially supported there
are several patches floating around to enable them. This is a very imporant
one because it fixes a SMI misconfiguration. In the known DTS the SFP+
port settings are set as follows.
phy26: ethernet-phy@26 {
compatible = "ethernet-phy-ieee802.3-c45";
phy-is-integrated;
reg = <26>;
sds = < 8 >;
};
phy27: ethernet-phy@27 {
compatible = "ethernet-phy-ieee802.3-c45";
phy-is-integrated;
reg = <27>;
sds = < 9 >;
};
So these are PHYs linked to an internal SerDes. During initialization
rtl838x_mdio_init() generates smi_bus=0 & smi_addr=27/28 for these ports.
Although this seems like a valid configuration integrated PHYs attached
to an SerDes do not have an SMI bus. Later on the mdio reset wrongly feeds
the SMI registers and as a result the PHYs on SMI bus 0 do not work.
Without patch (loaded with rtk network on & initramfs):
...
mdio_bus mdio-bus: MDIO device at address 0 is missing.
mdio_bus mdio-bus: MDIO device at address 1 is missing.
mdio_bus mdio-bus: MDIO device at address 2 is missing.
mdio_bus mdio-bus: MDIO device at address 3 is missing.
mdio_bus mdio-bus: MDIO device at address 4 is missing.
mdio_bus mdio-bus: MDIO device at address 5 is missing.
mdio_bus mdio-bus: MDIO device at address 6 is missing.
mdio_bus mdio-bus: MDIO device at address 7 is missing.
...
rtl83xx-switch ... : no phy at 0
rtl83xx-switch ... : failed to connect to PHY: -ENODEV
rtl83xx-switch ... : error -19 setting up PHY for tree 0, switch 0, port 0
rtl83xx-switch ... : no phy at 1
rtl83xx-switch ... : failed to connect to PHY: -ENODEV
rtl83xx-switch ... : error -19 setting up PHY for tree 0, switch 0, port 1
...
With patch (loaded with rtk network on & initramfs):
...
rtl83xx-switch ... : PHY [mdio-bus:00] driver [REALTEK RTL8218D] (irq=POLL)
rtl83xx-switch ... : PHY [mdio-bus:01] driver [REALTEK RTL8218D] (irq=POLL)
...
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL930x have only 4 SMI busses (0-3) and the XGS1250 SFP port ist
directly managed. Remove the wrong configuration in the dts.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently RTL8218D detection works for a range of devices. That can lead to
false positives. E.g. RTL8218B or RTL8214FC are covered by the detection mask
as well. That is wrong. Nail detection down to the real RTL8218D phy id.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
The detection of the RTL8214C is a little complicated. Make it easier.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
Three PHYs share the same identifier. Until now we simply assume
the type depending of the bus address it is attached to. Make it
better and check the chip mode register instead.
The kernel will either detect by id/mask or by match_phy_device().
Remove the unneeded settings.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
The number of phy pages differ between RTL838X and RTL839X. Make that
clear and adapt the existing defines.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
According to the specs the RTL839x provides up to 8192 phy pages.
Especially the "raw" page 8191 is used for different initialization
tasks. Increase the limit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL930x devices need the USXGMII mode. This is a final leftover
from the 6.6 conversion.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16457
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add memory regions and devices used for wireless offloading to the
device tree for MT7988.
This allows using WED on devices with MT7988 SoC and MT7995E, MT7996E or
MT7992E wireless controllers.
Devices with 4 GiB of RAM (or more) will still need ajustments to avoid
running out of swiotlb entries.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit adds OpenWRT's LED aliases to the board DTS
for showing system status on the NanoPi R3S.
Signed-off-by: Kevin Zhang <kevin@kevinzhang.me>
Link: https://github.com/openwrt/openwrt/pull/16738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the FriendlyElec NanoPi R3S.
CPU: Rockchip RK3566, Quad-core Cortex-A55
RAM: 2GB LPDDR4X
Ethernet: GMAC RTL8211F GbE, PCIe R8111H GbE
USB3.0 Host: Type-A x1
Storage: MicroSD Slot x 1, and optional on-board 32GB eMMC
Debug Serial Port: 3.3V TTL, 3-pin 2.54mm pitch connector, 1500000 bauds
LED: LED x 3
RTC: One low-power RTC, supports backup battery input
Both GbE controllers are working (WAN eth0, LAN eth1).
Appropriate LAN/WAN interface assignments and MAC address generation.
All three LEDs are working.
USB appears to be working and has been tested with mass storage.
Installation - microSD:
-Uncompress the OpenWRT sysupgrade.img.gz
-Write image to microSD card using dd or similar tool
Installation - eMMC:
-Boot from microSD
-Uncompress the OpenWRT sysupgrade.img.gz
-Flash to eMMC : dd if=x.img of=/dev/mmcblk0
-sync
-Remove microSD card
-Reboot
Signed-off-by: Kevin Zhang <kevin@kevinzhang.me>
Link: https://github.com/openwrt/openwrt/pull/16738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No need for irq_of_parse_and_map since this is in _probe.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16771
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The option shows up when kmod-dm and CONFIG_KERNEL_AUDIT are selected.
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
Link: https://github.com/openwrt/openwrt/pull/16793
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
commit eee3c695f3 ("linux-firmware: add offloading firmware for MT7988")
added mt7988_wo_{0,1}.bin in the 'mediatek/mt7988' directory while driver
currently expects the files in the 'mediatek' directory.
Import pending patch which changes the path in the driver header now
that the firmware has been added.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Clarify compatibility of the two subtargets with different SoCs to
reduce confusion. The added SoC names only differ in small details such
as features enabled (PoN vs DSL for example).
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/16785
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This converts all RT3662 and RT3883 devices to use interrupt based
gpio-keys instead of gpio-keys-polled. The poll-interval will be
removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
This converts all RT305x and RT5350 devices to use interrupt based
gpio-keys instead of gpio-keys-polled. The poll-interval will be
removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
This converts all RT2880 devices to use interrupt based gpio-keys
instead of gpio-keys-polled. The poll-interval will be removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
All other MT76x8 devices have already been migrated to gpio-keys.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Ralink GPIO driver supports irqchip function. Hence we need to
add "interrupt-parent" and "interrupt-controller" properties to make
sure it works properly. It is worth noting that all GPIO devices
share the same interrupt line.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
The gpiolib has already introduced a general GPIO irqchip framework
to initialize the GPIO irqchip[1]. This patch will make use of it
to simplify the legacy Ralink GPIO driver codes. This patch also
includes some code readability improvements.
[1] 1425052097b5 ("gpio: add IRQ chip helpers in gpiolib")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's shared by all targets. Unlike the other shared symbols, it's not
removed by kernel_oldconfig.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16756
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Airoha EN7581 got renamed to AN7581 due to move from Econet to
Airoha.
To save on compatibility, use both compatible for the device.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
